TAS5342A

TM
TAS5342A
www.ti.com ........................................................................................................................................................................................... SLAS623 – NOVEMBER 2008
100 W STEREO DIGITAL AMPLIFIER POWER STAGE

1FEATURES
• Total Power Output (Bridge Tied Load)
23
DESCRIPTION
– 2 × 100 W at 10% THD+N Into 4 Ω The TAS5342A is a high-performance, integrated
– 2 × 80 W at 10% THD+N Into 6 Ω stereo digital amplifier power stage designed to drive
a 4-Ω bridge-tied load (BTL) at up to 100 W per
– 2 × 65 W at 10% THD+N Into 8 Ω channel with low harmonic distortion, low integrated
• Total Power Output (Single Ended) noise, and low idle current.
– 4 × 40 W at 10% THD+N Into 3 Ω The TAS5342A has a complete protection system
– 4 × 30 W at 10% THD+N Into 4 Ω integrated on-chip, safeguarding the device against a
• Total Power Output (Parallel Mode) wide range of fault conditions that could damage the
system. These protection features are short-circuit
– 1 × 200 W at 10% THD+N Into 2 Ω protection, over-current protection, under voltage
– 1 × 160 W at 10% THD+N Into 3 Ω protection, over temperature protection, and a loss of
• >110 dB SNR (A-Weighted With TAS5518 PWM signal (PWM activity detector).
Modulator) A power-on-reset (POR) circuit is used to eliminate
• <0.1% THD+N (1 W, 1 kHz) power-supply sequencing that is required for most
• Supports PWM Frame Rates of 192 kHz to power-stage designs.
432 kHz BTL OUTPUT POWER
vs
• Resistor-Programmable Current Limit
SUPPLY VOLTAGE
• Integrated Self-Protection Circuitry, Including: 130
125
– Under Voltage Protection 120 TC = 75°C
115 THD+N at 10%
– Overtemperature Warning and Error 110
105
– Overload Protection 100
PO – Output Power – W
95
– Short-Circuit Protection 90
85
– PWM Activity Detector 80
75
• Standalone Protection Recovery 70
4Ω
65
• Power-On Reset (POR) to Eliminate System 60
55
Power-Supply Sequencing 50
• High-Efficiency Power Stage (>90%) With 45
40
80-mΩ Output MOSFETs 35 6Ω
30
• Thermally Enhanced Package 44-Pin HTSSOP 25
20
(DDV) 15 8Ω
• Error Reporting, 3.3-V and 5.0-V Compliant
10
5
• EMI Compliant When Used With 0

0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
Recommended System Design PVDD – Supply Voltage – V
APPLICATIONS PurePath Digital™
• Mini/Micro Audio System

• DVD Receiver
• Home Theater
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2 PurePath Digital, PowerPad are trademarks of Texas Instruments.
3 All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2008, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TAS5342A
SLAS623 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
GENERAL INFORMATION
Terminal Assignment
The TAS5342A is available in a thermally enhanced package 44-pin HTSSOP PowerPad™ package (DDV)
This package contains a thermal pad that is located on the top side of the device for convenient thermal coupling
to the heatsink.
DDV PACKAGE
(TOP VIEW)
GVDD_B 1 44 GVDD_A
OTW 2 43 BST_A
NC 3 42 NC
NC 4 41 PVDD_A
SD 5 40 PVDD_A
PWM_A 6 39 OUT_A
RESET_AB 7 38 GND_A
PWM_B 8 37 GND_B
OC_ADJ 9 36 OUT_B
GND 10 35 PVDD_B
AGND 11 34 BST_B
VREG 12 33 BST_C
M3 13 32 PVDD_C
M2 14 31 OUT_C
M1 15 30 GND_C
PWM_C 16 29 GND_D
RESET_CD 17 28 OUT_D
PWM_D 18 27 PVDD_D
NC 19 26 PVDD_D
NC 20 25 NC
VDD 21 24 BST_D
GVDD_C 22 23 GVDD_D
P0016-02
2 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5342A

TAS5342A
Protection MODE Selection Pins

Protection modes are selected by shorting M1, M2, and M3 to VREG or GND.
MODE PINS
Mode Name PWM Input (1) Description
M3 M2 M1
0 0 0 BTL mode 1 2N All protection systems enabled
0 0 1 BTL mode 2 2N Latching shudown on, PWM activity detector and OLP disabled
0 1 0 BTL mode 3 1N All protection systems enabled
(2)
0 1 1 PBTL mode 1N / 2N All protection systems enabled
1 0 0 SE mode 1 1N All protection systems enabled (3)
1 0 1 SE mode 2 1N Latching shudown on, PWM activity detector and OLP disabled (3)
1 1 0
Reserved
1 1 1
(1) The 1N and 2N naming convention is used to indicate the number of PWM lines to the power stage per channel in a specific mode.
(2) PWM_D is used to select between the 1N and 2N interface in PBTL mode (Low = 1N; High = 2N). PWM_D is internally pulled low in
PBTL mode. PWM_A is used as the PWM input in 1N mode and PWM_A and PWM_B are used as inputs for the 2N mode.
(3) PPSC detection system disabled.
Package Heat Dissipation Ratings (1)

PARAMETER TAS5342ADDV
RθJC (°C/W)—2 BTL or 4 SE channels 1.3
RθJC (°C/W)—1 BTL or 2 SE channel(s) 2.6
RθJC (°C/W)—1 SE channel 5.0
(2)
Power Pad area 36 mm2
(1) JC is junction-to-case, CH is case-to-heatsink.

(2) RθCH is an important consideration. Assume a 2-mil thickness of high performance grease with a thermal conductivity at 2.5W/m-K
between the pad area and the heat sink. The RθCH with this condition is 0.6°C/W for the DDV package.
Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 3

TAS5342A
ABSOLUTE MAXIMUM RATINGS

(1)
over operating free-air temperature range unless otherwise noted
TAS5342A
VDD to AGND –0.3 V to 13.2 V
GVDD_X to AGND –0.3 V to 13.2 V
(2)
PVDD_X to GND_X –0.3 V to 53 V
(2)
OUT_X to GND_X –0.3 V to 53 V
(2)
BST_X to GND_X –0.3 V to 66.2 V
(2)
BST_X to GVDD_X –0.3 V to 53 V
VREG to AGND –0.3 V to 4.2 V
GND_X to GND –0.3 V to 0.3 V
GND_X to AGND –0.3 V to 0.3 V
GND to AGND –0.3 V to 0.3 V
PWM_X, OC_ADJ, M1, M2, M3 to AGND –0.3 V to 4.2 V
RESET_X, SD, OTW to AGND –0.3 V to 7 V
Maximum continuous sink current (SD, OTW) 9 mA
Maximum operating junction temperature range, TJ 0°C to 125°C
Storage temperature –40°C to 125°C
Lead temperature, 1,6 mm (1/16 inch) from case for 10 seconds 260°C
Minimum pulse duration, low 30 ns
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) These voltages represent the dc voltage + peak ac waveform measured at the terminal of the device in all conditions.
ORDERING INFORMATION (1)

TA PACKAGE (1) DESCRIPTION
0°C to 70°C TAS5342ADDV 44-pin HTSSOP
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.

