Quincy QGD 20-25-30 QGD 40 50 Parts Manual

QGD-20/25/30
& QGD-40/50
Direct Drive Rotary Screw Air Compressor
Parts Manual
This manual contains important safety information and should be made available to
all personnel who operate and/or maintain this product. Carefully read this manual
before attempting to operate or perform maintenance on this equipment.
Manual No. 65112-1A
May 2009 Edition

Alphabetical Index
Airend (50 hp, 100/125#)................................................................................................. 8-9

Airend(s) (20/25/30 hp)..................................................................................................... 4-5
Airend(s) (40 hp/50 hp, 150#) . ........................................................................................ 6-7
Air Filter ....................................................................................................................... 20-21
Air Piping (20/25/30 hp) .............................................................................................. 44-45
Air Piping (40/50 hp) ................................................................................................... 46-47
Cabinet (20/25/30 hp) ................................................................................................. 62-63
Cabinet (40/50 hp) ...................................................................................................... 64-65
Control Piping (20/25/30 hp)........................................................................................ 28-39
Control Piping (40/50 hp) ............................................................................................ 40-43
Control Schematics...................................................................................................... 68-75
Cooler (20/25/30 hp) ................................................................................................... 58-59
Cooler (40/50 hp) ........................................................................................................ 60-61
Decals .......................................................................................................................... 66-67
Drive Coupling ............................................................................................................ 10-11
Electrical Control & Starting (gauge control)................................................................ 22-27
Electrical Control Diagram (full voltage, auto dual)...................................................... 76-79
Fluid Piping (20/25/30 hp) . ......................................................................................... 50-51
Fluid Piping (40/50 hp) ................................................................................................ 52-53
Fluid Specifications...............................................................................................................2
Inlet Valves .................................................................................................................. 14-19
Motor Mounting (20/25/30 hp) .........................................................................................12
Motor Mounting (40/50 hp) . .............................................................................................13
Ordering Replacement Parts................................................................................................1
Receiver (20/25/30 hp) ................................................................................................ 48-49
Recommended Spare Parts..................................................................................................3
Reservoir (20/25/30 hp) ............................................................................................... 54-55
Reservoir (40/50 hp) .................................................................................................... 56-57
Serial Number Identification.................................................................................................1
Shaft Seal Kit ................................................................................................................ 4/6/8
Book Update: 05/01/09

All groups and part numbers verified and updated.
Added 50 hp data & receiver option.
Quincy Compressor® - QGD

Serial Number Identification
The serial number tag is located on the top flange of the unit frame just left of the
control panel and in the upper right corner of the electrical control panel.
Ordering Replacement Parts

Prompt service can be rendered on replacement part orders if the following information
is given:
1. The serial number must be given when ordering replacement parts. Part
numbers should be verified per the bill of materials associated with the serial
number to ensure that correct replacement parts are ordered.
2. State the exact part number needed. Do not order by index numbers, as
index numbers are repeated throughout this manual and if used for ordering
parts will necessitate time consuming correspondence.
3. State the exact quantity needed.
4. State the preferred type of transportation.
All replacement parts are to be ordered through an authorized distributor. Insist on
Genuine Quincy Parts only! Failure to do so may void your warranty.

Fluid Specifications
Quincy Compressor® recommends that all Quincy Rotary Screw Products be filled with
one of the following QuinSyn® Brand synthetic fluids:
HQuinSyn Plus™H HQuinSyn XP®H
HQuinSyn PG™H HQuinSyn F® (food grade)H

Synthetic fluids other than QuinSyn brand(s) may not be compatible with components
used in Quincy Compressor products. If it is deemed necessary to convert a Quincy
compressor or vacuum pump to a synthetic other than QuinSyn brand, please contact an
authorized Quincy Compressor distributor. To locate your nearest distributor, contact
Sales & Marketing in Quincy, Illinois:
Phone 217-222-7700, FAX 217-222-4138 or visit our website:
http://www.quincycompressor.com.
The following information will be required by the distributor when changing compressor
fluid:
Horsepower Cooling PSI
QGD 20 25 30 40 A/C 100 125
Model (circle configuration):_______________________________________________________________________
Serial No.______________________________________ Fluid Originally Used:_ ____________________________
Fluid Now Used (if changed):_ _____________________ New Fluid To Be Used:_____________________________
Additional information regarding fluid specifications can be found in the Instruction

Manual shipped with your unit.
• Fluid Analysis Kit

Quincy Compressor offers free fluid analysis to provide early detection of excessive parts
wear, fluid breakdown, or a contaminated fluid system. Order the Fluid Analysis Kit (part
no. 128515) from your local authorized Quincy Compressor distributor.
• Fluid Requirements
20, 25 & 30hp - 3.00 gallons
40 hp - 7.50 gallons

Recommended Spare Parts
Qty. Part Number Description
1 140209 shaft seal kit
1 128849E362 air filter element
1 122880-232 temperature switch (230°f) (gauge control)
1 144981 temperature probe-high vibration, 0.50 npt
(microprocessor control)
1 129732-051 line filter kit (includes bowl seal, filter element, gasket)
1 146175-100 differential pilot valve kit
(includes diaphragm assembly & seat)
1 146914 air/fluid separator element
1 147564k minimum pressure check valve kit (20/25/30 hp)
1 147565k minimum pressure check valve kit (40/50 hp)
1 128598 fluid filter element
2 144046-005 fluid-Quinsyn Plus (5 gallon container)
2 143808-005 fluid-Quinsyn PG (5 gallon container)
2 142784-005 fluid-Quinsyn XP (5 gallon container)
2 110756-005 fluid-Quinsyn F (5 gallon container)
1 128515-3 fluid analysis kit (contains 3 individual sample kits)
Warning Danger
Guards must be fastened in place before Air in the piping from this equipment will cause
starting the machine and never removed severe injury or death if used for breathing
before disconnecting and locking out the air or food processing(If non-food grade
main power supply. fluid is used).
Air used for these processes
must meet OSHA 29CFR1910.134 or FDA
21CFR178.3570 standards.

Airend(s) (20/25/30 hp)
147325-TEC
1
3
2
5
4
6
41
37
30
29
13
40
18
20
38
39
NOTES - UNLESS OTHERWISE SPECIFIED:

1) ONLY EXTERNAL, REPLACEABLE ITEMS ARE SHOWN.
INTERNAL AIREND COMPONENTS ARE NOT SHOWN.
2) NOT ALL REPLACEABLE ITEMS ARE SHOWN.
Shaft Seal Kit - 140209

Item No. Qty. Part Number Description
1 1 129613 compressor
fluid slinger
2 1 129612 shaft seal
3 1 129610 wear ring seal
Reference Instruction Manual to install compressor

shaft seal. Tool Kit 140284 for shaft seal and wear ring
installation can be purchased from Quincy Compressor.

Airend(s) (20/25/30 hp)
1 1 129613 compressor fluid slinger
2 1 129466 seal adapter
3 4 90386-J15 counterbore screw-1/4-20 unc x 1.50,
grade 8 (@ 9 ft-lbs)
5 1 22749-154 Viton o-ring-3.75 i.d.
7 * 124232-005 rotor bearing
8 * 147323 rotor housing
9 * 147344-1 male rotor-120 mm
10 * 147345-1 female rotor-101 mm
11 1 146895-2 discharge end plate
1 146895-1 discharge end plate (30 hp, 100 & 125 psi)
12 2 124145-009 dowel pin
13 12 90386-L15 counterbore screw-3/8-16 unc x 1.50,
grade 8 (@ 45 ft-lbs, back off to 25 ft-lbs)
15 1 125688 bearing retainer
18 1 141973-08 spring
19 ** 146838 discharge cap shim-tempered steel
20 1 22749-151 Viton o-ring-3.00 i.d.
21 1 146834 discharge end cap
22 1 146836-1 bearing retainer
23 2 141747-N15 counterbore screw-1/2-20 unf x 1.50,
24 ** 146617 rotor shim-tempered steel
26 1 146836-2 bearing retainer
29 1 22749-140 Viton o-ring-2.25 i.d.
30 1 141973-09 spring
33 1 22749-169 Viton o-ring-7.50 i.d.
34 2 140675-004 Viton o-ring/face seal-0.61 i.d.
35 1 129964-150 internal retaining ring
37 1 128967-001 45° male elbow-0.25 tube x 0.12 npt
38 4 90386-N16 counterbore screw-1/2-13 unc x 1.75,
39 1 147111 fluid gallery cover plate
40 1 22749-163 Viton o-ring-6.00 i.d.
41 2 128883-075 pipe plug-3/4-16 (o-ring)
Component Maintenance Parts
a 2 140406-908 Viton o-ring-0.64 i.d.
* Items not sold separately, must be ordered as a complete airend.

** Quantity as required.
@ Indicates torque value in foot pounds (lubricated threads).

Airend(s) (40 hp/50 hp, 150#) - 146842-003/-103/-004
146842-Tc3
25
22
26
23
24
27
30 20 C
31
18 A
20 C
16
20 C
28
C 20
C 20 A 18
B 19
NOTES - UNLESS OTHERWISE SPECIFIED:

1) ONLY EXTERNAL REPLACEABLE ITEMS ARE SHOWN. 17
INTERNAL AIREND COMPONENTS ARE NOT SHOWN. 20 C
2) NOT ALL REPLACEABLE ITEMS ARE SHOWN.

fluid slinger


Airend(s) (40 hp/50 hp, 150#) - 146842-003/-103/-004
1 * 146844-1 rotor housing
2 2 124145-004 dowel pin
4 1 129964-003 bearing retainer ring
7 * 129611 male rotor-127 mm
8 * 142087 female rotor-127 mm
9 1 125577-001 discharge plate gasket
10 * 146846 discharge end housing
12 * 125580-001 rotor bearing-discharge end
14 6 123478-K12 cap screw-5/16-18 unc x 1.00,
16 2 22749-151 Viton o-ring-3.00 i.d.
17 8 123478-J12 cap screw-1/4-20 unc x 1.00, grade 5 (@ 6 ft-lbs)
18 2 128883-044 pipe plug-7/16-20 (o-ring)
19 1 128883-075 pipe plug-3/4-16 (o-ring)
20 11 128883-038 pipe plug-3/8-24 (o-ring)
21 1 143019 air seal
24 1 22749-242 Viton o-ring-4.00 i.d.
26 4 90386-K12 counterbore screw-5/16-18 unc x 1.00,
30 1 121032-6 pipe nipple-brass, 0.12 npt x 2.5
31 1 125780-002 90° female elbow-0.25 tube X 0.12 npt
A 2 140406-904 Viton o-ring-0.35 i.d.

B 1 140406-908 Viton o-ring-0.64 i.d.
C 11 140406-903 Viton o-ring-0.30 i.d.


