C50 Parameters

Download as pdf or txt
Download as pdf or txt
You are on page 1of 16

C50 Multi-parameters Monitor

Product Specifications

1) Monitor Type
Classified by Type
Electric shock protection
Externally powered Class-I equipment; continuous operation equipment
type
Defibrillation-proof
defibrillation resistant equipment with internal power supply.
applied parts
Electric shock protection Equipment with CF applied part (ECG, C.O. and IBP monitoring part) and
level BF applied parts (all other monitoring parts).
IP grade IPX1
Work mode Continuous operation equipment
IEC 60601-1 IEC 60601-1-8 IEC 60601-2-27 EN 1060-3 IEC 80601-2-30
Safety standards
IEC60601-2-34 IEC60601-2-49 ISO 80601-2-56 ISO 80601-2-61

2) Environmental Specifications
Item Specification

Ambient
Working 5℃~40℃
temperature
conditions
RH ≤93%
Product specification

Barometric
700hPa~1060hPa
pressure

Please protect the monitor against violent impact, vibration, rain and snow in
Transport transport. The monitor should be Transported in a well-ventilated room without corrosive
conditions gas (ambient temperature: -20 ℃ ~60 ℃ ; RH: ≤93%; Barometric pressure:
700hPa~1060hPa).

The monitor should be packed and stored in a well-ventilated room without corrosive gas
Storage conditions (ambient temperature: -20 ℃ ~60 ℃ ; RH: ≤93%; Barometric pressure:
700hPa~1060hPa).

3) Power Supply
Item Specification
AC input voltage 100~240V
AC input frequency 50Hz/60Hz
Power supply Powered either by built-in battery or external AC.
Input power 60VA
C80/50: Standard: 11.1V/2200mAh rechargeable lithium-ion battery, supplying power
for at least 2 consecutive hours in normal use once fully charged.
Optional: 11.1V 4400mAh rechargeable lithium-ion battery, supplying power
Built-in battery
for at least 4 consecutive hours in normal use once fully charged.
C86: Standard: 11.1V 4400mAh rechargeable lithium-ion battery, supplying power for
at least 4 consecutive hours in normal use once fully charged.
11.1V 4400mAh: At least 4 hours from depletion to 90% charge in normal use.
Charge time
11.1V/2200mA: At least 2 hours from depletion to 90% charge in normal use.
Defibrillation output +5V defibrillation synchronization signal during 100ms
Synchronization Max delay: ≤35ms; Pulse width: 100ms±10; Up/Down time≤1ms

Analog Output Bandwidth: 0.5-40Hz; Max delay: ≤35ms; error: ±5%;

4) General Specifications
Item Specification
Dimension C50: About 291.7mm×250 mm×146.5mm
Weight C50: About 3.3kg(with battery)
LCD specification C50: Size: 10.4 Inch
Pixel :800×600

5) ECG Specifications
Item Specification
Applicable standards: IEC 60601-2-27.
12-lead (R, L, F, N, C1, C2, C3, C4, C5, C6 or RA, LA, LL, RL, V1, V2, V3, V4,
Lead mode
V5, V6)
Method of leads I, II, III, aVR, aVL, aVF, V1, V2, V3, V4, V5, V6
Waveform 2 -channel
Lead mode 5-lead (R, L, F, N, C; or RA, LA, LL, RL, V)
Method of leads I, II, III, aVR, aVL, aVF, V
Product specification

