Onewireless - Wireless Device Manager User Guide
Onewireless - Wireless Device Manager User Guide
OWDOC-X254-en-220A
October 2013
Release 220
Document Release Issue Date
OWDOC-X254-en-220A 220 0 October 2013
Disclaimer
This document contains Honeywell proprietary information. Information contained herein is to be used solely
for the purpose submitted, and no part of this document or its contents shall be reproduced, published, or
disclosed to a third party without the express permission of Honeywell International Sàrl.
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a purpose and makes no express warranties except as may be stated
in its written agreement with and for its customer.
In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information
and specifications in this document are subject to change without notice.
Copyright 2013 - Honeywell International Sàrl
2 www.honeywell.com
Contents
3
CONTENTS
4 www.honeywell.com
CONTENTS
5
CONTENTS
6 www.honeywell.com
1 About this guide
This document describes the procedures to provision, configure, operate, and monitor an ISA100 Wireless
field device network using the Wireless Device Manager.
Intended audience
This guide is intended for people who are responsible for planning, configuring, administering, and operating
the OneWireless Network.
Prerequisite skills
It is assumed that you are familiar with the operation of OneWireless Network.
7
1 ABOUT THIS GUIDE
8 www.honeywell.com
2 Terms and definitions
Terms Definition
WDM Wireless Device Manager (WDM) is a device that manages the ISA100.11a wireless
field device network and all the ISA100.11a components connected to the OneWireless
network.
FDAP Field Device Access Point (FDAP) is a wireless infrastructure node that acts as an
ISA100.11a access point and a mesh node member. FDAP can only communicate
through ISA100.11a.
Field device A general term for process sensor (input) or process actuator (output) device.
Provisioning Device handheld Includes Personal Digital Assistant (PDA), mobile PCs and so on.
DD files Device Description files
DSSS Direct Sequence Spread Spectrum
FDN Field Device Network
PCN Process Control Network
HART Highway Addressable Remote Transducer
RSSI Receive Signal Strength Index
RSQI Receive Signal Quality Index
TxFailRatio Transmit Fail Ratio
GCI Gateway General Client Interface
9
2 TERMS AND DEFINITIONS
10 www.honeywell.com
3 Introduction
Related topics
“Overview of Wireless Device Manager” on page 12
“About OneWireless user interface” on page 16
“Overview of OneWireless Network setup” on page 17
11
3 INTRODUCTION
Functions of WDM
The WDM performs the following roles and functions within the ISA100 network.
Role Functions
Gateway • Acts as the communication interface for the ISA100 wireless field devices.
• Provides wireless field device data cache for the OneWireless user interface and the
external control systems.
• Allows communication between wired HART devices with OneWireless Adapter and the
asset management system.
System Manager • Manages the ISA100 wireless field device network and the devices.
• Establishes communication between the devices.
• Performs policy-based control of the network runtime configuration.
• Monitors and reports the communication configuration, performance, and operational
status.
Security Manager • It provides security keys to the Provisioning Device handhelds that are used for issuing
security keys to the field devices.
• Authenticates the provisioning data with which a field device tries to join the network.
• Initiates key rotation for the field devices.
• Maintains session key for each device in the network.
12 www.honeywell.com
3 INTRODUCTION
13
3 INTRODUCTION
Attention
The FDN port is also known as the “FIN – Field Instrument Network” port in
some WDMs.
Process Control Network (PCN) Used for connecting the monitoring clients and external controllers.
port
Attention
The WDM contains an embedded firewall that restricts the data routing between the two network ports.
COM ports Used for connecting to devices such as modems, terminals and various peripherals.
• WDMS — Has three serial ports, two of which can be used as standard RS232
ports and the third port can be used as an RS485 port
• WDMX — Has two serial ports, one of which can be used as standard RS232 port
and the other can be used as an RS485 port.
USB ports Used for connecting USB flash drives. In addition, USB ports are used for connecting
the PDA or provisioning device.
• WDMS — Has three USB ports
• WDMX — Has four USB ports
14 www.honeywell.com
3 INTRODUCTION
For more information about the technical specifications of the WDM models, refer to the specifications
document available at Honeywell Process Solutions website.
15
3 INTRODUCTION
16 www.honeywell.com
3 INTRODUCTION
17
3 INTRODUCTION
18 www.honeywell.com
4 Getting started with WDM
Related topics
“Mounting a WDM” on page 20
“Connecting the WDM and the other OneWireless components” on page 23
“Establishing communication between OneWireless Network and Experion system” on page 24
“Configuring network properties on the computer” on page 25
“Logging on to OneWireless user interface” on page 26
“Configuring WDM using the First Time Configuration Wizard” on page 27
“Understanding the OneWireless user interface” on page 33
“About map view” on page 47
19
4 GETTING STARTED WITH WDM
2 Hang the WDM onto the DIN-Rail with an angle of inclination about 30 degrees.
3 Lower the WDM straight down to slide over the Rail smoothly.
Attention
To remove the WDM from the Rail, push down on the top of the WDM, and then pull the bottom of the WDM
away from the Rail to disengage smoothly.
20 www.honeywell.com
4 GETTING STARTED WITH WDM
2 Mount the WDM on the wall using the 2 pairs of mounting holes.
21
4 GETTING STARTED WITH WDM
22 www.honeywell.com
4 GETTING STARTED WITH WDM
Prerequisites
• Ensure that you provide the maximum power requirement of 48 W (10 ~ 36 VDC).
• Ensure that you have an FDN Ethernet switch when connecting multiple FDAPs/Access Points to the WDM.
• Ensure that you have Ethernet cables required for connecting the devices.
• Ensure that you have redundancy Ethernet cable for connecting the devices.
• Identify the location for mounting the devices.
Establish physical connection between WDM and Cisco 1552S Access Point
1 Connect the Ethernet cable from the Ethernet port on the Cisco 1552S Access Point (AP) to the non-trunk
port on the Cisco switch.
2 Connect the Ethernet cable from the FDN port on the WDM to the non-trunk port on the Cisco Switch.
For more information about installing a Cisco 1552S AP, refer to the respective Cisco user documentation.
Attention
The WDM has the capability to act as the DHCP Server for the Field Device Network. However, if you are
configuring an external DHCP Server for the network, ensure you connect the DHCP Server to the switch during
this stage.
Attention
When powering up the WDM, if a duplicate IP address is configured on either the PCN port or the FDN port, the
WDM startup operation ends and no IP address is assigned. To recover, you must resolve the duplicate IP address
from the network .
23
4 GETTING STARTED WITH WDM
Attention
Ensure that the Experion Level–2 switch port where the WDM is connected, is set to auto speed, auto duplex.
Ensure that the Experion Level–2 switch port where the WDM is connected, has spanning-tree portfast enabled.
24 www.honeywell.com
4 GETTING STARTED WITH WDM
Prerequisites
• A desktop or a laptop computer for accessing the OneWireless user interface.
Attention
The steps in the following procedure are specific to Microsoft Windows XP operating system.
Attention
Note down the current settings in Internet Protocol (TCP/IP) Properties so that, if necessary, you can return to
their original values.
4 Configure the IP address and the Subnet Mask as 192.168.0.x and 255.255.255.0 respectively.
Attention
Do not configure the computer with the default IP address of the WDM, 192.168.0.1.
CAUTION
You must turn on a single WDM at a time, at the default address because the second WDM removes itself
from the network if its duplicate address is detected. The removed WDM does not recover unless power-
cycled.
25
4 GETTING STARTED WITH WDM
Prerequisites
• One of the following recommended Web browsers must be installed on the computer.
– Microsoft Internet Explorer 7.0 or higher
– Firefox 3.6 or higher
– Google Chrome 12.0 or higher
• Honeywell recommends a browser resolution of 1280 X 1024. Any resolution is supported but it may be
necessary to navigate scrollbars or adjust zoom levels to view the entire interface.
• Microsoft Silverlight 5 plug-in is required on the computer used for accessing the user interface. If the
computer has a prior version or it is not installed, then you are prompted to install or update the software
when you attempt to connect to the WDM. Honeywell is an authorized distributor of the Silverlight software
and a copy is maintained on the WDM for installs and upgrades; no internet or external connection is
required.
Attention
Silverlight is backwards compatible. You can still run prior applications based on earlier versions of Silverlight. To
save some initialization time during the first use on a new computer and if the computer has internet access, you
can pre-install the Silverlight 5 runtime environment at any time using the following link: http://
www.microsoft.com/getsilverlight/Get-Started/Install/Default.aspx.
Attention
The default User ID and Password configured for the WDM are as follows:
User ID: administrator
Password: password
Note that the Password is case-sensitive.
26 www.honeywell.com
4 GETTING STARTED WITH WDM
Attention
If you are performing a migration, skip this section and proceed with the tasks available in the OneWireless Migration
User’s Guide.
3 On the Wireless Device Manager Configuration page, click Configure New Wireless Device Manager
and click Next.
27
4 GETTING STARTED WITH WDM
4 On the Wireless Device Manager Settings page, type the WDM Tag Name and the Description.
The Tag Name is the unique name that is used to identify the WDM. It can be up to 16 characters long and
must begin with an alphabetic character. Do not use special characters in the Tag Name; underscore is the
only acceptable character. After completing the initial configuration, you cannot change the WDM name.
The Description can be up to 255 characters long.
5 If you need to configure redundant WDM, then under Redundancy Configuration, configure the
following:
a Select Enable redundancy for this Wireless Device Manager check box.
b Click the Redundancy Role, as required. You can select either Primary or Secondary option depending
on the redundancy role.
c In the Partner PCN IP Address box, type the PCN IP address of the partner WDM.
