HKD redundant

FLUSH ANCHOR
Technical Datasheet
Update: Jan-23
HKD Flush anchor
Everyday standard manual set flush anchor for redundant fastening applications

Anchor version Benefits

- Simple and well proven
HKD - Approved, tested and confirmed
(M6-M16) by everyday jobsite experience
- Reliable setting thanks to simple
visual check
- Versatile
HKD-woL - For medium-duty fastening with
(M6-M16) bolts or threaded rods
- Available in various materials and
sizes for maximized coverage of
possible applications
HKD-S(R)
(M6-M12)

HKD-E(R)
(M6-M12)

Base material Load conditions

Concrete Concrete Redundant Pre-stressed Static/ Fire

(non-cracked) (cracked) fastening hollow core quasi-static resistance
slabs

Other information

European CE Sprinkler Corrosion

Technical conformity approved resistance
Assessment

Approvals / certificates
Description Authority / Laboratory No. / date of issue
European Technical Assessment a) DIBt, Berlin ETA-06/0047 / 2016-02-08
Fire test report DIBt, Berlin ETA-06/0047 / 2016-02-08
Assessment report fire Warringtonfire WF 327804/A / 2013-07-10
a) All data given in this section according to ETA-06/0047, issue 2016-02-08.
Static and quasi-static resistance

All data in this section applies to:

- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Minimum base material thickness
- Concrete C20/25, fck,cube = 25 N/mm²
- Anchors in redundant fastening

Effective anchorage depth for static

Anchor size M6 M6 M8 M8 M8 M10 M10 M10 M12 M12 M16
Effective anchorage depth hef [mm] 25 30 25 30 40 25 30 40 25 50 65

Characteristic resistance

M10x25

M10x30

M10x40

M12x25

M12x50

M16x65
M6x25

M6x30

M8x25

M8x30

M8x40
Anchor size
Resistance, HKD / HKD-woL 2,0 - 3,0 5,0 5,0 4,0 5,0 7,5 4,0 9,0 16,0
all load HKD-S/ HKD-E FRk [kN] - 3,0 - 3,0 5,0 - 4,0 6,0 - 6,0 -
directions HKD-SR/ HKD-ER - 3,0 - 3,0 - - - 6,0 - 6,0 -

Design resistance
M10x25

M10x30

M10x40

M12x25

M12x50

M16x65
M6x25

M6x30

M8x25

M8x30

M8x40

Anchor size
Resistance, HKD / HKD-woL 1,3 - 2,0 2,8 3,3 2,2 3,3 5,0 2,7 6,0 10,7
all load HKD-S/ HKD-E FRd [kN] - 2,0 - 2,0 3,3 - 2,7 4,0 - 4,0 -
directions HKD-SR/ HKD-ER - 2,0 - 2,0 - - - 4,0 - 4,0 -

Recommended loads a)
M10x25

M10x30

M10x40

M12x25

M12x50

M16x65
M6x25

M6x30

M8x25

M8x30

M8x40

Anchor size
Resistance, HKD / HKD-woL 1,0 - 1,4 2,0 2,4 1,6 2,4 3,6 1,9 4,3 7,6
all load HKD-S/ HKD-E FRec [kN] - 1,4 - 1,4 2,4 - 1,9 2,9 - 2,9 -
directions HKD-SR/ HKD-ER - 1,4 - 1,4 - - - 2,9 - 2,9 -
a) With overall partial safety factor for action  = 1,4. The partial safety factors for action depend on the type of loading and shall be
taken from national regulations.
 Fire resistance

All data in this section applies to:

- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Steel failure
- Minimum base material thickness
- Concrete C 20/25 to C50/60
- Partial safety factor for resistance under fire exposure M,fi = 1,0 (in absence of other national regulations)

Effective anchorage depth for fire

Anchor size M6 M6 M8 M8 M8 M10 M10 M10 M12 M12 M16
Effective anchorage depth hef [mm] 25 30 25 30 40 25 30 40 25 50 65

