ASME B16.

5-2009

Table 17 Templates for Drilling Class 900 Pipe Flanges and Flanged Fittings
O
L

Point height [Note (1)]

Flange Stud Bolt With Nuts

1 2 3 4 5 6 7 8 9

Length of Bolts,
L
Drilling [Notes (2), (3)] [Notes (1), (4)]
Nominal Outside
Pipe Diameter Diameter of Diameter of
Size, of Flange, Bolt Circle, Bolt Holes, Number of Diameter of 7-mm Male and Female/
NPS O W in. Bolts Bolts, in. Raised Face Tongue and Groove Ring Joint
1
⁄2
3
⁄4
1
Use Class 1500 dimensions in these sizes
11⁄4
11⁄2
2
21⁄2
7
3 240 190.5 1 8 ⁄8 145 140 145
4 290 235.0 11⁄4 8 11⁄8 170 165 170
5 350 279.4 13⁄8 8 11⁄4 190 185 190
6 380 317.5 11⁄4 12 11⁄8 190 185 195
8 470 393.7 11⁄2 12 13⁄8 220 215 220
10 545 469.9 11⁄2 16 13⁄8 235 230 235
12 610 533.4 11⁄2 20 13⁄8 255 250 255
14 640 558.8 15⁄8 20 11⁄2 275 265 280
16 705 616.0 13⁄4 20 15⁄8 285 280 290
18 785 685.8 2 20 17⁄8 325 320 335
20 855 749.3 21⁄8 20 2 350 345 360
24 1,040 901.7 25⁄8 20 21⁄2 440 430 455

GENERAL NOTES:
(a) Dimensions of Table 17 are in millimeters, except for diameters of bolts and bolt holes, which are in inch units. For dimensions in inch
units, refer to Mandatory Appendix II, Table II-17.
(b) For other dimensions, see Tables 18 and 19.
NOTES:
(1) The length of the stud bolt does not include the height of the points (see para 6.10.2).
(2) For flange bolt holes, see para. 6.5.
(3) For spot facing, see para. 6.6.
(4) Bolt lengths not shown in the table may be determined in accordance with Nonmandatory Appendix C (see para. 6.10.2).

94
 ASME B16.5-2009

Table 18 Dimensions of Class 900 Flanges

X [Note (1)] X [Note (1)]
Q B

T tf Y Y
tf

O O
Threaded Slip-On Welding

X [Note (1)]
B

Y
r tf

O
Lapped
X
Ah

O B Y

tf tf

Blind O
Welding Neck
Table 18 Dimensions of Class 900 Flanges (Cont’d)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Hub Diam. Minimum Corner

Beginning Thread Bore
Outside of Chamfer Length Radius of Minimum
Length Through Hub Bore
Nom. Diam. Min. Diam. Welding Threaded Lapped Counterbore
Pipe of Thickness of Neck, Threaded/ Welding Flange, Min. Min. Welding Flange Threaded
Size, Flange, of Flange, Hub, Ah Slip-On, Lapped, Neck, T Slip-On, Lapped, Neck, and Pipe, Flange,
NPS O tf X [Note (2)] Y Y Y [Note (3)] B B B r Q

1
⁄2
3
⁄4
1
11⁄4 Use Class 1500 dimensions in these sizes [Note (4)]
11⁄2
2
21⁄2

3 240 38.1 127 88.9 54 54 102 42 90.7 91.4 Note (5) 10 92.2
4 290 44.5 159 114.3 70 70 114 48 116.1 116.8 Note (5) 11 117.6

5 350 50.8 190 141.3 79 79 127 54 143.8 144.4 Note (5) 11 144.4
6 380 55.6 235 168.3 86 86 140 58 170.7 171.4 Note (5) 13 171.4
8 470 63.5 298 219.1 102 114 162 64 221.5 222.2 Note (5) 13 222.2
10 545 69.9 368 273.0 108 127 184 72 276.2 277.4 Note (5) 13 276.2
12 610 79.4 419 323.8 117 143 200 77 327.0 328.2 Note (5) 13 328.6

14 640 85.8 451 355.6 130 156 213 83 359.2 360.2 Note (5) 13 360.4
16 705 88.9 508 406.4 133 165 216 86 410.5 411.2 Note (5) 13 411.2
18 785 101.6 565 457.0 152 190 229 89 461.8 462.3 Note (5) 13 462.0
20 855 108.0 622 508.0 159 210 248 93 513.1 514.4 Note (5) 13 512.8
24 1,040 139.7 749 610.0 203 267 292 102 616.0 616.0 Note (5) 13 614.4

95

ḷ߶࠶ӛ㖁ZZZE]I[ZFRP‫ݽ‬䍩л䖭
 ASME B16.5-2009

Table 18 Dimensions of Class 900 Flanges (Cont’d)

