8

May 15, 2024 1:46:35 PM for Webgrabit 7 6 5 Uncontrolled If Printed 4 3 2 1

SPECIFICATIONS REV
NO
ZONE
ECO/CN
NO
REVISIONS DATE
CHANGE
BY
APPR
BY
M16 MALE END VIEW M12 FEMALE END VIEW M12 MALE END VIEW
WIRING DIAGRAM RATED CURRENT [A] 4.0 A 001 ALL
USS20
00043
NEW RELEASE 06/22/20 RH CPB

RATED VOLTAGE [V] CABLE ASSEMBLY 60V, CORDSET 250V 002 D5

USS20
00845
P2, YELLOW WAS BLUE. 08/07/20 RH CPB

P1 J1 TEMPERATURE RATING -40 C TO +80 C (-40 F TO +176 F) 003 ALL

USS22
00828
P1 LENGTH CHANGE FROM 0.5M TO 0.2M. 06/06/22 RH MUH
2 4
4 5 1 1 PROTECTION CLASS IP67 OR HIGHER
5 4 5 2 2
3 3
D 1 3 4 4 D
5 N/C 5
3 1 6
3 1
7 P2
2 8 1
7 6
8
2
2 3
4

P1 J1 P2 5

C 0.2 METERS 0.2 METERS C

YELLOW DESCRIPTION
LABEL
TEMPERATURE
& 2-SPEED J1

1
PART NUMBER LABEL

P1 2659615749
DESCRIPTION
LABEL

2
B
0.98"
RPM & PRESSURE P2 B
YELLOW
2X 0.18" YELLOW

0.2 METERS

NOTES:

1.BUILD PER CONSTRUCTION NOTES 2659603341.

A D
E CWP/AWS-02/8620-FC31

CWP/AWS-2/5-SM/FC-01
WARNING
EXPORT OF THIS DRAWING TO COUNTRIES
A
C OUTSIDE OF THE U. S. IS SUBJECT TO U. S.
CWP/AWS-02/5SA-08
EXPORT ADMINISTRATION REGULATIONS
B CWP/AWS-05TSM/FC-01
COPYRIGHT EPIROC DRILLING SOLUTIONS ALL RIGHTS RESERVED UNSPECIFIED TOLERANCES CHARACTERISTIC SYMBOL
O 1in DRAWN BY RITU P RAJ
A CWP/AWS-02GM-42
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET FABRICATION MACHINING STRAIGHTNESS DATE 06/22/20
LETTER EPIROC DRILLING SOLUTIONS INFORMATION, IS THE PROPERTY OF EPIROC DRILLING
DESIGNATOR PROCEDURE NO DIM (IN) TOL (IN) TOL (IN) FLATNESS CHECKED BY RUTHIE HAN
SOLUTIONS, AND IS GIVEN TO THE RECEIVER IN CONFIDENCE. DIM (IN)
THE ABOVE WELD PROCEDURES APPLY TO WELDING OF THIS THE RECEIVER BY RECEPTION AND RETENTION OF THE DRAW- UNDER 2 PL 3 PL O 5 1O 15 2O 25 mm DATE 06/22/20 DRILLING SOLUTIONS LOCATION: GARLAND, TEXAS
.06 ROUNDNESS
PART AS INDICATED BY THE "LETTER DESIGNATOR" IN 24 UNDER 24 .01 .005
THE TAIL OF THE WELD SYMBOL.
ING ACCEPTS THE DRAWING IN CONFIDENCE AND AGREES
(CIRCULARITY) ENG. APPVL. LUKE BENDER
"NOTE" WELD SYMBOLS WITHOUT A LETTER DESIGNATOR
WILL CONFORM TO EPIROC DRILLING SOLUTION
PROCEDURE CWP/AWS-02 SM/FC-01.
THAT, EXCEPT AS AUTHORIZED IN WRITING BY EPIROC
DRILLING SOLUTIONS, IT WILL (1) NOT USE THE DRAWING OR 24 TO 120 .09
24 & UP
ANGLES
.03
0
.005
30'
ANGULARITY
DATE
MFG. APPVL.
06/22/20
TITLE
CABLE
M16-M-ST TO DBL M12-M & M12-F
ANY COPY THEREOF OR THE CONFIDENTIAL OR TRADE SECRET
DOES NOT APPLY TO SUPPLIER OWNED DESIGNED PART
OR IF WELD SYMBOL IS NOT PRESENT ON THIS DRAWING. INFORMATION THEREIN; (2) NOT COPY THE DRAWING; (3) NOT 120 UP .12
UNSPECIFIED FILLETS PERPENDICULARITY
THIRD ANGLE PROJECTION DATE
AND RADII TO BE .03 (SQUARENESS)

D REF. NO.
STRUCTURAL WELDING MUST BE DONE BY WELDERS AND DISCLOSE TO OTHERS EITHER THE DRAWING OR THE CONFI-
FINISHED WEIGHT DWG.
NO. 2659615749 CR
PROCEDURES QUALIFIED IN ACCORDANCE WITH THE EPIROC DENTIAL OR TRADE SECRET INFORMATION THEREIN; AND (4)
UNLESS OTHERWISE SPECIFIED, PARALLELISM
SIZE
STRUCTURAL WELDING PROCEDURE CWP/AWS-02
UPON COMPLETION OF THE NEED TO RETAIN THE DRAWING, OR
AND THE AWS STRUCTURAL WELDING CODE ANSI/AWS D1.1 REMOVE ALL BURRS AND SHARP
COMM.
2659615749
POSITION

WELD PROCEDURES NTS 1OF 1

UPON DEMAND, RETURN THE DRAWING, ALL COPIES THEREOF,
CORNERS AND COUNTERSINK SCALE SH
AND ALL MATERIAL COPIED THEREFROM.
TAPPED HOLES TO BODY SIZE. CONCENTRICITY NO.

8 7 6 5 4 3 2 1