Scribd
Upload
220 views4 pages

Technical - Specification - APFC Panel

Uploaded by

applepc.online
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
220 views4 pages

Technical - Specification - APFC Panel

Uploaded by

applepc.online
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

TECHNICAL SPECIFICATION

Sl.No Description Qty UOM


1. Capacitor bank set (Outdoor Type) 1 Set
6.6KV 2000 KVAR , 3 Phase with HT APFC Panel
For controlling with all structures and isolators

A. SCOPE:

I. This Scope covers supply, installation, testing and commissioning of Capacitor


banks . The indoor APFC Panel of outdoor type three phase capacitor banks along
with all controls , switching devices and protection features are to be enclosed in a
sheet steel enclosure . The outdoor type capacitor bank shall be fitted on structures
, to be supplied with the equipment. All necessary civil works required for
installation of outdoor type capacitor banks are covered under this scope.
II. The equipment and it’s components covered under this specification shall comply
with all the latest applicable statutory rules, regulations and relevant IS.
III. Any other component , accessories , safety features not specifically stated in this
specification but necessary for trouble free and safe operation of the equipment
shall be deemed to be included .

B. SERVICE CONDITIONS:
 Maximum ambient temperature: 50 degree Celsius
 Relative humidity-95 percent
 Altitude upto 1000 meter above MSL.

C. STANDARDS:
 IS 13925 : Capacitor .
 IS 3156:Residual Voltage Transformer.
 IS 5553: Series Reactor
 Any other component as per relevant IS.
All IS/IEC shall be read with latest amendments in vogue on the date of technical bid
opening.
I. Technical particulars:
Sl.No Description Parameters
1. Rated output(KV AC) 6.6 KV
2. Maximum Service 7.2 KV
voltage
3. Conforming to IS IS-13925(with Latest amendments)
4. Frequency 50 Hz
5. No. Of Phase Three
6. Rated Output 2000 KVAR
7. Configuration 4X500KVAR
8. Installation Outdoor (including Civil work)
9. Discharge resistors Internally provided to discharge the capacitor
units to <50V within 300 seconds
10. System configuration To be installed at 6.6 KV Earthed System
11. Earthing Earthed
12. Operation HT APFC Panel
13. Capacitor <0.2 Watt/ KVAR
losses(dielectric)
14. Total losses including <0.2 Watt/ KVAR
accessories
15. Enclosure CRCA Sheet steel , IP 65 or better.
16. Fixing Vertical arrangement on steel frame.
17. Protection 6.6 KV HRC Fuses with Striker
18. Type of dielectric All Polypropylene
19. Termination Cubicle provided for cable entry with necessary
arrangement supply of ‘ Epoxy Moulded Termination Kit’

ENCLOSURE:
1. The APFC Panel shall have industrial CRCA enclosure of thickness not less than 2 mm ,free
standing and compact in size. Ground clearance of bottom most part of APFC Panel should not
be less than 150 mm .
2. Enclosure door shall be interlocked with main Isolator to deenergise capacitors before door
can be opened.
3. It shall have two separate earthing terminals on two diagonally opposite corner for earthing of
enclosure.
DESIGN FEATURES:
I. The APFC Controller automatically switches on/off , No of steps of capacitor banks by
continuously sensing and giving signal to switches devices to switch on/off , the capacitor
steps as per requirement to achieve power factor near unity.

II. The APFC Panel shall have :


(a) Power capacitor units.
(b) Vacuum Contactor
(c) Series Reactor for inrush current protection.
(d) Auto Manual selection.
(e) Residual Voltage Transformer.
(f) HRC fuses with striker
(g) Automatic Power factor controller
(h) Audio-visual indicator of various fault conditions.
(i) Off Load Isolator.
(j) Smooth Start/Stop sequence.
(k) Safety interlocks such as door interlocks with off load isolator & door locking
mechanism with special type keys.
(l) Adequately rated Potential and Current Transformer.
(m)Remote monitoring components
(n) Protective Relays
(o) Measuring devices.
(p) Cable entry outlets through going boxes.
(q) Insulated Busbar.

III. The APFC Panel shall be painted after suitable treatment with one coat anti-corrosive paint
and two coats of synthetic enamelled paint of approved shade.
IV. The capacitor bank should be supplied with interconnection between units of capacitor and
phase connection.
V. Capacitor units shall be provided with arrangement of discharge resistors for quick
discharge of the bank after the capacitor is disconnected from the supply source so as to
reduce residual voltage to less than 50 volts within five minutes of switching off.
VI. The Capacitor element shall be wound from high purity annealed Aluminium foil , low loss
capacitor paper and Polypropylene film (to have mixed dielectric of paper and
polypropylene film ), vacuum dried and impregnated under vacuum with non-toxic , non-
PCB oil to ensure uniform film distribution and high ionisation limit.the basic unit shall be
hermetically sealed in suitable container.
VII. Each capacitor element shall be provided with built in fuse so as to isolate thje
faulty element if it becomes defective . In addition to this easily replaceable HRC fuses of
well known standard and made preferably of striker PIN indicator type single phase
capacitor unit shall be provided.
VIII. Measuring instrument shall be provided:

 KWH Meter
 PF Meter
 KW Meter
 Ammeter, Voltmeter and Selector Switch.

IX. PROTECTIVE RELAYS : APFC shall have the following protection:


 Overvoltage protection Relay
 No Volt protection relay
 Unbalance protection Relay
 Overcurrent and Earth fault protection to cover the faults in the capacitor unit and
its controlling circuit breaker.
 Microprocessor based fast acting type APFC Relay.
Following documents must be uploaded at the time of bid submission:
 An attested copy of Type Test Report as per relevant IS from CPRI/NABL Accredited labs
/Govt Approved test house of the capacitor bank of same or higher voltage rating.
Following documents must be submitted at the time of supply:
 An attested copy of manufacturer’s test certificate covering all routine tests as per relevant
IS of all the offered Capacitor banks /capacitor, Series Reactor, RVT, Relays etc.
 Copy of GTP, GA drawing, circuit diagram etc. with each set of APFC Panel.

You might also like