Waveform 2 -channel
Lead mode 3-lead ( R, L, F; or RA, LA, LL)
Method of leads I, II, III
Waveform 1-channel
Load 1V, power frequency, differential-mode AC voltage for 10s without damage
Overload protection
(p-v)
Resp, lead
AC waveform:
disconnection
Current :<0.1µA;
detection and active
Frequency 64kHz, ±10%
noise control
Auto identify the type of ECG leads.
Amplitude (p-v RTI) 0.5mV~5mV
Width (adult) 70ms~120ms
Width (neonate/child) 40ms~120ms
QRS wave amplitude
and interval a) with amplitude (p-v RTI) not exceeding 0.15mV
Not respond to the (except in neonate/child mode); or
signals: b) with 10ms width (except in neonate/child mode) in
case of 1mV amplitude.
Triggering threshold
200µV (lead II)
level
Power frequency
>100µV(p-v)
voltage tolerance
Triangular wave
4mV
amplitude (p-v RTI)
QRS wave amplitude
0.5 mV
Drift tolerance (p-v RTI)
QRS wave width 100ms
QRS wave recurrence
80bpm
frequency
Adult 15~300bpm
HR measurement Neonate/child 15~350bpm
range and error ±1% or ±1bpm in both 3-lead, 5-lead and 12-lead mode,
Error
whichever is greater.
Adult 15bpm~300bpm
Alarm limit range
neonate/child 15bpm~350bpm
Alarm limit
±1bpm
resolution
Alarm limit error ±1bpm
Alarm start time for
asystole and high/low <10s
HR
Input signal amplitude ±5mV
Input dynamic range Rate (RTI) 320mV/s
DC offset voltage -300~+300mV
Product specification

Output signal change ±10%


Failure display
(attenuation prior to Maximum attenuation: 50%
display)
Input impedance Signal attenuation (0.67Hz~40Hz): ≤20%
System noise (p-v
<25µV
RTI)
Multi-channel
<5%
crosstalk

1.25mm/mV, 2.5mm/mV, 5.0mm/mV, 10mm/mV, 20mm/mV, 40mm/mV, Auto.


Manual replacement.
Plus ±750mV DC polarization voltage; sensitivity change range: ±5%.
Gain
Gain change per
≤0.66%/min
minute
Total gain change in
≤±10%
1h
Surgery mode:1 Hz~20 Hz (-3.0dB~+0.4dB);
Monitoring Mode:0.5 Hz~40 Hz (-3.0dB~+0.4dB);
bandwidth
Diagnosis mode:0.05Hz~150 Hz (-3.0dB~+0.4dB);
ST mode:0.05Hz~40Hz(-3.0dB~+0.4dB)
Permanent
25mm/s, 50 mm/s
display
Time reference Time reference
Non-
selection and selection
permanent 6.25mm/s, 12.5mm/s, 25 mm/s, 50 mm/s
accuracy
display
Maximum time
±10%
reference error
Channel width 30mm
Output display
Aspect ratio 0.4s/mV
Use method A and method B in IEC 60601-2-27to determine the total system error
and frequency response.
Total system error ±20% or ±100µV, whichever is larger.

Sinusoidal input 0.67~40Hz (attenuation: -3dB)


Input signal Frequency response
Response to 20ms
reconstruction 0~25Hz attenuation in amplitude of
(width) triangular
accuracy wave peak
wave
Response to 0.3mV·s Offset (RTI) ≤0.1mV
shock in the shock
range Slope (RTI) ≤0.30mV/s
Electrode weighting
≥±5%
factor
Product specification

