KARUMO TTI

EEE LEVEL 6 EPL NOTES

Corona Effect in Power System

Electric power transmission practically deals in the bulk transfer of electrical energy,
from generating stations situated many kilometers away from the main consumption
centers or the cities. For this reason, the long distance transmission cables are of
utmost necessity for effective power transfer, which in-evidently results in huge losses
across the system. Minimizing those has been a major challenge for power engineers
of late and to do that one should have a clear understanding of the type and nature of
losses. One of them being the corona effect in power system, which has a
predominant role in reducing the efficiency of EHV(extra high voltage lines) which
we are going to concentrate on, in this article.

What is Corona Effect in Power System and Why it Occurs?

For corona effect to occur effectively, two factors here are of prime importance as
mentioned below:-
1) Alternating electrical potential difference must be supplied across the line.
2) The spacing of the conductors, must be large enough compared to the line diameter.

When an alternating current is made to flow

across two conductors of the transmission line whose spacing is large compared to
their diameters, then air surrounding the conductors (composed of ions) is subjected to
di-electric stress. At low values of supply end voltage, nothing really occurs as the
stress is too less to ionize the air outside. But when the potential difference is made to
increase beyond some threshold value of around 30 kV known as the critical
disruptive voltage, then the field strength increases and then the air surrounding it
experiences stress high enough to be dissociated into ions making the atmosphere
conducting. This results in electric discharge around the conductors due to the flow of
these ions, giving rise to a faint luminescent glow, along with the hissing sound
accompanied by the liberation of ozone, which is readily identified due to its
characteristic odor. This phenomena of electrical discharge occurring in transmission
line for high values of voltage is known as the corona effect in power system. If the
voltage across the lines is still increased the glow becomes more and more intense
along with hissing noise, inducing very high power loss into the system which must
be accounted for.

Factors Affecting Corona Effect in Power System.

As mentioned earlier, the line voltage of the conductor is the main determining factor
for corona in transmission lines, at low values of voltage (lesser than critical
disruptive voltage) the stress on the air is too less to dissociate them, and hence no
electrical discharge occurs. Since with increasing voltage corona effect in a
transmission line occurs due to the ionization of atmospheric air surrounding the
cables, it is mainly affected by the conditions of the cable as well as the physical state
of the atmosphere. Let us look into these criterion now with greater details :
Atmospheric Conditions for Corona in Transmission Lines

It has been physically proven that the voltage gradient for di-electric breakdown of air
is directly proportional to the density of air. Hence in a stormy day, due to continuous
air flow the number of ions present surrounding the conductor is far more than
normal, and hence its more likely to have electrical discharge in transmission lines on
such a day, compared to a day with fairly clear weather. The system has to designed
taking those extreme situations into consideration.

Condition of Cables for Corona in Transmission Line.

This particular phenomena depends highly on the conductors and its physical
condition. It has an inverse proportionality relationship with the diameter of the
conductors. i.e. with the increase in diameter, the effect of corona in power system
reduces considerably.
Also the presence of dirt or roughness of the conductor reduces the critical breakdown
voltage, making the conductors more prone to corona losses. Hence in most cities and
industrial areas having high pollution, this factor is of reasonable importance to
counter the ill effects it has on the system.

Spacing between Conductors

As already mentioned, for corona to occur effectively the spacing between the lines
should be much higher compared to its diameter, but if the length is increased beyond
a certain limit, the di-electric stress on the air reduces and consequently the effect of
corona reduces as well. If the spacing is made too large then corona for that region of
the transmission line might not occur at all.

Short Transmission Line

The transmission lines which have length less than 80 km are generally referred as
short transmission lines.
For short length, the shunt capacitance of this type of line is neglected and other
parameters like electrical resistance and inductor of these short lines are lumped,
hence the equivalent circuit is represented as given below,

Let’s draw the vector diagram for this equivalent circuit, taking receiving end current
Ir as reference. The sending end and receiving end voltages make angle with that
reference receiving end current, of φs and φr, respectively.

As the shunt capacitance of the line is neglected, hence sending end current and
receiving end current is same, i.e.

I s = I r.

Now if we observe the vector diagram carefully, we will get,

Vs is approximately equal to
Vr + Ir.R.cosφr + Ir.X.sinφr

That means,

Vs ≅ Vr + Ir.R.cosφr + Ir.X.sinφr as the it is assumed that φs ≅ φr

As there is no capacitance, during no load condition the current through the line is
considered as zero, hence at no load condition, receiving end voltage is the same as
sending end voltage.

As per dentition of voltage regulation of power transmission line,

Here, vr and vx are the per unit resistance and reactance of the short transmission line.