GENERAL NOTES:
(a) Dimensions of Table 18 are in millimeters. For dimensions in inch units, refer to Mandatory Appendix II, Table II-18.
(b) For tolerances, see section 7.
(c) For facings, see para. 6.4.
(d) For flange bolt holes, see para. 6.5 and Table 17.
(e) For spot facing, see para 6.6.
(f) For reducing threaded and slip-on flanges, see Table 6.
(g) Blind flanges may be made with or without hubs at the manufacturer’s option.
(h) For reducing welding neck flanges, see para. 6.8.
NOTES:
(1) This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on threaded, slip-on, socket-welding, and
lapped flanges. This dimension is defined as the diameter at the intersection between the hub taper and back face of the flange.
(2) For welding end bevel, see para. 6.7.
(3) For thread of threaded flanges, see para. 6.9.
(4) Socket welding flanges may be provided in NPS 1⁄2 through NPS 21⁄2, using Class 1500 dimensions.
(5) To be specified by the Purchaser.

96
 ASME B16.5-2009

Table 19 Templates for Drilling Class 1500 Pipe Flanges

O
L

Point height [Note (1)]

Flange Stud Bolt With Nuts

1 2 3 4 5 6 7 8 9
Length of Bolts,
L
Drilling [Notes (2), (3)] [Notes (1), (4)]
Outside
Nominal Diameter Diameter of Diameter of Diameter of
Pipe Size, of Flange, Bolt Circle, Bolt Holes, Number of Bolts, 7-mm Male and Female/
NPS O W in. Bolts in. Raised Face Tongue and Groove Ring Joint
1 7 3
⁄2 120 82.6 ⁄8 4 ⁄4 110 100 110
3 7 3
⁄4 130 88.9 ⁄8 4 ⁄4 115 110 115
7
1 150 101.6 1 4 ⁄8 125 120 125
11⁄4 160 111.1 1 4 7
⁄8 125 120 125
11⁄2 180 123.8 11⁄8 4 1 140 135 140
7
2 215 165.1 1 8 ⁄8 145 140 145
21⁄2 245 190.5 11⁄8 8 1 160 150 160
3 265 203.2 11⁄4 8 11⁄8 180 170 180
4 310 241.3 13⁄8 8 11⁄4 195 190 195

5 375 292.1 15⁄8 8 11⁄2 250 240 250

6 395 317.5 11⁄2 12 13⁄8 260 255 265
8 485 393.7 13⁄4 12 15⁄8 290 285 300
10 585 482.6 2 12 17⁄8 335 330 345
12 675 571.5 21⁄8 16 2 375 370 385

14 750 635.0 23⁄8 16 21⁄4 405 400 425

16 825 704.8 25⁄8 16 21⁄2 445 440 470
18 915 774.7 27⁄8 16 23⁄4 495 490 525
20 985 831.8 31⁄8 16 3 540 535 565
24 1 170 990.6 35⁄8 16 31⁄2 615 610 650

GENERAL NOTES:
(a) Dimensions of Table 19 are in millimeters, except for the diameters of the bolts and bolt holes, which are in inch units. For dimensions
in inch units, refer to Mandatory Appendix II, Table II-19.
(b) For other dimensions, see Table 20.
NOTES:
(1) The length of the stud bolt does not include the height of the points (see para. 6.10.2).
(2) For flange bolt holes, see para. 6.5.
(3) For spot facing, see para. 6.6.
(4) Bolt lengths not shown in the table may be determined in accordance with Nonmandatory Appendix C (see para. 6.10.2).

97

ḷ߶࠶ӛ㖁ZZZE]I[ZFRP‫ݽ‬䍩л䖭
 Table 20 Dimensions of Class 1500 Flanges
X [Note (1)] X [Note (1)]
Q B

Y Y
T tf tf

O O
Threaded (NPS 1/ to 21/ Only)
2 2 Slip-On Welding (NPS 1/2 to 21/2 Only)

X [Note (1)]
X [Note (1)] B
B
Col. 10
Y
D r tf
tf Y
O
B
Col. 12 Lapped
O
Socket Welding (NPS 1/2 to 21/2 Only) X

98
Ah
ASME B16.5-2009

O B Y

tf tf

Blind O
Welding Neck

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Length Through Hub Bore

Hub Diameter Minimum
Outside Beginning of Threaded/ Thread Length Minimum Welding Corner Bore Minimum
Diameter Minimum Chamfer Slip-On/ Threaded Slip-On/ Neck/ Radius of Counterbore
Nominal of Thickness Diameter Welding Neck, Socket Welding Flange, Socket Minimum Socket Lapped Flange Threaded Depth of
Pipe Size, Flange, of Flange, of Hub, Ah Welding, Lapped, Neck, T Welding, Lapped, Welding, and Pipe, Flange, Socket,
NPS O tf X [Note (2)] Y Y Y [Note (3)] B B B r Q D
1
⁄2 120 22.3 38 21.3 32 32 60 23 22.2 22.9 Note (4) 3 23.6 10
3
⁄4 130 25.4 44 26.7 35 35 70 26 27.7 28.2 Note (4) 3 29.0 11
1 150 28.6 52 33.4 41 41 73 29 34.5 34.9 Note (4) 3 35.8 13
11⁄4 160 28.6 64 42.2 41 41 73 31 43.2 43.7 Note (4) 5 44.4 14
 Table 20 Dimensions of Class 1500 Flanges (Cont’d)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Length Through Hub Bore