TAS5342A
Terminal Functions
TERMINAL (1)
FUNCTION DESCRIPTION
NAME DDV NO.
AGND 11 P Analog ground
BST_A 43 P Bootstrap pin, A-Side
BST_B 34 P Bootstrap pin, B-Side
BST_C 33 P Bootstrap pin, C-Side
BST_D 24 P Bootstrap pin, D-Side
GND 10 P Ground
GND_A 38 P Power ground for half-bridge A
GND_B 37 P Power ground for half-bridge B
GND_C 30 P Power ground for half-bridge C
GND_D 29 P Power ground for half-bridge D
GVDD_A 44 P Gate-drive voltage supply; A-Side
GVDD_B 1 P Gate-drive voltage supply; B-Side
GVDD_C 22 P Gate-drive voltage supply; C-Side
GVDD_D 23 P Gate-drive voltage supply; D-Side
M1 15 I Mode selection pin (LSB)
M2 14 I Mode selection pin
M3 13 I Mode selection pin (MSB)
NC 3, 4, 19, 20, 25, 42 – No connect. Pins may be grounded.
OC_ADJ 9 O Analog overcurrent programming pin
OTW 2 O Overtemperature warning signal, open-drain, active-low
OUT_A 39 O Output, half-bridge A
OUT_B 36 O Output, half-bridge B
OUT_C 31 O Output, half-bridge C
OUT_D 28 O Output, half-bridge D
PVDD_A 40, 41 P Power supply input for half-bridge A
PVDD_B 35 P Power supply input for half-bridge B
PVDD_C 32 P Power supply input for half-bridge C
PVDD_D 26, 27 P Power supply input for half-bridge D
PWM_A 6 I PWM Input signal for half-bridge A
PWM_B 8 I PWM Input signal for half-bridge B
PWM_C 16 I PWM Input signal for half-bridge C
PWM_D 18 I PWM Input signal for half-bridge D
RESET_AB 7 I Reset signal for half-bridge A and half-bridge B, active-low
RESET_CD 17 I Reset signal for half-bridge C and half-bridge D, active-low
SD 5 O Shutdown signal, open-drain, active-low
VDD 21 P Input power supply
VREG 12 P Internal voltage regulator
(1) I = input, O = output, P = power

TAS5342A
TYPICAL SYSTEM BLOCK DIAGRAM
OTW
System
Microcontroller SD
I2C
OTW
SD
TAS5518
BST_A
Bootstrap
BST_B Capacitors
VALID RESET_AB
RESET_CD
PWM_A
OUT_A
Left- 2nd-Order L-C
Input Output
Channel Output Filter
H-Bridge 1 H-Bridge 1
Output OUT_B for Each
PWM_B
Half-Bridge
2-Channel
H-Bridge
BTL Mode
PWM_C OUT_C
2nd-Order L-C
Right- Output
Output Filter
Channel H-Bridge 2
Input OUT_D for Each
Output H-Bridge 2 Half-Bridge
PWM_D
GVDD_A, B, C, D
PVDD_A, B, C, D
M1
GND_A, B, C, D
BST_C
Hardwire M2
Mode Bootstrap
OC_ADJ
Control Capacitors
AGND
BST_D
VREG
GND
VDD
M3
4 4 4
PVDD GVDD
PVDD Power VDD
31.5 V Supply Hardwire
VREG
System Decoupling Power Supply OC Limit
Power Decoupling
Supply
GND
GND
GVDD (12 V)/VDD (12 V)

12 V
VAC
B0047-02

TAS5342A
FUNCTIONAL BLOCK DIAGRAM
4 VDD
Under-
OTW voltage 4
Protection
Internal Pullup VREG VREG
Resistors to VREG
SD
Power
On
M1
Reset AGND
Protection
M2 and
I/O Logic
M3 Temp.
Sense GND
RESET_AB
Overload
RESET_CD Isense OC_ADJ
Protection
GVDD_D
BST_D
PVDD_D
PWM Gate
PWM_D Ctrl. Timing OUT_D
Rcv. Drive
BTL/PBTL−Configuration
Pulldown Resistor
GND_D
GVDD_C
BST_C
PVDD_C
PWM Gate
PWM_C Ctrl. Timing OUT_C
Rcv. Drive
Pulldown Resistor
GND_C
GVDD_B
BST_B
PVDD_B
PWM Gate
PWM_B Ctrl. Timing OUT_B
Rcv. Drive
Pulldown Resistor
GND_B
GVDD_A
BST_A
PVDD_A
PWM Gate
PWM_A Ctrl. Timing OUT_A
Rcv. Drive
Pulldown Resistor
GND_A
B0034-03

TAS5342A
RECOMMENDED OPERATING CONDITIONS

MIN TYP MAX UNIT
PVDD_X Half-bridge supply voltage 0 31.5 34 V
Supply voltage for logic regulators and
GVDD_X 10.8 12 13.2 V
gate-drive circuitry
VDD Digital regulator supply voltage 10.8 12 13.2 V
RL (BTL) 3 4
Resistive load impedance (no Cycle-by_Cycle
RL (SE) current control), recommended demodulation 2.25 3 Ω
filter
RL (PBTL) 1.5 2
LOutput (BTL) 5 10
Minimum output inductance under
LOutput (SE) Output-filter inductance 5 10 µH
short-circuit condition
LOutput (PBTL) 5 10
fS PWM frame rate 192 384 432 kHz
tLOW Minimum low-state pulse duration per PWM
30 nS
Frame, noise shaper enabled
CPVDD PVDD close decoupling capacitors 0.1 µF
CBST Bootstrap capacitor, selected value supports
33 nF
PWM frame rates from 192 kHz to 432 kHz
ROC Over-current programming resistor Resistor tolerance = 5% 27 27 47 kΩ
REXT-PULLUP External pull-up resistor to +3.3V to +5.0V for
3.3 4.7 kΩ
SD or OTW
TJ Junction temperature 0 125 °C
AUDIO SPECIFICATIONS (BTL)