Attention
If an incorrect partner PCN IP address is configured, WDM does not synchronize. The incorrect PCN IP
address can be reconfigured on WDM Property Panel.
28 www.honeywell.com
4 GETTING STARTED WITH WDM
Tip
When redundancy is enabled, the primary WDM is assigned physical ID A and the secondary WDM is
assigned physical ID B. The physical IDs are displayed in the UI during normal operation. Tagging the
physical hardware with matching labels makes it easy to distinguish the WDMs later.
6 Click Next.
The Location Settings page appears.
Attention
If you have selected the Redundancy Role as Secondary in the Wireless Device Manager Settings page, then
the Location Settings page options are disabled.
9 Click Next.
The Network Settings page appears.
10 Under Field Device Network (FDN), configure the network settings for the wireless field device network as
follows.
• Field Device Network IP Address: These settings are used to configure the wireless field device
network Ethernet connection for the WDM. This is used for communication with FDAP.
Attention
– The IP address must be unique on the network, even if a redundant WDM pair is being configured.
– After completing the initial configuration, you cannot change the Field Device Network IP Address
specified in the First Time Configuration Wizard.
• Subnet Mask: A subnet mask identifies the bits of an IP address that are reserved for the network
address. For example, if the IP address of a particular node is 192.168.2.3 with a subnet mask of
255.255.255.0, the subnet mask indicates that the first 24 bits of the address represent the network
address. The last 8 bits can be used for individual node addresses on that network.
29
4 GETTING STARTED WITH WDM
• Assign Addresses to Field Device Access Points (Enable DHCP Server): Select this check box to
enable the WDM to act as the DHCP Server. Ensure you do not select the check box if the network has
another DHCP Server. It is recommended to enable the WDM to act as the DHCP Server.
• Field Device Access Point IP Address: This option is enabled only if you have selected the Enable
DHCP Server check box. Accept the default range or configure the IP address range according to the
network settings in the plant network. The WDM that acts as the DHCP Server assigns IP addresses
based on the range specified. Ensure that the IP addresses of the Access Points are not within the DHCP
address range.
If you do not enable DHCP Server during the first time configuration, it is possible to enable this at a
later stage using the Property Panel.
Attention
DHCP server configuration option is disabled on a secondary WDM.
11 Under Process Control Network (PCN), configure the process control network settings as follows.
• Process Control Network IP Address: The process control network settings are used to configure the
process control network Ethernet connections for the WDM. This is used for communication with
monitoring applications and external controllers.
Attention
The IP address must be unique on the network, even if redundant WDM pair is being configured.
• Subnet Mask
• Default gateway: Used to access the subnets outside the PCN subnet. This is an optional configuration
option.
12 Click Next.
The Network Time page appears.
Attention
The network time settings configuration is disabled on the secondary WDM. Upon synchronization, the secondary
WDM syncs time from primary over the FDN interface.
30 www.honeywell.com
4 GETTING STARTED WITH WDM
Attention
Network time settings configuration is disabled on the secondary WDM. Upon synchronization, the secondary
WDM syncs time from primary over the FDN interface.
Attention
• By default, the network time is configured as the system time.
• Consider the following while configuring an external NTP server.
– NTP server should be on the PCN or FDN.
– NTP server IP address must be within FDN or PCN subnet unless a default gateway has been configured
on the PCN subnet and the NTP server is accessible through the default gateway.
– NTP server IP address should not overlap with the FDN and PCN IP addresses.
– NTP server IP address should not overlap with FDAP IP address range, if DHCP Server is enabled.
14 If you are selecting NTP server, enter the NTP Server IP Address and click Next.
The Administrator Information page appears.
15 Type the user name and password in the Administrator Name, New Password, and Confirm Password
fields.
• The default user name configured for the WDM is administrator. You can change the default user name
in the First Time Configuration Wizard, if required. However, you cannot change the user name after
completing the initial configuration.
• The password must contain at least one character and can contain up to 32 characters. It should not start
or end with a space and must not contain single quote (‘).
Attention
When setting up a redundant WDM pair, it is recommended that the same default user name and password are
configured on primary and secondary WDM. This is because when the primary and secondary WDMs
synchronize, the secondary WDM's user account information is overwritten by the user accounts configured in the
primary. Providing identical configuration on both WDMs, avoids confusion related to login credentials when the
WDMs synchronize.
31
4 GETTING STARTED WITH WDM
16 Click Next.
The Configuration Summary page appears which displays the summary of all the configuration
information specified in the First Time Configuration Wizard. An incorrect entry is indicated by a
warning icon. Hovering the mouse over the icon displays a tooltip with the information about the incorrect
entry.
17 Verify the WDM settings, correct errors if any, and then click Finish.
If there are any errors in the configuration information that you have provided, then the system does not
allow you to click Finish.
18 On the Browser Redirect dialog box, click OK.
The wizard redirects the Web browser to the revised process control network IP address.
Attention
• If you are configuring the WDM to use the same process control network IP address, then the wizard redirects
the Web browser.
• If you have configured the WDM using a different PCN IP subnet than the computer, then you need to
reconfigure the network settings of the computer to access the user interface using the IP address on the new
subnet.
32 www.honeywell.com
4 GETTING STARTED WITH WDM
The ribbon bar in the user interface contains the following tabs and icons.
33
4 GETTING STARTED WITH WDM
Tab/icon Description
Display group
Monitoring tab displays the topological view of the OneWireless Network.
Use the Monitoring tab to add, configure, and commission wireless field devices
and monitor the devices in a topological view. The topological view of the network
is known as the map view. For more information about the map view, refer to the
section, “About map view” on page 47.
Attention
The Monitoring tab is disabled on the secondary WDM.
The Alarms & Events tab displays the alarms and system events generated by the
wireless field devices in a tabular format. An alarm is generated whenever an
abnormal condition occurs. An event is any significant change in the system, and
includes alarms and operator actions. The Alarms & Events tab contains the
following sub elements.
• The Active Alarms tab: Lists the devices, device diagnostic alarms and their
respective location, source, start time, priority, and description.
• The Alarms/Events History tab: Provides a tabular view of the events. It is
possible to export the alarm log and the event log for a particular period.
Reports tab displays device performance and connectivity reports.
Use the Reports tab to generate and view predefined reports that are used to
maintain and optimize the network and the field devices.
The following are the reports that can be generated:
• Battery Life
• Device Health Overview
• Device Summary
• Device History
• Connection Summary
• Connection History
Filtering group
The Filter option in the ribbon bar allows you to customize the device list by
filtering the devices. By default, all the devices appear in the device list. You can
filter by Device Type, Device Status, Vendor, Model, Power Source, Alarm Priority,
Hop Level, and Maps.
Attention
When you set a filter, various system views are altered. For example, the map
highlights only the devices for which the filter option is applied. All the
filtered out devices appear as blurred in the map.
Filter includes an option to filter by Map. This includes the Unplaced map so
any device that has not been placed on a map can easily be detected. Note that
since a device can be placed on more than one map, it can appear in the set of
filtered devices for different maps.
Provisioning group
34 www.honeywell.com
4 GETTING STARTED WITH WDM
Tab/icon Description
• Accept: Accepts devices that can be provisioned using over-the-air provisioning
method.
• Reject: Rejects devices that are attempting to join the network using over-the-air
provisioning method.
• Delete: Removes a provisioned device from the network. Removing a device
from the network clears the provisioning data and restores the device to factory
default state. It can also be used to remove a rejected unprovisioned device from
the user interface in case you have mistakenly rejected a device earlier.
Removing a rejected device enables the device to rejoin as an unprovisioned
device. You can then accept the unprovisioned device to join the network.
Note the following points while deleting a device from the network.
– Deleting a joined device removes the provisioning data and the configuration
data from the device and the WDM. Also, the device restores to factory
default state.
– Deleting an offline device removes the provisioning data and the
configuration data of the device only from the WDM. The provisioning data
and the configuration data needs to be manually cleared from the device
using the PDA.
Only the Delete option is available on the secondary WDM.
Channel group
• Activate: Activates all the channels of the selected field device. Clicking the
Activate transitions the field device channel state from OOS to the currently
configured Normal mode.
• Inactivate: Inactivates all the channels of the selected field device. Clicking the
Inactivate button transitions the field device channel state from AUTO to OOS.
Attention
This group is disabled on the secondary WDM.
Maintenance group
• Templates: Uploads the vendor supplied DD file to the WDM.
• Replace: Displays the help information for performing the replace operation.
• Point Picker: Enables you to browse parameters on all devices and then drag
and drop parameter into MODBUS coil or register configuration.
Attention
This group is disabled on the secondary WDM.
Upgrade group
• Application: Initiates firmware upgrade operation for the WDM and the
application firmware of the field devices.
• Radio: Initiates firmware upgrade operation for the access points and the radio
firmware of the field devices.
System group
35
4 GETTING STARTED WITH WDM
Tab/icon Description
• Manage Users: Opens the Manage Users dialog box that contains the options to
add, delete, or edit new user accounts.
• Change Password: Enables you to change the current user’s password.
• Export System Log: Exports and saves the system logs that record information
about events in the application instances.
• Manage Roles: Opens the Manage Roles dialog box that enables you to modify
the configured user-permitted operations.
• Software: Enables you to download software provided on WDM.
Attention
Only the Export System Log option is available on the secondary WDM.
Displays the user who has currently logged on to the OneWireless user interface.
Invoke the context-sensitive help. Note that this functionality is currently not
supported.
36 www.honeywell.com
4 GETTING STARTED WITH WDM
The following table describes the different elements/icons available in the Selection Panel.
Element Function
Click to expand the Selection Panel.
Click to view the extended Selection Panel. It provides information about the
properties of the devices such as device type, status, vendor, model, serial number,
and so on.