Airend (50 hp, 100/125#) - 147250-001
146842-Tc3
3
1
2
4
6
5
38
42 A
42 A
30
29
28
22
41
20
19
40
21
NOTES-UNLESS OTHERWISE SPECIFIED:
1) ONLY SOME REPLACEABLE ITEMS ARE SHOWN.
NOT ALL REPLACEABLE ITEMS ARE SHOWN.
INTERNAL COMPONENTS ARE NOT SHOWN. 39
2) ITEM A IS A MAINTENANCE PART.

fluid slinger


Airend (50 hp, 100/125#) - 147250-001
3 4 90386-J15 counterbore screw-1/4-20 unc x 1.50,
5 1 22749-154 Viton o-ring-3.75 i.d.
8 * 147251 rotor housing
9 * 146806-01 male rotor-143 mm
10 * 146807 female rotor-143 mm
11 1 147214 discharge end plate
12 2 124145-004 dowel pin
14 1 124232-029 rotor bearing
18 1 141973-07 spring
20 1 22749-240 Viton o-ring-3.75 i.d.
24 6 141747-K12 counterbore screw-5/16-24 unf x 1.00,
25 ** 146726 bearing adjustment shim-tempered steel
26 ** 147591 bearing adjustment shim-tempered steel
30 1 22749-233 Viton o-ring-2.88 i.d.
31 1 141973-08 spring
34 1 22749-268 Viton o-ring-8.50 i.d.
35 2 140675-005 Viton o-ring/face seal-0.74 i.d.
38 1 124393-004 male connector-0.25 tube x 0.12 npt
40 1 147111 fluid gallery cover plate
41 1 22749-163 Viton o-ring-6.00 i.d.
42 2 128883-075 pipe plug-3/4-16 (o-ring)
a 2 140406-908 Viton o-ring-0.64 i.d.


Drive Coupling - 146902-001/-002/-003/-004
A 2
1
C
MOTOR SIDE
D AIREND SIDE
B
10 Quincy Compressor® - QGD

Drive Coupling - 146902-001/-002/-003/-004
1 1 128387-100 drive coupling (20,25 & 30 hp)
1 128387-125 drive coupling (40 hp, ODP)
1 128387-154 drive coupling (40 hp, TEFC/50 hp)
2 2 146820 coupling guard (20,25 & 30 hp/50 hp, 100/125#)
2 146804 coupling guard (40 hp/50 hp, 150#)
(20,25 & 30 hp)
4 123478-J07 cap screw-1/4-20 unc x 0.50, grade 5 (@ 6 ft-lbs)
(40 & 50 hp)
4 1 20109 shaft key

20/25/30 hp:
A 1 128387-400 drive coupling element
(1 pair of halves sold as a matched set only)
B 1 128387-300 coupling hub-airend side (includes set screw)
C 1 128387-200 coupling hub-motor side (includes set screw)
D 1 128387-500 drive coupling bolt kit (@ 22 ft-lbs, dry threads)
40/50 hp:
A 1 128387-412 drive coupling element
(1 pair of halves sold as a matched set only)
B 1 128387-301 coupling hub-airend side (includes set screw)
C 1 128387-219 coupling hub-motor side (includes set screw)
(40 hp, ODP)
1 128387-203 coupling hub-motor side (includes set screw)
(40 hp, TEFC/50 hp)
D 1 128387-501 drive coupling bolt kit (@ 22 ft-lbs, dry threads)
Quincy Compressor® - QGD 11

Motor Mounting (20/25/30 hp) - 146904-001/-002
1
4
3
11
9
9
10

1) ITEMS 3 & 4 ARE USED TO ATTACH DRIVE MOTOR TO AIREND HOUSING.
2) SHIPPING SUPPORTS (ITEM 10) ARE TO BE REMOVED AFTER INSTALLATION.

1 1 147334-02 motor support (20 hp)
1 147334-01 motor support (25 & 30 hp)
2 2 142201-02 motor mount
3 4 142578-N15 cap screw-zinc, 1/2-13 unc x 1.50,
4 4 123115-08Z lockwasher-zinc, 0.50
6 2 124370-N02 locknut-1/2-13 unc
7 6 129303R050 fender washer
8 2 110428W050 flat washer-0.50
9 6 14654408020 lock screw-zinc, 8 mm x 20 mm
10 2 146942-01 shipping support
11 2 141631-N10 cap screw-1/2-13 unc x 0.75, grade 5 (@ 23 ft-lbs)

Motor Mounting (40/50 hp) - 146937-001/-002/-003
6
13
7 (NOTE 2)
2
1 4
3
10 11
12
7
(NOTES 3 & 4)

1) ITEMS 3 & 4 ARE USED TO ATTACH DRIVE MOTOR TO AIREND HOUSING.
2) ITEM 7 NOT USED IN THIS LOCATION ON 40 HP UNITS WITH ODP MOTORS
(UNITS WITH SPACERS).
3) SHIPPING SUPPORT(S) (ITEM 10) TO BE REMOVED AFTER UNIT INSTALLATION.
4) 50 HP, 100 & 125# UNITS USE TWO (2) SUPPORTS, ALL 40 HP UNITS &
50 HP, 150# UNITS USE ONE (1).
4) ITEM 13 (SPACER) USED ONLY ON 40 HP UNITS WITH ODP MOTORS.

1 1 147334-04 motor support (all 40 hp/50 hp 150#)
1 147334-03 motor support (50 hp, 100/125#)
grade 5 (@ 23 ft-lbs) (all 40 hp/50 hp 150#)
4 142578-Q15 cap screw-zinc, 5/8-11 unc x 1.50,
grade 5 (@ 110 ft-lbs) (50 hp, 100/125#)
4 4 123115-08Z lockwasher-zinc, 0.50 (all 40 hp/50 hp 150#)
4 123115-10Z lockwasher-zinc, 0.63 (50 hp, 100/125#)
5 2 142578-N21 cap screw-zinc, 1/2-13 unc x 3.00, grade 5 (@ 23 ft-lbs) (TEFC)
2 142578-N25 cap screw-zinc, 1/2-13 unc x 4.00, grade 5 (@ 23 ft-lbs) (ODP)
6 2 124370-N02 locknut-1/2-13 unc
7 * 129303R050 fender washer
8 2 110428W050 flat washer-0.50
10 1 146942-02 shipping support (all 40 hp/50 hp 150#)
2 146942-03 shipping support (50 hp, 100/125#)
11 * 141631-N10 cap screw-1/2-13 unc x 0.75, grade 5 (@ 23 ft-lbs)
4 14654412030 lock screw-zinc, 12 mm x 30 mm
13 2 129059-3 motor spacer (40 HP,ODP only)
* Quantity varies. Reference drawing notes.

Inlet Valve (20/25/30* hp) - 128900-006/-007
17 15
16
8
14
13
12
11
19
10
25 8
7
6
5
9
2
23
24
3
18
22
1 21
20

1) APPLY LOCTITE 271 TO ITEM 12 AT ASSEMBLY WITH ITEM 13.
2) COAT PRESSURE SIDE OF ITEM 14 WITH E4 (MOLYDISULF) POWDER.
3) ITEM 25 (SPACER) NOT USED ON 25 HP UNITS.
4) COAT ENTIRE OUTSIDE WALL OF SLEEVE (ITEM 19) WITH LOCTITE 609.
5) APPLY TEFLON LUBRICANT TO SEAL (ITEM 14) PRIOR TO INSTALLATION IN CYLINDER.
6) MAKE SURE FLAT PORTION OF SEAL (ITEM 14) IS FACING AWAY FROM CYLINDER.

Inlet Valve (20/25/30* hp) - 128900-006/-007
1 1 128861 inlet valve gasket
2 1 128805 inlet valve housing
4 4 123115-04C lockwasher, 0.25
5 1 124098-013 retaining ring
6 1 128853 inlet valve plate
7 1 128963 compression spring
8 2 123549-006 gasket-4.31 o.d. x 3.06 i.d.
9 1 128560 inlet valve shaft seal
10 1 128806-1 inlet valve cylinder assembly
11 1 128994 compression spring
12 1 128852 inlet valve shaft
13 1 128854-1 inlet valve piston
14 1 147439 piston seal
15 1 128807 inlet valve cylinder cap
16 6 123115-05C lockwasher, 0.31
17 6 123478-K15 cap screw-5/16-18 unc x 1.50,
18 1 142125-15 extra strong brass nipple-0.12 npt x 1.25
19 1 127483-1 cylinder sleeve
20 1 122212 pipe elbow-brass, 0.125 npt x 0.25 npt
21 1 147235-025 in-line check valve, 200#
23 0.6 140620-003 black nylon tubing-0.25 o.d.
25 1 128995 inlet valve shaft spacer (20 hp only)
* This inlet valve configuration used on 30 hp units only at 150 psig.


Inlet Valve (30 hp, full voltage) - 146952
17
16
15
14 5
6
13
7
12
8
11
9
18
10
3
2 21
19
20
22

Inlet Valve (30 hp, full voltage) - 146952
2 1 143127 inlet valve housing assembly
5 1 143128 inlet valve plate assembly
6 1 125912 valve disc-bypass
7 1 2134 valve gasket
8 1 123092 spring
9 1 123157-012 Buna-N o-ring-0.38 i.d.
10 1 127203 valve plate retainer
11 1 127201 inlet valve spacer
12 1 126460-200 piston cup
13 1 124370-L02 locknut-3/8-16 unc
14 1 126461 inlet valve spring
15 1 126358 inlet valve cylinder cap
18 1 126796 inlet valve shaft seal
20 1 146989 inlet valve adapter
22 1 22749-155 Viton o-ring-4.00 i.d.

Inlet Valve (30 hp, wye-delta) - 147587 / (40/50 hp) - 126650
20
17
14 13
16 12
15 11
10
7 4
2
19
6
1
21
22
NOTE-UNLESS OTHERWISE SPECIFIED: 23

1) APPLY LOCTITE 609 TO ITEM 15 AT ASSEMBLY WITH ITEM 11.

Inlet Valve (30 hp, wye-delta) - 147587 / (40/50 hp) - 126650
3 1 126646 inlet valve housing
4 1 122995 inlet valve plate assembly
5 1 124368-N02Z jam nut-1/2-13 unc, zinc
6 1 128720-001 hex head screw-1/2-13 unc X 5.00,
7 1 123092 spring
8 1 123549-003 gasket-6.50 o.d. x 4.56 i.d.
9 1 126644 inlet valve cylinder (includes bushing-p/n 22880)
10 1 126649 inlet valve spring
12 1 126647 flat washer-0.56
13 1 126460-350 piston cup
14 1 1478-1 flat washer-0.52
16 1 126645 inlet valve cover plate
17 6 123478-L15 cap screw-3/8-16 unc x 1.50, grade 5 (@ 23 ft-lbs)
19 5 123115-08C lockwasher, 0.50
20 6 123115-06C lockwasher, 0.38
21* 4 90386-L14 counterbore screw-3/8-16 unc x 1.25,
22* 1 146989 inlet valve adapter
23* 1 22749-155 Viton o-ring-4.00 i.d.
* Items 21, 22 & 23 used only on 30 hp, wye-delta units.


Air Filter - 146903-001 thru -008
3
5
7
9
10
1

1) ITEM 4 (VIBRATION DAMPENER) IS NOT SHOWN.
2) ITEMS 9 & 10 (HOSE AND HOSE CLAMP) ARE USED
ONLY ON UNITS W/CABINET.

