Name: Instrumentation & Metrology
III B.Tech II Sem(VR20)
Assignment-3 (Unit No-3)
1 Describe unilateral & Bi-lateral tolerance system of tolerances? 2M
2 What is hole basis system of limits & fits with a neat sketch? 2M
3 What is shaft basis system of limits & fits with a neat sketch? 2M
What is Gauge maker’s allowance and ear allowance in design of 2M
4
plug gauges?
5 What is profile gauge and Position Gauge? 2M
Explain the Hole basis and shaft basis limit system with a neat
1(A) 4M
sketch?
The dimensions of the mating parts, according to basic hole system
are given as follows:
(B) Hole: 25.00mm and 25.02mm and Shaft: 24.97mm and 24.95mm. 4M
Find the hole tolerance, shaft tolerance and allowance?
2 (A) Explain the concept of Interchangeability & selective assembly? 4M
A 75mm shaft rotates in a bearing. The Tolerance for both shaft and
bearing is 0.075mm and the required allowance is 0.10mm.
(B) 4M
Determine the dimensions of the shaft and the bearing bore with the
basic hole standard
3 (A) With a neat sketch Describe the working of plug and snap gauges? 4M
4(A) Explain the Taylor’s principles in design of go & No-Go gauges? 4M
Calculate the tolerances, Fundamental deviation and the limits of
(B) sizes for the shaft and hole of the following fit:40mm H8-f7. The 4M
diameter steps are 30mm and 50mm. (Take es= -5.5 D0.41)
Assignment-4 (Unit No-4)
1 What is meant by line standards? Explain with examples? 2M
2 What is meant by end standards? Explain with examples? 2M
Explain the working of Lever type dial test indicators in
3 2M
measurement?
4 Identify the formulae for least count of Micrometer? 2M
5 Explain the working principle of Pneumatic comparators? 2M
6 What is the formula for least count of Vernier bevel Protractor? 2M
7 List the optical measuring Instruments used in measurement? 2M
8 Explain the working of Optical projector with a neat sketch? 2M
9 Sketch any two image patterns of Optical flat? 2M
10 List different types of Mechanical comparators? 2M
What is wringing? Outline the procedure for wringing of Slip
1 (A) 5M
gauges?
(B) Explain the working of angle gauges with a neat sketch? 5M
Explain briefly the construction, working and applications of
2 (A) 5M
Plunger type Dial test indicator with a neat sketch?
Explain the principle of a Micrometer? With a neat sketch the
3 (A) 10M
describe construction and operation of Outside Micrometer?
4 (A) Outline the working of Vernier bevel Protractor? 5M
(B) Describe the working of Reed comparator with a neat sketch? 5M
What is Sine bar? How it is used for angle measurement? Explain
5 (A) 10M
with a neat sketch?
6 (A) Explain the construction and working of Tool maker’s Microscope? 10M
What is the principle of Auto-Collimator? Explain with a neat
7 (A) sketch the construction and working of Injected Graticulate Auto- 10M
Collimator?
8 (A) Describe the Solex Pneumatic gauge with a neat sketch? 10M
Assignment-5(Unit No-5)
Explain any two orders of geometrical irregularities in measurement
1 2M
of surface roughness?
Write and explain the symbol for perpendicularity in direction of
2 2M
lay of surface roughness?
3 Write the ISI symbol for representation of surface roughness? 2M
4 Define the tern Addendum in gear tooth with a neat sketch? 2M
5 Name the instruments used for measurement of surface roughness? 2M
6 Define the tern Module in gear tooth with a neat sketch? 2M
7 What is chordal tooth thickness in measurement of gear tooth? 2M
8 List out any four alignment tests on Lathe machine? 2M
9 List out any four alignment tests on Milling machine? 2M
10 List out any four alignment tests on Drilling machine? 2M
Explain the following terms related to surface roughness with a neat
1 (A) 5M
sketch: (i) Surface Roughness (ii) Waviness (iii) sampling Length
What is the difference between Surface roughness and surface
(B) 5M
waviness?
Explain with a neat sketch the working of Taly-surf in measurement
2 (A) 10 M
of surface roughness?
Explain with a neat sketch the working of Taly-surf in measurement
3 (A) 10 M
of surface roughness?
4 (A) Explain different methods of evaluation of surface roughness? 10 M
5 (A) Explain the nomenclature of Gear tooth with neat sketch? 10 M
Explain the working of Gear tooth vernier caliper in measurement
6 (A) 10 M
of chordal thickness of gear tooth?
7 (A) Describe any five alignment tests on Lathe machines with a neat 10 M
sketch?
8 (A) Describe any five alignment tests on Pillar type drilling machine? 10 M
