R2HH-6533A-R5

10-port sector/multibeam antenna, 2x 694–9 60 MHz 65° HPBW

and 8x 1710–2180 MHz 4x 33°HPBW, 5x RET with tilt indicators

Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connector
All Internal RET actuators are connected in “Cascaded SRET” configuration
Enhances network capacity through six sectors on high band while maintaining low band
coverage layer through three sectors with only three antenna faces

General Specifications
Antenna Type Multibeam

Band Multiband

Grounding Type RF connector inner conductor and body grounded to reflector and
mounting bracket

Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel
measurements described in white paper WP-112534-EN

Radome Material Fiberglass, UV resistant

Reflector Material Aluminum

RF Connector Interface 4.3-10 Female

RF Connector Location Bottom

RF Connector Quantity, high band 8

RF Connector Quantity, low band 2

RF Connector Quantity, total 10

Remote Electrical Tilt (RET) Information, General

RET Hardware CommRET v2

RET Interface 8-pin DIN Female | 8-pin DIN Male

RET Interface, quantity 1 female | 1 male

Dimensions
Width 350 mm | 13.78 in

Length 1580 mm | 62.205 in

Depth 208 mm | 8.189 in

Array Layout
Page 1 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: October 2, 2020
R2HH-6533A-R5

Port Configuration

Electrical Specifications
Impedance 50 ohm

Operating Frequency Band 1710 – 2180 MHz | 694 – 960 MHz

Polarization ±45°

Total Input Power, maximum 1,000 W @ 50 °C

Page 2 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: October 2, 2020
R2HH-6533A-R5
Remote Electrical Tilt (RET) Information, Electrical
Protocol 3GPP/AISG 2.0 (Single RET)

Power Consumption, idle state, maximum 1W

Power Consumption, normal conditions, maximum 8W

Input Voltage 10–30 Vdc

Internal RET High band (4) | Low band (1)

Electrical Specifications
Frequency Band, MHz 694–790 790–890 880–960 1710–1880 1850–1990 1920–2180
Gain, dBi 14.4 14.8 14.9 15.9 16.5 17.1
Beam Centers, Horizontal, ±27 ±27 ±27
degrees
Beamwidth, Horizontal, 69 67 65 33 32 30
degrees
Beamwidth, Vertical, degrees 13.5 12.3 11.5 11.9 11.2 10.6
Beam Tilt, degrees 2–14 2–14 2–14 2–14 2–14 2–14
USLS (First Lobe), dB 14 16 17 17 18 19
Front-to-Back Ratio at 180°, 32 34 33 31 34 35
dB
Isolation, Cross Polarization, 28 28 28 25 25 25
dB
Isolation, Inter-band, dB 30 30 30 25 25 25
Isolation, Beam to Beam, dB 17 17 17
VSWR | Return loss, dB 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5 1.46 | 14.5

PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C, 300 300 300 200 200 200
maximum, watts

Electrical Specifications, BASTA

Frequency Band, MHz 694–790 790–890 880–960 1710–1880 1850–1990 1920–2180
Gain by all Beam Tilts, 14.2 14.6 14.7 15.2 16 16.5
average, dBi
Gain by all Beam Tilts ±0.3 ±0.4 ±0.4 ±1 ±0.6 ±0.8
Tolerance, dB
Gain by Beam Tilt, average, 2 ° | 14.3 2 ° | 14.6 2 ° | 14.9 2 ° | 15.2 2 ° | 16.0 2 ° | 16.5
dBi 8 ° | 14.2 8 ° | 14.7 8 ° | 14.8 8 ° | 15.3 8 ° | 16.2 8 ° | 16.7
14 ° | 13.9 14 ° | 14.3 14 ° | 14.4 14 ° | 14.8 14 ° | 15.7 14 ° | 16.1

±1.9 ±2.3 ±2.2 ±1.7 ±1.7 ±1.7 Page 3 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: October 2, 2020
R2HH-6533A-R5
Beamwidth, Horizontal ±1.9 ±2.3 ±2.2 ±1.7 ±1.7 ±1.7
Tolerance, degrees
Beamwidth, Vertical ±1 ±0.8 ±0.7 ±1 ±0.9 ±0.9
Tolerance, degrees
USLS, beampeak to 20° above 14 16 16 17 18 18
beampeak, dB
Front-to-Back Total Power at 24 24 22 24 26 27
180° ± 30°, dB
CPR at Boresight, dB 16 16 17 14 15 16
CPR at Sector, dB 11 10 9
CPR at 10 dB Horizontal 8 11 11
Beamwidth, dB

Mechanical Specifications
Wind Loading at Velocity, frontal 254.0 N @ 150 km/h | 57.8 lbf @ 150 km/h

Wind Loading at Velocity, lateral 214.0 N @ 150 km/h | 48.1 lbf @ 150 km/h

Wind Loading at Velocity, maximum 121.2 lbf @ 150 km/h | 539.0 N @ 150 km/h

Wind Loading at Velocity, rear 269.0 N @ 150 km/h | 60.5 lbf @ 150 km/h

Wind Speed, maximum 241 km/h | 149.75 mph

Packaging and Weights

Width, packed 460 mm | 18.11 in

Depth, packed 372 mm | 14.646 in

Length, packed 1867 mm | 73.504 in

Net Weight, with installed actuator 25 kg | 55.115 lb

Weight, gross 38 kg | 83.776 lb

Regulatory Compliance/Certifications
Agency Classification
CHINA-ROHS Above maximum concentration value
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant/Exempted

Included Products
BSAMNT-3 Page 4 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: October 2, 2020
R2HH-6533A-R5
BSAMNT-3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

Page 5 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: October 2, 2020