Hysteresis effect of
≤0.5mm
15mm offset
Calibration voltage ±5% error at 1mV
Common mode
<1mV (p-v RTI)
rejection
Recovery time after
3s
reset
Baseline control and Drift rate in 10s 10µV/s
stability Baseline drift in 1h ≤500µV
Baseline drift at
≤50µV/℃
working temperature
Amplitude: ±2mV~±700mV; width: 0.1ms~2.0ms; if overshoot < 0.05ɑ p, settling
Non-overshoot
time < 5µs; start time, end time, rise time and fall time of pulse: ≤ 100µs; start time
pacemaker pulse
of pulse: 40ms or earlier before the start time of QRS wave; there is an identical
inhibition
pulse 150ms~250ms before the above pacemaker pulse.
Inhibition of
pacemaker pulse
Minimum input slew rate: 320mV/s RTI
detector on quick
ECG signals
Amplitude: ±2MV~±700MV; width:
Pacemaker pulse 0.5MS~2MS; maximum rise time:
≥0.2mV
display capability 100µS; the ECG display when the
pacemaker pulse appears at 100/min.
Measurement range -2.0mV-+2.0mV (-20.0 mm~+20.0 mm)
ST segment
-0.8mV~+0.8mV: ±0.02mV or ±10%, whichever is greater.
measurement Measurement error
Other ranges: not defined.
STalarm limit range -2.0mV-+2.0mV
ST alarm limit error ±0.1mV
Resolution 0.01mV (0.1mm)
Asystole, ventricular fibrillation (VFIB)/ventricular tachycardia (VTAC),
PVCs/min, R on T, VT>2, couplet, PVC, bigeminy, trigeminy, tachycardia
(TACHY),bradycardia (BRADY), supraventricular tachycardia (SVT), extreme
Arrhythmia types tachycardia, extreme bradycardia, missed beats, multiform PVC (multi. PVCs),
VTAC, nonsustained VT (nonsus. VTAC), ventricular rhythm, heart pause,
pause/min, irregular rhythm (irr. rhythm), ventricular bradycardia, atrial fibrillation,
pacemaker not captured (PNC), pacemaker not paced (PNP).
Leakage current <10uA
Electrosurgical
interference HR change caused by interference: ≤±10%
inhibition
Cut mode: 300W
ESU protection Condense mode: 100W
Recovery time: ≤10s

HR Calculation
Product specification

Tall T-wave rejection


1.2mV
capability
If all of the last 3 RR intervals are longer than 1200ms, the average of the last 4
HR calculation RR intervals is the HR. In other cases, the average of the last 12 RR intervals (with
the longest interval and shortest interval excluded) is the HR.
the HR is displayed as follows after the 20s stable segment:
Cardiotachometer (bigeminy): 80±1bpm
accuracy and response (slowly varying bigeminy): 60±1bpm
to arrhythmia (quickly varying bigeminy): 120±1bpm
(two-way contraction): 90±2bpm
Response time for HR the response time for a HR change, whether from 80bpm to 120bpm or from
changes 80bpm to 40bpm, is less than 10s.
the waveform:
1 - range: 10s
0.5 - range: 10s
Tachycardia alarm
2 - range: 10s
start time
1 - range: 10s
0.5 - range: 10s
2 - range: 10s
6) Resp Specifications
Item Specification
Method Thoracic impedance method

Measurem Adult 0rpm-120rpm


ent range Child/neonate 0rpm-150rpm
RR measurement range
and accuracy Measurem
7rpm~150rpm: ±2rpm or ±2%, whichever is greater. 0rpm~6rpm:
ent
not defined.
accuracy

Adult 0rpm~120rpm
RR alarm limit range and
Neonate/c
error 0rpm~150rpm
hild
Error ±1rpm
Adult: 110s、15s、20s、25s、30s、35s、40s、45s、50s、
No breath alarm limit Range 55s、1min
range and error Child/neonate: 10s、15s、20s、25s、30s、35s、40s
Error ±5s
No breath alarm delay 10s、15s、20s、25s、30s、35s、40s、45s、50s、55s、1min、Off
The Monitor will display the relevant alarm message when the HR is identical
CVA identification
with the RR.

7) SpO2 Specifications
Item Specification
Display range 0%~100%
Display resolution 1%
Product specification

Data averaging and other 2s


signal processing time
Data update time 8s
 Comen SpO2: measurement range: 0%~100%; measurement accuracy:
±2% (adult/child, in non-motion state) or ±3% (neonate, in non-motion
state) within the measurement range of 70%~100%. The measurement
accuracy within the measurement range of 1%~69% is not defined.
 Masimo SpO2: measurement range: 1%~100%; measurement accuracy:
±2% (adult/child, in non-motion state), ±3% (adult/child, in motion state)
Measurement accuracy or ±3% (neonate, in motion or non-motion state) within the measurement
range of 70%~100%. The measurement accuracy within the measurement
range of 1%~69% is not defined.
 Nellcor SpO2: measurement range: 0%~100%; measurement accuracy:
±2% (adult/child, in non-motion state) or ±3% (neonate, in non-motion
state) within the measurement range of 70%~100%. The measurement
accuracy within the measurement range of 0%~69% is not defined.
Comen SpO2:0%~100%
Alarm limit range and Range Masimo SpO2:1%~100%
accuracy Nellcor SpO2:20%~100%
Accuracy ±1%
Range for MasimoSpO2 and Comen SpO2: 0.02%~20%; accuracy: not defined.
Perfusion index (PI) Resolution: 0.01% (within 0.02%9.99% range) or 0.1% (within 10.0%20.0%
range).