Characteristic resistance

M10x25

M10x30

M10x40

M12x25

M12x50

M16x65
M6x25

M6x30

M8x25

M8x30

M8x40
Anchor size
Fire exposure R30
Resistance, HKD / HKD-woL 0,5 - 0,6 0,9 1,3 0,6 0,9 1,8 0,6 2,3 4,0
all load FRk,fi [kN]
directions HKD-SR/ HKD-ER - 0,5 - 0,9 - - - 1,8 - 2,3 -
Fire exposure R120
Resistance, HKD / HKD-woL 0,2 - 0,5 0,7 0,7 0,5 0,7 1,5 0,5 1,8 3,2
all load FRk,fi [kN]
directions HKD-SR/ HKD-ER - 0,3 - 0,7 - - - 1,5 - 1,8 -

Design resistance
M10x25

M10x30

M10x40

M12x25

M12x50

M16x65
M6x25

M6x30

M8x25

M8x30

M8x40

Anchor size
Fire exposure R30
Resistance, HKD / HKD-woL 0,5 - 0,6 0,9 1,3 0,6 0,9 1,8 0,6 2,3 4,0
all load FRd,fi [kN]
directions HKD-SR/ HKD-ER - 0,5 - 0,9 - - - 1,8 - 2,3 -
Fire exposure R120
Resistance, HKD / HKD-woL 0,2 - 0,5 0,7 0,7 0,5 0,7 1,5 0,5 1,8 3,2
all load FRd,fi [kN]
directions HKD-SR/ HKD-ER - 0,3 - 0,7 - - - 1,5 - 1,8 -
For more information about diffrent failure modes and fire resistance times please see the full ETA-06/0047 report.

Requirements for redundant fastening

The definition of redundant fastening according to Member States is given in EN 1992-4 and CEN/TR 17079. In
Absence of a definition by a Member State the following default values may be taken.
Minimum number of anchors per Maximum design load of action
Minimum number of fixing points
fixing point NSd per fixing point a)
3 1 2 kN
4 1 3kN
a) The value for maximum design load of actions per fastening point NSd is valid in general that means all fastening points are considered
in the design of the redundant structural system. The value NSd may be increased if the failure of one (=most unfavorable) fixing point
is taken into account in the design (serviceability and ultimate limit state) of the structural system e.g. suspended ceiling.
Materials

Mechanical properties
Anchor size M6 M8 M10 M10 M12
HKD / HKD-woL 570 570 570 570 640
Nominal tensile
HKD-S, HKD-E fuk [N/mm²] 560 560 510 510 -
strength
HKD-SR, HKD-ER 540 540 540 540 -
HKD / HKD-woL 460 460 460 480 510
Yield strength HKD-S, HKD-E fyk [N/mm²] 440 440 410 410 -
HKD-SR, HKD-ER 355 355 355 355 -
HKD / HKD-woL 20,7 26,7 32,7 60,1 105
Stressed cross-
HKD-S, HKD-E As [mm²]
section 20,9 26,1 28,8 58,7 -
HKD-SR, HKD-ER
HKD / HKD-woL 32,3 54,6 82,9 184 431
Moment of
HKD-S, HKD-E W [mm³]
resistance 50 79 110 264 -
HKD-SR, HKD-ER
Characteristic With 5.8 Gr. Steel 7,6 18,7 37,4 65,5 167
bending resistance HKD-SR M0Rk,s [Nm]
for rod or bolt 11 26 52 92 -
HKD-ER with A4-70

Material quality
Part Material
HKD / HKD-woL Cold formed steel-galvanized to ≥ 5 µm
Anchor body HKD-S, HKD-E Steel Fe/Zn5, galvanized to ≥ 5 µm
HKD-SR, HKD-ER Stainless steel, 1.4401, 1.4404, 1.4571 EN 10088-3:2014
HKD / HKD-woL Cold formed steel
Expansion plug HKD-S, HKD-E Cold formed steel
HKD-SR, HKD-ER Stainless steel, 1.4401, 1.4404, 1.4571 EN 10088-3:2014

