Scribd Logo
Upload

Welcome to Scribd!

  • 8 views

    SKF 719 - 8 CE - HCP4AH Specification

    Uploaded by

    Dozer122

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    SKF 719 - 8 CE - HCP4AH Specification

    Uploaded by

    Dozer122
    8 views6 pages

    Original Title

    SKF 719_8 CE_HCP4AH Specification

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    8 views6 pages

    SKF 719 - 8 CE - HCP4AH Specification

    Uploaded by

    Dozer122

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    719/8 CE/HCP4AH

    Super-precision, high-speed E design, single row angular


    contact ball bearing suitable for direct oil-air lubrication
    These super-precision, high-speed, E design, single row angular contact ball
    bearings, with 15° or 18° contact angle, accommodate radial and axial loads
    acting simultaneously, where the axial load acts in one direction only. They are
    designed to accommodate very high speeds. Compared to the equivalent SKF B
    design high-speed bearings, have a slightly higher speed capability and can
    accommodate heavier loads. They have two lubrication holes in their outer rings.
    • Suitable for direct oil-air lubrication
    • Very high running accuracy
    • Accommodate very high speeds
    • Accommodate relatively high radial loads and large unilateral axial loads

    Overview

    Dimensions

    Bore diameter 8 mm

    Outside diameter 19 mm

    Width 6 mm

    Contact angle 15 °

    Performance Properties

    Basic dynamic load rating 1.74 kN Contact type Normal contact (two-point
    contact)
    Basic static load rating 0.61 kN
    Number of rows 1
    Attainable speed for grease lubrication 145 000 r/min
    Ring type One-piece inner and outer
    Attainable speed for oil-air lubrication 220 000 r/min rings

    Design High-speed E

    Universal matching bearing No

    Matched arrangement No

    Matched condition (axial Not applicable


    clearance/ preload)

    Tolerance class P4A

    Material, bearing Hybrid

    Coating Without

    Sealing Without

    Generated from www.skf.com on 2023-09-16 Page 1 of 6


    Lubricant None

    Special feature Suitable for direct oil-air


    lubrication

    Generated from www.skf.com on 2023-09-16 Page 2 of 6


    Technical Specification

    Universal matching bearing(s) No

    Dimensions

    d 8 mm Bore diameter

    D 19 mm Outside diameter

    B 6 mm Width
    d1 11.3 Shoulder diameter of inner ring (large side
    mm face)
    d2 10.76 Shoulder diameter of inner ring (small side
    mm face)
    D1 15.7 Shoulder diameter of outer ring (large side
    mm face)

    K 0.5 mm Diameter of lubrication hole


    C1 3.65 Distance from outer ring side face to
    mm lubrication groove / lubrication hole
    r1,2 min. 0.3 Chamfer dimension
    mm
    r3,4 min. Chamfer dimension
    0.15
    mm

    a 4.8 mm Distance from side face to pressure point

    Abutment dimensions

    da min. 10 mm Diameter of shaft abutment


    db min. 10 mm Diameter of shaft abutment
    Da max. 17 mm Diameter of housing abutment
    Db max. 18.2 mm Diameter of housing abutment
    ra max. 0.3 mm Radius of fillet
    rb max. 0.15 mm Radius of fillet

    Generated from www.skf.com on 2023-09-16 Page 3 of 6


    Calculation data

    Basic dynamic load rating C 1.74 kN

    Basic static load rating C0 0.61 kN

    Fatigue load limit Pu 0.019 kN

    Attainable speed for grease lubrication 145 000 r/min

    Attainable speed for oil-air lubrication 220 000 r/min

    Contact angle α 15 °

    Ball diameter Dw 3.175 mm

    Number of rows i 1

    Number of balls (per bearing) z 9

    Reference grease quantity (per bearing) Gref 0.09 cm

    Preload and stiffness (back-to-back, face-to-face)

    Preload, class A GA 9 N

    Axial stiffnes for preload A (sets of two brgs back to back or face to face) 9 N/µm

    Preload, class B GB 27 N

    Axial stiffness for preload B (sets of two brgs back-to-back or face-to-face) 14 N/µm

    Preload, class C GC 55 N

    Axial stiffness for preload C (sets of two brgs back-to-back or face-to-face) 20 N/µm

    Correction factors for preload calculation

    Correction factor dependent on bearing series and size f 1.02

    Correction factor dependent on contact angle f1 1

    Correction factor, preload class A f2A 1

    Correction factor, preload class B f2B 1.05

    Correction factor, preload class C f2C 1.09

    Correction factor for hybrid bearings fHC 1.01

    Factors for equivalent bearing load calculation

    Calculation factor for equivalent loads f0 6.9

    Generated from www.skf.com on 2023-09-16 Page 4 of 6


    Additional factors for equivalent loads Refer to Notes 1 and 2 below

    Mass

    Mass 0.006 kg

    Generated from www.skf.com on 2023-09-16 Page 5 of 6


    Terms and conditions
    By accessing and using this website / app owned and published by AB SKF (publ.) (556007-3495 ·
    Gothenburg) (“SKF”), you agree to the following terms and conditions:

    Warranty Disclaimer and Limitation of Liability


    Although every care has been taken to assure the accuracy of the information on this website / app, SKF provides this
    information "AS IS" and DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
    IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. You acknowledge that your
    use of this website / app is at your sole risk, that you assume full responsibility for all costs associated with use of this
    website / app, and that SKF shall not be liable for any direct, incidental, consequential, or indirect damages of any kind
    arising out of your access to, or use of the information or software made available on this website / app. Any warranties
    and representations in this website / app for SKF products or services that you purchase or use will be subject to the
    agreed upon terms and conditions in the contract for such product or service. Further, for non-SKF websites / apps that
    are referenced in our website / app or where a hyperlink appears, SKF makes no warranties concerning the accuracy or
    reliability of the information in these websites / apps and assumes no responsibility for material created or published by
    third parties contained therein. In addition, SKF does not warrant that this website / app or these other linked websites /
    apps are free from viruses or other harmful elements.

    Third Party Services


    When viewing YouTube content via the SKF website(s) (i.e. using YouTube API Services), you agree to be bound by the
    YouTube Terms of Service.

    Copyright
    Copyright in this website / app copyright of the information and software made available on this website / app rest with
    SKF or its licensors. All rights are reserved. All licensed material will reference the licensor that has granted SKF the right
    to use the material. The information and software made available on this website / app may not be reproduced,
    duplicated, copied, transferred, distributed, stored, modified, downloaded or otherwise exploited for any commercial use
    without the prior written approval of SKF. However, it may be reproduced, stored and downloaded for use by individuals
    without prior written approval of SKF. Under no circumstances may this information or software be supplied to third
    parties.
    This website /app includes certain images used under license from Shutterstock, Inc.

    Trademarks and Patents


    All trademarks, brand names, and corporate logos displayed on the website / app are the property of SKF or its licensors,
    and may not be used in any way without prior written approval by SKF. All licensed trademarks published on this website
    / app reference the licensor that has granted SKF the right to use the trademark. Access to this website / app does not
    grant to the user any license under any patents owned by or licensed to SKF.

    Changes
    SKF reserves the right to make changes or additions to this website / app at any time.

    Generated from www.skf.com on 2023-09-16 Page 6 of 6

    You might also like