SCOPE：

This specification applies to the Pb Free high current type SMD inductors for
MNR-6045-SERIES

PRODUCT INDENTIFICATION
MNR - 6045 - 150 M
① ② ③ ④

① Product Code
② Dimensions Code
③ Inductance Code
④ Tolerance Code

(1) SHAPES AND DIMENSIONS

A: 6.0±0.3 mm
B: 6.0±0.3 mm
C: 4.5 Max. mm
D: 3.10Typ. mm
E: 1.45Typ. mm

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1
TEST INSTRUMENTS
L : HP 4284A PRECISION LCR METER (or equivalent)
SRF : HP 4291B IMPEDANCE ANALYZER (or equivalent)
RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

(3) CHARACTERISTICS
(3)-1 Ambient temperature ……......... ＋60℃ Max.
(3)-2 Operate temperature range ...... －40℃～＋125℃
(Including self temp. rise)
(3)-3 Storage temperature range ...... －40℃～＋125℃

MAG.LAYERS

MNR-6045-SERIES Page 1/8

TABLE 1
MAGLAYERS Inductance Percent L Test SRF(MHz) Resistance Rated DC Current
Marking
PT/NO. L(μH) Tolerance Frequency Typ. RDC(Ω)±30% IDC1(A) IDC2(A)
MNR-6045-1R0□ 1.0 N 100KHz/0.25V 110 14m 8.50 4.20 1R0

MNR-6045-2R2□ 2.2 N 100KHz/0.25V 60 21m 6.00 3.50 2R2

MNR-6045-2R3□ 2.3 N 100KHz/0.25V 60 21m 6.00 3.50 2R3

MNR-6045-3R0□ 3.0 M,N 100KHz/0.25V 45 24m 5.00 3.20 3R0

MNR-6045-3R3□ 3.3 M,N 100KHz/0.25V 45 25m 4.80 3.10 3R3

MNR-6045-4R5□ 4.5 M,N 100KHz/0.25V 25 31m 4.00 3.00 4R5

MNR-6045-4R7□ 4.7 M,N 100KHz/0.25V 25 31m 4.00 3.00 4R7

MNR-6045-6R3□ 6.3 M,N 100KHz/0.25V 15 38m 3.80 2.80 6R3

MNR-6045-100□ 10 M,N 100KHz/0.25V 12 47m 3.00 2.50 100

MNR-6045-150□ 15 M,N 100KHz/0.25V 10 77m 2.30 1.90 150

MNR-6045-220□ 22 M,N 100KHz/0.25V 7 0.115 1.90 1.50 220

MNR-6045-470□ 47 M,N 100KHz/0.25V 5 0.220 1.30 1.10 470
MNR-6045-101□ 100 M,N 100KHz/0.25V 3 0.500 0.80 0.70 101

※ □ specify the inductance tolerance,M(±20%),N(±30%)

※ IDC1： Based on inductance change (△L/Lo： drop 30% Max.) @ ambient temp. 25℃
IDC2： Based on temperature rise (△T： 40℃ Typ.)
Rated DC Current： The less value whith is IDC1 or IDC2.

M A G .L A Y E R S
MNR-6045-SERIES Page-2/8
(4) RELIABILITY TEST METHOD
MECHANICAL
TEST ITEM SPECIFICATION TEST DETAILS
Substrate bending △L/Lo≦±5% The sample shall be soldered onto the printed circuit board
in figure 1 and a load applied unitil the figure in the arrow
There shall be direction is made approximately 3mm.(keep time 30 seconds)
no mechanical PCB dimension shall the page 7/9
damage or elec- F(Pressurization)
trical damege.

PRESSURE ROD
figure-1

Vibration △L/Lo≦±5% The sample shall be soldered onto the printed circuit board
and when a vibration having an amplitude of 1.52mm
There shall be and a frequency of from 10 to 55Hz/1 minute repeated should
no mechanical be applied to the 3 directions (X,Y,Z) for 2 hours each.
damage. (A total of 6 hours)

Solderability New solder Flux (rosin, isopropyl alcohol{JIS-K-1522}) shall be coated

More than 90% over the whole of the sample before hard, the sample shall
then be preheated for about 2 minutes in a temperature of
130～150℃ and after it has been immersed to a depth 0.5mm
below for 3±0.2 seconds fully in molten solder M705 with
a temperature of 245±5℃.
More than 90% of the electrode sections shall be couered
with new solder smoothly when the sample is taken out of
the solder bath.

