GSO OIML R-121-2007-En
GSO OIML R-121-2007-En
GSO OIML R-121-2007-En
ICS:17.020
FOREWORD
GSO through the technical program of committee TC No.4 " Technical Committee of
Metrology Standards " has adopted the International Standard No. (OIML) R 121:1996
“The scale of relative humidity of air certified against saturated salt solutions " issued by
(International Organization of Legal Metrology ) which has been translated into Arabic.
The Draft Standard has been prepared by (SAUDI ARABIA)
This standard has been approved as Gulf Standard without any technical modifications by
GSO Board of Directors in its meeting No (6) held on 19/5/1428 H , 5/6/2007G
1. OBJECT
The relative humidity scale certified with the help of saturated salt solutions is
used in hygrometry in the relative humidity (RH) fixed points method. It is a
subsidiary scale comprising a number of fixed points reproduced by secondary
standards for humidity measurements.
The RH fixed points represent some specific RH values that are established at a
certain temperature over saturated solutions of salts arising from the hygrostatic
properties of such solutions.
This standard specifies a set of selected saturated salt solutions whose RH
values at a specific temperature correspond to fixed points (or scale marks) of
the scale of relative humidity. Moreover, it indicates the conditions under
which saturated solutions can be used as hygrostatic solutions.
The fixed points method is convenient, inexpensive and reproducible. It is
often used for the calibration and checking of instruments that are generally
used in industry and research laboratories to measure the relative humidity of
air.
The use of hygrostatic solutions has also been described in GSO standard to be
approved by the organization (1) and GSO standard to be approved by the
organization (2) and in national standards [3, 4, 5].
The properties of the solutions and of the water vapor pressure over these
solutions have been the subject of numerous studies in a great number of
laboratories
2. UNITS OF MEASUREMENT
The units of' measurement to be used in calculations shall be those of the SI
system and should conform with the GSO standard to be approved by the
organization (3) “Legal units of measurement”.
2.1 The relative humidity of air as reproduced by hygrostatic solutions shall be
expressed as percentages (%).
2.2 The temperature shall be expressed in degrees Celsius (oC).
2.3 The pressure shall be expressed in hectopascals (hPa).
(1)
It is based on ISO 483 [1]
(2)
It is based on IEC 260 [2]
(3)
It is based on OIML D2
3. DEFINITIONS
3.1 A hygrostatic solution is a saturated solution of specified salt which remains in
thermodynamic equilibrium in the three-phase system at a specific temperature
and pressure.
3.2 The physical quantity reproduced by a hygrostatic solution is the relative
humidify of air over the saturated solution of the salt at given temperature and
pressure.
3.3 The relative humidity Uw, with respect to water in moist air at pressure p and
temperature t, is the ratio (expressed as a percentage) of the vapor mole fraction
of water xv to the vapor mole fraction of water xvw which the air would contain
if it were saturated with respect to water at the same pressure p and
temperature t.
Uw = 100 (xv/xvw)p.t = 100 (e’/e’w)p,t
Where
Indices p and t indicate that each term is subject to identical conditions of
pressure and temperature,
e’ is the vapor pressure of water vapor in moist air,
e’w is the saturation vapor pressure.
5. HYGROSTATIC SOLUTIONS
5.1 The relative humidity scale certified against saturated solutions of salts,
referred to as hygrostatic solutions, is made up of a set of 11 humidity fixed
points (HFP), obtained with the use of saturated solutions of 11 salts. The
numbers given to the HEPs denote the approximate nominal values of relative
humidity at 20oC.
The scale encompasses the relative humidity range from 2% to 98.5% and a
temperature range from 5oC to 80oC.
The scale is made up of the following salts:
HFP 4 Caesium Fluoride CsF temp. from 15 oC to 80 oC
HFP 7 Lithium Bromide LiBr temp. from 5 oC to 80 oC
HFP 12 Lithium Chloride LiCl temp. from 5 oC to 80 oC
HFP 23 Potassium Acetate CH3COOK temp. from 10 oC to 30 oC
HFP 33 Magnesium Chloride MgCl2 temp. from 5 oC to 80 oC
HFP 43 Potassium Carbonate K2 CO3 temp. from 5 oC to 30 oC
HFP 59 Sodium Bromide NaBr temp. from 5 oC to 80 oC
HFP 70 Potassium Iodide KI temp. from 5 oC to 80 oC
HFP 75 Sodium Chloride NaCl temp. from 5 oC to 80 oC
HFP 85 Potassium Chloride KCl temp. from 5 oC to 80 oC
HFP 98 Potassium Sulfate K2SO4 temp. from 5 oC to 50 oC
When the salt solutions that make up the HFP scale are used at temperatures
above 40oC, the risk of salt crystals settling on the surface rather than being
immersed in the solution must be taken into account.
The potassium iodide solution must be free of potassium iodide K103 and must
be stored in a dark place.