Air Filter - 146903-001 thru -008
1 1 146929-03 air filter housing top
(QGD-20/25 & 30, full voltage)
1 146960 air filter housing ASSEMBLY (QGD-30, wye-delta)
1 146929-01 air filter housing ASSEMBLY (QGD-40/50)
2 1 128849E362 air filter element (QGD-20/25/30)
1 125420E200 air filter element (QGD-40/50)
3 1 128882 wing nut-1/4-20 unc
4 2.7 20579 vibration dampener
5 1 113956-002 sealing washer
6* 1 146956 air filter gasket (QGD-20/25)
1 146957 air filter gasket (QGD-30, full voltage)
7* 1 127635-002 threaded rod, 0.25 x 9.38 (QGD-20/25)
1 127635-009 threaded rod, 0.25 x 7.00 (QGD-30, full voltage)
8* 1 146929-04 air filter housing bottom (QGD-20/25)
1 146929-05 air filter housing bottom (QGD-30, full voltage)
9 1 146958-54 intake air hose-3.5 id x 54.00
(QGD-20/25/30, w/cabinet)
1 123072-90 intake air hose-4.0 id x 90.00
(QGD-40/50, w/cabinet)
10 2 110423-056 hose clamp (QGD-20/25/30, w/cabinet)
2 110423-072 hose clamp (QGD-40/50, w/cabinet)
* Items 6, 7 & 8 are not used on QGD-30, wye-delta or QGD 40/50.

Electrical Control & Starting (gauge control)
pix5120
1
13
16
3
7 5
14
4
6
21 20 19 26
WYE-DELTA
OVERLOAD
LOCATION
25 22
WYE-DELTA
24 CONTACTOR
23
15

Electrical Control & Starting (gauge control)
1 Start Button
Requires: 1 146102L001 illuminated green button-momentary
1 143144-03 green lamp
1 146103-006 lamp base contact
2 146103-001 contact block (normally open)
2 1 146102-006 emergency stop button
Requires: 1 146103-002 contact block (normally closed)
3 HAT indicator
Requires: 1 146102-012 red indicator lense
1 143144-02 red lamp
1 146103-006 lamp base contact
1 146103-007 contact base adapter
4 1 146551-50 hourmeter (50 Hz)
1 146551-60 hourmeter (60 Hz)
5 2 147135-01 relay assembly
6 1 142334-26 terminal block assembly
7 1 146459 HMI bezel
8* 1 122880-232 temperature switch (230°f)
9 1 129229-005 power block
10* 1 143470 electrical decals sheet
11* 1 113058 control panel decal-UL listed
12* 10 146302-218 shielded cable
13 1 147311-1 decal-auto dual
1 147311-2 decal-auto demand
1 147311-3 decal-lead/lag
14 *** 144739 programmable timer
15 2 128002-001 ground terminal
16 1 146102-007 two position selector switch
Includes: 1 146103-002 contact block (normally closed)
** 1 146103-001 contact block (normally open)
17* 1 129229-006 power block (wye-delta)
18* 1 129229-009 power block (40/50 hp, wye-delta, 200/230 volt only)
19 (page 22) transformer
20 (page 22) transformer fuse (primary)
21 1 128622-250 transformer fuse (secondary) (20/25/30 hp)
1 128622-400 transformer fuse (secondary) (40/50 hp)
22 (page 22) drive motor contactor
23 (page 23) drive motor overload relay
24 1 144570-01 FAN MOTOR contactor-120 volt
25 1 (page 23) FAN MOTOR overload disconnect
Phase Monitor Option:

26 1 147319 phase monitor (200-690 volt)
3 128858-010 fuse
1 144117-06 fuseblock
Auto Restart Option (not shown):

2 144739 programmable timer
2 147135-01 relay assembly
* Not shown.
** Used on auto demand and lead/lag units only.
*** Quantity of 1 on full voltage units, 2 on wye-delta units.

Electrical Control & Starting (microprocessor control)
pix5121
2
5
6 23
7 1 3
28
17
20 19 18
9
22 21
WYE-DELTA
OVERLOAD
LOCATION
27
24
26
WYE-DELTA
CONTACTOR
25

Electrical Control & Starting (microprocessor control)
1 1 146303-102 PLC controller
2 1 146303-202 operator interface
3 1 146303-504 chip-battery backup
4 1 146457 control panel decal
5 1 146459 HMI bezel
6 1 146102-006 emergency stop button
Requires:
2 146103-002 contact block (normally closed)
7 1 142334-26 terminal block assembly
8 3 128002-001 ground terminal
9 1 129229-005 power block
10* 1 129229-006 power block (wye-delta, 20/25/30 hp)
1 129229-007 power block (wye-delta, 40/50 hp)
11* 1 143470 electrical decals sheet
12* 1 144981 temperature probe-high vibration, 0.50 npt
13* 1 145072 pressure transducer (0-300#)
14* 1 145072C07 cable assembly-80 inch
15* 8 146302-218 shielded cable
16* 1 113058 control panel decal-UL listed
17 1 145785-250 transformer (250va) (20/25/30 hp)
1 145785-350 transformer (350va) (40/50 hp)
18 1 144117-06 fuseblock
19 (page 22) transformer fuse (primary)
20 1 128857-005 transformer fuse (secondary) (20/25/30 hp)
1 128857-007 transformer fuse (secondary) (40/50 hp)
21 1 144117-04 fuseblock
22 1 128857-009 fuse (6 amp)
23 1 146551-60 hourmeter (60 Hz)
1 146551-50 hourmeter (50 Hz)
24 1 (page 22) drive motor contactor
25 1 (page 23) drive motor overload relay
26 1 144570-01 FAN MOTOR contactor-120 volt
27 1 (page 23) FAN MOTOR overload disconnect
Phase Monitor Option:

28 1 147319 phase monitor (200-690 volt)
3 128858-010 fuse
1 144117-06 fuseblock
* Not shown.

Electrical Control & Starting
Transformer
Gauge Control
Voltage Qty. 20/25/30 hp 40/50 hp
200 1 128413-251 128413-351
230 1 128413-253 128413-353
380 1 128413-256 128413-356
415 1 128413-254 128413-354
460 1 128413-253 128413-353
575 1 128413-255 128413-355
Transformer Fuses (Primary)

200 2 128857-012 128857-006
230 2 128857-015 128857-005
380 2 128857-011 128857-004
415 2 128857-011 128857-004
460 2 128857-011 128857-030
575 2 128857-003 128857-011
Drive Motor Contactor

Full Voltage
Voltage Qty. 20 hp 25 hp 30 hp 40 hp 50 hp
200 1 144570-09 144570-10 144570-12 144570-13 144570-13
230 1 144570-09 144570-10 144570-11 144570-12 144570-13
380 1 144570-06 144570-07 144570-08 144570-09 144570-10
415 1 144570-06 144570-06 144570-08 144570-09 144570-10
460 1 144570-06 144570-07 144570-09 144570-09 144570-09
575 1 144570-05 144570-06 144570-07 144570-08 144570-08
Wye-Delta
200 * 144570-07 (1) 144570-08 (2) 144570-09 (1) 144570-10 (1) 144570-11 (2)
* 144570-05 (1) 144570-08 (1) 144570-08 (1)
230 * 144570-07 (1) 144570-08 (2) 144570-08 (2) 144570-09 (1) 144570-10 (1)
* 144570-05 (1) 144570-08 (1) 144570-08 (1)
380 * 144570-04 (1) 144570-04 (1) 144570-05 (2) 144570-09 (1) 144570-08 (2)
* 144570-02 (1) 144570-03 (1) 144570-08 (1)
415 * 144570-03 (1) 144570-04 (1) 144570-05 (2) 144570-06 (1) 144570-07 (1)
* 144570-01 (1) 144570-02 (1) 144570-05 (1) 144570-05 (1)
460 * 144570-04 (1) 144570-05 (2) 144570-06 (1) 144570-07 (1) 144570-07 (1)
* 144570-03 (1) 144570-05 (1) 144570-05 (1) 144570-05 (1)
575 * 144570-03 (1) 144570-04 (1) 144570-05 (2) 144570-06 (1) 144570-06 (1)
* 144570-02 (1) 144570-03 (1) 144570-05 (1) 144570-05 (1)
* Quantity is in parenthesis () following part number.

Electrical Control & Starting
Drive Motor Overload Relay
Full Voltage
200 1 143780-06 143780-07 143780-08 143780-09 143780-01
200 1 143780-06 143780-07 143780-07 143780-08 143780-09
380 1 143780-04 143780-05 143780-05 143780-06 143780-06
415 1 143780-04 143780-04 143780-05 143780-06 143780-06
460 1 143780-04 143780-04 143780-05 143780-06 143780-06
575 1 143780-03 143780-04 143780-04 143780-05 143780-05
Wye-Delta
200 1 143780-04 143780-05 143780-06 143780-06 143780-08
230 1 143780-04 143780-05 143780-05 143780-06 143780-07
380 1 143780-14 143780-03 143780-03 143780-04 143780-05
415 1 143780-14 143780-03 143780-03 143780-04 143780-05
460 1 143780-03 143780-03 143780-03 143780-04 143780-05
575 1 143780-14 143780-03 143780-03 143780-04 143780-04
Fan Motor Overload Disconnect

200 1 146237-21 146237-23
230 1 146237-20 146237-22
380 1 146237-21 146237-21
415 1 146237-20 146237-20
460 1 146237-17 146237-19
575 1 146237-16 146237-18

Control Piping (20/25 hp, gauge) - 147314-001 thru -004
43 42 41 33 3
40
33 3 SEE DETAIL
44 FOR LEAD/LAG
33
39
1 25
3
38
1 3
32 20
3 24 1
37 23 C
2 27
31 2
SEE
AIREND
GROUP 12 1
C 23
36
22
D 28 16 27
1
1 3
3
13 29
P
9
O
I
45 25
27 46 14 B
18 1 8 5 30 E
15
3 1
1 27
20
3
1 10
4
3
2
1 1
12
19
1 26
20
2 18 17 2 2
11 2
12
1
A 7
12 4
3
14 20
3
3
44 44
1
1 6
1 34
3 47 25 1 35
LEAD/LAG DETAIL
SAMPLE
3 PORT
21