37
4 GETTING STARTED WITH WDM
Element Function
Click to collapse the devices in the Selection Panel.
The Show Radio Identification check box allows you to view the radio related details about the field devices.
The following illustration depicts the extended Selection Panel with Show Radio Identification check box
selected.
38 www.honeywell.com
4 GETTING STARTED WITH WDM
Figure 10: Extended Selection Panel with radio details of the devices
Redundant WDM
External interfaces
By default, the external interfaces appear within the WDM icon.
39
4 GETTING STARTED WITH WDM
40 www.honeywell.com
4 GETTING STARTED WITH WDM
Channel icons
41
4 GETTING STARTED WITH WDM
Channel becomes grey when the data is being fetched from the device. For a
digital output channel, grey indicates the MAN mode, where you can
manually set the output value.
Offline channel
Primary is Joined, Partner is visible over private path but not syncd. Partner
may be incompatible.
42 www.honeywell.com
4 GETTING STARTED WITH WDM
Secondary view
Secondary is Unknown (default Primary).
Secondary is Joined, Partner is visible over private path but not syncd. Partner
may be incompatible.
43
4 GETTING STARTED WITH WDM
44 www.honeywell.com
4 GETTING STARTED WITH WDM
Attention
On the secondary WDM UI, some accordion panels like System Manager, Configuration, Date and Time,
Provisioning, Provisioning Devices, and Notes are not displayed. For example, refer to the following figure.
The following table describes the different elements/icons available in the Property Panel.
Element Function
Click to expand the Property Panel.
Apply icon. Click to save any configuration changes applied. This icon is enabled only
if you have made any changes in the user interface.
Reset icon. Click to reset any unsaved changes made to the devices through the
Property Panel. This icon is enabled only if you have made any changes in the user
interface.
45
4 GETTING STARTED WITH WDM
Element Function
Alarms panel allows to view the alarm details (Priority, Start Time, and Description)
for any device selected in the Selection Panel.
Pane Description
Number of online devices.
Displays all the active alarms. Click the Alarms box to open the
Active Alarms table in the Alarm/Events tab.
46 www.honeywell.com
4 GETTING STARTED WITH WDM
The following are the map navigation controls that are available in the map view.
47
4 GETTING STARTED WITH WDM
48 www.honeywell.com
4 GETTING STARTED WITH WDM
Attention
Depending on the Overlay option selected,
the other options available are displayed.
49
4 GETTING STARTED WITH WDM
50 www.honeywell.com
4 GETTING STARTED WITH WDM
The device icons in the map view contain the following indicators using which you can analyze the battery
level, the publishing rate, and the bandwidth usage of devices.
51
4 GETTING STARTED WITH WDM
52 www.honeywell.com
5 Configuration
Related topics
“Configuring a Provisioning Device handheld” on page 54
“Loading the Device Description file” on page 59
“Provisioning the OneWireless Network components” on page 60
“Configuring the WDM” on page 65
“Configuring the WDM redundancy” on page 68
“Monitoring the WDM redundancy status” on page 73
“Configuring device communication redundancy” on page 78
“Configuring field devices” on page 80
“Configuring field device channels” on page 85
“Adding notes for devices” on page 91
53
5 CONFIGURATION
Related topics
“Install synchronization software on the computer” on page 54
“Install Microsoft .NET Compact Framework 3.5 on the Provisioning Device handheld” on page 54
“Install Provisioning Device Application on the Provisioning Device handheld” on page 56
“Generate and transfer the provisioning keys to the Provisioning Device handheld” on page 57
“Remove Provisioning Device handheld” on page 58
5.1.2 Install Microsoft .NET Compact Framework 3.5 on the Provisioning Device handheld
To install Microsoft .NET Compact Framework 3.5 on the Provisioning Device handheld
1 On the ribbon bar, in the System group, click Software.
The Support Software dialog box appears.
54 www.honeywell.com
5 CONFIGURATION
2 From the Select Software list, select the MS .NET Compact Framework v3.5 software.
3 Click Save To to save the software to the computer.
A confirmation message Do you want to save the NETCFSetupv35? appears.
4 Click OK.
The Save As dialog box appears.
5 Browse to a location on the hard drive to save the MS .NET Compact Framework v3.5 software.
• By default, the file name appears as NETCFSetupv35, if you want to change the file name, then type the
File name.
6 Click Save.
7 Connect the Provisioning Device handheld’s docking station to a USB port on the computer.
8 Place the Provisioning Device handheld on the docking station.
9 Switch on the Provisioning Device handheld.
10 The computer detects the Provisioning Device handheld and the Synchronization Setup Wizard dialog box
appears.
11 Click Cancel to continue.
It is not necessary to complete the synchronization setup before installing the Provisioning Device
Application.
The Microsoft ActiveSync dialog box appears with the status as connected.
12 On the computer, browse to the location where Microsoft .NET Compact Framework 3.5 setup file is saved.
13 Run the setup file on the computer and follow the on-screen instructions to complete the installation.
The Provisioning Device handheld displays the progress of the installation.
55
5 CONFIGURATION
Attention
If Microsoft .NET Compact Framework 3.5 is already installed on the computer, in order to reinstall, you must
remove it using Add/Remove Programs.
Prerequisites
• Ensure that you have logged on to the OneWireless user interface.
• Ensure that the Provisioning Device handheld is connected to the computer and the connection status
appears as green in ActiveSync on the computer.
56 www.honeywell.com
5 CONFIGURATION
5.1.4 Generate and transfer the provisioning keys to the Provisioning Device handheld
Prerequisites
• Ensure that the Provisioning Device Application is installed on the Provisioning Device handheld.
• Ensure that the Provisioning Device Application is running on the Provisioning Device handheld.
To generate and transfer the provisioning keys to the Provisioning Device handheld
1 Connect the Provisioning Device handheld’s docking station to the USB port on the WDM.
2 In the OneWireless user interface, select the WDM on the Selection Panel.
3 On the Property Panel, expand Provisioning.
4 Click Transfer to PDA and type the following information under Settings.
• Name: Unique name used to identify the Provisioning Device handheld.
• Number of Keys: The number of provisioning keys to be transferred to the Provisioning Device
handheld. These keys are deployed to FDAPs, Access Points, and field devices through the IR port.
Maximum number of keys that can be transferred at a time is 100.
• Expiration (days): The expiration period for the provisioning keys in the Provisioning Device handheld.
The maximum expiration period is 31 days. To calculate the expiration period correctly, ensure that the
PDA time is manually synchronized with the system time.
Attention
If the Provisioning Device handheld is already configured with the provisioning keys from another OneWireless
Network or from the same network, the provisioning data from the earlier configuration is displayed on the
Provisioning panel. To transfer the new keys, rewrite the values in the fields with the new values.
57
5 CONFIGURATION
6 On the Provisioning Device handheld, tap Start > Programs > Provisioning Device.
The Provisioning Device screen appears.
7 Verify Network ID, No. of keys, and Expiry that appears on the Provisioning Device handheld.
58 www.honeywell.com
5 CONFIGURATION
Attention
• DD files loaded prior to migrating the WDM to R220 are discarded to resolve the R2xx to R220 migration
anomaly. Note that this is a one time behavior that is not repeated after migration to future releases.
• To ensure consistency in the channel names, load the DD files before the device joins the network.
59
5 CONFIGURATION
Related topics
“Provision the devices using Provisioning Device handheld” on page 60
“Provision the devices using over-the-air provisioning method” on page 60
Prerequisites
• Ensure that the FDAP/Access Point/field device is powered on.
• Provisioning Device Application must be installed on the Provisioning Device handheld.
• Provisioning Device handheld must be configured with valid keys from the WDM.
Attention
If the FDAP/Access Point/field device is already provisioned, a message displays on the Provisioning Device
handheld screen, prompting to reset the device to default and try again. To restore the device settings:
1. Hold the Provisioning Device handheld in line with the IR port of the device to be provisioned.
2. Tap Reset to defaults on the Provisioning Device handheld.
5 Repeat the procedure to add the other FDAPs/Access Point/field devices to the network.
60 www.honeywell.com
5 CONFIGURATION
WDM and the device in the unprovisioned state. You can accept or reject an unprovisioned device using the
user interface. If accepted, the WDM sends the provisioning data to the device and the device transitions to
provisioning state. A device with the new security data sends join request to the WDM. This is similar to the
join request received by the WDM when a device is provisioned using a Provisioning Device handheld.
4 Click Apply.
The unprovisioned access points start appearing in the Selection Panel. You can filter the device list to view
only the unprovisioned access points in the network.
61
5 CONFIGURATION
5 On the ribbon bar, in the Filter group, click Device Status > Un-Provisioned.
6 Expand the extended Selection Panel to view the available device parameters.
7 Select the required access point in the Selection Panel or the map view and then click Accept on the ribbon
bar.
Attention
• You can select multiple access points using the Selection Panel or the map view. Use SHIFT+click to select
multiple items in a successive list. Use CTRL+click to select multiple items not in succession.
• It is recommended that you select and accept only 10 devices at a time.
The Accept Over the Air Devices dialog box appears. The dialog box displays all the unprovisioned access
points that you have selected for enabling over-the-air provisioning.
8 Click Accept.
The Progress column displays the status as In Progress, Provisioning, and then Completed when
complete. Do not close the dialog box when over-the-air provisioning is initiated for devices.
9 Click Close.
The Accept Over the Air Devices dialog box closes.
