CAMERA CORPS

DATAA ODATA B CHANNELB

P PONER
TESTED FOR O LINKB CHANNEL A
ELEcTRICAL SAFETY LINKA
By: LR Date: 01/09/2023 ID SELECT P VIDEO A VÊDEOB AUDIO1 AUDIO2
Next Test Due: 01/09/2024 DATA IN AUDIO1 AUDIO 2 CAT6
314 5/6 --DATA- CAT6
AUX 12V
7I8 HDSD
1/2
HD S.

)
 ASSEMBLY INSTRUCTION
FOR3 PART PLUG (T568A &T5688
PLUG MAIN BODY VWIRING) (CODE:PXCA
-AREA "A"
INSERT
COPPER FOTL

STEPS FIGURES
FIG(1) IMPORTANT POINTS

1.WIRE
SURROUND THE DRAIN
WITH COPPER
FOIL STRIP OðT CABLE JACKET WITH A
(1)-1 (1)-2
(1)-3
LENGTH OF 16mm
ROLL THE COPPER FOIL AND DRAIN
WIRE ON THE CABLE JACKET AS PER
FIG (1) -1~FIG (1)-6

(l)-4 (1)-5 (1)-6

FIG(2) DRAIN WIRE
2,PAIRS
SEPARATE PARTITION
REMOVE THE FOIL SHIELD,
SEPARATE
TWISTED PARS & DRAIN WIRE AS
SHOWN IN FIG (2)
FIG(3) "CUT
3.CUT PARTITION
CUT OUT THE
PARTITION TO THE
EDGE OF THE CABLE
FIG(4) JACKET
INSERT
T568A WIRING
INSERT
4,UNTWIST AND
T568A
BR
W/BR
OR TS68B WIRING
T568B
STRAIGHTEN WRES WIRL BR
W/BR
WIOR
GR WBL
WIGR
UNTWIST THEN STRAIGHTEN THE CORES & WIGR

PRESENT THEM IN THE CORRECT WIOR

FIG(5) ORDER FOR T568A or TS68B

S.CUT OFF
EXCESS WIRES Leave 6. 5~7.0mm wires
protruding
INSERT. Cut off excess length of the
out of the
wires.
FIG(6)

6. PUSH NTO
PLUG MAIN BODY PUT THE
PUSH THEASSEMBLY INTO THE PLUG AND
ASSEMBLY TO THE VERY
OF THE PLUG END
FIG(7)

7.CRIMPING OF
THE PLUG
CRIMP THE PLUG
BEFORE CRIMPING ASSEMBLY COMPLETED
FIG(8) AFTER CRIMPING
8. DRAIN WIRE AREA "A" AFTER CRIMPING, THE DRAIN WIRE
CONTACTED AND COPPER FOIL CONTACTS
METAL SHIELDING AT AREA "A"THE
Overview
The V3 HD StumpCam system consists of the
following parts:
1. Stumps with protective socks
2. Manhole boxes situated in the hole
behind the wickets
3. Boundary box at the boundary
4. Remote control panel (RCP) in the truck

The following sections detail the

functionality of these components.
System Connections

StumpCam Manhole Box

Boundary HD-SDIOUT
StumpCam Manhole Box BoX RCP
HD-SDI OUT

Stumps
Arange of neutral density filters is
necessary, to achieve optimum supplied in the kit. These may be inserted behind the lens, if
exposure.
Focusing is achieved by rotating the whole lens using the supplied lens
The lens can be tilted up to adjusting tool.
achieve the correct framing,

Stump Leads
The stump leads come standard lengths of 8m, 12m and 20m.
An optional set of short lengths (0.25m, 0.5m, 2m) may also be
provided upon request as well an
extra-long 60m cable.
Always inspect the connectors for dirt and damage before mating. Keep the connectors clean,dry
and always use the supplied dust caps.
Avoid connecting and disconnecting stumps while system is powered.

HD StumpCam V3 Operating Manual Vo.1

Manhole Box

Stump Boundary
Box

Mic 1

|Amphendl
Mic 2

HD-SDI Out

Tne vs Manhole Box supports one stump and

connects to the boundary box using a single
Cat5e/Cat6/Cat6a cable.
Two microphone connectors are included for future use.
An HD-SDI output is also provided to aid
framing the image by using a local monitor.
There are two LEDs within the RJ45
connector which indicate the following:
Green LED: Link established
Orange LED: Video present
Manhole to Boundary Cabling
The manhole boxes are connected to the
boundary box using twisted pair cable with 8P8C (RJ45)
terminations. Cat5e, Cat6 and Cat6a may all be used, however the maximum cable length achievable
is related to the category of the cable used:

Cable Type Typical Maximum Length

Cat5e 100m
Cat6 120m
Cat6a 140m

In order to maximise the achievable cable length the following should be considered:

Try to keep cables as short as possible.