2 7 142125-1 extra strong brass nipple-0.25 npt x close
3 30 140620-003 black nylon tubing-0.25 o.d.
4 2 147239-025 shuttle valve-0.25 npt
6 1 125025 line filter orifice (Ø0.040)
7 1 21969-2 differential pilot valve
8 1 140508 sightglass (o-ring)
9 1 128826 blowdown valve
10 1 120496-4 solenoid valve-3-way
11 1 6150 pipe cross-brass, 0.25 npt
12 4 7361 pipe tee-brass, 0.25 npt
13 1 111098-002 pipe nipple-brass, 0.125 npt x 0.25 npt x close
17 1 140533-1 piping support bracket
18 2 129203-003 bulkhead coupling-brass, 0.25 npt
19 1 126345 pressure gauge-liquid filled (0-200#)
21 1 142947 fluid sample valve
23 2 122056 check valve
24 1 140317 rubber grommet
26 2 140764-L05 pan head cap screw-10 unf x 0.38
27 4 122636 pipe elbow-brass, 0.25 npt
28 1 129732 automatic line filter
29 1 7361-001 pipe tee-brass, 0.12 npt
30 1 140106-024 adapter-7/16-20 x 0.25 nptf (o-ring)
31 1 125259-002 pipe coupling-brass, 0.25 x 0.25
33 3 124347-003 connector-0.25 tube x 0.125 npt
34 1 124335-006 pipe plug-galvanized, 0.25 npt
35 1 121033-1 pipe bushing-brass, 0.25 npt x 0.125 npt
36 1 128664-3 temperature gauge assembly
37 1 128663 percent capacity gauge
38 1 128662 pressure gauge (0-300#)
39 1 147464 differential pressure gauge-air filter
40 1 147465 differential pressure gauge-separator
41 1 147466 gauge panel decal
42 1 147514-14 gauge panel
43 4 12798508012 cap screw-zinc, 8 mm x 12 mm
44* 1 22454-1 pressure switch (70-125#)
1 8698-011 pressure switch (150-210#)
46 1 129251-025 plug valve
47 1 20201 tee-0.25 tube x 0.12 npt x 0.12 npt (lead/lag only)
a 1 20775 differential pilot valve kit (includes diaphragm,

diaphragm gaskets, seat gasket, seat disk, seat ring)
b 2 22749-010 Viton o-ring-0.25 i.d.
c 4 123157-008 Buna-N o-ring-0.18 i.d.
d 1 129732-051 line filter kit (includes bowl seal, filter element, gasket)
e 1 140406-904 Viton o-ring-0.35 i.d.
* Quantity of two on units with lead/lag control option.

Reference drawing.

Control Piping (20/25 hp, microprocessor) - 147315-001
SEE
AIREND
GROUP 3
D 28 16 27 24
23 C
1
1 1 2
3
13 22
P
9 25
O
I
3
27 11 14 B
18 1 8 5 30 E
15
3 1
1 27
20
3
10
4
1 1
12
1 26
2 18 17 2 2
12 2 19
1
A 7
12 4
3
14 20
(NOTE 2)
3
F
36
1 6
1 29
1 31
SAMPLE
3 PORT
21

1) ITEM 32 (CABLE ASSEMBLY) IS NOT SHOWN.
2) ITEM 36 LOCATED ON BACK SIDE OF RESERVOIR.

11 1 129251-025 plug valve
32 1 146296 cable assembly-5 meter
33 1 128883-075 pipe plug-3/4-16 (o-ring)


b 2 22749-010 Viton o-ring-0.25 i.d.
c 2 123157-008 Buna-N o-ring-0.18 i.d.
e 1 140406-904 Viton o-ring-0.35 i.d.
f 1 140406-908 Viton o-ring-0.64 i.d.

Control Piping (30 hp, gauge, full voltage) - 147314-005 thru -008
43 42 41 33 3
40
33 3 SEE DETAIL
13 FOR LEAD/LAG
33
39
3
1 25 3
38
1 3
32 20
37 23 C
31 2
SEE
AIREND
GROUP
36
3
UPPER PORT
LOWER PORT UPPER PORT
LOWER PORT
13 13 E 30
22 24 12 2 1
27
31
3 48 25 5 46
27
B 8 47
LEAD/LAG DETAIL
29
20 1 23 C
25 1
44
O 45 44
28 D
27
I P 1
3
16 9 18
3
3 1 1
14
20 3 1
15 3
2 10
1 1
1
12
2 2 2
11
19
1 20
A 7
2 18 12 12
4
17 26 3
14 20
3 3 3
1
1 6
34
1
1
35
SAMPLE
3 PORT
21

Control Piping (30 hp, gauge, full voltage) - 147314-005 thru -008
13* 1 22454-1 pressure switch (70-125#)
1 8698-011 pressure switch (150-210#)
16 1 129251-025 plug valve
38 1 128662 pressure gauge (0-300#)
42 1 147514-14 gauge panel

b 2 22749-010 Viton o-ring-0.25 i.d.
c 2 123157-008 Buna-N o-ring-0.18 i.d.
e 1 140406-904 Viton o-ring-0.35 i.d.
* Quantity of two on units with lead/lag control option. Reference drawing.

Control Piping (30 hp, gauge, wye-delta) - 147314-009 thru -012
43 42 41 33 3
40
33 3 SEE DETAIL
35 FOR LEAD/LAG
33
39
1 30
3
38
1 3
32 20
3
37 23 C 3
31 2 24
SEE
AIREND C 23 1
GROUP
C 30
36 2
28 16 UPPER LOWER
PORT PORT
1 30
30
3 22
3
29
18 3
25
1 30 B
44
3 3
20 8 5 45 E
P O
3 1
16 27
9
I
20
27 1 10
4
46
2 14
1 1
12
19
1 26
20
2 18 17 2 2
11 2
12
1
A 7
12 4
3
15 14 20
3 3
3
35 35
1
1 6
1 34
3 47 30 1 13
LEAD/LAG DETAIL
SAMPLE
3 PORT
21

Control Piping (30 hp, gauge, wye-delta) - 147314-009 thru -012
35 1 22454-1 pressure switch (70-125#)
1 8698-011 pressure switch (150-210#)
38 1 128662 pressure gauge (0-300#)
42 1 147514-14 gauge panel
46 1 129251-025 plug valve

b 2 22749-010 Viton o-ring-0.25 i.d.
c 2 123157-008 Buna-N o-ring-0.18 i.d.
e 1 140406-904 Viton o-ring-0.35 i.d.
* Quantity of two on units with lead/lag control option.

Reference drawing.

Control Piping (30 hp, microprocessor, full voltage) - 147315-002
SEE AIREND GROUP
UPPER PORT
UPPER PORT
LOWER PORT
LOWER PORT
E 33
31 24
22
32 1
5 35
27 23 C
B 8 30
25 2
20
27 1
3 1
O 16
28 D
27
I P
3
34 9 3
3 1
14
20 3
15 1 18
4
3
2 10
2 1
1 1
3
1 19
12 12 2 2
A 7 14 1
12 4 (NOTE 2)
2 18
17 26 20 3
PRESSURE
3 SENSOR
27
1 6
29 36 F
1
1 13
SAMPLE
PORT
21

Control Piping (30 hp, microprocessor, full voltage) - 147315-002
34 1 129251-025 plug valve
36 1 128883-075 pipe plug-3/4-16 (o-ring)

b 2 22749-010 Viton o-ring-0.25 i.d.
c 2 123157-008 Buna-N o-ring-0.18 i.d.
e 1 140406-904 Viton o-ring-0.35 i.d.
f 1 140406-908 Viton o-ring-0.64 i.d.

Control Piping (30 hp, microprocessor, wye-delta) - 147315-003
SEE 3
AIREND
GROUP 24
C 23 1
D
28 16 25 2
3
22
1 32
32
18 3
31
1
1 30 25 B
3
1 8 5 33
P O
3 1
27
9 16
I
20
27 10
4
34
14 3
2
2 1
1
3
1 12
15
1 19
2 18 12 2 2
A 7 1
12 4
3
17 26 20
14
3 3
PRESSURE
SENSOR
1
27
6
1 29 35 F
1
13
SAMPLE
3 PORT
21


Control Piping (30 hp, microprocessor, wye-delta) - 147315-003
34 1 129251-025 plug valve
35 1 128883-075 pipe plug-3/4-16 (o-ring)

b 2 22749-010 Viton o-ring-0.25 i.d.
c 2 123157-008 Buna-N o-ring-0.18 i.d.
e 1 140406-904 Viton o-ring-0.35 i.d.
f 1 140406-908 Viton o-ring-0.64 i.d.

43 42 41 33 3
40
33 3 SEE DETAIL
35 FOR LEAD/LAG
33 3
39
1 30
3
38
1 3
32 20 1
1 3
37
28 E
31 2
23 C 18 16
SEE C 3
36 AIREND 25
GROUP 23
24
3 1 22
3 29
16 13 25
P 25 1
O
9
25
I
46 15 45 F
47
3 1
1
20 3
10
4
3
2
1
1
1 12
2 2
11 2
19
1
20
12 4
A 7 2 18 3 12
17 26 44
14
34
B
48 8 6 5
1
35 35 21 FLUID FILTER BLOCK
3 1 49
SAMPLE 27 D
3 50 30 PORT
LEAD/LAG DETAIL

6 1 125025-007 line filter orifice (Ø0.060)
27 1 128886-006 elbow-0.50 tube x 3/4-16 (o-ring)
35* 1 22454-1 pressure switch (70-125#)
1 8698-011 pressure switch (150-210#)
38 1 128662 pressure gauge (0-300#)
42 1 147514-14 gauge panel
46 1 129251-025 plug valve

b 2 22749-010 Viton o-ring-0.25 i.d.
c 2 123157-008 Buna-N o-ring-0.18 i.d.
d 2 140406-908 Viton o-ring-0.64 i.d.
e 1 129732-051 line filter kit (includes bowl seal, filter element, gasket)
f 1 140406-904 Viton o-ring-0.35 i.d.
* Quantity of two on units with lead/lag control option. Reference drawing.

1 3 1
28 D
18 16
SEE C 3
AIREND 31
GROUP 23
24
31
3 1 22
3 29
29
16 13 25
P 31
O 29
9
I
13 15 30 E
37
3 1
20 3
10
4
3
2
1
1
1 12
2
12 2
12 4
A 7 2 18 3 19
17 26 33
14
35
PRESSURE B
SENSOR
FLUID 36 8 6 5
21 FILTER 27
32
BLOCK
38 F
3 1
SAMPLE F 34
PORT


6 1 125025-007 line filter orifice (Ø0.060)
13 1 129251-025 plug valve
38 1 128883-075 pipe plug-3/4-16 (o-ring)

b 2 22749-010 Viton o-ring-0.25 i.d.
c 2 123157-008 Buna-N o-ring-0.18 i.d.
e 1 140406-904 Viton o-ring-0.35 i.d.
f 3 140406-908 Viton o-ring-0.64 i.d.

Air Piping (20/25/30 hp) - 146922-001/-002
3 A B
9
8
6 E B A 3
11
18
12
2
9
19
5 D
10
7
13
14 17
16
TO LINE FILTER
4 C D
15
13
20
14
15

Air Piping (20/25/30 hp) - 146922-001/-002
1 1 146893-17 formed tube assembly-par-flanged, 1.00 o.d.
2 1 147528 hose assembly-0.875 x 21.50 long
3 2 140676-020 elbow-1.00 tube x 1-5/8-12 (o-ring)
4 1 140682-023 connector-1.00 tube x 1-5/8-12 (o-ring)
5 1 140677-014 elbow-1.00 tube x 1.00-11.5 nptf (o-ring)
6 1 147573-3275 moisture separator
7* 1 146395 manual condensate drain
1 115698-125 electronic drain valve (Optional)
8 1 126020-010 pipe nipple-galvanized, 1.00 npt x 2.00
9 2 21740 pipe coupling-galvanized, 1.00 npt
10 4 142578-J21 cap screw-zinc, 1/4-20 unc x 3.00,
11 4 112272-J02 self-locking hex nut-zinc, 1/4-20 unc
18 4 141822-334 tube clamp-1.31 i.d.
19 2 141827-05 tube clamp cover plate-1.38 i.d.
20** 1 142125-1 extra strong brass nipple-0.25 npt x close
a 2 140406-916 Viton o-ring-1.17 i.d.

b 2 140675-007 Viton o-ring/face seal-1.18 i.d.
c 1 140406-920 Viton o-ring-1.48 i.d.
d 2 140675-006 Viton o-ring/face seal-0.93 i.d.
E 1 145999-050 Viton o-ring

* Electronic drain valve is optional.
** Item 20 (nipple) used only with electronic drain valve.