Audio performance is recorded as a chipset consisting of a TAS5518 pwm processor (modulation index limited to 97.7%) and
a TAS5342A power stage. PCB and system configuraton are in accordance with recommended guidelines. Audio frequency =
1 kHz, PVDD_x = 31.5 V, GVDD_x = 12 V, RL = 4 Ω, fS = 384 kHz, ROC = 27 kΩ, TC = 75°C, Output Filter: LDEM = 10 µH,
CDEM = 470 nF, unless otherwise noted.
TAS5342A
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX
RL = 4 Ω, 10% THD+N, clipped input signal 100
POMAX Maximum Power Output RL = 6 Ω, 10% THD+N, clipped input signal 80
RL = 8 Ω, 10% THD+N, clipped input signal 65 W
RL = 4 Ω, 0 dBFS, unclipped input signal 80
PO Unclipped Power Output RL = 6 Ω, 0 dBFS, unclipped input signal 64
0 dBFS; AES17 filter 0.4%
THD+N Total harmonic distortion + noise
1 W; AES17 filter 0.09%
Vn Output integrated noise A-weighted, AES17 filter, Auto mute disabled 45 µV
(1)
SNR Signal-to-noise ratio A-weighted, AES17 filter, Auto mute disabled 110 dB
A-weighted, input level = –60 dBFS, AES17
DNR Dynamic range 110 dB
filter
DC Offset Output offset voltage ±15 mV
Pidle Power dissipation due to idle losses PO = 0 W, all halfbridges switching (2) 2 W
(IPVDD_X)
(1) SNR is calculated relative to 0-dBFS input level.

(2) Actual system idle losses are affected by core losses of output inductors.

TAS5342A
AUDIO SPECIFICATIONS (Single-Ended Output)

1 kHz, PVDD_x = 31.5 V, GVDD_x = 12 V, RL = 4 Ω, fS = 384 kHz, ROC = 27 kΩ, TC = 75°C, Output Filter: LDEM = 20 µH,
CDEM = 1.0 µF, unless otherwise noted.
TAS5342A
MIN TYP MAX
RL = 3 Ω, 10% THD+N, clipped input
40
signal
POMAX Maximum Power Output
RL = 4 Ω, 10% THD+N, clipped input
30 W
signal
PO Unclipped Power Output
Vn A-weighted, AES17 filter, Auto mute 35 µV
Output integrated noise
disabled
SNR A-weighted, AES17 filter, Auto mute 109 dB
Signal-to-noise ratio (1)
disabled
A-weighted, input level = –60 dBFS
AES17 filter
Pidle Power dissipation due to idle losses (IPVDD_X) PO = 0 W, all half bridges switching (2) 2 W

AUDIO SPECIFICATIONS (PBTL)

1kHz, PVDD_x = 31.5 V, GVDD_x = 12 V, RL = 3 Ω, fS = 384 kHz, ROC = 27 kΩ, TC = 75°C, Output Filter: LDEM = 10 µH, CDEM
= 1.0 uF, unless otherwise noted.
TAS5342A
MIN TYP MAX
POMAX Maximum Power Output
W
PO Unclipped Power Output
Vn Output integrated noise A-weighted, AES17 filter, Auto mute disabled 45 µV
SNR Signal-to-noise ratio (1) A-weighted, AES17 filter, Auto mute disabled 110 dB
A-weighted, input level = –60 dBFS AES17
filter
DC Offset Outuput offset voltage ±15 mV
Power dissipation due to idle losses (2)
Pidle PO = 0 W, all half bridges switching 2 W
(IPVDD_X)


TAS5342A
ELECTRICAL CHARACTERISTICS
PVDD_x = 31.5 V, GVDD_X = 12 V, VDD = 12 V, TC (Case temperature) = 25°C, fS = 384 kHz, unless otherwise specified.
TAS5342A
MIN TYP MAX
Internal Voltage Regulator and Current Consumption
Voltage regulator, only used as a
VREG VDD = 12 V 3 3.3 3.6 V
reference node
Operating, 50% duty cycle 7.2 17
IVDD VDD supply current mA
Idle, reset mode 5.54 11
50% duty cycle 8 16
IGVDD_X Gate supply current per half-bridge mA
Reset mode 1 1.8
50% duty cycle, with 10 uH and 470 nF output 16.3 25 mA
IPVDD_X Half-bridge idle current filter
Reset mode, no switching 465 558 µA
Output Stage MOSFETs
Drain-to-source resistance, Low
RDSon,LS TJ = 25°C, excludes metallization resistance, 80 89 mΩ
Side
Drain-to-source resistance, High
RDSon,HS TJ = 25°C, excludes metallization resistance, 80 89 mΩ
Side
I/O Protection
Undervoltage protection limit,
Vuvp,G 9.5 V
GVDD_X
Vuvp,hyst (1) Undervoltage protection limit, 250 mV
GVDD_X
BSTuvpF Puts device into RESET when BST 5.85 V
voltage falls below limit
BSTuvpR Brings device out of RESET when 7 V
BST voltage rises above limit
OTW (1) Overtemperature warning 115 125 135 °C
Temperature drop needed below
OTWHYST (1) OTW temp. for OTW to be inactive 25 °C
after the OTW event
OTE (1) Overtemperature error threshold 145 155 165 °C
OTE- OTE - OTW differential, temperature
30 °C
OTWdifferential (1) delta between OTW and OTE
OLPC Overload protection counter fS = 384 kHz 1.25 ms
Resistor—programmable, high-end,
IOC Overcurrent limit protection 10.1 A
ROC = 27 kΩ with 1 ms pulse
IOCT Overcurrent response time 150 ns
tACTIVITY Time for PWM activity detector to
Lack of transistion of any PWM input 13.2 µS
DETECTOR activite when no PWM is present
Connected when RESET is active to provide
Output pulldown current of each
IPD bootstrap capacitor charge. Not used in SE 3 mA
half-bridge
mode.
Static Digital Specifications
VIH High-level input voltage PWM_A, PWM_B, PWM_C, PWM_D, M1, 2 V
VIL Low-level input voltage M2, M3, RESET_AB, RESET_CD 0.8 V
ILeakage Input leakage current 100 µA
OTW/SHUTDOWN (SD)
Internal pullup resistance, OTW to
RINT_PU 20 26 32 kΩ
VREG, SD to VREG
Internal pullup resistor 3 3.3 3.6
VOH High-level output voltage V
External pullup of 4.7 kΩ to 5 V 4.5 5
(1) Specified by design