To provision line-powered FDAP routers/ field devices using over-the-air provisioning method
1 On the Selection Panel, select the access point.
2 On the Property Panel, expand Device Management.
3 Under Over The Air Provisioning, click Enable for 60 Minutes.
62 www.honeywell.com
5 CONFIGURATION
The access point functions as a provisioning device for 60 minutes. The unprovisioned field devices and the
line-powered FDAP routers that are in the factory default state start appearing in the Selection Panel. Note
that if you do not accept or reject the devices within 60 minutes, the devices automatically disappear from
the user interface.
4 To filter the device list:
On the ribbon bar, in the Filter group, click Device Status > Un-Provisioned.
The unprovisioned devices appear in the Selection Panel. The extended Selection Panel enables you to view
the available device parameters.
The device establishes a communication link with the access point after it attains the unprovisioned state.
This link persists even if the device is not provisioned using the connected access point. If the device needs
to be provisioned using a different access point, reject the device and then delete it from the user interface,
so that the device can rejoin through a different access point for provisioning.
5 Select the required line-powered FDAP router/ field device in the Selection Panel or the map view and then
click Accept on the ribbon bar.
Attention
• You can select multiple access points using the Selection Panel or the map view. Use SHIFT+click to select
multiple items in a successive list. Use CTRL+click to select multiple items not in succession.
• It is recommended that you select and accept only 10 devices at a time.
The Accept Over the Air Devices dialog box appears. The dialog box displays all the unprovisioned
devices that you have selected for enabling over-the-air provisioning.
63
5 CONFIGURATION
Attention
To reject a device from joining the network using over-the-air provisioning method.
1. Select the required device and click Reject in the ribbon bar.
The Reject Over the Air Devices dialog box displays.
2. Click Reject.
The Progress column displays the status as In Progress, and then Completed, when complete.
3. Click Close.
The Reject Over the Air Devices dialog box closes.
6 Click Accept.
The Progress column displays the status as In Progress, Provisioning, and then Completed, when
complete. Do not close the dialog box when over-the-air provisioning is initiated for devices.
7 Click Close.
The Accept Over the Air Devices dialog box closes.
All the line-powered FDAP routers and the field devices that you have selected for over-the-air provisioning
are provisioned.
Attention
Repeat the procedure to enable over-the-air provisioning capability in line-powered FDAP routers. This enables
the line-powered FDAP routers to provision distant nodes in the network.
64 www.honeywell.com
5 CONFIGURATION
Related topics
“Configure default routing policy” on page 65
“Configure key rotation period” on page 66
“Configure channel blacklisting” on page 66
65
5 CONFIGURATION
This corresponds to the RSQI value between the devices. The link between the devices is established only if
RSQI is equal to or greater than the Link Quality Threshold limit. By default, Link Quality Threshold is
set to 127.
CAUTION
Honeywell recommends that you set the Link Quality Threshold as 127. To set the Link Quality Threshold
to any other value other than 127, you must contact a Honeywell technical support representative for
assistance.
The Link Quality Threshold does not apply if the device has only one primary link.
6 Select one of the following Default Join Policy options, as required.
The Default Join Policy specifies the system-wide join policy for the routing devices (FDAP routers and
routing field devices). The system – wide join policy can be overridden by the join policy of the device.
By default, the join policy for the devices is configured as Join Enabled.
• Join Enabled — Enables the devices to join the network through FDAP routers and routing field
devices.
• Join Enabled, Line Powered Only — Enables the devices to join the network only through FDAP
routers.
7 Click Apply.
The configured routing policy is applicable only for devices that are joining the network for the first time.
66 www.honeywell.com
5 CONFIGURATION
The fixed channels appear under ISA100 Fixed Channels and the user configurable channels appear under
ISA100 Configurable Channels.
3 Select the check boxes for the channels, as required.
4 Click Apply.
It takes approximately 90 seconds for the changes to reflect.
67
5 CONFIGURATION
Attention
Redundancy is supported only on the WDMX hardware (with three Ethernet ports).
68 www.honeywell.com
5 CONFIGURATION
Attention
– Cisco Catalyst 2960 Series 8 port switches and Cisco Catalyst 2960G Series 24 port switches are the supported
FDN switches. For more information, refer to the Cisco Catalyst 2960 Series documents.
– For information about the Cisco Access Point configuration, refer to the OneWireless Wireless LAN
Controller Configuration Guide.
– You can use a single PCN/single FDN switch or a dual PCN/dual FDN switches. Single switches are used for
simple networks, less expensive, possible single point of failure. Dual switches are used for more robust
networks, which are more expensive, but do not contain single point of failure.
In case you plan to set up a redundant WDM, ensure the following:
1. CISCO switch port, where the WDM is connected, is configured to operate in access mode.
2. Spanning-tree portfast feature is enabled.
3. Speed is set to auto.
4. Port is in full duplex mode.
For an example of the CISCO switch configuration for WDM port, refer to the OneWireless Migration User's
Guide.
5.5.1 Configure the WDM redundancy from the First Time Configuration Wizard
You can configure the WDM redundancy from the First Time Configuration Wizard (FTCW). For more
information, refer to the section “Configuring WDM using the First Time Configuration Wizard” on page 27.
69
5 CONFIGURATION
5.5.2 Configure the WDM redundancy from the WDM Properties Panel
Redundancy configuration may be enabled, disabled, or modified on-process from the WDM Properties Panel.
Changes performed to redundancy configuration from the WDM Properties Panel only apply to that WDM, and
are not automatically cascaded to the redundant partner. For example, if redundancy is disabled on a primary
WDM, the redundant partner remains in secondary role.
70 www.honeywell.com
5 CONFIGURATION
Attention
To disable redundancy on a secondary WDM, reset it to defaults and then configure as non-redundant from FTCW.
Redundancy commands
Refer to the section “Perform redundancy-specific operations” on page 75.
Primary view
The Primary WDM is used for monitoring the ISA100 Wireless field device network and the devices, initiating
all the commands, and viewing alarms and events. Primary WDM monitors and reports the communication
configuration, performance, and operational status. The external interfaces such as MODBUS, HART, OPC,
GCI, and ENRAF are only available on the primary WDM. CDA interface is available on both the primary and
secondary WDMs.
Secondary view
The secondary WDM has limited functionality and is used for monitoring redundancy parameters, initiating
redundancy commands, and viewing the secondary WDM alarms and events. The access points, field devices,
or external interfaces are not displayed on the secondary WDM. CDA external interface is not displayed on the
secondary WDM. However, secondary WDM can be accessed from Experion through CDA interface.
The following are not available in the Properties Panel of the secondary WDM.
• System Manager
• Configuration
• Date and Time
71
5 CONFIGURATION
• Provisioning
• Provisioning Devices
• Notes
The external interfaces are only available on the primary WDM (except CDA). External clients cannot connect
to the secondary WDM using Modbus, HART, OPC, GCI, and ENRAF. The CDA interface is available on both
the primary and the secondary WDMs. The external clients are reconnected to the old secondary/new primary
immediately after switchover, using the primary WDM configuration. Redundancy status parameters and
commands are available when integrated with Experion R410 and later.
72 www.honeywell.com
5 CONFIGURATION
Status Bar
The Status Bar contains the overall redundancy status as text.
Selection Panel
The WDM icon on the Selection Panel changes depending on the redundancy role. For information regarding
the different WDM icons, refer to “Understand the device icons” on page 39.
5.6.1 Monitor the redundancy status from the WDM Property Panel
3 Under Summary, verify the Redundancy Role, Synchronization State, Initial Sync Progress, Inhibit
Sync Reason, and Redundancy Physical ID.
4 Under Status, verify Hardware Supported, Partner Creds Syncd, Redun Controllability, Redun
Compatibility, and Auto Sync State, Pending Critical Data, and Pending Non-Critical Data.
73
5 CONFIGURATION
The following table describes the attributes displayed in the Redundancy tab of the WDM Property Panel.
Attributes Description
Summary
Redundancy Role Indicates the current redundancy role - primary, secondary, or non-redundant.
Synchronization State Indicates level of module synchronization with redundancy partner as follows: -
Partner Visible, Initial Sync Progress, Synchronized, No Partner, Incompatible.
• Partner Visible: Communication is established over the RDN private path, but the
WDMs are not yet synchronized.
• Initial Sync Progress: Initial sync is in progress.
• Initial sync is complete and WDMs are in sync maintenance state.
• No communication over RDN private path.
• Redundant partner is not compatible for synchronization.
Initial Sync Progress (%) Indicates the percentage of initial-sync completion. This is set to zero when initial
sync is not in progress and it is set to 100 when initial sync is complete.
Inhibit Sync Reason Indicates the current reason why initial sync is inhibited.
Redundancy Physical ID Used to identify the physical hardware module.
The Redundancy Physical ID attribute is used for identifying the physical hardware
module. By default, when a WDM is configured in a primary role, the value of its
attribute is set to A. When a WDM configured in a secondary role the value of its
attribute is set to B. These values are attached to the physical hardware and not the
redundancy role. In other words, starting from a redundant synchronized WDM pair,
where the WDM with a physical ID A is primary and the WDM with a physical ID B
is secondary, if a switchover occurs, the WDM physical ID B will be in primary role
and the WDM with physical ID A will reboot into secondary role. If the phsyical
hardware is so labeled, it is possible to identify the WDM currently in Primary role.
Status group
Hardware Supported Indicates whether redundancy is supported on current hardware. WDM redundancy is
not supported on WDMS hardware.
Partner Creds Syncd Indicates whether WDMs have synchronized at least once. On a lonely secondary, the
become primary command is disabled if this check box is not selected.
Redun Controllability Describes the module’s ability to control relative to its redundant partner. For
example, on an unsynchronized redundant WDM pair, if the primary's FDN or PCN
cable is disconnected, but the secondary's FDN and PCN cables are connected, then
the secondary has better control ability than the primary. And the primary WDM's
control ability is worse than the secondary. Note that on such a redundant WDM pair,
if synchronization is enabled, then the WDMs synchronize and immediately
switchover since the secondary's control ability is better than that of the primary.