Hub Diameter Minimum
Outside Beginning of Threaded/ Thread Length Minimum Welding Corner Bore Minimum
Diameter Minimum Chamfer Slip-On/ Threaded Slip-On/ Neck/ Radius of Counterbore
Nominal of Thickness Diameter Welding Neck, Socket Welding Flange, Socket Minimum Socket Lapped Flange Threaded Depth of
Pipe Size, Flange, of Flange, of Hub, Ah Welding, Lapped, Neck, T Welding, Lapped, Welding, and Pipe, Flange, Socket,
NPS O tf X [Note (2)] Y Y Y [Note (3)] B B B r Q D

11⁄2 180 31.8 70 48.3 44 44 83 32 49.5 50.0 Note (4) 6 50.6 16

2 215 38.1 105 60.3 57 57 102 39 61.9 62.5 Note (4) 8 63.5 17
21⁄2 245 41.3 124 73.0 64 64 105 48 74.6 75.4 Note (4) 8 76.2 19
3 265 47.7 133 88.9 ... 73 117 ... ... 91.4 Note (4) 10 ... ...
4 310 54.0 162 114.3 ... 90 124 ... ... 116.8 Note (4) 11 ... ...

5 375 73.1 197 141.3 ... 105 156 ... ... 144.4 Note (4) 11 ... ...
6 395 82.6 229 168.3 ... 119 171 ... ... 171.4 Note (4) 13 ... ...
8 485 92.1 292 219.1 ... 143 213 ... ... 222.2 Note (4) 13 ... ...
10 585 108.0 368 273.0 ... 178 254 ... ... 277.4 Note (4) 13 ... ...
12 675 123.9 451 323.8 ... 219 283 ... ... 328.2 Note (4) 13 ... ...

99
14 750 133.4 495 355.6 ... 241 298 ... ... 360.2 Note (4) 13 ... ...
16 825 146.1 552 406.4 ... 260 311 ... ... 411.2 Note (4) 13 ... ...
ASME B16.5-2009

18 915 162.0 597 457.0 ... 276 327 ... ... 462.3 Note (4) 13 ... ...
20 985 177.8 641 508.0 ... 292 356 ... ... 514.4 Note (4) 13 ...
24 1 170 203.2 762 610.0 ... 330 406 ... ... 616.0 Note (4) 13 ... ...

GENERAL NOTES:

ḷ߶࠶ӛ㖁ZZZE]I[ZFRP‫ݽ‬䍩л䖭
(a) Dimensions of Table 20 are in millimeters. For dimensions in inch units, refer to Mandatory Appendix II, Table II-20.
(b) For tolerances, see section 7.
(c) For facings, see para. 6.4.
(d) For flange bolt holes, see para. 6.5 and Table 19.
(e) For spot facing, see para 6.6.
(f) For reducing threaded and slip-on flanges, see Table 6.
(g) Blind flanges may be made with or without hubs at the manufacturer’s option.
(h) For reducing welding neck flanges, see para 6.8.
NOTES:
(1) This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on threaded, slip-on, socket-welding, and lapped flanges. This dimen-
sion is defined as the diameter at the intersection between the hub taper and back face of the flange.
(2) For welding end bevel, see para. 6.7.
(3) For thread of threaded flanges, see para. 6.9.
(4) To be specified by the Purchaser.
 ASME B16.5-2009

Table 21 Templates for Drilling Class 2500 Pipe Flanges

O
L

Point height [Note (1)]