TAS5342A
ELECTRICAL CHARACTERISTICS (continued)

PVDD_x = 31.5 V, GVDD_X = 12 V, VDD = 12 V, TC (Case temperature) = 25°C, fS = 384 kHz, unless otherwise specified.
TAS5342A
MIN TYP MAX
VOL Low-level output voltage IO = 4 mA 0.2 0.4 V
FANOUT Device fanout OTW, SD No external pullup 30 Devices
TYPICAL CHARACTERISTICS, BTL CONFIGURATION

TOTAL HARMONIC DISTORTION + NOISE OUTPUT POWER
vs vs
OUTPUT POWER SUPPLY VOLTAGE
130
10 125
THD+N - Total Harmonic Distortion + Noise - %
TC = 75°C 120 TC = 75°C

115
5 THD+N at 10% THD+N at 10%
110
105
2 100
95
90
1 4Ω
4W 85
80
0.5 75
70
65
0.2 60
55
0.1 50
45
40
0.05 35
6W 30 6Ω
25
0.02 8W 20
15
0.01 10
8Ω
5
0.005 0
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
20m 100m 200m 1 2 5 10 20 50 100 200
PO - Output Power - W PVDD – Supply Voltage – V
Figure 1. Figure 2.
UNCLIPPED OUTPUT POWER SYSTEM EFFICIENCY

vs vs
SUPPLY VOLTAGE OUTPUT POWER
100 100
95 95
90 TC = 75°C
90
85 85
80 80
75 4W 75 6W 4W
70 70 8W
System Efficiency - %
65
65
60 60
55 55
50 6W
50
45
45
40 40
35 35
30 30
25 25
20 20
15 15 TC = 25°C
8W
10 10 THD+N at 10%
5 5
0 0
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 0 20 40 60 80 100 120 140 160 180 200 220 240
PO - Output Power - W
PVDD – Supply Voltage – V
Figure 3. Figure 4.

TAS5342A
TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued)
SYSTEM POWER LOSS SYSTEM OUTPUT POWER

vs vs
OUTPUT POWER CASE TEMPERATURE
30 150
28 TC = 25°C 140
4W
26 THD+N at 10% 130
24 120
22 6W
System Power Loss - W
110
System Output Power - W

20 100
18 90
16 4W
80
14 70
12 60
10 50
6W 8W
8 40
6 30
4 20 THD+N at 10%
8W
2 10
0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 10 20 30 40 50 60 70 80 90 100 110 120
PO - Output Power - W TC - Case Temperature - °C
Figure 5. Figure 6.
NOISE AMPLITUDE
vs
FREQUENCY
0
-10 Vref = 19.5 V
-20 TC = 75°C
-30
-40
Noise Amplitude - dBV
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
2k 4k 6k 8k 10k 12k 14k 16k 18k 20k 22k
f - Frequency - Hz
Figure 7.

TAS5342A
TYPICAL CHARACTERISTICS, SE CONFIGURATION

vs vs
10
48
TC = 75°C TC = 75°C
5 44
THD+N at 10% THD+N at 10%
40
2
36
1
32 4W
0.5 4W
28
0.2 24
0.1 20
16
0.05
12
8W
0.02 8 8W
0.01 4
0.005 0
20m 100m 200m 1 2 5 10 20 50 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
PO - Output Power - W PVDD - Supply Voltage - V
Figure 8. Figure 9.
OUTPUT POWER
vs
CASE TEMPERATURE
48
44
40
36 4W
32
28
24 8W
20
16
12
8
4 THD+N at 10%
0
10 20 30 40 50 60 70 80 90 100 110 120
TC - Case Temperature - °C
Figure 10.

TAS5342A
TYPICAL CHARACTERISTICS, PBTL CONFIGURATION

vs vs
10 240
TC = 75°C TC = 75°C
5 220
THD+N at 10% THD+N at 10%
8W 200
2
180 2W
1
160
0.5
140
3W
0.2 2W 120
0.1 100
4W
0.05 80
60
0.02 3W
40
0.01 4W 20 8W
0.005 0
20m 100m 200m 1 2 5 10 20 50 100 300 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
PO - Output Power - W PVDD - Supply Voltage - V
Figure 11. Figure 12.
SYSTEM OUTPUT POWER

vs
CASE TEMPERATURE
260
240
220
2W
System Output Power - W
200
180
160
3W
140
120
4W
100
80
60
40 8W
THD+N at 10%
20
0
10 20 30 40 50 60 70 80 90 100 110 120
TC - Case Temperature - °C
Figure 13.

TAS5342A
APPLICATION INFORMATION
PCB Material Recommendation

FR-4 Glass Epoxy material with 2 oz. (70 µm) is recommended for use with the TAS5342A. The use of this
material can provide for higher power output, improved thermal performance, and better EMI margin (due to
lower PCB trace inductance.
PVDD Capacitor Recommendation

The large capacitors used in conjunction with each full-birdge, are referred to as the PVDD Capacitors. These
capacitors should be selected for proper voltage margin and adequate capacitance to support the power
requirements. In practice, with a well designed system power supply, 1000 µF, 50-V will support more
applications. The PVDD capacitors should be low ESR type because they are used in a circuit associtated with
high-speed switching.
Decoupling Capacitor Recommendations

In order to design an amplifier that has robust performance, passes regulatory requirements, and exhibits good
audio performance, good quality decoupling capacitors should be used. In practice, X7R should be used in this
application.
The voltage of the decoupling capactors should be selected in accordance with good design practices.
Temperature, ripple current, and voltage overshoot must be considered. This fact is particularly true in the
selection of the 0.1µF that is placed on the power supply to each half-bridge. It must withstand the voltage
overshoot of the PWM switching, the heat generated by the amplifier during high power output, and the ripple
current created by high power power output. A minimum voltage rating of 50-V is required for use with a 31.5-V
power supply.
System Design Recommendations