Anchor dimensions of HKD, HKD-S, HKD-E, HKD-SR, HKD-ER

M10x25

M12x25

M10x30

M10x40

M12x50

M16x65
M6x25

M8x25

M6x30

M8x30

M8x40

Anchor size
Anchor length lG [mm] 25 30 25 30 40 25 30 40 25 50 65
Anchor diameter ⌀d1 [mm] 7,9 8 9,95 9,95 9,95 11,9 11,8 11,95 14,9 14,9 19,75
Plug diameter ⌀d2 [mm] 5,1 5 6,35 6,5 6,35 8,1 8,2 8,2 9,7 10,3 13,8
Plug length l1 [mm] 10 15 7 12 16 7 12 16 7,2 20 29

Anchor body Expansions plugs

Setting information

Setting details

M10x25a)

M10x30a)

M12x25a)
M8x25a)

M10x40

M12x50

M16x65
M8x40
M6x25

M6x30

M8x30
Anchor size
Effective anchorage depth hef [mm] 25 30 25 30 40 25 30 40 25 50 65
Nominal diameter of drill bit d0 [mm] 8 8 10 10 10 12 12 12 15 15 20
Thread diameter d [mm] 6 6 8 8 8 10 10 10 12 12 16
Depth of drill hole h1 [mm] 27 32 27 33 43 27 33 43 27 54 70
Diameter of clearance hole
df [mm] 7 7 9 9 9 12 12 12 14 14 18
in the fixture
Torque moment Tinst [mm] 4 4 8 8 8 15 15 15 35 35 60
ls,min [mm] 6 6 8 8 8 10 10 10 12 12 16
Screwing depth
ls,max [mm] 12 12,5 11,5 14,5 17,5 12 12,7 18 12 23,5 30,5
a) With anchor size M8x25, M10x25, M10x30 and M12x25 only threaded rod are to be used.

Installation equipment
M10x25

M12x25

M10x30

M10x40

M12x50

M16x65
M6x25

M8x25

M6x30

M8x30

M8x40

Anchor size
Rotary hammer for setting TE 2 – TE 16 TE16–TE50
Machine setting tool HSD-M
6x25/30 8x25/30 8x40 10x25/30 10x40 12x25 12x50 16x65
Hand setting tool HSD-G
Other tools Hammer, torque wrench, blow out pump
Setting parameters

M10x25a)

M10x30a)

M12x25a)
M8x25a)

M10x40

M12x50

M16x65
M6x25

M6x30

M8x30

M8x40
Anchor size
Minimum spacing and minimum edge distance for HKD / HKD-woL
Minimum thickness of
hmin [mm] 100 - 100 100 100 100 100 100 100 100 120
concrete member
smin [mm] 80 - 80 60 80 80 60 80 80 125 130
Minimum spacing
c≥ [mm] 140 - 140 105 140 140 105 140 140 175 230
cmin [mm] 100 - 100 80 140 100 80 140 100 175 230
Minimum edge distance
s≥ [mm] 150 - 150 120 80 150 120 80 150 125 130
Minimum thickness of concrete member for HKD / HKD-woL
Minimum thickness of
hmin [mm] 80 - 80 80 80 80 80 80 80 - -
concrete member
Minimum spacing smin [mm] 200 - 200 200 200 200 200 200 200 - -
Minimum edge distance cmin [mm] 150 - 150 150 150 150 150 150 150 - -
Minimum spacing and minimum edge distance for HKD–S(R) / HKD–S(R)
Minimum thickness of
hmin [mm] - 100 - 100 100 - 100 100 - 100 -
concrete member
Minimum spacing smin [mm] - 60 - 60 80 - 60 80 - 125 -
Minimum edge distance cmin [mm] - 105 - 105 140 - 105 140 - 175 -
Minimum thickness of concrete member for HKD–S(R) / HKD–S(R)
Minimum thickness of
hmin [mm] - 80 - 80 80 - 80 80 - - -
concrete member
Diameter of clearance hole
smin [mm] - 200 - 200 200 - 200 200 - - -
in the fixture
Torque moment cmin [mm] - 150 - 150 150 - 150 150 - - -
For spacing (edge distance) smaller than critical spacing (critical edge distance) the design loads have to be
reduced.
Setting instruction