Switchover can be initiated from primary or secondary WDM. The following
conditions result in switchover:
• FDN or PCN Ethernet cable is disconnect on the primary WDM.
• Loss of power on the primary WDM.
• Software failure on the primary WDM.
• Hardware failure on the primary WDM.
Redun Compatibility Indicates whether redundant partner modules are compatible and if not compatible,
provides a reason. Initial synchronization is disabled on an incompatible WDM pair.
Auto Sync State Indicates whether auto synchronization is enabled or disabled. When disabled, you
must explicitly issue the Enable Synchronization command to reset any persistent
fault condition and (re)attempt initial synchronization.
74 www.honeywell.com
5 CONFIGURATION
Attributes Description
Pending Critical Data Number of critical sync data bytes yet to be sent to partner. This value is usually 0.
An increase may be observed during initial synchronization, which rapidly reduces to
0.
Pending Non-critical data Number of non-critical synchronization data bytes yet to be sent to the partner. This
value may increase to a large value during initial synchronization, and gradually
reduce to zero.
Last Sync Time Time when the WDM completed initial synchronization.
Last Loss of Sync Time Time when the WDM last lost synchronization.
Statistics The attributes in this group indicate whether redundant WDMs are communicating
over the RDN private path. A steadily increasing Tx count indicates that data is
successfully being transmitted to partner. A steadily increasing Rx count indicates
that data is successfully being received from the partner.
5 On the Property Panel, expand Redundancy History to view the history details. The Redundancy
History tab displays the 16 most recent redundancy events along with a reason why the event occurred. For
example, in the figure provided below, the role change state is reported with reason
InitiateSwitchoverCommand indicating that a role change occurred at 2 PM on 9/17/2013 due to user-
initiated switchover command.
Enable Synchronization
The Enable Synchronization option enables auto synchronization and is used for initial synchronization. The
maximum initial synchronization time is 180 seconds.
75
5 CONFIGURATION
Attention
Redundancy command buttons are disabled if they do not apply to the current redundancy state. For example, ‘Enable
Synchronization’ is disabled when synchronized.
To enable synchronization
• On the Property Panel, expand Redundancy, and then click Enable Synchronization.
Disable Synchronization
The Disable Synchronization option disables auto synchronization and used for drop synchronization.
To disable synchronization
• On the Property Panel, expand Redundancy, and then click Disable Synchronization.
Initiate Switchover
The Initiate Switchover option enables immediate switchover of synchronized WDM pair. The switchover
time is 15 seconds.
Switchover can be initiated from the primary or the secondary WDM. The following conditions result in
switchover:
• FDN or PCN Ethernet cable is disconnect on the primary WDM.
• Loss of power on the primary WDM.
• Software failure on the primary WDM.
• Hardware failure on the primary WDM.
To initiate switchover
• On the Property Panel, expand Redundancy, and then click Initiate Switchover.
76 www.honeywell.com
5 CONFIGURATION
Attention
Since the secondary is not synchronized with the primary when this command is executed, it may have stale
configuration data. You must manually check and re-configure devices and other settings as appropriate. The
following data is preserved in the secondary WDM since the last sync drop event:
• Primary WDM name.
• Primary WDM FDN IP address.
• Primary WDM PCN IP address.
• Primary WDM external NTP server configuration.
• Primary WDM DHCP server configuration.
• DHCP leases given out by primary WDM.
• Security keys already used by devices to join the network.
• Country code.
• Subnet ID.
• TAI offset.
• User accounts, their roles, and permissions.
Toggle Physical ID
The Toggle Physical ID option to toggle physical ID from B to A or A to B.
When the redundant WDMs are communicating over the private path, the physical IDs of both the WDMs is
toggled, regardless of whether the command was sent to the primary or the secondary WDM. If redundant
WDMs are not communicating over the private path, only the WDM to which the command was sent is
affected.
Tip
When redundancy is enabled, the primary WDM is assigned physical ID A and the secondary WDM is assigned
physical ID B. The physical IDs are displayed in the UI during normal operation. Tagging the physical hardware
with matching labels makes it easy to distinguish the WDMs later.
77
5 CONFIGURATION
5.7.2 Report
The report now displays the communication redundancy information. For example, Connection Summary
report.
78 www.honeywell.com
5 CONFIGURATION
79
5 CONFIGURATION
Related topics
“Configure field device properties” on page 80
“Configuring routing assignment” on page 80
“Configure publication rate” on page 81
“Calibrate field devices” on page 82
Attention
You can change the Tag Name by double-clicking the field device name in the Selection Panel.
80 www.honeywell.com
5 CONFIGURATION
The Join Assignment overrides the system manager join policy. This is applicable only for routing field
devices.
• Join Disabled — Disables device-join through this device.
• Join Enabled — Enables device-join through this device.
• Follow System Manager Policy — Enables the device to follow the system manager join policy.
Device-join through this device depends on the configured system manager join policy.
The Join Status is a read-only parameter that indicates the resultant join state for all the devices.
• Access Points, FDAP access points, and FDAP routers have the Join Assignment permanently set to
Join Enabled.
• Non-routing field devices have the Join Assignment permanently set to Join Disabled.
• Routing field devices have the default Join Assignment set to Follow System Manager Policy.
5 Click Apply.
Attention
When a device joins the network, the WDM automatically configures its publication period as 30 seconds.
81
5 CONFIGURATION
82 www.honeywell.com
5 CONFIGURATION
83
5 CONFIGURATION
84 www.honeywell.com
5 CONFIGURATION
Related topics
“Configure Mode and Scale” on page 85
“Add channels to publication groups” on page 85
“Configure channel instantiation” on page 86
“Remove channels from publication groups” on page 89
“Delete (uninstantiate) channels” on page 90
To configure Scale
1 On the Selection Panel, select the field device channel.
2 On the Property Panel, expand Process Variable to view the following read-only parameters in the
OneWireless user interface.
• EU at 100%: Specifies the high range PV value in Engineering Units.
• EU at 0%: Specifies the low range PV value in Engineering Units.
• Units Index: Specifies the unit of the measurement value. The value varies according to the sensor type
selected for a channel.For example, in a temperature device, when the sensor type changes to a
thermocouple (TC-J) or mV-50 range, the transducer block sets the Units Index to °C or mV.
3 Click Apply.
Attention
After applying the changes, the newly configured values appear under the Scale panel.
To configure Mode
1 On the Property Panel, expand Mode.
2 In the Target list, select the mode as required.
The mode types available are Normal, OOS, and Auto. If the device type is Digital Output (DO), an
additional mode Man is also available in the Target list.
3 Click Apply.
85
5 CONFIGURATION
Attention
To disable data publication, select None in the Channel list.
4 Click Apply.
86 www.honeywell.com
5 CONFIGURATION
4 Click Apply.
Wait for a few seconds to save the changes.
87
5 CONFIGURATION
2 Click Apply.
The channel disappears from the map view and the Selection Panel.
To instantiate channel
1 Expand Channel Configuration and click the respective instantiable object type for the channel to be
instantiated.
In the following example illustration, the temperature DI field device has three instantiable channels. Each
channel can be instantiated as an analog input channel or a binary input channel.
88 www.honeywell.com
5 CONFIGURATION
2 Click Apply.
89
5 CONFIGURATION
4 Click Apply.
Prerequisites
• Ensure that the channel is set to OOS mode.
• Ensure that the channel is not configured for publication in any of the Input/Output Publication groups. If
configured, remove the channel from the Publication group.
To delete channels
1 On the Selection Panel, select the field device channel.
2 On the Property Panel, expand Channel Configuration.
The Channel Configuration panel displays a list of instantiated channels.
3 Select the channel to delete and select Unassigned in the corresponding drop-down list.
4 Click Apply.
90 www.honeywell.com
5 CONFIGURATION
To add notes
1 On the Selection Panel, select the required device.
2 On the Property Panel, expand Notes.
3 Click the Add note icon.
A text box appears.
Attention
• All users can view all the notes added by other users.
• To delete any note added, click delete icon adjacent to the note.
– Users with User role can delete only notes added by them.
– Users with Administrator role can delete other user’s notes.
• Notes are not restored during a replace operation.
To edit a note already added, double-click on the note that you want to edit, make the necessary changes,
and then click Apply.
91
5 CONFIGURATION
92 www.honeywell.com
6 Operations
Related topics
“Setting up the monitoring area” on page 94
“Configuring Connection Quality Options” on page 98
“Verifying connectivity using maps” on page 99
“Configuring alerts for Honeywell field devices” on page 101
“Monitoring the network and the devices” on page 102
“Alarm and event management” on page 104
“Viewing time synchronization parameters” on page 118
“Viewing license agreement files” on page 119
93
6 OPERATIONS
94 www.honeywell.com
6 OPERATIONS
3 Click Add.
4 Under Map Configuration, in the Map Name box, type the name of the map.
5 In the Description box, type the description for the map.
6 Click Load Image.
The Open dialog box appears.
7 Browse to the location where the site map is saved, and then select the site map.
Attention
The site map must be a .jpg file of any size.
Attention
• By default, the map display is hidden. To display the map, on the top-right of the map view, click
Options>View > Show Map.
• To increase or decrease map visibility, click Options > View > Map Opacity > fade in /fade out.
For more information about map controls, refer to the section, “About map view” on page 47.
9 Click Save.
Attention
In the Manage Maps dialog box, click Delete to remove any previously loaded site map. In the Manage Maps
dialog box, click Edit to edit the site map details.