The following schematics and PCB layouts illustrate "best practices" in the use of the TAS5342A.
GVDD (+12 V)
PVDD
2.2 W 2.2 W
3.3 W
470 µF
100 nF 100 nF 50 V 10 nF
50 V
TAS5342ADDV
GND GND
GVDD_B GVDD_A 10 µH GND
Microcontroller
OTW BST_A
33 nF 25 V 3.3 W
NC NC
I2C GND 1 nF
NC PVDD_A 50 V
GND 100 nF 10 nF
SD PVDD_A 50 V
100 nF 50 V
PWM1_P PWM_A OUT_A 50 V 470 nF
VALID RESET_AB GND_A
100 nF GND 10 nF
PWM1_M PWM_B GND_B GND 100 nF 50 V 1 nF 50 V
27 k 50 V 50 V GND
OC_ADJ OUT_B
GND PVDD_B 10 µH 3.3 W
GND 33 nF 25 V
AGND BST_B
VREG BST_C
33 nF 25V 10 µH 3.3 W
100 nF M3 PVDD_C
1 nF
M2 OUT_C 100 nF 50 V
GND 50 V 100 nF 10 nF
M1 GND_C 50 V
50 V
PWM2_P PWM_C GND_D
470 nF
RESET_CD OUT_D 10 nF
100 nF GND
PWM2_M PWM_D PVDD_D 100 nF 1 nF 50 V
50 V 50 V GND
50 V
NC PVDD_D
GND 3.3 W
TAS5508/18 NC NC 10 µH
0W GND
VDD BST_D
100 nF GVDD_C GVDD_D 33 nF 25 V PVDD
3.3 W
GND
470 µF
50 V 10 nF
100 nF 100 nF 50 V
2.2 W 2.2 W
GND GND
VDD (+12 V) GND GVDD (+12 V)
Figure 14. Typical Differential (2N) BTL Application With AD Modulation Filters

TAS5342A
GVDD (+12 V)
PVDD
2.2 W 2.2 W
3.3 W
470 µF
100 nF 100 nF 50 V 10 nF
50 V
TAS5342ADDV
GND GND
Microcontroller
OTW BST_A
33 nF 25 V 3.3 W
NC NC
I2C GND 1 nF
NC PVDD_A 50 V
GND 100 nF 10 nF
SD PVDD_A 50 V
100 nF 50 V
PWM1_P PWM_A OUT_A 50 V 470 nF
100 nF GND 10 nF
PWM_B GND_B GND 100 nF 50 V 1 nF 50 V
27 k 50 V 50 V GND
OC_ADJ OUT_B
GND PVDD_B 10 µH 3.3 W
GND 33 nF 25 V
AGND BST_B
VREG BST_C
33 nF 25V 10 µH 3.3 W
100 nF M3 PVDD_C
1 nF
M2 OUT_C 100 nF 50 V
GND 50 V 100 nF 10 nF
M1 GND_C 50 V
50 V
PWM2_P PWM_C GND_D
470 nF
RESET_CD OUT_D 10 nF
100 nF GND
PWM_D PVDD_D 100 nF 1 nF 50 V
50 V 50 V GND
50 V
NC PVDD_D
GND 3.3 W
0W GND
VDD BST_D
3.3 W
GND
470 µF
50 V 10 nF
100 nF 100 nF 50 V
2.2 W 2.2 W
GND GND
Figure 15. Typical Non-Differential (1N) BTL Application With AD Modulation Filters

TAS5342A
GVDD (+12V)
2
PVDD
1
2.2R 2.2R
3.3R
1
1
470uF
100nF
2
1
50V
100nF 10nF
2
50V
2
TAS5342ADDV
2
GND
1 44 GND
Microcontroller GVDD_B GVDD_A 20uH GND
2 43 1 2 1 2 A
OTW BST_A
3 42 33nF 25V
NC NC
I2C GND
4 41
GND NC PVDD_A
1
5 40
SD PVDD_A 100nF
PWM1_P 6 39 50V
PWM_A OUT_A
2
VALID 7 38
RESET_AB GND_A
GND
1
8 37
PWM2_P PWM_B GND_B
22k 100nF
1 2 9 36 50V
OC_ADJ OUT_B
2
10 35
GND PVDD_B
33nF 25V 20uH
GND
11 34 1 2 1 2
AGND BST_B B
1 2 12 33 1 2 1 2
VREG BST_C C
20uH
100nF 13 32 33nF 25V
M3 PVDD_C
1
14 31
M2 OUT_C
100nF
15 30 GND 50V
M1 GND_C
2
PWM3_P 16 29
PWM_C GND_D
1
17 28
RESET_CD OUT_D
100nF
PWM4_P 18 27 50V
PWM_D PVDD_D
2
19 26
NC PVDD_D
TAS5508/18 20 25
GND NC NC GND 20uH
0R
1 2 21 24 1 2 1 2
1
VDD BST_D D
22 23 33nF 25V
100nF GVDD_C GVDD_D
PVDD
2
1
3.3R
1
GND
470uF
1
1
2
50V
10nF
2
2
100nF 100nF 50V
2
2
2.2R 2.2R
1
GND GND GND

VDD (+12V) GVDD (+12V)
10nF 10nF
50V 50V
1 2 1 2
1
1
GND GND
3.3R 3.3R
2
2
A B
1
1
100nF 100nF
2
50V 50V
10k 1uF 10k 1uF
1 2
1 2
PVDD PVDD
1
2
1
470uF 10k 100nF GND 470uF 10k 100nF GND

50V 1% 50V 50V 1% 50V
1
2
2
2
1
1
470uF 10k 470uF 10k
50V 1% 3.3R 50V 1% 3.3R
2
1
2
1 2 1 2
GND GND
50V 50V
10nF GND 10nF GND
10nF 10nF
50V 50V
1 2 1 2
1
GND GND
3.3R 3.3R
2
C D
1
100nF 100nF
2
50V 50V
10k 1uF 10k 1uF
1 2
1 2
PVDD PVDD
1
2
1
470uF 10k 100nF GND 470uF 10k 100nF GND

50V 1% 50V 50V 1% 50V
1
2
2
2
1
470uF 10k 470uF 10k

50V 1% 50V 1%
3.3R 3.3R
2
1
2
1 2 1 2
GND GND
50V 50V
10nF GND 10nF GND
Figure 16. Typical SE Application