8) PR Specifications
Item Specification
 Comen SpO2 sensor:
Measurement range: 20bpm~254bpm; resolution: 1bpm; measurement
error: ±2bpm.
 Masimo SpO2 sensor:
Measurement range: 25bpm~240bpm; resolution: 1bpm; measurement
error: ±3bpm (in non-motion state) or ±5bpm (in motion state).

Measurement range and  Nellcor SpO2 sensor:


accuracy Measurement range: 20bpm~300bpm; resolution: 1bpm; measurement
error: ±3bpm within 20bpm~250bpm range. The measurement accuracy
within 251bpm~300bpm range is not defined.
 NIBP sensor:
Measurement range: 40bpm~240bpm; resolution: 1bpm; measurement
error: ±3bpm or ±3%, whichever is greater.
 IBP sensor:
Product specification

Measurement range: 20bpm~350bpm; resolution: 1bpm; measurement


error within 20bpm~350bpm range: ±1bpm or ±1%, whichever is greater
(excluding the sensor error).
PR alarm limit range and 20bpm~350bmp
accuracy ±1bpm

9) Temp Specifications
Item Specification
Measurement range and Measurement range 0℃~50℃
accuracy Measurement error ±0.1℃(excluding the sensor error)
Temp alarm limit range Alarm limit range 0℃~50.0℃
and error Alarm limit error ±0.1℃
Resolution 0.1C
Number of channels 2
Operating mode Direct mode
Transient response No greater than 40 seconds

10) CO2 Specifications


Item Specification
The EtCO2 sensor complies with ISO 80601-2-55.
Masimo EtCO2 sensor (mainstream) Masimo EtCO2 sensor (sidestream)
CO2
0mmHg~190mmHg, 0~25% (at 0mmHg~190mmHg, 0~25% (at
measurement
760mmHg) 760mmHg)
range
CO2 resolution 1mmHg, 0.1kPa or 0.1% 1mmHg, 0.1kPa or 0.1%
0~15%: ±(0.2%+reading×2%) 0~15%: ±(0.2%+reading×2%)
CO2 accuracy
15~25%: not defined 15~25%: not defined
CO2 alarm limit
0~190mmHg 0~190mmHg
range
CO2 alarm
±0.1kPa or ±1mmHg ±0.1kPa or ±1mmHg
resolution
awRR
measurement 0~150rpm 0~150rpm
range
awRR
measurement ±1rpm ±1rpm
accuracy
awRR alarm
0rpm~150rpm 0rpm~150rpm
limit range
awRR alarm
1rmp 1rmp
resolution
No breath alarm Adult:10s、15s、20s、25s、30s、35s、
Range
limit range and 40s、45s、50s、55s、1min
Product specification