Flange Stud Bolt With Nuts

1 2 3 4 5 6 7 8 9
Length of Bolts,
L
Outside Drilling [Notes (2), (3)] [Notes (1), (4)]
Nominal Diameter Diameter of Diameter of Diameter 7-mm
Pipe Size, of Flange, Bolt Circle, Bolt Holes, Number of of Bolts, Raised Male and Female/
NPS O W in. Bolts in. Face Tongue and Groove Ring Joint
1 7 3
⁄2 135 88.9 ⁄8 4 ⁄4 120 115 120
3 7 3
⁄4 140 95.2 ⁄8 4 ⁄4 125 120 125
7
1 160 108.0 1 4 ⁄8 140 135 140
11⁄4 185 130.2 11⁄8 4 1 150 145 150
11⁄2 205 146.0 11⁄4 4 11⁄8 170 165 170
2 235 171.4 11⁄8 8 1 180 170 180
21⁄2 265 196.8 11⁄4 8 11⁄8 195 190 205
3 305 228.6 13⁄8 8 11⁄4 220 215 230
4 355 273.0 15⁄8 8 11⁄2 255 250 260
5 420 323.8 17⁄8 8 13⁄4 300 290 310
6 485 368.3 21⁄8 8 2 345 335 355
8 550 438.2 21⁄8 12 2 380 375 395
10 675 539.8 25⁄8 12 21⁄2 490 485 510
12 760 619.1 27⁄8 12 23⁄4 540 535 560

GENERAL NOTES:
(a) Dimensions of Table 21 are in millimeters, except for the diameters of the bolts and bolt holes, which are in inch units. For dimensions
in inch units, refer to Mandatory Appendix II, Table II-21.
(b) For other dimensions, see Table 22.
NOTES:
(1) The length of the stud bolt does not include the height of the points (see para. 6.10.2).
(2) For flange bolt holes, see para. 6.5.
(3) For spot facing, see para. 6.6.
(4) Bolt lengths not shown in the table may be determined with Nonmandatory Appendix C (see para. 6.10.2).

100
 ASME B16.5-2009

Table 22 Dimensions of Class 2500 Flanges

X [Note (1)] X [Note (1)]
Q B

tf Y Y
T r tf

O O
Threaded Lapped
(NPS 1/2 to 21/2 Only)
X
Ah

O B Y

tf tf

Blind O
Welding Neck

1 2 3 4 5 6 7 8 9 10 11 12 13

Corner
Hub Diam. Minimum Bore
Beginning Thread Radius of
Outside of Chamfer Length Lapped Minimum
Nom. Diam. Min. Welding Length Through Hub Bore
Threaded Flange Counterbore
Pipe of Thickness Diam. Neck, Welding Flange, Min. Welding and Threaded
Size, Flange, of Flange, of Hub, Ah Threaded, Lapped, Neck, T Lapped, Neck, Pipe, Flange,
NPS O tf X [Note (2)] Y Y Y [Note (3)] B B r Q
1
⁄2 135 30.2 43 21.3 40 40 73 29 22.9 Note (4) 3 23.6
3
⁄4 140 31.8 51 26.7 43 43 79 32 28.2 Note (4) 3 29.0
1 160 35.0 57 33.4 48 48 89 35 34.9 Note (4) 3 35.8
11⁄4 185 38.1 73 42.2 52 52 95 39 43.7 Note (4) 5 44.4
11⁄2 205 44.5 79 48.3 60 60 111 45 50.0 Note (4) 6 50.6

2 235 50.9 95 60.3 70 70 127 51 62.5 Note (4) 8 63.5

21⁄2 265 57.2 114 73.0 79 79 143 58 75.4 Note (4) 8 76.2
3 305 66.7 133 88.9 ... 92 168 ... 91.4 Note (4) 10 ...
4 355 76.2 165 114.3 ... 108 190 ... 116.8 Note (4) 11 ...

5 420 92.1 203 141.3 ... 130 229 ... 144.4 Note (4) 11 ...
6 485 108.0 235 168.3 ... 152 273 ... 171.4 Note (4) 13 ...
8 550 127.0 305 219.1 ... 178 318 ... 222.2 Note (4) 13 ...
10 675 165.1 375 273.0 ... 229 419 ... 277.4 Note (4) 13 ...
12 760 184.2 441 323.8 ... 254 464 ... 328.2 Note (4) 13 ...

101

ḷ߶࠶ӛ㖁ZZZE]I[ZFRP‫ݽ‬䍩л䖭
 ASME B16.5-2009

Table 22 Dimensions of Class 2500 Flanges (Cont’d)

GENERAL NOTES:
(a) Dimensions of Table 22 are in millimeters, except for the diameter of the bolts and bolt holes, which are in inch units. For dimensions
in inch units, refer to Mandatory Appendix II, Table II-22.
(b) For tolerances, see section 7.
(c) For facings, see para. 6.4.
(d) For flange bolt holes, see para. 6.5 and Table 21.
(e) For spot facing, see para 6.6.
(f) For reducing threaded and slip-on flanges, see Table 6.
(g) Blind flanges may be made with or without hubs at the manufacturer’s option.
(h) For reducing welding neck flanges, see para 6.8.
NOTES:
(1) This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on threaded, slip-on,
socket-welding, and lapped flanges. This dimension is defined as the diameter at the intersection between the hub taper and back
face of the flange.
(2) For welding end bevel, see para. 6.7.
(3) For thread of threaded flanges, see para. 6.9.
(4) To be specified by the Purchaser.

102