TAS5342A
GVDD (+12 V)
PVDD
2.2 W 2.2 W
3.3 W
470 µF
100 nF 100 nF 50 V 10 nF
50 V
TAS5342ADDV
GND GND
Microcontroller
OTW BST_A
33 nF 25 V
NC NC
I2C GND
NC PVDD_A
GND
SD PVDD_A
100 nF
PWM1_P PWM_A OUT_A
PWM_B GND_B GND 100 nF 3.3 W
PWM1_M
27 k 50 V 1 nF
OC_ADJ OUT_B 50 V
1R 100 nF 10 nF
GND PVDD_B 10 µH 50 V
GND 33 nF 25 V 50 V
AGND BST_B
1 µF
VREG BST_C
33 nF 25V 10 µH 100 nF 10 nF
100 nF M3 PVDD_C 50 V 1 nF 50 V
50 V GND
M2 OUT_C 100 nF
M1 GND_C GND 50 V 3.3 W
PWM_C GND_D
RESET_CD OUT_D
100 nF
PWM_D PVDD_D 50 V
NC PVDD_D
GND
0W GND
VDD BST_D
3.3 W
GND
470 µF
50 V 10 nF
100 nF 100 nF 50 V
2.2 W 2.2 W
GND GND
Figure 17. Typical Differential (2N) PBTL Application With AD Modulation Filters
GVDD (+12 V)
PVDD
2.2 W 2.2 W
3.3 W
470 µF
100 nF 100 nF 50 V 10 nF
50 V
TAS5342ADDV
GND GND
Microcontroller
OTW BST_A
33 nF 25 V
NC NC
I2C GND
NC PVDD_A
GND
SD PVDD_A
100 nF
PWM1_P PWM_A OUT_A 50 V
PWM_B GND_B GND 100 nF 3.3 W
PWM1_M
27 k 50 V 1 nF
OC_ADJ OUT_B 50 V
1R 100 nF 10 nF
GND PVDD_B 10 µH 50 V
GND 33 nF 25 V 50 V
AGND BST_B
1 µF
VREG BST_C
33 nF 25V 10 µH 100 nF 10 nF
100 nF M3 PVDD_C 50 V 1 nF 50 V
50 V GND
M2 OUT_C 100 nF
M1 GND_C GND 50 V 3.3 W
PWM_C GND_D
RESET_CD OUT_D
100 nF
PWM_D PVDD_D 50 V
NC PVDD_D
GND
0W GND
VDD BST_D
3.3 W
GND
470 µF
50 V 10 nF
100 nF 100 nF 50 V
2.2 W 2.2 W
GND GND
Figure 18. Typical Non-Differential (1N) PBTL Application

TAS5342A
THEORY OF OPERATION
Special attention should be paid to the power-stage

POWER SUPPLIES power supply; this includes component selection,
To facilitate system design, the TAS5342A needs PCB placement, and routing. As indicated, each
only a 12-V supply in addition to the (typical) 31.5-V half-bridge has independent power-stage supply pins
power-stage supply. An internal voltage regulator (PVDD_X). For optimal electrical performance, EMI
provides suitable voltage levels for the digital and compliance, and system reliability, it is important that
low-voltage analog circuitry. Additionally, all circuitry each PVDD_X pin is decoupled with a 100-nF
requiring a floating voltage supply, e.g., the high-side ceramic capacitor placed as close as possible to
gate drive, is accommodated by built-in bootstrap each supply pin. It is recommended to follow the PCB
circuitry requiring only an external capacitor for each layout of the TAS5342A reference design. For
half-bridge. additional information on recommended power supply
and required components, see the application
In order to provide outstanding electrical and diagrams given previously in this data sheet.
acoustical characteristics, the PWM signal path
including gate drive and output stage is designed as The 12-V supply should be from a low-noise,
identical, independent half-bridges. For this reason, low-output-impedance voltage regulator. Likewise, the
each half-bridge has separate gate drive supply 31.5-V power-stage supply is assumed to have low
(GVDD_X), bootstrap pins (BST_X), and power-stage output impedance and low noise. The power-supply
supply pins (PVDD_X). Furthermore, an additional pin sequence is not critical as facilitated by the internal
(VDD) is provided as supply for all common circuits. power-on-reset circuit. Moreover, the TAS5342A is
Although supplied from the same 12-V source, it is fully protected against erroneous power-stage turnon
highly recommended to separate GVDD_A, due to parasitic gate charging. Thus, voltage-supply
GVDD_B, GVDD_C, GVDD_D, and VDD on the ramp rates (dV/dt) are non-critical within the specified
printed-circuit board (PCB) by RC filters (see range (see the Recommended Operating Conditions
application diagram for details). These RC filters section of this data sheet).
provide the recommended high-frequency isolation.
Special attention should be paid to placing all SYSTEM POWER-UP/POWER-DOWN
decoupling capacitors as close to their associated SEQUENCE
pins as possible. In general, inductance between the
power supply pins and decoupling capacitors must be Powering Up
avoided. (See reference board documentation for
The TAS5342A does not require a power-up
additional information.)
sequence. The outputs of the H-bridges remain in a
For a properly functioning bootstrap circuit, a small high-impedance state until the gate-drive supply
ceramic capacitor must be connected from each voltage (GVDD_X) and VDD voltage are above the
bootstrap pin (BST_X) to the power-stage output pin undervoltage protection (UVP) voltage threshold (see
(OUT_X). When the power-stage output is low, the the Electrical Characteristics section of this data
bootstrap capacitor is charged through an internal sheet). Although not specifically required, it is
diode connected between the gate-drive power-- recommended to hold RESET_AB and RESET_CD in
supply pin (GVDD_X) and the bootstrap pin. When a low state while powering up the device. This allows
the power-stage output is high, the bootstrap an internal circuit to charge the external bootstrap
capacitor potential is shifted above the output capacitors by enabling a weak pulldown of the
potential and thus provides a suitable voltage supply half-bridge output.
for the high-side gate driver. In an application with
When the TAS5342A is being used with TI PWM
PWM switching frequencies in the range from 352
modulators such as the TAS5518, no special
kHz to 384 kHz, it is recommended to use 33-nF
attention to the state of RESET_AB and RESET_CD
ceramic capacitors, size 0603 or 0805, for the
is required, provided that the chipset is configured as
bootstrap supply. These 33-nF capacitors ensure
recommended.
sufficient energy storage, even during minimal PWM
duty cycles, to keep the high-side power stage FET
Powering Down
(LDMOS) fully turned on during the remaining part of
the PWM cycle. In an application running at a The TAS5342A does not require a power-down
reduced switching frequency, generally 192 kHz, the sequence. The device remains fully operational as
bootstrap capacitor might need to be increased in long as the gate-drive supply (GVDD_X) voltage and
value. VDD voltage are above the undervoltage protection
(UVP) voltage threshold (see the Electrical