error Child/neonate: 20s、25s、30s、35s、40s

Error ±5s
No breathalarm
10s、15s、20s、25s、30s、35s、40s、45s、50s、55s、1min、Off
delay
Respironics/Nmed/Palconn EtCO2
Respironics/Nmed/Palconn EtCO2 sensor (mainstream)
sensor (sidestream)
CO2 0~150mmHg 0~150mmHg
measurement 0%~19.7% 0%~19.7%
range (0~20.0kPa) (0~20.0kPa)
0~69mmHg: 0.1mmHg 0~69mmHg: 0.1mmHg
CO2 resolution
70~150mmHg: 0.25mmHg 70~150mmHg: 0.25mmHg
0~40mmHg: ±2mmHg 0~40mmHg: ±2mmHg
41~70mmHg: ±5%×reading 41~70mmHg: ±5%×reading
CO2 accuracy
71~100mmHg: ±8%×reading 71~100mmHg: ±8%×reading
101~150mmHg: ±10%×reading 101~150mmHg: ±10%×reading
CO2 alarm limit
0~150mmHg 0~150mmHg
range
CO2 alarm
±0.1kPa or ±1mmHg ±0.1kPa or ±1mmHg
resolution
awRR
measurement 0~150rpm 0~150rpm
range
awRR
measurement ±1rpm ±1rpm
accuracy
awRR alarm
0~150rpm 0~150rpm
limit range
awRR alarm
1rmp 1rmp
resolution
Adult:10s、15s、20s、25s、30s、35s、
No breath alarm 40s、45s、50s、55s、1min
Range
limit range and Child/neonate: 10s 、 15s 、 20s 、 25s 、
error 30s、35s、40s
Error ±5s
No breathalarm
10s、15s、20s、25s、30s、35s、40s、45s、50s、55s、1min、Off
delay

11) NIBP Specifications


Item Specification
The NIBP sensor complies with IEC 80601-6-30.
Measurement method Auto oscillation method
Measurement range and Measurement range Systolic
5.3-36kPa (40-270mmHg)
accuracy (adult) pressure
Product specification

Diastolic
1.3-28.7kPa (10-215mmHg)
pressure
Mean
2.7-31.3kPa (20-235mmHg)
pressure
Systolic
5.3-26.7kPa (40-200mmHg)
pressure
Measurement range Diastolic
1.3-20kPa (10-150mmHg)
(child) pressure
Mean
2.7-22kPa (20-165mmHg)
pressure
Systolic
5.3-18kPa (40-135mmHg)
pressure
Measurement range Diastolic
1.3-13.3kPa (10-100mmHg)
(neonate) pressure
Mean
2.7-14.7kPa (20-110mmHg)
pressure
Measurement Maximum average deviation: ±5mmHg (±0.667kPa);
accuracy maximum standard deviation: ±8mmHg (±1.067kPa).
Adult mode 297mmHg
Overpressure protection Child mode 240mmHg
range and tolerance Neonate mode 147mmHg
Tolerance ±3mmHg
Systolic
5.3kPa~36kPa (40mmHg~270mmHg)
pressure
Diastolic
Adult 1.3kPa~28.7kPa (10 mmHg~215mmHg)
pressure
Mean
2.7kPa~31.3kPa (20mmHg~235mmHg)
pressure
Systolic
5.3kPa~26.7kPa (40mmHg~200mmHg)
pressure
Diastolic
Alarm limit range and Child 1.3kPa~20kPa (10mmHg~150mmHg)
pressure
error
Mean
2.7kPa~22kPa (20mmHg~165mmHg)
pressure
Systolic
5.3kPa~18kPa (40mmHg~135mmHg)
pressure
Neonat
Diastolic
e 1.3kPa~13.3kPa (10 mmHg~100mmHg)
pressure
Mean
2.7kPa~14.7kPa (20mmHg~110mmHg)
pressure
Error ±0.1kPa or ±1mmHg, whichever is greater.
Manual, auto (cyclic) or continual (not applicable to neonates)
1/2/2.5/3/4/5/10/15/30/60/90/120/180/240/480/720m
NIBP measurement mode Interval for auto mode
in
Continual 5min
Product specification

Initialpressurerange(mm
Adult:80~280;Child:80~210;Neonate:60~140
Hg)