Air Piping (40/50 hp) - 146933-001/-002
C 10
1
15 16
A
7
5
14
C B 9
15 2
10 C
6
3
12
11
4
13
11 8 B C
3 4
17
TO LINE FILTER
12
13

Air Piping (40/50 hp) - 146933-001/-002
5 1 147573-3550 moisture separator
6 1 146395 manual condensate drain
1 115698-125* electronic drain valve (optional)
7 1 125868-021 pipe bushing-galvanized, 1.50 npt x 1.25 npt
10 2 140677-017 elbow-1.50 tube x 1-1/2-11.5 nptf (o-ring)
14 1 120806 u-bolt, 5/16-18 unc
15 6 112272-k02 self-locking hex nut-zinc, 5/16-18 unc
16 4 141631-k10 cap screw-5/16-18 unc x 0.75,
17** 1 142125-1 extra strong brass nipple-0.25 npt x close
a 1 145999-051 Viton o-ring

b 2 140406-924 Viton o-ring-1.72 i.d.
c 4 140675-008 Viton o-ring/face seal-1.49 i.d.

* Electronic drain valve is optional.
** Item 11 (nipple) used only with electronic drain valve.

Receiver (20/25/30 hp) - 147593-001
A 14
13
5
6
15 A
2 8
3
4 16
12
9
11
10
6
1
7

Receiver (20/25/30 hp) - 147593-001
1 1 147535-200 120 gallon receiver
2 1 110425-100 quarter turn valve
4 1 125868-029 pipe bushing-galvanized, 2.00 npt x 1.00 npt
5 1 110514-300 pressure gauge
7 1 2713 draincock-0.25 npt
8 1 143556-200 pressure relief valve
10 8 112272-N02 self-locking hex nut-zinc, 1/2-13 unc
11 2 146002-4 decal-Quincy logo, white (17.5 inch)
12 1 5042 decal-drain tank every day
13 1 146754-04 hose assembly-seal-lok, 45° bend
14 1 140677-014 elbow-1.00 tube x 1.00-11.5 nptf (o-ring)
15 1 140681-015 connector-1.00 nptf x 1.00 tube (o-ring)
a 2 140675-006 Viton o-ring/face seal-0.93 i.d.

Fluid Piping (20/25/30 hp) - 146908-001/-002
6 C D
D C 6
5
E
D C 6
A
6 C D

Fluid Piping (20/25/30 hp) - 146908-001/-002
1 1 128598 fluid filter element
1 146893-12* formed tube assembly-par-flanged, 0.75 o.d.
7 1 140682-017 connector-0.75 tube x 3/4-16 (o-ring)

b 1 140406-916 Viton o-ring-1.17 i.d.
c 4 140675-004 Viton o-ring/face seal-0.61 i.d.
d 4 140406-912 Viton o-ring-0.92 i.d.
e 1 140406-908 Viton o-ring-0.64 i.d.
* This tube assembly used only on 30 hp, 100 & 125 psi units.

Fluid Piping (40/50 hp) - 146924-001/-002
15 A B
11 13
9
12
10
B B
6
B
A A
7 A
13 15
13 3
AIREND
14 A C
13 A B
RESERVOIR

Fluid Piping (40/50 hp) - 146924-001/-002
1 1 142136 fluid filter element
(all 40 hp/50 hp, 150#)
1 146893-07 formed tube assembly-par-flanged, 1.00 o.d.
(50 hp, 100/125#)
6 1 146925 fluid manifold block
7 1 140536-1 thermal valve-cartridge
8 1 140537 fluid filter stud
9 1 146959 fluid manifold block support
10 1 2140 pipe plug-0.125 npt
11 2 141631-K10 cap screw-5/16-18 unc x 0.75,
12 2 110511-J07 hex head screw-zinc, 1/4-20 unc x 0.50

b 7 140406-916 Viton o-ring-1.17 i.d.
c 1 140406-912 Viton o-ring-0.92 i.d.

Reservoir (20/25/30 hp) - 146910-001
16
19
20
17
14
D
10
13
24
25
26
23
15
21
22
18 11 A
12 B
2
6
7
8
9

Reservoir (20/25/30 hp) - 146910-001
1 1 146913-175 air/fluid reservoir
8 1 129251-025 plug valve
11 1 129844-162 filler cap (o-ring)
12 1 129843-188 sightglass (o-ring)
14 1 146912 multi-purpose block
15 1 22749-156 Viton o-ring-4.25 i.d.
16 1 146914 air/fluid separator element
17 4 142578-Q20 cap screw-zinc, 5/8-11 unc x 2.75,
18 4 124370-Q02 locknut-5/8-11 unc
19 1 140147-2 thermal valve-cartridge
20 1 128599 fluid filter stud
23 1 22749-226 Viton o-ring-2.00 i.d.
24 1 147218-1 pressure relief valve cover
25 1 122560-12 u-bolt-zinc, 1/2-13 unc, 0.75 i.d. x 1.25
26 2 124370-J02 locknut-1/4-20 unc
a 1 140406-920 Viton o-ring-1.48 i.d.

b 1 140406-924 Viton o-ring-1.72 i.d.
c 1 147563 separator nipple
d 1 147564 minimum pressure check valve
1 147564k minimum pressure check valve kit


Reservoir (40/50 hp) - 146923-001/-002
A
18
18
13 E
23
F 19
B 6 23
20
21
8
22
(NOTE 1)
26 25
7 24
D
25 4
12
10
11 C
14 17
15 18
16

1) REFERENCE BOM FOR SCREW AND WASHER SIZE.
VARIES ACCORDING TO UNIT AIREND.

Reservoir (40/50 hp) - 146923-001/-002
1 1 146963-175 air/fluid reservoir
6 1 146932 multi-purpose block
7 1 22749-156 Viton o-ring-4.25 i.d.
8 1 22749-231 Viton o-ring-2.61 i.d.
9 2 146914 air/fluid separator element
10 4 142578-Q16 cap screw-zinc, 5/8-11 unc x 1.75,
11 1 129843-188 sightglass (o-ring)
12 1 129844-162 filler cap (o-ring)
13 1 128883-075 pipe plug-3/4-16 (o-ring)
17 1 129251-025 plug valve
19 1 128883-050 pipe plug-1/2-20 (o-ring)
20 1 147218 pressure relief valve cover
21 1 122560-08 u-bolt-zinc, 5/16-18 unc, 1.50 i.d. x 2.19
22 2 112272-K02 self-locking hex nut-zinc, 5/16-18 unc
23 2 2721 pipe plug-0.50 npt
grade 5 (@ 23 ft-lbs) (all 40 hp/50 hp, 150#)
4 142578-Q17 cap screw-zinc, 5/8-11 unc x 2.00,
grade 5 (@ 110 ft-lbs) (50 hp, 100/125#)
25 * 123115-10Z lockwasher-zinc, 0.63
26** 4 123115-08Z lockwasher-zinc, 0.50
a 1 147563 separator nipple

b 1 147565k minimum pressure check valve kit
c 1 140406-924 Viton o-ring-1.72 i.d.
d 1 140406-920 Viton o-ring-1.48 i.d.
e 2 140406-908 Viton o-ring-0.64 i.d.
F 1 140406-905 Viton o-ring-0.41 i.d.

* Quantity of 8 on 50 hp, 100/125#. Quantity of 4 on all 40 hp & on 50 hp, 150#.
** item 26 not used on 50 hp, 100/125#. (Reference drawing notes.)

Cooler (20/25/30 hp) - 146901-002/-003
17 16 15
11
1
2
12
8
13
5
9
6 11
7
12
LESS CABINET
WITH CABINET
11
4
14

1) ITEM 10 (RUBBER SEAL) IS NOT SHOWN AND IS USED
AROUND COOLER (AT ATTACHMENT TO SHROUD).

Cooler (20/25/30 hp) - 146901-002/-003
1 1 146917 combination cooler
2 1 146447-01 fan cone
3 1 147260-10 fan wheel-18”
4 1 147505 cooler support
5 1 147506-01 cooler brace
6 1 147508-01 access panel cover (less cabinet)
1 147508-02 access panel cover (with cabinet)
7 1 147059 fan housing cover plate
8 1 147510 cooler shroud
9 4 141631-L12 cap screw-3/8-16 unc x 1.00, grade 5 (@ 23 ft-lbs)
10 4 141528 rubber seal
11 14 141631-K10 cap screw-5/16-18 unc x 0.75,
13 8 129303L025 fender washer
15* 1 147509 fan guard
16* 6 122151 hex head screw-1/4-20 unc x 0.63,
17* 6 22456Z speed nut-grip, zinc, 1/4-20 unc

* These items not used on units with cabinet.

Cooler (40/50 hp) - 146926-001/-003
8
17
10
5
3
15

Cooler (40/50 hp) - 146926-001/-003
1 1 147530 cooler shroud
2 1 146927-01 cooler support
3 1 147533-01 fan motor panel
4 1 146447-01 fan cone
5 1 147260-01 fan wheel-18”
6 1 147529-01 access panel-cooler shroud (less cabinet)
1 147529-02 access panel-cooler shroud (with cabinet)
7 1 147059 fan housing cover plate
8 1 147249-01 fluid cooler
9 1 147249-02 aftercooler
10 1 146703-07 vent cover panel
11* 4 14654412025 lock screw-zinc, 12 mm x 25 mm
12* 16 110511-J07 hex head screw-zinc, 1/4-20 unc x 0.50
13* 12 141631-K10 cap screw-5/16-18 unc x 0.75,
14* 4 141631-L12 cap screw-3/8-16 unc x 1.00, grade 5 (@ 23 ft-lbs)
15 1 146927-03 pipe support bracket
16* 4 112272-K02 self-locking hex nut-zinc, 5/16-18 unc
17 1 147534-01 top panel-cooler shroud
18* 6 141631-J10 cap screw-1/4-20 unc x 0.75, grade 5 (@ 23 ft-lbs)
19* 6 22456Z speed nut-grip, zinc, 1/4-20 unc

* Hardware items not shown.

