Scribd Logo
Upload

Welcome to Scribd!

  • 69 views

    Pre-Energization Check List

    Uploaded by

    Mahmoud Hussein

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Pre-Energization Check List

    Uploaded by

    Mahmoud Hussein
    69 views2 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    69 views2 pages

    Pre-Energization Check List

    Uploaded by

    Mahmoud Hussein

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    200MW KOM OMBO S/S

    `
    Doc. No:
    Page NO: Pre-Energization CheckList
    DATE :

    Status Remark
    S. N Item
    Yes No N/A
    The categorization of punch list (A/B) is finalized, and all
    1.
    Type A snags of the subject equipment are cleared.
    2. All equipment are properly labeled.
    All tests results for the below equipment are signed by the
    T&C Contractor and Owner staff.
    3.1 AIS Equipments
    3.2 Power Transformers
    3.3 MV Switchgear
    3.4 Auxiliaries (AC & DC Panels, Batteries & Battery
    3. Chargers, Auxiliary Transformers, and UPS)
    3.5 SVG
    3.6 SAS (Open-loop test, and Close loop test)
    3.7 SCADA (Close-loop test of Conventional Substations)
    3.8 Under Ground Cables / Overhead Lines
    3.9 Protection Panels (including Final Trip Tests)
    3.10 Control Panels
    4.1 Repeated Punch List (if any)
    4.2 Scanned soft colored copy of marked up drawings
    4.3 Native files of the protection relays
    4. 4.4 Scanned soft colored copy of all site test results
    4.5 Original copy plus one soft copy of final settings
    review documents
    4.6 SAS handover documents
    CT Circuits Normalization :
    - Make sure that all CT circuits are connected, shorted,
    isolated, and single point earthed as per the marked-up
    5. drawings.
    - Ensure proper connections and tightness for all CT
    circuits by a screwdriver, and pull each wire gently to
    ensure that all CT wires terminated properly.
    VT Circuits Normalization :
    - Make sure that all VT circuits are connected, and
    isolated as per the marked-up drawings.
    6.
    - Ensure proper connections and tightness for all VT
    circuits by a screwdriver, and pull each wire gently to
    ensure that all VT wires terminated properly.
    Power Transformer & Outdoor Equipment :
    7.1 Ensure that there is no temporary grounding or
    shorting between phases of any transformer winding (high
    7. side, low side)
    7.2 Confirm that all covers of mechanical protection,
    outdoor boxes, and panels are properly closed, tighten,
    and sealed.
    200MW KOM OMBO S/S
    `
    Doc. No:
    Page NO: Pre-Energization CheckList
    DATE :

    7.3 Confirm that no oil leakage.

    7.4 Confirm that NER grounding is properly earthed.


    7.5 Confirm that there is no any temporary shorting
    across the primary terminals of the NER.

    7.6 On-load tap changer is set on the normal tap.

    Auxiliaries:
    - Confirm that there is no temporary shorting or grounding
    available at auxiliary transformer
    8. - Confirm that no oil leakage from the auxiliary
    transformer.
    - Tap changer of the auxiliary transformer is set on the
    normal tap.
    Alarms:
    9. - Make sure that there are no alarms on annunciators,
    relays, and SAS HMI (as applicable).

    You might also like