12) IBP Specifications


Item Specification
Number of IBP channels 2
ART (arterial pressure), PA (pulmonary artery pressure), CVP (central venous
pressure), RAP (right atrial pressure), LAP (left atrial pressure), ICP
Pressure name (Intracranial pressure), AO (aortic pressure), UAP (umbilical artery pressure),
BAP (brachial artery pressure), FAP (femoral artery pressure), UVP (umbilical
venous pressure), LV (left ventricular pressure), P1, P2, P3 and P4..
ART 0~40kPa (0~300mmHg)
PA -0.8~16kPa (-6~120mmhg)
CVP -1.3~5.3kPa (-10~40mmHg)
RAP -1.3~5.3kPa (-10~40mmHg)
LAP -1.3~5.3kPa (-10~40mmHg)
ICP -1.3~5.3kPa (-10~40mmHg)
P1, P2 -6.6~40kPa (-50~300mmHg)
Measurement range and
P3, P4 -6.6~40kPa (-50~300mmHg)
accuracy
LV 0~40kPa (0~300mmHg)
AO 0~40kPa (0~300mmHg)
UAP 0~40kPa (0~300mmHg)
BAP 0~40kPa (0~300mmHg)
FAP 0~40kPa (0~300mmHg)
UVP -1.3~5.3kPa (-10~40mmHg)
IAP -1.3~5.3kPa (-10~40mmHg)
Static pressure
-1.3kPa~+40kPa(-50mmHg~+300mmHg)
measurement range
Display resolution for
static pressure 0.1kPa or 1mmHg
measurement
Static pressure
±1mmHg or ±2%, whichever is greater (excluding the sensor error).
measurement error
ART 0mmHg -300mmHg
PA -6mmHg~120mmHg
CVP -10mmHg~40mmHg
IBP alarm limit range RAP -10mmHg~40mmHg
LAP -10mmHg~40mmHg
ICP -10mmHg~40mmHg
P1 -50mmHg~300mmHg
Product specification

P2 -50mmHg~300mmHg
P3 -50mmHg~300mmHg
P4 -50mmHg~300mmHg
LV 0mmHg~300mmHg
AO 0mmHg~300mmHg
UAP 0mmHg~300mmHg
BAP 0mmHg~300mmHg
FAP 0mmHg~300mmHg
UVP -10mmHg~40mmHg
IAP -10mmHg~40mmHg
IBP alarm error ±0.1kPa or ±1mmHg
Sensitivity: 5V/V/mmHg
Pressure sensor
Impedance range: 300~3000Ω
Pressure zero calibration Each channel should feature a pressure zero calibration function, with an
accuracy of ± 1mmHg or ± 0.1kPa.)

13) C.O. Specifications


Item Specification
C.O.: 0~20L/min
C.O. measurement range BT: 25~43℃
IT: 0~25℃
C.O.: 0.1L/min
Resolution
BT, IT: 0.1℃
C.O.: ±5% or ±0.1L/min, whichever is greater.
Accuracy
BT, IT: ±0.1℃ (excluding the sensor)
Upper BT limit (lower limit + 0.4)~43℃
Upper and lower C.O.
Lower BT limit 25.0~(upper limit - 0.4)℃
alarm limit
Step size 0.1℃
Alarm accuracy ±0.1℃

14) AG Specifications
Item Specification
The AG module complies with ISO 80601-2-55.
AG measurement method Infrared radiation absorption characteristics

AG preheating time <20s


AG measurement range The accuracy of all measured values complies with EN ISO 21647:2004 and
Product specification

and accuracy EN 864:1996.

The following accuracy standards are applicable to a dry gas under 22±5°C and
1013±40hPa.

0%~15% ±(0.2kPa+reading×2%)
CO2
15%~25% Not defined.
N2O 0~100 % ±(2kPa+reading×2%)
0~8 % ±(0.15 %+reading×5%)
Hal, Enf, Iso
8~25 % Not defined.
0~10 % ±(0.15 %+reading×5%)
Sev
10~25 % Not defined.
0~22 % ±(0.15 %+reading×5%)
Des
22~25 % Not defined.
O2 0~100 % ±(1%+reading×2%)
RR 0~254rpm ±1rpm
CO2: 1mmHg
AG resolution
awRR: 1rpm
AG gas name
CO2, O2, N2O, one of the five anesthetic gases (Enf, Iso, Sev, Hal or Des)