Cabinet (20/25/30 hp) - 147514-001/-002
5
3
6
1
7
10
9 12
20
8
1
14
15
19
4
13 11

Cabinet (20/25/30 hp) - 147514-001/-002
1 4 147514-01 corner post panel
2 2 147514-02 end rail panel
3 2 147514-03 side rail panel
4 2 147514-04 reveal post panel
5 1 147514-05 vented top panel
6 1 147514-06 cooler door panel
7 1 147514-07 side door panel
9 1 147514-09 front door panel
12 1 147514-12 panel assembly
13 1 146939-13 enclosure door extension panel
14 10 128954-3 quarter turn door latch
15 10 146682 door support
18* 41 110511-J07 hex head screw-zinc, 1/4-20 unc x 0.50
19 3 146021-2 decal-Q/Quincy, white (15 inch)
20 1 147514-15 cover panel (electronic control unit)
* Hardware items not shown.

Cabinet (40/50 hp) - 146939-001/-002
4 6
12
7
10
8
7
11
14 1
20 15
19
5
7
13

Cabinet (40/50 hp) - 146939-001/-002
3 2 146939-03 side rail panel
4 2 146939-04 end rail panel
6 1 146939-06 vented top panel
7 4 146939-07 corner post panel
8 1 146939-08 air intake panel
12 1 146939-12 cooler door panel
13 1 146939-13 enclosure door extension panel
14 10 128954-3 quarter turn door latch
15 10 146682 door support
20 1 146939-16 cover panel (electronic control unit)

Decals - 146955-020/-025/-030/-040/-050
1 AJ 3 6 5 1 AR 1 AJ
INSIDE ELECTRICAL
ENCLOSURE DOOR
1 AA
1 AF 4 10
1 AG 1 AH
1 AG 1 AG
1 AJ
1 AB
1 AQ
9 1 AJ

1) UNIT WITH MICROPROCESSOR CONTROL AND CABINET (PHANTOM) SHOWN.
DECAL LOCATIONS ARE GENERAL AND WILL BE ADJUSTED AS NECESSARY
FOR UNITS WITH GAUGE CONTROLS AND UNITS LESS CABINET.
2) ITEMS 5 & 6 ARE WIRE TIED TO THE E-STOP BUTTON.
3) ITEM 9 IS WIRE TIED TO THE SHIPPING SUPPORT BRACKET.

Decals - 146955-020/-025/-030/-040/-050
1 1 146001 safety decal sheet
3 1 147469-20 decal-QGD-20
1 147469-25 decal-QGD-25
1 147469-30 decal-QGD-30
1 147469-40 decal-QGD-40
1 147469-50 decal-QGD-50
4 1 142325 fluid level decal
5 1 141250 caution tag-jog motor
6 1 22177 tag-fluid type shipped with unit
7 1 128198 genuine Quincy components label
8 1 110690-001 plastic envelope
9 1 146028-1 warning tag-remove red brackets
10 1 143861 DECAL-THIS MACHINE PROTECTED WITH QUINSYN PG™
1 144048 DECAL-THIS MACHINE PROTECTED WITH QUINSYN PLUS
1 140519-3 decal-this machine protected with Quinsyn XP®
1 128426 DECAL-THIS MACHINE PROTECTED WITH QUINSYN-F®

Control Schematic (20/25 hp, gauge)
DPGS
DPGA
LEAD/LAG
ONLY PS PS
PG
CG CV
AE
CV
TG
LF
IV
P
O
BV
SG
ILCV
SHV
3WSV
2
1
3
RPG
SHV
SEP
PR
SL
AE AIREND OR
BV BLOWDOWN VALVE
CG CAPACITY GAUGE FF
CV CAPACITY VALVE
DPGA DIFFERENTIAL PRESSURE GAUGE (AIR FILTER)
DPGS DIFFERENTIAL PRESSURE GAUGE (SEPARATOR)
FF FLUID FILTER
FSV FLUID SAMPLE VALVE
ILCV INLINE CHECK VALVE MPCV
IV INLET VALVE
LF LINE FILTER FSV
MPCV MINIMUM PRESSURE CHECK VALVE
OR ORIFICE
PG PRESSURE GAUGE
PR PRESSURE REGULATOR
PS PRESSURE SWITCH
RES RESERVOIR
SG SIGHTGLASS RES
SHV SHUTTLE VALVE
SL SCAVENGE LINE
TG TEMPERATURE GAUGE
3WSV 3-WAY SOLENOID VALVE

Control Schematic (20/25 hp, microprocessor)
AE
CV
LF
IV
P
O
BV
SG
ILCV
SHV
3WSV
2
1
3
PG
SHV SEP
PR
SL FF
OR
MPCV
FSV
RES
AE AIREND OR ORIFICE
BV BLOWDOWN VALVE PG PRESSURE GAUGE
CV CAPACITY VALVE PR PRESSURE REGULATOR
FF FLUID FILTER RES RESERVOIR
FSV FLUID SAMPLE VALVE SEP SEPARATOR
ILCV INLINE CHECK VALVE SG SIGHTGLASS
IV INLET VALVE SHV SHUTTLE VALVE
LF LINE FILTER SL SCAVENGE LINE
MPCV MINIMUM PRESSURE CHECK VALVE 3WSV 3-WAY SOLENOID VALVE

Control Schematic (30 hp, gauge, full voltage)
H
DPGS
DPGA LEAD/LAG
ONLY PS PS
PG
CG CV
AE
TG
AE AIREND
BV BLOWDOWN VALVE
CG CAPACITY GAUGE
CV CAPACITY VALVE IV
DPGA DIFFERENTIAL PRESSURE
GAUGE (AIR FILTER)
DPGS DIFFERENTIAL PRESSURE
GAUGE (SEPARATOR)
FF FLUID FILTER
ILCV INLINE CHECK VALVE
ILCV CV
IV INLET VALVE
LF LINE FILTER
MPCV MINIMUM PRESSURE CHECK VALVE SG
OR ORIFICE
PG PRESSURE GAUGE
PS PRESSURE SWITCH
RES RESERVOIR LF
SG SIGHTGLASS
SHV SHUTTLE VALVE
SL SCAVENGE LINE
TG TEMPERATURE GAUGE O
P
I
BV
SHV
3WSV
1 2
PG
3
SHV
SEP
PR
SL OR
FF
MPCV
FSV
RES

Control Schematic (30 hp, gauge, wye-delta)
DPGS
L
DPGA LEAD/LAG
ONLY
PS PS
PG
CG CV
AE
CV
TG
LOWER
PORT
LF
IV
P O
SG
BV
I ILCV
SHV
3WSV
2
1
3
PG
SHV
SEP
AE AIREND
PR
BV BLOWDOWN VALVE
CG CAPACITY GAUGE
CV CAPACITY VALVE
GAUGE (AIR FILTER) OR FF
SL
GAUGE (SEPARATOR)
FF FLUID FILTER
IV INLET VALVE MPCV
LF LINE FILTER
MPCV MINIMUM PRESSURE CHECK VALVE FSV
OR ORIFICE
PG PRESSURE GAUGE
PS PRESSURE SWITCH
RES RESERVOIR
SG SIGHTGLASS
SHV SHUTTLE VALVE RES
SL SCAVENGE LINE

Control Schematic (30 hp, microprocessor, full voltage)
AE
IV
ILCV
CV
SG
LF
I P
BV
SHV
3WSV
2
1 PG
3
SEP
SHV
PR FF
SL
OR
MPCV
FSV
RES
AE AIREND MPCV MINIMUM PRESSURE CHECK VALVE

BV BLOWDOWN VALVE OR ORIFICE
CV CAPACITY VALVE PG PRESSURE GAUGE
FF FLUID FILTER RES RESERVOIR
FSV FLUID SAMPLE VALVE SG SIGHTGLASS
ILCV INLINE CHECK VALVE SHV SHUTTLE VALVE
IV INLET VALVE SL SCAVENGE LINE
LF LINE FILTER 3WSV 3-WAY SOLENOID VALVE

Control Schematic (30 hp, microprocessor, wye-delta)
AE
CV
LF
IV
P
SG
O
BV
I ILCV
SHV
3WSV
2
1
3
PG
SHV
SEP
PR
SL
FF
AE AIREND
BV BLOWDOWN VALVE OR PS
CV CAPACITY VALVE
FF FLUID FILTER
IV INLET VALVE MPCV
LF LINE FILTER
OR ORIFICE FSV
PG PRESSURE GAUGE
PS PRESSURE SENSOR
RES RESERVOIR
SG SIGHTGLASS
SHV SHUTTLE VALVE
SL SCAVENGE LINE RES

Control Schematic (40/50 hp, gauge)
DPGS
DPGA
LEAD/LAG
ONLY PS PS
PG
CG CV
LF
TG AE
CV
IV
P
O
BV
SHV
3WSV
2
1
3
PG
SHV
AE AIREND
PR BV BLOWDOWN VALVE
CG CAPACITY GAUGE SL
CV CAPACITY VALVE
GAUGE (AIR FILTER) SEP
GAUGE (SEPARATOR) FSV
FF FLUID FILTER SEP
SG ILCV
IV INLET VALVE
LF LINE FILTER OR
OR ORIFICE MPCV
PG PRESSURE GAUGE
PS PRESSURE SWITCH
RES RESERVOIR
SG SIGHTGLASS
SHV SHUTTLE VALVE
SL SCAVENGE LINE
3WSV 3-WAY SOLENOID VALVE RES

Control Schematic (40/50 hp, microprocessor)
LF
AE
CV
IV
BV
O
I
FSV
SHV
3WSV FF
2
1
3
SHV
PG
PR
SL
SEP SEP
AE AIREND PS
BV BLOWDOWN VALVE
CV CAPACITY VALVE
FF FLUID FILTER SG ILCV
ILCV INLINE CHECK VALVE OR
IV INLET VALVE
LF LINE FILTER
MPCV
OR ORIFICE
PG PRESSURE GAUGE
PS PRESSURE SENSOR
RES RESERVOIR
SG SIGHTGLASS
SHV SHUTTLE VALVE
SL SCAVENGE LINE RES

Electrical Control Diagram (full voltage, auto dual)
WP2072A
INSIDE ELECTRICAL ENCLOSURE

POWER
SUPPLY
1FU
L1 L2 L3
2FU
STOP START
MOTOR CIRCUIT
17 3FU 1 CPT1 N
PB2 PB1 OVERCURRENT
PROTECTION
3 G SEE NOTE 1
2 POWER
ON
G
PL1
CR1
J1
17 5
OUTSIDE ELECTRICAL ENCLOSURE
1TS * CR2
6
CR2 7 PPR
H.A.T.
8 PL2
R
CR2
CR1
* FU7
*
A
* FU8 PHASE
B PROTECTION
17
15
TR1
18
9 10 11 12
M1
N
OL4
* FU9
C
RELAY
CR2 OL1 OL4

M4
M1
CONTINOUS AUTO
RUN DUAL HM
M4 OL1
SS1
SEE NOTE 3
TR1
A1 A2
17 N FAN MOTOR
SEE TABLE
COMPRESSOR
J2 MOTOR
PS1
18 15 16
M1 SV1
UNLOAD
NOMENCLATURE
FU FUSE OL OVERLOAD RELAY