5.2 The temperature dependence of relative humidity of air over the saturated salt
solution is presented in Table 1. The HFP values in Table 1 are given every 5oC
for a temperature range of 5oC to 80oC (except for the HFP 98 values known up
to 50oC and HFP 43 and HFP 23 values known up to 30 oC).
Table 1 provides the following data for each saturated salt solution over the
temperature range:
• HFP values, i.e. the relative humidity values over the saturated salt
solutions, at the specified temperature points.
• ∆HFPD values, i.e. the uncertainties with which the HFP values are
known (these values can be considered as equivalent to expanded
uncertainties calculated with k = 2).
Under ideal conditions, the accuracy of the sources generated by this practice is
equal to the uncertainty figures associated with each source value, as stated in
Table 1.
REFERENCES
[1] ISO 483 Plastic Methods for mainaining constant relative humidity in small
enclosures by means of aqueous solutions (1966).
[2] IEC 260 Test enclosures of non-injection type for constant relative humdiity
(1968).
[3] DIN 50008 Konstantklimate uber wasserigen lostungen (1981).
[4] NF X 15-014 Petites enceintes de conditionmement et d’essai utilisant des
solutions aqueuses (1973).
[5] ASTM E 104-85 Standard practice for maintaining constant relative humidity
by means of aquous solutions (reapproved 1991).
[6] Greenspan L., Humidity fixed points of binary saturated aqueous solutions, J.
Res. Nat. Bur. Stand. (U.S.) 81A No. 1 pp. 89-96 (1977).
[7] Arai C., Hosaka S., Murase K., Sano Y., Measurements of the relative humdiity
of saturated aqueous aalt solutions, J. of Chem. Eng. of Japan, Vol. 9. No. 4
(1976).
[8] Acheson D.T., Vapor pressures of saturated aqueous salt solutions, Humidity
and Moisture, Reinhold Publsihing Corp. New York. Vol. 3. pp. 521-530
(1965).
[9] Hedlin C.P., Trofimenkoff F.N. Relative humidities over saturated solutions of
nine salts in the temperature range from 0 to 90 oF, Humidity and Moisture,
Reinhold Publishing Corp. New York, Vol. 3. pp 519-520 (1965).
[10] Vekker B.L., Gershkowits E., Operdelenie otnositel’noi vlazhnosti nad
nasyshchennymi rastvorami ryada solei v diapazone temperature of 0 do 60oC,
Nauchnye pribory SEV. No. (1973)
[11] Wexler A., Hasegawa S., Relative humidity temperature relationships of some
saturated salt solutions in the temperatue range 0oC to 50oC, J. Res. Nat. Bur.
Stand. (U.S.) 53, No 1. pp. 19-26 (1945).
[12] World Meterological Organization, Technical Regulations WMO No. 49, Basic
Document No. 2 (1984).
[13] Young J.F. Humidity control in the laboratory using salt solutions, A. Review,
J. Appl. Chem. Vol. 17 PP. 241-245 (1967).
[14] Hung P.H., Whetstone J.R., Evaluation of relative humidity values for saturated
aqueous salt solutions using osmotic coefficients between 50 and 100oC, and
Moisture and humidity measurement and control in science and industry,
Instrument Society of America. pp. 577-596 (1985).
[15] Stokes R.H., Robinson R.A. Ind. Engug. Chem., Vol. 41, p. 2013 (1949) and
Robinson R.A., Stokes R.H., Electolxtic solutions, 2nd ed. London
Butherworths Scientific Publ. (1959).
[16] Pitzer K.S. Peiper J.C., Busev R.11., Thermodynamic propertics of aqueous
sodium chloride solutions, J. Phys. Chem. Rel. Data, Vol. 13. No. 1. pp. 1-102
(1984).
[17] Cretinon B., Merigous J., Checking of the CETIAT Humiditt transfer standard
with satturated sah salt solution, Industrial Metrology, Vol. 1 pp. 353-358
(1991).
[18] Nelson D.E. Amdur E.J. The made of operation of saturation temperature
hygrometers based on electrical detection of a salt-solution phase transition,
Humidity and Moisture, Reinhold Publishing Corp. New. York. Vol. 1. pp.
617-626 (1965).
[19] IUPAC Recommendation Recommended reference materials for the realization
of physicochemical propertices, Blackwell Scientific Publications (1987).