Parameter Alarm Limit Accuracy

EtCO2 0mmHg~190mmHg ±1mmHg

Fi CO2 0mmHg~99mmHg ±1mmHg

AwRR 0rpm~150rpm ±1rpm

EtO2 0%~100% ±1%


AG alarm limit and
accuracy
FiO2 18%~100% ±1%

EtN2O 0%~100% ±1%

FiN2O 0%~82% ±1%

EtHal/EtEnf/EtIs
0%~25% ±0.1%
o/EtSev/EtDes

FiHal/FiEnf/FiIs
0%~25% ±0.1%
o/FiSev/FiDes

Item Specification
Specifications of ISATM (AG) Sidestream Gas Analyzer
Product specification

Measurement
Infrared gas measurement
method
For adult: 10s, 15s, 20s, 25s, 30s, 35s, 40s ,45s, 50s, 55s or 1min;
[No Breaths Range
For pediatric and neonate: 20s, 25s, 30s, 35s or 40s
Timeout]
Error ±5s
[No Breath
10s, 15s, 20s, 25s, 30s, 35s, 40s, 45s, 50s, 55s, 1min or Off
Alm Delay]
General Specifications
Ultra-small low-flow sidestream gas analyzer, with integrated micro-pump, zeroing valve
Description
and flow controller.
Working
ISA AX+: 0~50°C (32~122°F); ISA OR+: 5~50°C (41~122°F)
conditions
Storage
-40~70°C (-40~158°F)
conditions
RH <4kPa H2O (non-condensing) 95% RH, 30°C
Barometric
52.5~120kPa (4572m)
pressure
Water
Sampling tube: patented dehydration tube
treatment
Data Output
Fi/Et value CO2, O2, N2O, five anesthetic gases (Hal, Enf, Iso, Sev, Des)
Waveform Display up to 4 gas concentration waveforms at a time
Diagnostic
Barometric pressure
parameter
Gas Analyzer
ISA sensor 2~9-channel NDIR gas analyzer (measurement range: 4~10µm)
Compensation CO2 broadening effect
No calibration is required. The Monitor will auto perform zeroing when powered on and
Calibration
perform auto zeroing every 24h (ISACO2) or 8h (ISA AX+/OR+) subsequently.
Preheating time ISA CO2: <10s; ISA OR+/AX+: < 20s
Gas
Rise time CO2: ≤250ms; N2O: ≤ 350ms; anesthetic gases: ≤ 350ms; O2: ≤450ms
Overall system
<3s (2m sampling tube)
response time
Respiration
Self-adaptive threshold (minimum CO2 concentration change: 1 vol%)
detection
RR 0-150 breaths/min
Anesthetic gas Threshold of main anesthetic gases (ISA OR+/AX+): 0.15 vol%. The concentration of
threshold any identified anesthetic gas will be reported, even if it is lower than 0.15 vol%.

15) BIS Specifications


Item Specification
BIS: 0-100; accuracy: 1%.
BIS measurement range
SQI: 0-100%; accuracy: 1%.
and accuracy
EMG: 0~100dB; accuracy: 1%.
Product specification

ESR: 0~100%; accuracy: 1%.

Paramete
Alarm Limit Step Size
r
BIS alarm limit
BIS 0~100 1

16) ICG Specifications


Item Specification

ICG measurement method Indirect impedance cardiography measurement

HR: 40~250bpm
Measurement range SV: 5~250mL
C.O.:1.4~15L/min
SV: not defined.
Measurement accuracy HR: ±2bpm.
C.O: no defined.
SV: 0.1ml
Resolution HR: 1bpm
C.O: 0.1L/min
Alarm Limit Resolution
Upper limit: (lower limit +
0.1)~15.0L/min/m2
C.I. 0.1L/min/m2
ICG alarm limit and Lower limit: 1.4~(upper limit -
resolution 0.1)L/min/m2
Upper limit: (lower limit +
TFC 1)~150/KΩ 1KΩ
Lower limit: 5~(upper limit - 1)KΩ

17) Recording Specifications (optional component)


Item Specification

Recording paper width 50mm

Effective recording 48mm


width

Paper speed 25/50 mm/s

RT record time 8s, 16s, 32s or continual

Number of waveforms 3

Any alarm record? Yes

18) Alarm System


Product specification

Item Specification
The alarm system complies with IEC 60601-1-8.

You might also like