TAS5342A
Characteristics section of this data sheet). Although signal using the system microcontroller and
not specifically required, it is a good practice to hold responding to an overtemperature warning signal by,
RESET_AB and RESET_CD low during power down, e.g., turning down the volume to prevent further
thus preventing audible artifacts including pops or heating of the device resulting in device shutdown
clicks. (OTE).
When the TAS5342A is being used with TI PWM To reduce external component count, an internal
modulators such as the TAS5518, no special pullup resistor to 3.3 V is provided on both SD and
attention to the state of RESET_AB and RESET_CD OTW outputs. Level compliance for 5-V logic can be
is required, provided that the chipset is configured as obtained by adding external pullup resistors to 5 V
recommended. (see the Electrical Characteristics section of this data
sheet for further specifications).
Mid Z Sequence Compatability
DEVICE PROTECTION SYSTEM
The TAS5342A is compatable with the Mid Z
sequence of the TAS5086 Modulator. The Mid Z The TAS5342A contains advanced protection circuitry
Sequence is a series of pulses that is generated by carefully designed to facilitate system integration and
the modulator. This sequence causes the power ease of use, as well as to safeguard the device from
stage to slowly enable its outputs as it begins to permanent failure due to a wide range of fault
switch. conditions such as short circuits, overload,
overtemperature, and undervoltage. The TAS5342A
By slowly starting the PWM switching, the impulse responds to a fault by immediately setting the power
response created by the onset of switching is stage in a high-impedance (Hi-Z) state and asserting
reduced. This impulse response is the acoustic the SD pin low. In situations other than overload and
artifact that is heard in the output transducers over-temperature error (OTE), the device
(loudspeakers) and is commonly termed "click" or automatically recovers when the fault condition has
"pop". been removed, i.e., the supply voltage has increased.
The low acoustic artifact noise of the TAS5342A will The device will function on errors, as shown in the
be further decreased when used in conjunction with following table.
the TAS5086 modulator with the Mid Z Sequence
enabled. BTL MODE PBTL MODE SE MODE
Local Local Local
The Mid Z sequence is primarily used for the Error Turns Off Error Turns Off Error Turns Off
single-ended output configuration. It facilitates a In In In
"softer" PWM output start after the split cap output A A A
configuration is charged. A+B A+B
B B A+B+C B
C C +D C
ERROR REPORTING C+D C+D
D D D
The SD and OTW pins are both active-low,
open-drain outputs. Their function is for Bootstrap UVP does not shutdown according to the
protection-mode signaling to a PWM controller or table, it shutsdown the respective halfbridge.
other system-control device.
Any fault resulting in device shutdown is signaled by Use of TAS5342A in High-Modulation-Index
the SD pin going low. Likewise, OTW goes low when Capable Systems
the device junction temperature exceeds 125°C (see This device requires at least 30 ns of low time on the
the following table). output per 384-kHz PWM frame rate in order to keep
SD OTW DESCRIPTION the bootstrap capacitors charged. As an example, if
the modulation index is set to 99.2% in the TAS5508,
Overtemperature (OTE) or overload (OLP) or
0 0
undervoltage (UVP) this setting allows PWM pulse durations down to 10
ns. This signal, which does not meet the 30-ns
0 1 Overload (OLP) or undervoltage (UVP)
requirement, is sent to the PWM_X pin and this
Junction temperature higher than 125°C low-state pulse time does not allow the bootstrap
1 0
(overtemperature warning)
capacitor to stay charged. The TAS5342A device
Junction temperature lower than 125°C and no requires limiting the TAS5508 modulation index to
1 1
OLP or UVP faults (normal operation)
97.7% to keep the bootstrap capacitor charged under
Note that asserting either RESET_AB or RESET_CD all signals and loads.
low forces the SD signal high, independent of faults The TAS5342A contains a bootstrap capacitor under
being present. TI recommends monitoring the OTW voltage protection circuit (BST_UVP) that monitors
the voltage on the bootstrap capacitors. When the

TAS5342A
voltage on the bootstrap capacitors is less than In general, it is recommended to follow closely the
required for proper control of the High-Side external component selection and PCB layout as
MOSFETs, the device will initiate bootstrap capacitor given in the Application section.
recharge sequences until the bootstrap capacitors are
properly charged for robust operation. This function For added flexibility, the OC threshold is
programmable within a limited range using a single
may be activated with PWM pulses less than 30 nS.
external resistor connected between the OC_ADJ pin
Therefore, TI strongly recommends using a TI PWM and AGND. (See the Electrical Characteristics section
processor, such as TAS5518, TAS5086 or TAS5508, of this data sheet for information on the correlation
with the modulation index set at 97.7% to interface between programming-resistor value and the OC
with TAS5342A. threshold.) It should be noted that a properly
functioning overcurrent detector assumes the
Overcurrent (OC) Protection With Current presence of a properly designed demodulation filter at
Limiting and Overload Detection the power-stage output. Short-circuit protection is not
provided directly at the output pins of the power stage
The device has independent, fast-reacting current
but only on the speaker terminals (after the
detectors with programmable trip threshold (OC
demodulation filter). It is required to follow certain
threshold) on all high-side and low-side power-stage
guidelines when selecting the OC threshold and an
FETs. See the following table for OC-adjust resistor
appropriate demodulation inductor:
values. The detector outputs are closely monitored by
two protection systems. The first protection system OC-Adjust Resistor Values Max. Current Before OC Occurs
controls the power stage in order to prevent the (kΩ) (A), TC=75°C
output current from further increasing, i.e., it performs 27 10.1
a current-limiting function rather than prematurely 33 9.1
shutting down during combinations of high-level 47 7.1
music transients and extreme speaker load
impedance drops. If the high-current situation The reported max peak current in the table above is
persists, i.e., the power stage is being overloaded, a measured with continuous current in 1 Ω, one
second protection system triggers a latching channel active and the other one muted.
shutdown, resulting in the power stage being set in
the high-impedance (Hi-Z) state. Current limiting and Pin-To-Pin Short Circuit Protection System
overload protection are independent for half-bridges (PPSC)
A and B and, respectively, C and D. That is, if the
bridge-tied load between half-bridges A and B causes The PPSC detection system protects the device from
an overload fault, only half-bridges A and B are shut permanent damage in the case that a power output
down. pin (OUT_X) is shorted to GND_X or PVDD_X. For
comparison the OC protection system detects an over
• For the lowest-cost bill of materials in terms of
current after the demodulation filter where PPSC
component selection, the OC threshold measure
detects shorts directly at the pin before the filter.
should be limited, considering the power output
PPSC detection is performed at startup i.e. when
requirement and minimum load impedance.
VDD is supplied, consequently a short to either
Higher-impedance loads require a lower OC
GND_X or PVDD_X after system startup will not
threshold.
activate the PPSC detection system. When PPSC
• The demodulation-filter inductor must retain at detection is activated by a short on the output, all half
least 5 µH of inductance at twice the OC threshold bridges are kept in a Hi-Z state until the short is
setting. removed, the device then continues the startup
Unfortunately, most inductors have decreasing sequence and starts switching. The detection is
inductance with increasing temperature and controlled globally by a two step sequence. The first
increasing current (saturation). To some degree, an step ensures that there are no shorts from OUT_X to
increase in temperature naturally occurs when GND_X, the second step tests that there are no
operating at high output currents, due to core losses shorts from OUT_X to PVDD_X. The total duration of
and the dc resistance of the inductor's copper this process is roughly proportional to the capacitance
winding. A thorough analysis of inductor saturation of the output LC filter. The typical duration is < 15
and thermal properties is strongly recommended. ms/µF. While the PPSC detection is in progress, SD
is kept low, and the device will not react to changes
Setting the OC threshold too low might cause issues applied to the RESET pins. If no shorts are present
such as lack of enough output power and/or the PPSC detection passes, and SD is released. A
unexpected shutdowns due to too-sensitive overload device reset will not start a new PPSC detection.
detection.

