Product This product is controlled and set by Tuya APP.

It can
realize remote open, staff access management,
Product Mounting Preparation 2 Function Parameter
Introduction abnormal message prompts, temporary visitors 1 Use self-tapping screws to fix the box to the wall through the mounting holes. 1 Download and install Tuya APP.
password, etc.
Quick Star t Guide 2

3
Remove the protective cap and install the antenna on the antenna terminal.
Open the cable hole for threading.
2

3
Turn on the permission of the APP to use bluetooth.

Open the APP's permission to use the

local area network and cellular network.
Item
Material
Parameter
ABS, aluminum alloy, toughened Glass

4 Be sure to ground the power supply, otherwise abnormal conditions may occur. 2:24
Working Voltage\Cur rent DC12V±10%\2A(Non-loaded)
4 Create a family to better manage devices. Processor High-performance dual-core ARM chip /ISP/NPU
Communication Mode WiFi/Bluetooth
Product Appearance Antenna Recognition Speed <0.5s
JACK
Users 500
86-13512345678
3 Protective Cap Please search for "Smart Life" in the APP Verification Type Card/Password/Card+Password
Antenna store, download and install, or scan the QR Temporar y Code 10
Power 4 code below to download and install directly. Third-Party Voice Services More Password suppor t digits 6Bit
166mm 50mm IN:AC90~260V/50~60Hz
Lamp Panel OUT:DC12V/3A Lock Control Output 1
Alar m Output 1
Alexa Google SmartThings
Assistant Temper Switch 1
Exit Button 1
Door Magnet Input 1
Home Management 4 Working Environment -20℃-60℃ /10%-90%
2
I P Grade IP53
Message Center Install Type Wall

214mm
Size L214XW166XH50mm
Smart Life FAQ & Feedback

Homekit Information
107*92*20mm
1

Access Control
Note: The interface used in this
Tuya Smart Access Control Temper Switch
manual is for illustration only,
Home Scene Smart Me

please refer to Tuya APP.

Statement 3 Packing List 4 The Interface Definition 5 Wiring of Access Control Function
To the maximum extent permitted by law, the products described in this manual (including hardware, software,
firmware, etc.) are provided as they are. There may be defects, errors, or malfunctions. This manual is for
guidance only. The graphics, icons, and illustrations provided in the manual are for explanation and illustration

Power
Antenna V+

N L
only. There maybe differences with specific products, please refer to the actual product. The company does not
provide any form of express or implied guarantee, including but not limited to guarantees of marketability,
V- GND INPUT： L OUTPUT：
quality satisfaction, suitability for specifice purposes, and non-infringement of third-party rights, nor does
it prodive any special guarantees caused by the use of this manual or the company’s products. Incidental, NO DC 12V N AC 90~260V
incidental or indirect damgaes, including but not limited to loss of businiess profits, loss of data or documents.
If you connect products to the internet, you need to bear your own risks, incuding but not limited to, the product COM 3A 50/60Hz
may suffer from hacker attacks, virus infections, network attacks, data leakage, etc. The company does not
BOX×1 Access Controller×1 NC
assume any major or related responsibility for product failure, abnormality, information leakage and other is
sues caused by this. However, the company will provide users with product-related technical support.
When you use this product, you will collect, store, and use important personal information. As the data controller,
Lock
when collecting, storing, and using personal information, please follow the relevant laws and regulations
applicable to the protection of personal privacy. The company is not responsible for all personal and property
losses caused by misuse of personal data.
Danger of strong
The company’s products have encrypted personal biometric information. Its characteristic value cannot be
restored to an image.
Description of indicator lights and sound prompts
electricity!
Please observe the laws and regulations of the place of use when using the product. If this product is used to LED Relay2 Name Status Caption
infringe the rights of a third party or other improper purposes, the company will not bear any responsibility. War ning： Light Normal power supply
If the content of this manual conficts with applicable laws, the legal provisions shall prevail. Interface
N L

Power Supply×1 Quick Start Guide×1 ● Please do not use the power supply that comes with this product to power the lock. Flashing red Searching the internet
Tamper It is attendance only.
Relay1 Flashing blue
Network search successful, waiting
Switch ● Please do not connect the wires when the power is on. for binding
Green light is
● Please strictly comply with the national and regional electrical safety regulations. Binding succeeded Black
always on

● If you have any problem with the product, please contact the device seller. Flashing Equipment Run Red
Do not disassemble or modify this product without permission. Read the card or password or unbind Green
Light once successfully. White

For More Help Tapping Screw×4

Rubber Stopper×4 Antenna×1

Note：
● Please read this manual carefully before starting the installation.
Light once
Light once
Relay 1 action
Relay 2 action
If need a sound prompt, please
connect blue and yellow
A short beep APP operation is successful
Key×1 ● The distance from the card reader to the controller should not exceed 60 meters.
A long beep Valid, allowed to pass
⑴
● Be sure to install the ground wire of the power supply. Sound
Two short beeps Invalid, not allowed to pass
● Avoid damp, strong electromagnetic environment, outdoor bare leakage places. Three short beeps Unbind and clear data successfully