NOTES PB PUSH BUTTON M CONTACTOR
1) AT INSTALLATION THE CUSTOMER IS TO PROVIDE DISCONNECT AND SS SELECTOR SWITCH SV SOLENOID VALVE
BRANCH CIRCUIT OVERCURRENT PROTECTION IN ACCORDANCE WITH CR CONTROL RELAY VS VACUUM SWITCH
THE NATIONAL ELECTRICAL CODE AND/OR ANY LOCAL CODES CPT CONTROL POWER TRANS SCREW TERMINAL
HAVING PRECEDENCE. TS TEMP. SWITCH N OCTAL SOCKET NUMBER
2) UNLESS OTHERWISE SPECIFIED ALL WIRES ARE RED EXCEPT "N" WIRES ARE
WHITE AND "G" WIRES ARE GREEN.
HAT
PL
HIGH AIR TEMP.
PANEL LIGHT
*
HM
OPTIONALS
HOUR METER
3) TR1 TO BE SET TO OFF-DELAY AND HAVE A TIME SETTING OF 10-15 MINUTES. TR TIMING RELAY J JUMPERS

Electrical Control Diagram (wye-delta, auto dual)
WP2072A1
POWER
INSIDE ELECTRICAL ENCLOSURE
SUPPLY
1FU L1 L2 L3
2FU
STOP START
MOTOR CIRCUIT
17 3FU 1 CPT1 N
PB2 PB1 OVERCURRENT
PROTECTION
3 G SEE NOTE 1
2 POWER
ON
G
PL1
CR1
J1
17 5
OUTSIDE ELECTRICAL ENCLOSURE
1TS * CR2
CR2 7 PPR
6
* FU7
*
A
FU8 PHASE
B PROTECTION
8 PL2
H.A.T.
R
* FU9
C
RELAY
CR2
CR1
*
SEE NOTE 4
TR2
17 TR1 9 10 11 12 A1 A2
N
15 18 OL4
CR2 OL1 OL4 M4
M3
CONTINOUS HM M2
AUTO OL1
RUN DUAL
M4
TR2 22 M2 23 M3
SS1 15 16
TR2 24
15 18 FAN MOTOR
COMPRESSOR
M2 M3 25 M2 MOTOR
24
NOMENCLATURE
NOTES
1) AT INSTALLATION THE CUSTOMER FU FUSE
IS TO PROVIDE DISCONNECT AND PB PUSH BUTTON
BRANCH CIRCUIT OVERCURRENT SS SELECTOR SWITCH
SEE NOTE 3 PROTECTION IN ACCORDANCE WITH CR CONTROL RELAY
TR1 THE NATIONAL ELECTRICAL CODE CPT CONTROL POWER TRANS
17 A1 A2 AND/OR ANY LOCAL CODES HAVING TS TEMP. SWITCH
N
PRECEDENCE. HAT HIGH AIR TEMP.
SEE TABLE 2) UNLESS OTHERWISE SPECIFIED PL PANEL LIGHT
ALL WIRES ARE RED EXCEPT "N" TR TIMING RELAY
J2 WIRES ARE WHITE AND "G" WIRES OL OVERLOAD RELAY
ARE GREEN. M CONTACTOR
PS1
18 15 16 3) TR1 TO BE SET TO OFF-DELAY AND SV SOLENOID VALVE
HAVE A TIME SETTING OF 10-15 VS VACUUM SWITCH
SV1 MINUTES. SCREW TERMINAL
M2 4) TR2 TO BE SET TO ON-DELAY AND
UNLOAD N OCTAL SOCKET NUMBER
HAVE A TIME SETTING OF 6 SECONDS.
*
HM
OPTIONALS
HOUR METER

Electrical Control Diagram (microprocessor control, full voltage)
WP2073A
HMI
FU1
FU2 POWER
SUPPLY
START PLC
PORT 0 FU3 CPT
STOP 5 4 X1 N L1 L2 L3
120VAC X3
PORT 1 FU4 19 X2 MOTOR CIRCUIT
24VAC OVERCURRENT
PROTECTION
(NOTE 1)
M1 28 SV2
1M 2
24 N
17 OL4 10 OL1 PACKAGE DRAIN A

9 *
I0.0 PHASE
PROTECTION B
RELAY
J2 C
17 7
SEE NOTE 2 I0.1
J3
17 16
SEE NOTE 3 I0.2
L1
J6 18 N
I0.3
M1
J5
DRYER RUNNING 25 PB1
I0.4 E-STOP OL4
120VAC 1
1L *CR1
DRYER FAULT 31 GENERAL FAULT
I0.5 29
Q0.0 OL1
J1
E-STOP M4
17 *PPR 13 Q0.1
14
I0.6
Q0.2
M4 120VAC
15 2L HOUR
I0.7
METER
FAN MOTOR
24 2M Q0.3
M1 COMPRESSOR
8 J4 11 MOTOR
I1.0 Q0.4
Q0.5 M4 WHITE
I1.1 WHITE
Q0.6 WHITE
I1.2 24VAC 2
3L
SV1
CT1
CT2
CT3
3 OL1
Q0.7 N
I1.3 UNLOAD T3 T2 T1
Q1.0 BLACK
I1.4 BLACK
Q1.1 BLACK
499 OHM, 1% METAL
I1.5
FILM, 1/4 WATT
20 WHITE PRESSURE SENSOR

B+ 4-20Ma *THIS CONFIGURATION USED
499 OHM, 1% METAL RED 0-300 PSI ONLY WITH DRIVE MOTOR
M FILM, 1/4 WATT
OVERLOAD THAT USES CT'S
24VDC
L+ 23 2 3 TEMPERATURE SENSOR
17 A+ 4-20Ma
M
1 4
0-300 F
24 17 COMPRESSOR
MOTOR
20/25/30
* HORSE POWER
NOMENCLATURE GENERAL FAULT CONTACT UNITS
FU FUSE X7 CR1 X5 CR1 X6 230V
1) AT INSTALLATION, CUSTOMER IS TO PROVIDE DISCONNECT
PB PUSH BUTTON SINGLE PHASE
AND BRANCH CIRCUIT OVERLOAD PROTECTION IN ACCORDANCE
SS SELECTOR SWITCH POWER SUPPLY
WITH THE NATIONAL ELECTRICAL CODE AND/OR ANY LOCAL
CODES HAVING PRECEDENCE. CR CONTROL RELAY
CPT CONTROL POWER TRANSFORMER L1 L2
2) TO ENABLE REMOTE START REMOVE J2 . UNIT MUST BE
LOCALLY STARTED BEFORE REMOTE INPUT WILL WORK. TS TEMPERATURE SENSOR
WHEN CONTACT BETWEEN 17 AND 7 IS CLOSED THE UNIT HAT HIGH AIR TEMPERATURE MOTOR CIRCUIT
WILL START. PLC PROGRAMMABLE LOGIC CONTROLLER OVERCURRENT
3) TO ENABLE REMOTE UNLOAD REMOVE J3. WHEN CONTACT CT CURRENT TRANSFORMER PROTECTION
BETWEEN 17 AND 16 IS CLOSED THE UNIT WILL LOAD. OL OVERLOAD RELAY (NOTE 1)
M CONTACTOR
SV SOLENOID VALVE
PS PRESSURE SENSOR
X SCREW TERMINAL 22
2 NUMBER DESIGNATOR ON DEVICE 1 2
* OPTIONAL
HMI HUMAN MACHINE INTERFACE M1 *
30 DRYER

Electrical Control Diagram (microprocessor control, wye-delta)
WP2073B
HMI
FU1
FU2 POWER
SUPPLY
START PLC
PORT 0 FU3 CPT
STOP 5 4 X1 N L1 L2 L3
120VAC X3
PORT 1 FU4 19 X2 MOTOR CIRCUIT
24VAC OVERCURRENT
PROTECTION
(NOTE 1)
M2 28 SV2
1M 2
24 N
OL4 OL1 PACKAGE DRAIN A
10 9 *
I0.0 PHASE
PROTECTION B
RELAY
J2 C
17 7
SEE NOTE 2 I0.1
J3
17 16
SEE NOTE 3 I0.2
L1
J6 18 N
I0.3
M3 M2
J5
DRYER RUNNING PB1
25
I0.4 E-STOP
OL4
120VAC 1
1L *CR1
DRYER FAULT 31 GENERAL FAULT
I0.5 29
Q0.0 OL1
J1
E-STOP M4
17 *PPR 13 Q0.1
14
I0.6
Q0.2 M4
M4 120VAC
15 2L
I0.7 HOUR COMPRESSOR
METER MOTOR
FAN MOTOR
24 2M Q0.3
M3 M2
8 11
I1.0 Q0.4
M2 26 M3
12
Q0.5
I1.1
Q0.6
WHITE
I1.2 24VAC 2
3L WHITE
SV1
3 WHITE
Q0.7 N M3 M2
I1.3 UNLOAD
CT1
CT2
CT3
Q1.0 OL1
I1.4
Q1.1 T3 T2 T1
BLACK
499 OHM, 1% METAL
I1.5
FILM, 1/4 WATT BLACK
20 WHITE COMPRESSOR BLACK
PRESSURE SENSOR
B+ 4-20Ma MOTOR
499 OHM, 1% METAL RED 0-300 PSI
M FILM, 1/4 WATT
24VDC
L+ 23 2 3 TEMPERATURE SENSOR
17 A+ 4-20Ma
M
1 4
0-300 F
24 17 *THIS CONFIGURATION USED ONLY WITH
DRIVE MOTOR OVERLOAD THAT USES CT'S
20/25/30
GENERAL FAULT CONTACT HORSE POWER
UNITS
NOTES-UNLESS OTHERWISE SPECIFIED: X7 CR1 X5 CR1 X6
1) AT INSTALLATION, CUSTOMER IS TO PROVIDE DISCONNECT NOMENCLATURE 230V
AND BRANCH CIRCUIT OVERLOAD PROTECTION IN ACCORDANCE SINGLE PHASE
FU FUSE POWER SUPPLY
WITH THE NATIONAL ELECTRICAL CODE AND/OR ANY LOCAL
PB PUSH BUTTON
CODES HAVING PRECEDENCE.
SS SELECTOR SWITCH L1 L2
2) TO ENABLE REMOTE START REMOVE J2 . UNIT MUST BE
CR CONTROL RELAY
LOCALLY STARTED BEFORE REMOTE INPUT WILL WORK.
CPT CONTROL POWER TRANSFORMER
WHEN CONTACT BETWEEN 17 AND 7 IS CLOSED THE UNIT MOTOR CIRCUIT
TS TEMPERATURE SENSOR
WILL START. OVERCURRENT
HAT HIGH AIR TEMPERATURE
3) TO ENABLE REMOTE UNLOAD REMOVE J3. WHEN CONTACT PROTECTION
PLC PROGRAMMABLE LOGIC CONTROLLER
BETWEEN 17 AND 16 IS CLOSED THE UNIT WILL LOAD. (NOTE 1)
CT CURRENT TRANSFORMER
4) DRYERS FOR THE 20-30HP UNITS WILL BE 220V SINGLE
OL OVERLOAD RELAY
PHASE. DRYERS FOR THE 40-60HP UNITS WILL BE THE SAME
M CONTACTOR
THREE PHASE VOLTAGE AS THE UNIT.
SV SOLENOID VALVE
PS PRESSURE SENSOR 22
X SCREW TERMINAL 1 2
2 NUMBER DESIGNATOR ON DEVICE *
* OPTIONAL M1
30 DRYER
HMI HUMAN MACHINE INTERFACE