TAS5342A
PPSC detection is enabled in BTL and PBTL output VDD or GVDD_X pin results in all half-bridge outputs
configurations, the detection is not performed in SE immediately being set in the high-impedance (Hi-Z)
mode. To make sure not to trip the PPSC detection state and SD being asserted low. The device
system it is recommended not to insert resistive load automatically resumes operation when all supply
to GND_X or PVDD_X. voltages have increased above the UVP threshold.
Overtemperature Protection DEVICE RESET

The TAS5342A has a two-level Two reset pins are provided for independent control
temperature-protection system that asserts an of half-bridges A/B and C/D. When RESET_AB is
active-low warning signal (OTW) when the device asserted low, all four power-stage FETs in half--
junction temperature exceeds 125°C (nominal) and, if bridges A and B are forced into a high-impedance
the device junction temperature exceeds 155°C (Hi-Z) state. Likewise, asserting RESET_CD low
(nominal), the device is put into thermal shutdown, forces all four power-stage FETs in half-bridges C
resulting in all half-bridge outputs being set in the and D into a high-impedance state. Thus, both reset
high-impedance (Hi-Z) state and SD being asserted pins are well suited for hard-muting the power stage if
low. OTE is latched in this case. To clear the OTE needed.
latch, either RESET_AB or RESET_CD must be
asserted. Thereafter, the device resumes normal In BTL modes, to accommodate bootstrap charging
operation. prior to switching start, asserting the reset inputs low
enables weak pulldown of the half-bridge outputs. In
Undervoltage Protection (UVP) and Power-On the SE mode, the weak pulldowns are not enabled,
Reset (POR) and it is therefore recommended to ensure bootstrap
capacitor charging by providing a low pulse on the
The UVP and POR circuits of the TAS5342A fully PWM inputs when reset is asserted high.
protect the device in any power-up/down and
brownout situation. While powering up, the POR Asserting either reset input low removes any fault
circuit resets the overload circuit (OLP) and ensures information to be signalled on the SD output, i.e., SD
that all circuits are fully operational when the is forced high.
GVDD_X and VDD supply voltages reach stated in A rising-edge transition on either reset input allows
the Electrical Characteristics Table. Although the device to resume operation after an overload
GVDD_X and VDD are independently monitored, a fault. To ensure thermal reliability, the rising edge of
supply voltage drop below the UVP threshold on any reset must occur no sooner than 4ms after the falling
edge of SD.

PACKAGE MATERIALS INFORMATION
www.ti.com 22-Dec-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 (mm) B0 (mm) K0 (mm) P1 W Pin1
Type Drawing Diameter Width (mm) (mm) Quadrant
(mm) W1 (mm)
TAS5342ADDVR HTSSOP DDV 44 2000 330.0 24.4 8.6 15.6 1.8 12.0 24.0 Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 22-Dec-2008
*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TAS5342ADDVR HTSSOP DDV 44 2000 346.0 346.0 41.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Clocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrol
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
RFID www.ti-rfid.com Telephony www.ti.com/telephony
RF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated

TAS5342A

Uploaded by

Copyright:

Available Formats

TAS5342A

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TAS5342A

Uploaded by

Copyright:

Available Formats

TM

100 W STEREO DIGITAL AMPLIFIER POWER STAGE

• EMI Compliant When Used With 0

APPLICATIONS PurePath Digital™

• Mini/Micro Audio System

2 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A

Protection MODE Selection Pins

Package Heat Dissipation Ratings (1)

(1) JC is junction-to-case, CH is case-to-heatsink.

Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 3

ABSOLUTE MAXIMUM RATINGS

ORDERING INFORMATION (1)

4 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A

(1) I = input, O = output, P = power

Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 5

TYPICAL SYSTEM BLOCK DIAGRAM

GVDD (12 V)/VDD (12 V)

6 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A

FUNCTIONAL BLOCK DIAGRAM

Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 7

RECOMMENDED OPERATING CONDITIONS

AUDIO SPECIFICATIONS (BTL)

(1) SNR is calculated relative to 0-dBFS input level.

8 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A

AUDIO SPECIFICATIONS (Single-Ended Output)

(1) SNR is calculated relative to 0-dBFS input level.

AUDIO SPECIFICATIONS (PBTL)

(1) SNR is calculated relative to 0-dBFS input level.

Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 9

(1) Specified by design

10 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A

ELECTRICAL CHARACTERISTICS (continued)

TYPICAL CHARACTERISTICS, BTL CONFIGURATION

TC = 75°C 120 TC = 75°C

UNCLIPPED OUTPUT POWER SYSTEM EFFICIENCY

Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 11

TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued)

SYSTEM POWER LOSS SYSTEM OUTPUT POWER

System Output Power - W

12 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A

TYPICAL CHARACTERISTICS, SE CONFIGURATION

Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 13

TYPICAL CHARACTERISTICS, PBTL CONFIGURATION

Figure 11. Figure 12.

SYSTEM OUTPUT POWER

14 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A

PCB Material Recommendation

PVDD Capacitor Recommendation

Decoupling Capacitor Recommendations

System Design Recommendations

Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 15

16 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated

Product Folder Link(s): TAS5342A