Table 1
Equilibrium relative humidity values for selected saturated aqueous salt solutions
Relative humidity %
t HFP 4 HFP 7 HFP 12 HFP 23 HFP 33 HFP 43 HFP 59 HFP 70 HFP 75 HFP 85 HFP 98
o
C Caesium Lithium Lithium Potassium Magnesium Potassium Sodium Potassium Sodium Potassium Potassium
Fluoride Bromide Chloride Acetate Chloride Carbonate Bromide Iodide Chloride Chloride Sulfate
(7) (7) (7) (7) (7) (7) (7) (7) (8) (7) (7)
5 – 7.4 ± 0.8 13(3) – 33.6 ± 0.3 43.1 ± 0.5 63.5 ± 0.8 73.3 ± 0.4 75.7 ± 0.3 87.7 ± 0.5 98.5 ± 1.0
(4)
10 – 7.1 ± 0.7 13 23.4 ± 0.6 33.5 ± 0.3 43.1 ± 0.4 62.2 ± 0.6 72.1 ± 0.4 75.7 ± 0.3 86.8 ± 0.4 98.2 ± 0.8
15 4.3(1) ± 1.4(2) 6.9 ± 0.7 12(5) 23.4 ± 0.4 33.3 ± 0.3 43.2 ± 0.4 60.7 ± 0.6 71.0 ± 0.3 75.6 ± 0.2 85.9 ± 0.4 97.9 ± 0.7
20 3.8 ± 1.1 6.6 ± 0.6 12(6) 23.1 ± 0.3 33.1 ± 0.2 43.2 ± 0.4 59.1 ± 0.5 69.9 ± 0.3 75.5 ± 0.2 85.1 ± 0.3 97.6 ± 0.6
25 3.4 ± 1.0 6.4 ± 0.6 11.3 ± 0.3 22.5 ± 0.4 32.8 ± 0.2 43.2 ± 0.4 57.6 ± 0.4 68.9 ± 0.3 75.3 ± 0.2 84.2 ± 0.3 97.3 ± 0.5
30 3.0 ± 0.8 6.2 ± 0.5 11.3 ± 0.3 21.6 ± 0.6 32.4 ± 0.2 43.2 ± 0.5 56.0 ± 0.4 67.9 ± 0.3 75.1 ± 0.2 83.6 ± 0.3 97.0 ± 0.4
35 2.7 ± 0.7 6.0 ± 0.5 11.3 ± 0.3 – 32.1 ± 0.2 – 54.6 ± 0.4 67.0 ± 0.3 74.9 ± 0.2 83.0 ± 0.3 96.7 ± 0.4
40 2.4 ± 0.6 5.8 ± 0.4 11.2 ± 0.3 – 31.6 ± 0.2 – 53.2 ± 0.5 66.1 ± 0.3 74.7 ± 0.2 82.3 ± 0.3 96.4 ± 0.4
45 2.2 ± 0.5 5.7 ± 0.4 11.2 ± 0.3 – 31.1 ± 0.2 – 52.0 ± 0.5 65.3 ± 0.3 74.5 ± 0.2 81.7 ± 0.3 96.1 ± 0.4
50 2.1 ± 0.4 5.5 ± 0.4 11.1 ± 0.3 – 30.5 ± 0.2 – 50.9 ± 0.6 64.5 ± 0.3 74.5 ± 0.9 81.2 ± 0.4 95.8 ± 0.5
55 2.0 ± 0.4 5.4 ± 0.3 11.0 ± 0.3 – 29.9 ± 0.2 – 50.2 ± 0.7 63.8 ± 0.4 74.5 ± 0.9 80.7 ± 0.4 –
60 2.0 ± 0.4 5.3 ± 0.3 11.0 ± 0.3 – 29.3 ± 0.2 – 49.7 ± 0.8 63.1 ± 0.4 74.4 ± 0.9 80.3 ± 0.5 –
65 2.1 ± 0.5 5.3 ± 0.3 10.9 ± 0.3 – 28.5 ± 0.3 – 49.5 ± 1.0 62.5 ± 0.4 74.2 ± 0.9 79.9 ± 0.5 –
70 2.2 ± 0.6 5.2 ± 0.3 10.8 ± 04 – 27.8 ± 0.3 – 49.7 ± 1.1 61.9 ± 0.4 74.1 ± 0.9 79.5 ± 0.6 –
75 2.4 ± 0.7 5.2 ± 0.2 10.6 ± 0.4 – 26.9 ± 0.3 – 50.3 ± 1.3 61.4 ± 0.5 74.0 ± 0.9 79.2 ± 0.7 –
80 2.6 ± 0.8 5.2 ± 0.2 10.5 ± 0.5 – 26.1 ± 0.4 – 51.4 ± 1.5 61.0 ± 0.5 73.9 ± 0.9 78.9 ± 0.8 –
1) HFP : humidity fixed point
2) ∆HFPD : the uncertainties with the HFP values are reported in literature rounded to 0.1 % (these values can be considered as equivalent to expanded
uncertainties calculated with k = 2)
3) Values dispersion from 11.2 % to 14.0%
4) Values dispersion from 11.3 % to 14.3 %
5) Values dispersion from 11.3 % to 13.8 %
6) Values dispersion from 11.1 % to 12.6 %
7) HFP values according to L, Greenspan [6]
8) HFP values according to a) L, Greenspan from 5oC to 45 oC [6]
b) P.H. Huang and J.R. Whetstone from 50oC to 80oC [14]
9
Licensed to OFFICINE MECCANICHE AERONAUTICHE S.p.A. / Alessia Scinocca
Order No. GSO#23.1706 - Order Date 7.3.2023 - Copying and networking prohibited.