Any electrical network generally has two input terminals and two output terminals. If
we consider any complex electrical network in a black box, it will have two input
terminals and output terminals. This network is called two - port network. Two port
model of a network simplifies the network solving technique. Mathematically a two
port network can be solved by 2 by 2 matrix.

A transmission as it is also an electrical network, line can be represented as two port

network.

Hence two port network of transmission line can be represented as 2 by 2 matrixes.

Here the concept of ABCD parameters comes. Voltage and currents of the network
can represented as ,

Where A, B, C and D are different constant of the network.

If we put Ir = 0 at equation (1), we get,

Hence, A is the voltage impressed at the sending end per volt at the receiving end
when receiving end is open. It is dimension less.

If we put Vr = 0 at equation (1), we get

That indicates it is impedance of the transmission line when the receiving terminals
are short circuited. This parameter is referred as transfer impedance.

C is the current in amperes into the sending end per volt on open circuited receiving
end. It has the dimension of admittance.

D is the current in amperes into the sending end per amp on short circuited receiving
end. It is dimensionless.

Now from equivalent circuit, it is found that,

Vs = Vr + IrZ and Is = Ir
Comparing these equations with equation 1 and 2

we get,
A = 1, B = Z, C = 0 and D = 1. As we know that the constant A, B, C and D are
related for passive network as,

AD − BC = 1.
Here, A = 1, B = Z, C = 0 and D = 1
⇒ 1.1 − Z.0 = 1
So the values calculated are correct for short transmission line.
From above equation (1),

When Ir = 0 that means receiving end terminals is open circuited and then from the
equation 1, we get receiving end voltage at no load.

and as per definition of voltage regulation of power transmission line,

Efficiency of Short Transmission Line

The efficiency of short line as simple as efficiency equation of any other electrical
equipment, that means

R is per phase electrical resistance of the transmission line.

Medium Transmission Line

The transmission line having its effective length more than 80 km but less than 250
km, is generally referred to as a medium transmission line. Due to the line length
being considerably high, admittance Y of the network does play a role in calculating
the effective circuit parameters, unlike in the case of short transmission lines. For this
reason the modelling of a medium length transmission line is done using lumped
shunt admittance along with the lumped impedance in series to the circuit.These
lumped parameters of a medium length transmission line can be represented using two
different models, namely-
1) Nominal Π representation.

2) Nominal T representation.

Let’s now go into the detailed discussion of these above mentioned models.

Nominal Π Representation of a Medium Transmission Line

In case of a nominal Π representation, the lumped series impedance is placed at the

middle of the circuit where as the shunt admittances are at the ends. As we can see
from the diagram of the Π network below, the total lumped shunt admittance is
divided into 2 equal halves, and each half with value Y ⁄ 2 is placed at both the
sending and the receiving end while the entire circuit impedance is between the two.
The shape of the circuit so formed resembles that of a symbol Π, and for this reason it
is known as the nominal Π representation of a medium transmission line. It is mainly
used for determining the general circuit parameters and performing load flow analysis.

As we can see here, VS and VR is the supply and receiving end voltages respectively,
and
Is is the current flowing through the supply end.
IR is the current flowing through the receiving end of the circuit.
I1 and I3 are the values of currents flowing through the admittances. And
I2 is the current through the impedance Z.
Now applying KCL, at node P, we get.

Similarly applying KCL, to node Q.

Now substituting equation (2) to equation (1)

Now by applying KVL to the circuit,

Comparing equation (4) and (5) with the standard ABCD parameter equations

We derive the parameters of a medium transmission line as:

Nominal T Representation of a Medium Transmission Line

In the nominal T model of a medium transmission line the lumped shunt admittance
is placed in the middle, while the net series impedance is divided into two equal
halves and and placed on either side of the shunt admittance. The circuit so formed
resembles the symbol of a capital T, and hence is known as the nominal T network of
a medium length transmission line and is shown in the diagram below.

Here also Vs and Vr is the supply and receiving end voltages respectively, and
Is is the current flowing through the supply end.
Ir is the current flowing through the receiving end of the circuit.

Let M be a node at the midpoint of the circuit, and the drop at M, be given by Vm.

Applying KVL to the above network we get,

Now the sending end current is,

Substituting the value of VM to equation (9) we get,

Again comparing equation (8) and (10) with the standard ABCD parameter equations,

The parameters of the T network of a medium transmission line are

Long Transmission Line

A power transmission line with its effective length of around 250 Kms or above is
referred to as a long transmission line. Calculations related to circuit parameters
(ABCD parameters) of such a power transmission is not that simple, as was the case
for a short transmission line or medium transmission line.