95
6 OPERATIONS
96 www.honeywell.com
6 OPERATIONS
Attention
The Default Map list displays all the maps on which the device is placed.
97
6 OPERATIONS
2 In the boxes near the separator bars, type the RSSI, RSQI, and TxFailRatio values or drag the separator bars
up and down.
3 Click Apply, and then click OK.
Attention
Click Restore Defaults to restore the Honeywell recommended default values.
98 www.honeywell.com
6 OPERATIONS
4 Verify device communication statistics information such as RSQI, RSSI, and TxFailRatio.
A green line between the devices in the map view indicates strong signal quality, whereas a red line indicates
weak signal quality. A solid line between the devices represents an active connection between the devices
and a dotted line represents an inactive connection.
The connection quality details are displayed as tool tip when you hover the mouse over the connection.
Option Description
RSQI range 235 to 255: Excellent
180 to 235: Good
150 to 180: Fair
0 to 150: Poor
RSSI range -75 to -25: Good
-85 to -75: Fair
-100 to -85: Poor
TxFailRatio 0 to 20: Good
20 to 50: Fair
50 to 100: Poor
99
6 OPERATIONS
Attention
While configuring the network, ensure that the lowest RSQI on each active link is greater than 180 and the lowest
RSSI on each active link is greater than -80 dbm. An active link with RSQI/RSSI values higher than the specified
values protects the signals when the signal strength/quality degrades due to transient environmental conditions.
100 www.honeywell.com
6 OPERATIONS
101
6 OPERATIONS
The following tables explain the device and the channel attributes that are available in the extended Selection
Panel.
102 www.honeywell.com
6 OPERATIONS
You can view the PV trend in the Values and Trends panel of the channel’s Property Panel.
103
6 OPERATIONS
Related topics
“Understand alarms and events” on page 104
“Monitor alarms and events” on page 116
104 www.honeywell.com
6 OPERATIONS
105
6 OPERATIONS
106 www.honeywell.com
6 OPERATIONS
107
6 OPERATIONS
108 www.honeywell.com
6 OPERATIONS
109
6 OPERATIONS
110 www.honeywell.com
6 OPERATIONS
111
6 OPERATIONS
112 www.honeywell.com
6 OPERATIONS
113
6 OPERATIONS
• For
externa
lly
powere
d
devices
,
immedi
ate
action
is
require
d.
Field device Out of Invalid or Channel may Perform user Immediate DIAG_ST 0
Specification unreadable report calibration. ATUS,
Alert calibration data. incorrect PV DIAG_ST
value. ATUS_D
ETAIL
Field device Failure Status • An • Loss of • Restart the Immediate DIAG_ST 0
Alert electronics communic field device ATUS,
failure, ation with radio and DIAG_ST
including the field sensor. If ATUS_D
NVM fault, device and condition ETAIL
RAM fault, the persists,
program associated replace the
memory channels. sensor
fault, or A/D • Channel module.
failure is reports • Check the
detected by incorrect connectors
the field PV value. on the
device terminal
sensor. board and
• Cold sensor
junction module.
failure. Replace the
terminal
board.
114 www.honeywell.com
6 OPERATIONS
In addition to the alarms and events listed in the above table, the following user-initiated events are also
recorded in the events history.
115
6 OPERATIONS
Failed login attempt PCN IP address change Firmware upgrade Publication period change
operation when initiated,
completed, aborted, or
failed.
Create/delete user account PCN subnet mask change DD load Publication stale limit
change
Password change PCN default gateway Device deletion PD deletion
change
User role change Disable/enable external Channel instantiation Security key transfer to the
NTP server PD for field devices/
infrastructure devices
FDN subnet mask change External NTP server Channel deletion Channel activation/
change inactivation
Enable/disable publication Enable/disable automatic Channel rename Attribute write (data may be
channel backup truncated. Maximum
reported size = 308.
Maximum old size = 256)
Enable/disable DHCP server Automatic backup Method initiation Method completion/
configuration change abortion (data may be
truncated; maximum size =
114)
Add/remove role permission Set system time Accept/reject over-the-air Restore WDM from backup
provisioning
Failure in restoring WDM from Configure a new WDM Reset WDM to factory Restart WDM
backup defaults
FDN IP address changed Write protect/unprotect Redundancy enabled/ Redundant partner PCN IP
disabled changed
116 www.honeywell.com
6 OPERATIONS
When an alarm is reported, the Event Class column displays a red alarm symbol. When the alarm returns to
normal, the alarm symbol changes to black.
The following are the events that are reported in the Alarms/Events History.
• Communications Diagnostic: Reported for events such as device offline, device joining, device online,
alarm recovery start, alarm recovery end, and so on.
• Device Diagnostic: Reported for events such as device restart, alarm recovery start, and alarm recovery
end.
• Security: Reported for security-based events.
• User actions: Reported for user actions that are captured as events. For a list of user actions that are
captured as events, refer to “Table 11: User actions logged in the Alarms/Events History tab” on
page 115.
The Alarms/Events History page is not updated automatically. Click Refresh to manually update the
Alarms/Events History page.
5 To export an alarm or event log
a Click Export Alarm Log or Export Event Log.
b On the Export Logs dialog box, click the export option using which the log needs to be exported. The
following are the available export options.
• Entire log
• From last hours: Specify the number of hours for which the log needs to be exported.
• From time period: Specify the From Date and To Date to export the log for that particular time
period. Note that this is different from the time when an event is detected which is reported in the
Event Start Time column in the Alarms/Events History page.
c Click Export.
The alarm or event log is exported in the .csv format.
117
6 OPERATIONS
118 www.honeywell.com
6 OPERATIONS
119
6 OPERATIONS
120 www.honeywell.com
7 Activate process control interfaces
Related topics
“Establishing connection between WDM and external interfaces” on page 122
“Activating HART in OneWireless Network” on page 126
“Activating Modbus in OneWireless Network” on page 133
“Activating OPC in OneWireless Network” on page 142
“About integrating OneWireless Network with Experion using the CDA interface” on page 157
“Activating GCI interface on the WDM” on page 159
“Activate ENRAF Ethernet UDP interface on the OneWireless user interface” on page 160
121
7 ACTIVATE PROCESS CONTROL INTERFACES
To connect OPC, Modbus, SmartRadar FlexLine (ENRAF), and HART interfaces to the PCN port or the COM1/COM2
of the WDM
• Connect the external interface client to the PCN port of WDM.
You can use a switch if you have multiple interfaces to connect to the WDM.
RS-232
For RS-232, select the serial port on which the serial cable is connected as COM1.
122 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
RS-485
The Modbus, HART, and SmartRadar FlexLine (ENRAF) interfaces supports RS-485. For RS-485, select the
serial port on which the serial cable is connected as COM2.
Install the Lantronix DeviceInstaller software on the HART client machine using the documentation and media
packaged with the device. For more information, refer to “Install and configure the Lantronix device” on
page 128.
123
7 ACTIVATE PROCESS CONTROL INTERFACES
124 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
125
7 ACTIVATE PROCESS CONTROL INTERFACES
Prerequisites
Ensure the following:
• The asset management system is connected to the process control network.
• The asset management system is connected to the WDM using a serial cable.
To access the field device data from the asset management system, you need to configure the HART interface
from the OneWireless user interface.
126 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
127
7 ACTIVATE PROCESS CONTROL INTERFACES
Attention
The Vendor and Model Table is pre-configured for Honeywell field devices. No configuration is required if your
device vendor and model is pre-configured. Native HART devices connected using the OneWireless Adapter do
not use the Vendor and Model Table.
128 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
129
7 ACTIVATE PROCESS CONTROL INTERFACES
130 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
3 Verify the following attributes to monitor the performance of the HART interface.
• Message Rate: Number of messages processed by the interface, per second.
• Message Rate Max: Maximum number of messages processed by the interface, per second.
• Reset Statistics: Resets all HART interface statistics.
131
7 ACTIVATE PROCESS CONTROL INTERFACES
4 For accessing the field device parameters, add HART DD files for the field devices.
After accessing the parameters, the HART Client displays the device details as follows.
132 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
133
7 ACTIVATE PROCESS CONTROL INTERFACES
Prerequisites
• Ensure that you have installed the Modbus client.
134 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
135
7 ACTIVATE PROCESS CONTROL INTERFACES
136 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
Table 14: DIAG_STATUS for all XYR 6000 field device types
You can read device vendor parameters (DEVICE_TAG.DIAG_STATUS_DETAIL_1) from Modbus client.
For example, configure UIOD_06_1FLR.DIAG_STATUS_DETAIL_1 under Holding Register.
137
7 ACTIVATE PROCESS CONTROL INTERFACES
Use the following table as a reference to interpret the data received in the Modbus client.
Table 15: DIAG_STATUS_DETAIL_1 for XYR 6000 temperature/Temp DI/Multi DI/HLAI devices
138 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
9 Expand Statistics panel, to monitor the performance of the Modbus interface. Following are parameters
available in the Statistics panel.
• Under Modbus RTU Interface and Modbus TCP Interface
– Message Count: Total number of messages processed by the interface. The count should increase
with every message sent by a Modbus client. If the count is not incrementing, it indicates that the
Modbus interface on the WDM is not receiving messages from the client.
139
7 ACTIVATE PROCESS CONTROL INTERFACES
140 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
Attention
The entire set of attributes can be pasted from Excel. Also, you can copy and paste it to Excel. This helps you to
save all the attributes in the Excel sheet.
7 Click Apply.
Attention
In the Property Panel, hover the mouse over a parameter, then a tooltip appears with the details about the attribute.
Also, this information is displayed in the Point Picker when an attribute is selected.