MAG.LAYERS
MNR-6045-SERIES Page-3/8
MECHANICAL
TEST ITEM SPECIFICATION
Resistance to There shall be Temperature profile of reflow soldering
Soldering heat no damage or
(reflow soldering) problems. soldering

Sodering temperature (℃)

300
(Peak temperature 260±3℃ 10 sec
250

200
30 sec Min
(230+0 ℃)
150 Pre-heating
Slow cooling
100 150 ~ 180℃ (Stored at room
temperature)
50

10
2 min 2 min. or more
sec.

The specimen shall be passed through the reflow oven with the
condition shown in the above profile for 1 time.
The specimen shall be stored at standard atmospheric conditions
for 1 hour, after which the measurement shall be made.

ELECTRICAL
TEST ITEM SPECIFICATION TEST DETAILS
Insulation There shall be DC 100V voltage shall be applied across this sample of top
resistance no other surface and the terminal.
damage or The insulation resistance shall be more than 1 × 108 Ω.
problems.
Dielectric There shall be AC 100V voltage shall be applied for 1 minute acrosset the top
withstand no other surface and the terminal of this sample
voltage damage or
problems.
Temperature △L/L20℃≦±10% The test shall be performed after the sample has stabilized in
characteristics 0～2000 ppm/℃ an ambient temperature of -20 to +85℃,and the value
calculated based on the value applicable in a normal
temperature and narmal humidity shall be △L/L20℃≦±10%.

M AG.LAYERS
MNR-6045-SERIES Page-4/8
ENVIROMENT CHARACTERISTICS
TEST ITEM SPECIFICATION
High temperature △L/Lo≦±5% The sample shall be left for 96±4 hours in an atmospere with
storage a temperature of 85±2℃ and a normal humidity.
There shall be Upon completion of the measurement shall be made after the
no mechanical sample has been left in a normal temperature and normal
damage. humidity for 1 hour.

Low temperature △L/Lo≦±5% The sample shall be left for 96±4 hours in an atmosphere with
storage a temperature of -25±3℃.
There shall be Upon completion of the test, the measurement shall be made
no mechanical after the sample has been left in a normal temperature and
damage. normal humidity for 1 hour.
Change of △L/Lo≦±5% The sample shall be subject to 5 continuos cycles, such as shown
temperature in the table 2 below and then it shall be subjected to standard
There shall be atmospheric conditions for 1 hour, after which measurement
no other dama- shall be made.
ge of problems
table 2
Temperature Duration
－25±3℃
1 30 min.
(Themostat No.1)
Standard
2 No.1→No.2
atmospheric
85±2℃
3 30 min.
(Themostat No.2)
Standard
4 No.2→No.1
atmospheric

Moisture storage △L/Lo≦±5% The sample shall be left for 96±4 hours in a temperature of
40±2℃ and a humidity(RH) of 90～95%.
There shall be Upon completion of the test, the measurement shall be made
no mechanical after the sample has been left in a normal temperature and
damage. normal humidity more than 1 hour.
Test conditions：
The sample shall be reflow soldered onto the printed circuit board in every test.

MAG.LAYERS
MNR-6045-SERIES Page-5/8
(5) LAND DIMENSION (Ref.)

PCB: GLASS EPOXY t＝1.6mm

(5)-1 LAND PATTERN DIMENSIONS

(STANDARD PATTERN) unit：mm

(5)-2 SUBSTRATE BENDING TEST BENDING TEST BOARD

MAG.LAYERS
MNR-6045-SERIES Page-6/8
(6) PACKAGING
(6)-1 CARRIER TAPE DIMENSIONS (mm)
16

(6)-2 TAPING DIMENSIONS (mm)

Unreeling
Direction

MAG.LAYERS
MNR-6045-SERIES Page-7/8
(6)-3 REEL DIMENSIONS (mm)

Tape width:16

(6)-4 QUANTITY
1000pcs/Reel
The products are packaged so that no damage will be sustained.

MAG.LAYERS
MNR-6045-SERIES Page-8/8