*For detailed information on installation see instruction for use given with the package of the product.
Setting instruction
1. Drilling 2. Cleaning

3. Inserting the anchor 4. Setting tools

5. Inserting the tools 6. Inserting the tools

7. Attaching the belonging washer 8.

 Basic loading data for redundant fastening in prestresed hollow core slabs

All data in this section applies to:

- Correct anchor setting (See setting instruction)
- No edge distance and spacing influence
- Ratio core width/web thickness w/e ≤ 4,2
- Concrete C 30/37 to C50/56
- Data is according to ETA-06/0047

Characteristic resistance
Anchor size M6x25 M8x25 M10x25
Bottom flange thickness db [mm] ≥ 35 (30a)) ≥ 35 ≥ 40
Resistance, all load directions HKD / HKD-wol FRk [kN] 2 3 4
a) The anchor may be used in a flange thickness of 30 mm with the same resistance but the drill hole is not allowed to cut cavity

Design resistance
Anchor size M6x25 M8x25 M10x25
Bottom flange thickness db [mm] ≥ 35 (30a)) ≥ 35 ≥ 40
Resistance, all load directions HKD / HKD-wol FRd [kN] 1,3 2,0 2,2
a) The anchor may be used in a flange thickness of 30 mm with the same resistance but the drill hole is not allowed to cut cavity

Recommended loads b)
Anchor size M6x25 M8x25 M10x25
Bottom flange thickness db [mm] ≥ 35 (30a)) ≥ 35 ≥ 40
Resistance, all load directions HKD / HKD-wol FRec [kN] 1,0 1,4 1,6
a) The anchor may be used in a flange thickness of 30 mm with the same resistance but the drill hole is not allowed to cut cavity
b) With overall partial safety factor for action  = 1,4. The partial safety factors for action depend on the type of loading and shall be
taken from national regulations.

Requirements for redundant fastening

The definition of redundant fastening according to Member States is given in EN 1992-4 and CEN/TR 17079. In
Absence of a definition by a Member State the following default values may be taken.
Minimum number of anchors per Maximum design load of action
Minimum number of fixing points
fixing point NSd per fixing point a)
3 1 2 kN
4 1 3kN
a) The value for maximum design load of actions per fastening point NSd is valid in general that means all fastening points are considered
in the design of the redundant structural system. The value NSd may be increased if the failure of one (=most unfavorable) fixing point
is taken into account in the design (serviceability and ultimate limit state) of the structural system e.g. suspended ceiling.
Admissible anchor positions in precast pre-stressed hollow core slabs
Type HKD / HKD-wol
Core distance lc ≥ [mm] 100
Pre-stressing steel distance lp ≥ [mm] 100
Distance between anchor position
ap ≥ [mm] 50
and pre-stressed steel

Anchor spacing and edge distance

Type HKD / HKD-wol
Minimum edge distance cmin ≥ [mm] 200
Minimum anchor spacing smin ≥ [mm] 400
Minimum distance between anchor groups amin ≥ [mm] 400

c1, c2 edge distance

s1, s2 anchor spacing
a1, a2 distances between anchor groups
Setting instruction with the stop drill bit TE-CX-HKD only
1. Positioning pres-stressed steel 2. Marking pre-stressed steel position

3. Marking pre-stressed steel position 4. Drilling

5. Cleaning 6. Inserting the anchor

7. Setting tools 8. Inserting the tools

9. Inserting the tools 10. Attaching the belonging washer

11.