Lamp Panel×1 Light board cable×1 Temper Switch Black

Sound ⑴ :This function requires the use GND Red
of a card reader, please connect the BUZ
Door-Magnet Green
port of the controller to the indicator light White
and sound controller line of the card reader. If need a sound prompt, please
The product picture is for reference, if any
Temper Switch

Exit Button
Door-Magnet

Power connect blue and yellow

difference, please refer to the actual
product.
Exit Button
 3 When the CON light of the device is flashing Select the WIFI that will be used. Note: The Log in to WIFI and wait for binding. Binding succeeded. Finish adding.
6 Add Device blue, the APP will automatically search for the
device.
4
WIFI used must be the same as the WIFI used
by the mobile phone.
6 7 8

9 A good name for the device can be better managed.

7 Remove device
5 Fill in the WIFI login password. 2 "Remove device" in this interface is to 3 Click the Device Information button in the 4 "Remove device" in this interface is to
1 Click the icon in the lower left corner of the screen to 1 Click the device in the device list to delete the device from the device list and upper right corner of this interface. unbind, and the unbound device can be
enter "Home". enter the "A" interface. Long press no longer control and use it. But the device bound and used by other users. Please
2 Users can manually add devices in these two places the device to enter the "B" interface. has not been unbound. Cannot be bound by note the distinction.
on the "Home" page.
other users.

2:24 2:24
2:24 2:24 2:24 2:24 2:24 2:24 2:24

2 Cancel
Found 1devices，Added 0 successfully Found 1devices，Added 1 successfully

Added
8 Done
A 1 Selected
Done
B Smart Access Control
3
Smart Access Control
All Devices
Choose Wi-Fi and enter password
Smart Access Control
Smart Access Control Smart Access Control
WIFI-AA 4 Smart Access Control
9
6 7
Device added successfully
1 Device Information

5 Tap-to-Run and Automation

Device Offline Notification

No devices

Offline Notification
Add Device 2 Add Device
Press to unlock

Others

Share Device

Access control1
Create Group
Closed

Device to be added：1
FAQ & Feedback

Add to Home Screen

3
Check Device Nerwork Check Now

Smart Access
Control 03/14 14:25 A OpenAccess control1 2 Device Upadte No updates available

Next
Add Remove Device 4
1 Home Scene Smart Me Home Scene Smart Me Remove Device
2 User Add temporary
code
Attendance Setting

8 Setting Device Parameter 9 Remote control 10 Add User & Card

1 Click the "Setting" interface to set some parameters of the device. 1 Click the circular icon to open the door remotely. The device needs to match the key
1 Click the "User" button on the device interface 2 Click the "+" button to add a new person. 3 Enter the basic information of the personnel, 4 Click "Add Card" to add a card to the person. 5 With the card ready, click "Start Add". 6 After swiping the card within the specified 7 Add complete.
when using it for the first time. If it fails, please try again. to enter the personnel management interface.
2 When an exception occurs when the device is used for the first time, please turn and go to "Next" after completion. time, the RDOK indicator will light up once
on "Multiple Verification". Then use "Select unlock mode" in "Unlock by single the card is swiped.
mode" and then turn off "Multiple
Verification". If the door cannot be
closed automatically, please turn 2:24 2:24 2:24 2:24 2:24 2:24 2:24 2:24 2:24
on "Automatic lock" and set the "
Auto lock Time 3s". Setting Smart Access Control Smart Access Control Member
2 Cancel Add user Next step Delete u ... Cancel Add card

Door keep open user Name/account How to add the card

User name
3 A Put card on recognition area as shown in the figure.Do not remove the
card until the lock indicates that the card is added. If the card is not add
in 30s,the card fails to be added
Administrator Ordinary member
Remote unlock setting
2 This icon is displayed to indicate Country/area Add success
Permission settings Permission all that the door is open. A For other functions, please
A Owner
2:24
86-13512345678
86-13512345678 refer to Tuya APP. Please
Card name
Smart Access Control User account 135123456789
Administrator take Tuya APP as allow.
Passage set 0 0 0 0 0
2 Card1

Automatic lock Face

Administrator

Auto lock time 2s Press to unlock Press to lock Press to unlock

Add
Administrators can manage devices and members,but
2 1 2 members can only read unlock & alarm records
Multiple verification
Unlock only by group mode if switch on Fingerprint
56s

Keep card at given time and sensing area till

Access control1 Access control1 Access control1
Press to unlock
Open speed Open speed state low Add feedback done.
Closed Open Closed

Open rate 0%
Code 6
Access control1
Alarm time
Closed
Add

Ringtone Ringtone sound 1

Card
Doorbell volume Doorbell volume mute
03/14 14:25 A OpenAccess control1 2
3 03/14 14:25 A OpenAccess control1 2
Add
4
Language English 5
03/14 14:25 A OpenAccess control1 2
1
Telecontrol
3 Access and usage records can
User Add temporary Attendance Setting
1 User Add temporary
code
Attendance Setting
be found here. User Add temporary
code
Attendance Setting Start add Done 7
code
Add