Avoid using inline/feed-thru adaptors and patch leads.
Use high quality cables and connectors.

3
HD StumpCam V3 Operating Manual VO.1
 Ensure connectors are correctly crimped and are clean and dry.

Bundling multiple unscreened cables together willintroduce alien crosstalk and may cause reduction
in the maximum working cable length. Using screened cable may help resolve this issue.
Quality of connectors, quality of crimp, condition of cable and connectors all may reduce the
maximum cable length achievable.

Ihe cables should be wired as straight-through Ethernet cables with T-568B pin-out on both ends as
shown below:

RJ-45 Plug
T-5688 Straight-Through Ethernet Cable
1 2 3 4 5 6 7 8
34 5 7 8

PIN 1

T-568B T-568B
ETHERNET ETHERNET
CABLE CABLE

(Cip is pointed avay ftom you)

HD StumpCam V3 Operating Manual V.1

 Boundary Box
The Boundary Box supports two StumpCams and for each channel provides two HD-SDl outputs plus
two line level audio.

Data should be connected to either XLR-3, which are looped. The boundary box routes the data to
each stump depending the position of the ID select rotary switch and which channel is selected on
the RCP.

It is possible to connect one RCP to multiple boundary boxes by either daisy-chaining the data, or
using aY-split cable. Use the rotary ID select switch toassign each boundary box unique lDs.
POWER (Red): Light s toshow that unit is powered
DATA IN (Orange): Flashes when valid data packets are receivedfrom the RCP
DATA AB(Orange): Flashes when the data matches the channel ID for A/B
LINK A/B (Yellow): Lights when the link between boundary box and manhole box has been
esta''shed (there may be a delay in setting up the link on longer cable runs)
VIDEO A/b(Green): Lights when a valid video signal is being received from the connected Manhole
Box

RCP
The RCP communicates with the boundary boxes via RS422. The RS422 output is present on the 9
way d-type connector of the RCP. Use the supplied break-out cable to
to XLR3-M. A regular mic cable can then be used to convert from the 9-way d-type
connect to the boundary Box.
Power is applied to the RCP via the 15-way d-type
the supplied 15-way d-type to XLR4-M connector. The power supply connects to this via
connector.
See the RCP user guide for further
information.

5
HD StumpCam V3 Operating Manual V0.1
Specifications
Stump Camera

1/3" CMOS image

sensor
Video Format: 1080150
M12x0.5 Lens mount (S-Mount)
Available Lenses:
Super Wide (2.8mm Focal Length)
Wide (4.2mm Focal Length)
Tight (16mm Focal Length)
Sensitivity F5.6 2000tx
Minimum llumination F1.4 1.2x
Single coax connection

Manhole Box

Supports one V3 StumpCam

Provides HD-SDl output for local monitoring
Provides RJ45 connector for link to
Boundary Box
Size: 120x 90 x 60mm
Weight: 0.5kg

6
HD StumpCam V3 0perating Manual Vo.1
Boundary Box

Housed in rugged Peli 1500

Supports two StumpCams Case
Provides two HD-SDI outputs per channel
Accepts RS422 data from Camera Corps
RCP via male or female
XLR-3 Universal
Power: 100-240V~ 50/60Hz
Size: 470 x 357 x 176 mm
Weight: 8.5kg

RCP
Camera Corps Universal ROCP via
controlled from a single RS422 (up to six stumps can be
RCP)

Adjustments:
Gain: Auto/Manual 0-30dB
Shutter Speed: Auto/Manual 1/8k -
White Balance 1/50s
Black Balance
Colour Balance
Edge Enhancement

Cable Connections

Stump to Manhole Box:

Coax (Belden 1855A or equivalent)
DIN 1.0/2.3 connectors
Standard Cable lengths: 0.25m, 0.5m,
2m, 8m, 12m, 20m,
6Om
Manhole Box to Boundary Box:
Cat5e/6/6a
RJ45 Connectors
Maximum cable length dependant on cable typelcondltlon
Cat5) (Typlcally 120m for Cat6, 100m tor

RCP to Boundary Box:

STPIXLR3 Mic cable
Maximum cable length >1km

7
HDStumpCam V3 Operating Manual V0.1
CAT5E 568B WIRING SPECIFICATION

CONNECTOR SHOWN WITH THE

LATCH UNDERSIDE

Camera Corps Ltd.

+44 (0) 1932 336052
Unit 2, 111 Chertsey Road
Byfleet
Surrey
KT14 7AX
United Kingdom