Standard Terms and Conditions
Quincy Compressor and Ortman Fluid Power Divisions
TITLE & LIEN RIGHTS: The equipment shall remain personal property, regardless of how affixed
to any realty or structure. Until the price (including any notes given therefore) of the equipment
has been fully paid in cash, Seller shall, in the event of Buyer’s default, have the right to
repossess such equipment.
PATENT INFRINGMENT: If properly notified and given an opportunity to do so with friendly
assistance, Seller will defend Buyer and the ultimate user of the equipment from any actual
or alleged infringement of any published United States patent by the equipment or any
part thereof furnished pursuant hereto (other than parts of special design, construction, or
manufacture specified by and originating with Buyer), and will pay all damages and costs
awarded by competent court in any suit thus defended or of which it may have had notice and
opportunity to defend as aforesaid.
STANDARD WARRANTY: Seller warrants that products of its own manufacture will be free from
defects in workmanship and materials under normal use and service for the period specified in
the product instruction manual. Warranty for service parts will be ninety (90) days from date of
factory shipment. Electric Motors, gasoline and diesel engines, electrical apparatus and all other
accessories, components and parts not manufactured by Seller are warranted only to the extent
of the original manufacturer’s warranty.
Notice of the alleged defect must be given to the Seller, in writing with all identifying details
including serial number, type of equipment and date of purchase within thirty (30) days of the
discovery of the same during the warranty period.
Seller’s sole obligation on this warranty shall be, at its option, to repair or replace or refund the
purchase price of any product or part thereof which proves to be defective. If requested by
Seller, such product or part thereof must be promptly returned to seller, freight prepaid, for
inspection.
Seller warrants repaired or replaced parts of its own manufacture against defects in materials
and workmanship under normal use and service for ninety (90) days or for the remainder of the
warranty on the product being repaired.
This warranty shall not apply and Seller shall not be responsible or liable for:
(a) Consequential, collateral or special losses or damages;
(b) Equipment conditions caused by fair wear and tear, abnormal conditions of use, accident,
neglect or misuse of equipment, improper storage or damage resulting during shipping;
(c) Deviation from operating instructions, specifications or other special terms of sale;
(d) Labor charges, loss or damage resulting from improper operation, maintenance or repairs
made by person(s) other than Seller or Seller’s authorized service station.
In no event shall Seller be liable for any claims whether arising from breach of contract or
warranty or claims of negligence or negligent manufacture in excess of the purchase price.
THIS WARRANTY IS THE SOLE WARRANTY OF SELLERS AND ANY OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED IN LAW OR IMPLIED IN FACT, INCLUDING ANY
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE ARE HEREBY
SPECIFICALLY EXCLUDED.
LIABILITY LIMITATIONS: Under no circumstances shall the Seller have any liability for liquidated
damages or for collateral, consequential or special damages or for loss of profits, or for actual
losses or for loss of production or progress of construction, whether resulting from delays in
delivery or performance, breach of warranty, negligent manufacture or otherwise.
ENVIROMENTAL AND OSHA REQUIREMENTS: At the time of shipment of the equipment from
the factory, Quincy Compressor / Ortman Fluid Power will comply with the various Federal,
State and local laws and regulations concerning occupational health and safety and pollution.
However, in the installation and operation of the equipment and other matters over which the
seller has no control, the Seller assumes no responsibility for compliance with those laws and
regulations, whether by the way of indemnity, warranty or otherwise.

Standard Terms and Conditions
Quincy Compressor and Ortman Fluid Power Divisions
LEGAL EFFECT: Except as expressly otherwise agreed to in writing by an authorized

representative of Seller, the following terms and conditions shall apply to and form a part of
this order and any additional and/or different terms of Buyer’s purchase order or other form of
acceptance are rejected in advance and shall not become a part of this order.
The rights of Buyer hereunder shall be neither assignable nor transferable except with the
written consent of Seller.
This order may not be canceled or altered except with the written consent of Seller and upon
terms which will indemnify Seller against all loss occasioned thereby. All additional costs
incurred by Seller due to changes in design or specifications, modification of this order or
revision of product must be paid for by Buyer.
In addition to the rights and remedies conferred upon Seller by this order, Seller shall have all
rights and remedies conferred at law and in equity and shall not be required to proceed with the
performance of this order if Buyer is in default in the performance of such order or of any other
contract or order with seller.
TERMS OF PAYMENT: Unless otherwise specified in the order acknowledgment, the terms
of payment shall be net cash within thirty (30) days after shipment. These terms shall apply
to partial as well as complete shipments. If any proceeding be initiated by or against Buyer
under any bankruptcy or insolvency law, or in the judgment of Seller the financial condition of
Buyer, at the time the equipment is ready for shipment, does not justify the terms of payment
specified, Seller reserves the right to require full payment in cash prior to making shipment. If
such payment is not received within fifteen (15) days after notification of readiness for shipment,
Seller may cancel the order as to any unshipped item and require payment of its reasonable
cancellation charges.
If Buyer delays shipment, payments based on date of shipment shall become due as of the date
when ready for shipment. If Buyer delays completion of manufacture, Seller may elect to require
payment according to percentage of completion. Equipment held for Buyer shall be at Buyer’s
risk and storage charges may be applied at the discretion of Seller.
Accounts past due shall bare interest at the highest rate lawful to contract for but if there is
no limit set by law, such interest shall be eighteen percent (18%). Buyer shall pay all cost and
expenses, including reasonable attorney’s fees, incurred in collecting the same, and no claim,
except claims within Seller’s warranty of material or workmanship, as stated below, will be
recognized unless delivered in writing to Seller within thirty (30) days after date of shipment.
TAXES: All prices exclude present and future sales, use, occupation, license, excise, and other
taxes in respect of manufacture, sales or delivery, all of which shall be paid by Buyer unless
included in the purchase price at the proper rate or a proper exemption certificate is furnished.
ACCEPTANCE: All offers to purchase, quotations and contracts of sales are subject to final
acceptance by an authorized representative at Seller’s plant.
DELIVERY: Except as otherwise specified in this quotation, delivery will be F. O. B. point of
shipment. In the absence of exact shipping instruction, Seller will use its discretion regarding
best means of insured shipment. No liability will be accepted by Seller for so doing. All
transportation charges are at Buyer’s expense. Time of delivery is an estimate only and is based
upon the receipt of all information and necessary approvals. The shipping schedule shall not be
construed to limit seller in making commitments for materials or in fabricating articles under this
order in accordance with Seller’s normal and reasonable production schedules.
Seller shall in no event be liable for delays caused by fires, acts of God, strikes, labor difficulties,
acts of governmental or military authorities, delays in transportation or procuring materials, or
causes of any kind beyond Seller’s control. No provision for liquidated damages for any cause
shall apply under this order. Buyer shall accept delivery within thirty (30) days after receipt
of notification of readiness for shipment. Claims for shortages will be deemed to have been
waived if not made in writing within ten (10) days after the receipt of the material in respect of
which any such shortage is claimed. Seller is not responsible for loss or damage in transit after
having received “In Good Order” receipt from the carrier. All claims for loss or damage in
transit should be made to the carrier.

Notes
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________
_ _______________________________________________________

Quincy Compressor Products: 217.222.7700
E-mail: [email protected] © 2008 Quincy Compressor, an EnPro Industries company
Website: quincycompressor.com All Rights Reserved. Litho in U.S.A.

Quincy QGD 20-25-30 QGD 40 50 Parts Manual

Uploaded by

Copyright:

Available Formats

Quincy QGD 20-25-30 QGD 40 50 Parts Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quincy QGD 20-25-30 QGD 40 50 Parts Manual

Uploaded by

Copyright:

Available Formats

QGD-20/25/30

Manual No. 65112-1A

May 2009 Edition

Airend (50 hp, 100/125#)................................................................................................. 8-9

Book Update: 05/01/09

Quincy Compressor® - QGD

Ordering Replacement Parts

Quincy Compressor® - QGD 

HQuinSyn Plus™H HQuinSyn XP®H

HQuinSyn PG™H HQuinSyn F® (food grade)H

Serial No.______________________________________ Fluid Originally Used:_ ____________________________

Fluid Now Used (if changed):_ _____________________ New Fluid To Be Used:_____________________________

Additional information regarding fluid specifications can be found in the Instruction

• Fluid Analysis Kit

 Quincy Compressor® - QGD

Quincy Compressor® - QGD 

NOTES - UNLESS OTHERWISE SPECIFIED:

Shaft Seal Kit - 140209

Reference Instruction Manual to install compressor

 Quincy Compressor® - QGD

Component Maintenance Parts

a 2 140406-908 Viton o-ring-0.64 i.d.

* Items not sold separately, must be ordered as a complete airend.

Quincy Compressor® - QGD 

NOTES - UNLESS OTHERWISE SPECIFIED:

Shaft Seal Kit - 140209

Reference Instruction Manual to install compressor

 Quincy Compressor® - QGD

Component Maintenance Parts

A 2 140406-904 Viton o-ring-0.35 i.d.

* Items not sold separately, must be ordered as a complete airend.

Quincy Compressor® - QGD 

Shaft Seal Kit - 140209

Reference Instruction Manual to install compressor

 Quincy Compressor® - QGD

Component Maintenance Parts

a 2 140406-908 Viton o-ring-0.64 i.d.

* Items not sold separately, must be ordered as a complete airend.

Quincy Compressor® - QGD 

10 Quincy Compressor® - QGD

Component Maintenance Parts

@ Indicates torque value in foot pounds (lubricated threads).

Quincy Compressor® - QGD 11

NOTES-UNLESS OTHERWISE SPECIFIED:

Item No. Qty. Part Number Description

@ Indicates torque value in foot pounds (lubricated threads).

12 Quincy Compressor® - QGD

NOTES-UNLESS OTHERWISE SPECIFIED:

Item No. Qty. Part Number Description

Quincy Compressor® - QGD 13

NOTES-UNLESS OTHERWISE SPECIFIED:

14 Quincy Compressor® - QGD

* This inlet valve configuration used on 30 hp units only at 150 psig.

Quincy Compressor® - QGD 15

16 Quincy Compressor® - QGD

@ Indicates torque value in foot pounds (lubricated threads).

Quincy Compressor® - QGD 17

NOTE-UNLESS OTHERWISE SPECIFIED: 23

18 Quincy Compressor® - QGD

* Items 21, 22 & 23 used only on 30 hp, wye-delta units.

Quincy Compressor® - QGD

Fluid Now Used (if changed):_ _ New Fluid To Be Used:_________

Quincy Compressor® - QGD

Quincy Compressor® - QGD

Quincy Compressor® - QGD

Quincy Compressor® - QGD

Quincy Compressor® - QGD

Quincy Compressor® - QGD

Quincy Compressor® - QGD

Quincy Compressor® - QGD