141
7 ACTIVATE PROCESS CONTROL INTERFACES
142 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
Prerequisites
• Install Microsoft .NET Framework 3.5 SP1 and OPC UAExpert Client in the client system.
143
7 ACTIVATE PROCESS CONTROL INTERFACES
2 On the Server menu, click Add to add the OPC server to be connected to the client.
The Add Server dialog box appears.
3 Type the Configuration Name.
144 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
4 Click the Discovery tab to view all the available servers. There is only one OPC UA server available for a
WDM, and its port number is 4840.
5 Click the Advanced tab and then type the IP address of the WDM and the port number in the Endpoint url
field.
The OPC server IP address with port number is opc.tcp://WDM IP address:4840. For example, if the WDM
IP address is 192.168.1.1, then type, opc.tcp://192.168.1.1:4840.
6 Under Security Settings, ensure that Security Policy and Message Security Mode are selected as None.
There is only one OPC UA server available for a WDM, but with multiple security modes. Multiple levels of
security are allowed in configuring the OPC UA connection to the server.
7 Under Authentication Settings, click Anonymous.
8 Select Connect Automatically check box.
145
7 ACTIVATE PROCESS CONTROL INTERFACES
146 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
147
7 ACTIVATE PROCESS CONTROL INTERFACES
12 Drag any parameter from the Address Space pane to the Default DA View to increase the load of the
network.
The OPC Statistics pane in the OneWireless user interface displays the following information about the
loaded parameters.
• Subscription Rate: Current rate of OPC subscriptions/attributes/data points that the WDM provides
every second. This must be less than or equal to 500 attributes per second.
• Subscription Rate Max: Maximum rate of OPC subscriptions/attributes/data points that the WDM
provides in a second since OPC statistics reset due to WDM reboot. This can have a higher value
because while launching the OPC client, the data rate might increase considerably.
148 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
Prerequisites
• Connect the OPC DA client system to a switch or to a system connected to the PCN
• Install the OPC Validator Client in the client system.
149
7 ACTIVATE PROCESS CONTROL INTERFACES
150 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
151
7 ACTIVATE PROCESS CONTROL INTERFACES
3 Double-click OPC DataAccess Servers Version 2.0 and select OpcDa.OneWirelessGW.ComServer from
the list, and then click Connect Server….
4 Once the server is connected, click Close.
The OPC Server List dialog box closes.
5 In the OPC Validator window, select OpcDa.OneWirelessGW.ComServer.
6 Click Data > Browse Server Address Space, and then click Browse Server Address Space All.
The Address Space appears on the lower pane.
7 In the upper pane, right-click OpcDa.OneWirelessGW.ComServer, and then click Add Private Group.
The Add Private Group dialog box appears.
152 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
153
7 ACTIVATE PROCESS CONTROL INTERFACES
To add individual parameters for a device, expand the device, right-click the parameter, and then click Add
Item to Group_OW.
11 In the upper pane, expand Group_OW to view the items in your group.
12 Click Tags – All to view all the tags.
13 Navigate to the desired value. Identify the OPC item that represents the desired value.
154 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
Perform the following steps to edit parameters from OPC DA client. Note that you can only edit the
parameters whose access rights are displayed as RW in the Rights column of the OPC Validator.
• In the OPC DA client, click the Tags — All tab.
• Right-click the parameter that you have added, and then click Async> Write Item.
The Write Async Item Value dialog box appears.
• In the Raw field, type the required value.
You can only edit the mode for all the device types and the output value of the Multi AI DI DO devices.
• Click OK.
155
7 ACTIVATE PROCESS CONTROL INTERFACES
156 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
7.5 About integrating OneWireless Network with Experion using the CDA
interface
OneWireless Network can be integrated with Experion PKS system using the CDA interface available on the
WDM. To establish communication between the Experion system and the OneWireless Network, you must
connect the WDM to the Experion network. For more information about connecting WDM with the Experion
system, refer to the section “Establishing communication between OneWireless Network and Experion system”
on page 24.
After connecting the WDM to the Experion network, you need to configure the OneWireless Network
components such as WDM and field devices using the Control Builder. For more information about configuring
the OneWireless Network components using Control Builder, refer to the Experion PKS OneWireless
Integration User’s Guide.
After the communication between the Experion system and the OneWireless Network is established, the CDA
parameters on the OneWireless user interface provides you information about the WDM state, CDA statistics,
and the peer connections of the WDM. Following are the CDA parameters that are available on the user
interface.
157
7 ACTIVATE PROCESS CONTROL INTERFACES
For more information about the CDA parameters, refer to the OneWireless Parameter Reference Dictionary.
158 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
7 Verify the following attributes to monitor the performance of the GCI interface.
• Message Rate: Number of messages processed by the interface, per second.
• Message Rate Max: Maximum number of messages processed by the interface, per second.
8 Click Reset Statistics to reset all the GCI interface statistics.
159
7 ACTIVATE PROCESS CONTROL INTERFACES
4 Under the Ethernet/UDP Interface Options, the UDP port number of the port on which the WDM is
connected is displayed.
5 Click Apply.
Prerequisites
Ensure the following:
• The SmartRadar FlexLine field devices are connected to the WDM using a serial cable.
• The SmartRadar FlexLine field devices are joined in the ISA100 Wireless network.
• The GPU address and the FlexConn address configured for a SmartRadar FlexLine field device should be
unique for each device in the network.
For more information regarding the GPU address and the FlexConn address, refer to the section “Configure
SmartRadar FlexLine field device interface”.
• If RS-232 serial communication is required, then connect the RS-232 serial cable between the COM1 port of
the WDM and the client .
• If RS-485 serial communication is required, then connect the RS-485 serial cable between the COM2 port of
the WDM and the client .
160 www.honeywell.com
7 ACTIVATE PROCESS CONTROL INTERFACES
161
7 ACTIVATE PROCESS CONTROL INTERFACES
3 Verify the following attributes to monitor the performance of the ENRAF interface.
• Message Rate: Number of messages processed by the interface, per second.
• Message Rate Max: Maximum number of messages processed by the interface, per second.
4 Click Reset Statistics to reset all the ENRAF interface statistics.
162 www.honeywell.com
8 Administration
Related topics
“Administering users” on page 164
“Downloading support software” on page 169
“Upgrading device firmware” on page 170
“Configuring system configuration backup” on page 174
“Restoring the system configuration from a backup” on page 176
163
8 ADMINISTRATION
Related topics
“About users and user roles” on page 164
“Create user accounts” on page 165
“Edit user account” on page 166
“Delete user account” on page 166
“Change password” on page 167
“Reset password” on page 167
“Change user role” on page 167
“Manage user roles” on page 168
164 www.honeywell.com
8 ADMINISTRATION
Attention
The Provision WDM function also enables you to configure the redundant related parameters.
165
8 ADMINISTRATION
5 Click Save.
6 Click Close to close the Manage Users dialog box.
166 www.honeywell.com
8 ADMINISTRATION
167
8 ADMINISTRATION
168 www.honeywell.com
8 ADMINISTRATION
169
8 ADMINISTRATION
Related topics
“Upgrading the WDM firmware” on page 170
“Upgrading the FDAP/access point firmware” on page 171
“Upgrading the field device firmware” on page 172
Attention
Sync must be disabled on a redundant WDM to allow WDM upgrade. If WDM upgrade is initiated on a WDM when
sync is enabled an error is displayed. You must disabled the sync from WDM PP and again re-initiate the WDM
upgrade.
CAUTION
• Upgrading the WDM firmware makes the WDM offline for some time. During this operation, all the devices
drop and join the network again.
• Once initiated, you cannot abort the firmware upgrade operation.
• The WDM must not be turned on while the upgrade is in progress.
The steps for upgrading the WDM from R202 to R210 and then from R210 to R220 are common.
Prerequisites
Ensure that the speed/duplex setting for the network adapter of the computer is set to Auto.
170 www.honeywell.com
8 ADMINISTRATION
3 Click Browse to navigate to the directory location of the firmware file and click Open. The WDM firmware
file has a .tar.gz extension.
The WDM Update dialog box displays the upload status. Once complete, the Firmware File box displays
the uploaded firmware file.
4 Click Update.
The firmware upgrade starts and once complete, the user interface displays a message indicating the result of
firmware upgrade operation.
Attention
At times, the update may take longer than expected and the result of the upgrade may not be displayed. Instead, a
“Page not available” error may appear. In such cases, wait for a minute and then redirect the browser to “https://
<ipaddress>/restartzfs.html” for viewing the result. Do not remove or reboot the WDM during the upgrade
process.
After the WDM upgrade from R210 to R220 is complete, the WDM reboots automatically.
171
8 ADMINISTRATION
3 In the Available Firmware Files list, select the required firmware upgrade file.
By default, the firmware upgrade file appears in the list. If the file is not available in the list, perform the
following steps to open the firmware file.
a Click Add to browse to the directory location of the firmware upgrade file.
b Click Open.
4 Click Upgrade.
The Firmware Upgrade Status dialog box appears. The Progress column displays the progress of the
upgrade.
Attention
• To abort any firmware upgrade operation, click the Abort Upgrade icon adjacent to the upgrade status.
• To remove the devices for which the firmware upgrade has been completed, click the Clear Upgrade icon
adjacent to the upgrade status.
Attention
It is recommended that you select and accept only three devices at a time.
2 On the ribbon bar, in the Upgrade group, click one of the following icons, as required.
172 www.honeywell.com
8 ADMINISTRATION
Attention
To initiate the firmware upgrade of the HCI-1WL (CAN-1WL) board using the Application firmware, the SD
card must be inserted in the HCI-1WL (CAN-1WL) board. Also, the SD card should not be write protected.
173
8 ADMINISTRATION
Related topics
“About system configuration backup” on page 174
“Configure manual backup” on page 174
“Configure automatic backup” on page 174
174 www.honeywell.com
8 ADMINISTRATION
175
8 ADMINISTRATION
Attention
After restoring the system configuration, the default administrator password resets to the default password,
“password.” All other users’ password remains unchanged.
6 Select the required backup file from the list of available backups, and then click View Details to view the IP
addresses and redundancy information.
176 www.honeywell.com
8 ADMINISTRATION
Attention
• The network address of the WDM when a backup is performed is displayed at the bottom of the page. After
completing the restore, you can access the WDM using this IP address.
• Reconfigure the network settings of the computer to access the user interface using the IP address displayed on
the Restore WDM from Backup page.
7 Click Restore.
8 Click OK on the Browser Redirect dialog box.
The system configuration restores, and the Login page appears. The WDM restarts after the restore
operation. It might take a minute to complete the restart and the login page to appear.
9 Type the default User ID and Password or use the logon credentials configured at the time when the backup
file was created.
177
8 ADMINISTRATION
178 www.honeywell.com
9 Troubleshooting and maintenance
Related topics
“Replacing devices” on page 180
“Removing devices” on page 182
“Resetting/removing WDM” on page 183
“Restarting devices” on page 184
“About NTP status” on page 186
The NTP Status panel in the WDM Properties Panel displays a number of NTP process attributes, which
are mostly useful for debugging purposes.
“Generating reports” on page 188
“Exporting and saving system logs” on page 193
“Reporting anomalies” on page 194
179
9 TROUBLESHOOTING AND MAINTENANCE
Prerequisites
• Ensure that the failed device is offline and that it is not deleted.
• Ensure that the new device’s tag name, type, radio vendor, and radio model is read by the WDM.
• Ensure that methods are not running for any of the channels of the new field device.
• Ensure that new device's firmware is not undergoing any upgrade operation.
• Ensure that new device's channels have been read by the WDM.
To replace devices
1 Provision the new device to allow it to join the network.
For more information, refer to the section “Provision the devices using Provisioning Device handheld” on
page 60.
2 Perform one of the following:
• For replacing a field device with instantiable channels, verify that the new device’s instantiable channels
are identical to that of the failed device.
• If not, perform channel instantiation to make the channel configuration identical to the failed device.
For more information, refer to the section “Configure channel instantiation” on page 86.
3 To replace a field device, set the channel to OOS mode as follows:
a On the Selection Panel, select the field device channel.
b On the Property Panel, expand Mode.
c In the Target list, click OOS and then click Apply.
The channel icon appears as blue indicating the OOS mode.
4 On the Selection Panel, select the newly added device.
5 Drag the new device icon and drop it on the failed device on the map.
The Device Replacement dialog box appears.
6 Click Replace failed device <device name> with <new device name>.
7 Click OK.
180 www.honeywell.com
9 TROUBLESHOOTING AND MAINTENANCE
The Device Replacement Status dialog box appears indicating the progress of replace operation. The status
bar also displays the status. If you close the Device Replacement Status dialog box, click the Device
replacement in progress pane in the status bar to open the dialog box.
8 After the device replace operation is complete, the Device Replacement Status dialog box displays the
result.
Attention
If a device replace operation completes with errors, it implies that one or more attributes of the device is not
restored successfully. In this case, manually inspect the device and channel configuration from the Property Panel,
and correct any incorrectly configured attribute.
181
9 TROUBLESHOOTING AND MAINTENANCE
To remove a device
1 On the Selection Panel, select the devices that you want to delete.
If you are deleting an online device, change the channel mode to OOS for all the channels.
2 On the ribbon bar, in the Provisioning group, click Delete.
The Delete Devices dialog box appears.
3 Click Delete.
On completion, the Progress column in the Delete Devices dialog box displays the status as complete.
4 Click Close.
182 www.honeywell.com
9 TROUBLESHOOTING AND MAINTENANCE
CAUTION
This operation results in significant changes in the system configuration. Honeywell recommends you to perform
this operation only when there is a definite requirement.
To delete/reset a WDM
1 On the Selection Panel, select the WDM.
2 On the ribbon bar, in the Provisioning group, click Delete.
The Delete Devices dialog box appears.
3 Click Delete.
On completion, the Progress column in the Delete Devices dialog box displays the status as complete.
4 Click Close.
This resets/removes the WDM.
5 Use default FDN or PCN IP address to access WDM after the WDM is reset to defaults.
6 Restart the Web browser to run the First Time Configuration Wizard.
You can either configure the WDM using the First Time Configuration Wizard or restore the system
configuration using the latest available backup. If you are configuring the WDM using the First Time
Configuration Wizard, you need to transfer new provisioning keys to the Provisioning Device handheld
and provision all the devices in the network.
183
9 TROUBLESHOOTING AND MAINTENANCE
To restart a WDM
1 On the Selection Panel, select the WDM.
2 On the Property Panel, expand Device Management.
184 www.honeywell.com
9 TROUBLESHOOTING AND MAINTENANCE
185
9 TROUBLESHOOTING AND MAINTENANCE
186 www.honeywell.com
9 TROUBLESHOOTING AND MAINTENANCE
Peer rejected
The NTP process determines the time quality of the server over several communication packets based on
various time and frequency measurements. Based on these measurements, the NTP process may reject a server
but still continue to communicate with it and perform the time measurements. Until the server’s time quality
improves, the NTP process keeps the server marked as rejected. In the NTP Status panel, under Peer status
section, the Peer Selection status is set to Reject. When a server is in rejected state, the NTP process does not
try to sync time from the server.
Peer selected
The NTP process may reject a server for several reasons. For example, the server itself may not yet have
synchronized to the root time server. While the server is rejected, the NTP process keeps performing the time
and frequency measurements with the data received from the server. When the reference time quality improves,
the NTP process selects the server as a system peer and starts synchronizing time with the server. In the NTP
Status panel, under Peer status section, the Peer Selection status is set to SysPeer.
Mean offset
The NTP process monitors time from a server selected as a system peer and calculates how much correction
should be made to the system time. In the NTP Status panel, the Mean offset indicates the additional remaining
correction to the system clock. A positive value indicates that the system clock is behind the reference clock. As
the NTP process slowly corrects the system time, the system clock slowly approaches the reference clock and
the mean offset reduces.
Time synchronization
In the NTP Status panel, under the System status section, the Mean frequency offset field indicates the periodic
correction applied to the system clock. Positive values make the clock go faster while negative values slow it
down. When the NTP process starts synchronizing with a server, depending on how far the two clocks are, it
may set the frequency offset to the maximum value (+/-500 ppm). This is unusually high for a good clock and is
an intermediate value. ISA100 network devices correct their clocks at a maximum rate of 60 ppm. If the
WDM’s clock is corrected at a higher rate, the ISA100 network devices may further apart in time, resulting in
devices reporting a clock drift alarm. The WDM generates an NTP frequency error alarm when the frequency
offset is > 60 ppm. As the WDM’s system time converges and the offset reduces, the frequency offset gradually
reduces to a more realistic value. The NTP frequency error alarm returns to normal when the frequency offset
reduces to below 30 ppm. The NTP process adjusts the clock in small steps so that the time-scale is effectively
continuous and without discontinuities. This makes clock correction slow. In a system with a redundant or
backup WDM, the backup WDM uses the primary WDM as its time server. If the primary WDM is configured
to use an external NTP server, it may take some time for the primary WDM to synchronize with the NTP server
and then the secondary WDM will synchronize, after some more time, with the primary WDM’s time.
187
9 TROUBLESHOOTING AND MAINTENANCE
• Device Health Overview: This report lists all the devices with wireless network disconnection and alarms.
188 www.honeywell.com
9 TROUBLESHOOTING AND MAINTENANCE
• Device Summary: This report provides a summary of each of the device that is configured in the network.
The report does not display the details of the devices that are filtered out using the Filter option in the
ribbon bar.
• Device History: This report lists all the device status changes. For example, status change from online to
offline device, routing to time synchronization, non-redundant connection to redundant connection.
189
9 TROUBLESHOOTING AND MAINTENANCE
• Connection Summary: This report provides a summary of current status of device connections in the
network, redundancy state, and lists all connections with a poor or unacceptable signal strength and quality.
The RSQI value when less than 128 results in poor or unacceptable signal quality.
• Connection History: This report lists all the history of connection changes. For example, change of RSQI,
RSSI, transmit fail ratio.
190 www.honeywell.com
9 TROUBLESHOOTING AND MAINTENANCE
191
9 TROUBLESHOOTING AND MAINTENANCE
• Select the Include column headers in exported file check box to include the column headers in the
exported file format.
192 www.honeywell.com
9 TROUBLESHOOTING AND MAINTENANCE
Attention
For WDMS configured as redundant, export the system logs from both WDMs when reporting an anomaly or
requesting clarification.
193
9 TROUBLESHOOTING AND MAINTENANCE
194 www.honeywell.com
10 Notices
Other trademarks
Microsoft and SQL Server are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Trademarks that appear in this document are used only to the benefit of the trademark owner, with no intention
of trademark infringement.
Third-party licenses
This product may contain or be derived from materials, including software, of third parties. The third party
materials may be subject to licenses, notices, restrictions and obligations imposed by the licensor. The licenses,
notices, restrictions and obligations, if any, may be found in the materials accompanying the product, in the
documents or files accompanying such third party materials, in a file named third_party_licenses on the media
containing the product, or at http://www.honeywell.com/ps/thirdpartylicenses.
195
10 NOTICES
196 www.honeywell.com
10 NOTICES
197
10 NOTICES
198 www.honeywell.com