IN S T RU C T I O N

The SWORKz S35-4 1/8 Nitro is designed for pure racing. The geometry of the car provides optimized
corner speed compared with easy handling and maximum traction.
The S35-4 features a T7075 hard anodized and lightened aluminum chassis with a wide layout that was
tested for a long time by our factory pilots to guarantee the best performance.
The totally new developed HET differentials are included too and provide a traction, that is not possible
with old systems.
The new S35-4 comes with a lower shock layout in front and rear and the construction of the shocks is
adapted to that new optimized layout. The fixed shock spring plates will make it almost impossible to lose
them anymore.
The steering geometry, with new Ackerman and steering plates, gives the driver the feeling of total control
over the S35-4.
With the toe in plates, which now contain square inserts, you can adjust the geometry of your SWORKz
S35-4 to fit to every track layout and track condition. Lower arms in front and rear are made of a newly
developed composite material and fit exactely to the new chassis geometry. Side guards were redesigned
in the same way.
With the new lightened wing support you can adjust position and angle of the wing to give your SWORKz
S35-4 the perfect balance on the track. Together with the optimized new body shell, the aerodynamic
system is working perfectly together.
Another new development in our SWORKz S35-4 is the totally new rear hub. Composite material combined
with Carbon plates gives you the possibility for various setups. The newly developed Composite material
is working perfectly together with the HET differentials to provide maximum traction.
There many more small changes and smart ideas in your new SWORKz S35-4, that make the car being a
real winner.
The secret of a modern racing car is the possibility to adapt the setup to every track for top pilots but also
have a standard setup that works on most tracks for hobby pilots.
And your SWORKz S35-4 is having these two characteristics in perfection.
The SWORKz development team focused on using materials, corresponding to the highest quality
standards, when designing the car. You will find only 100% SWORKz quality in the S35-4 kit.
Congratulations on your purchase of the new SWORKz S35-4 1/8 scale off-road racing buggy pro kit and
thanks for trusting in SWORKz.
Please read this manual carefully, before you start to build and drive your SWORKz S35-4. This manual
contains step-by-step instructions to helping you completing, preparing and fine tuning your buggy for
racing. Updates, setups, and product news will be posted on all SWORKz digital media.
As always, if you should ever have any questions or need help with your SWORKz products, please feel
free to contact our official SWORKz dealers and distributors.
S35-4 Kit Features :
• New T7075 Hard Anodized, Lightend Aluminium Chassis • New Lightweight Wing Mount
• New Wide Chassis Design • New Side Guards
• New Lower Shock Towers • New Lower Front and Rear Arms
• New Shorter Shock Bodies • New Body Posts Front and Rear
• New Shorter Shock Shafts • New Composite Rear Hubs with Carbon Plates
• New Shock Caps • New Multi Adjustable Ball System for Rear Upper Arms
• New Shorter Front Shock Springs • New Anticlock Screws for Shocks
• New Fixed Shock Spring Holder • New Aerodinamically Optimized Body Shell
• New 3mm Updated Rear Shock Studs • 3 HET Differentials Included
• New Ackerman Plate • 2 Front Chassis Braces Included
• New Steering System • Black Competition Shock Springs Included
• New Servo Saver Aluminium Part • Adjustable Wing Position
• New Servo Saver Fixable Nut • Adjustable Wing Angle
• New Servo Saver Plate • More Balance Weight Positions
• New Servo Saver Post Locking Design • Stronger Downstop Area
• New Steering Balls • Optimized Composite Material
• New Steering Knuckle Plates • Aluminium Parts in T7075
• New Updated Toe In Plates with Square Inserts
2
 Specification
Length: 510mm
Width: 308mm
Height: 220mm
Ground Clearance: 65mm
Wheelbase: 325-330mm
Track: F:304mm / R:306mm
Gear Ratio: C:47/13T, F/R:43/13T
Weight: 3400g(Race condition)

WARRANT Y

Your SWORKz S35-4 kit warranty covers workmanship and manufacturing

defects of the original and unmodified parts. Warranty claims resulting from
crashes, abuse, improper operation, improper mounting, improper adjustment or
lack of maintenance will not be honored.

Contact your local hobby shop or SWORKz distributor for all claims and
questions. Claims must be well documented. All Claims are subject to expert
examination approval by SWORKz.

3
IN D E X

INSTRUCTION 2

Warranty 3

INDEX 4

Required Equipment for Operation 5

Operation Guide 6

Assembly Steps 7-37

Set-up Sheet 38-39

S35-4 Key No. List 40-41

S35-4 Spare Part No. List 41-42

S35-4 Option Part No. List 43

Explosion view with spare parts number 44-47

End cover 48

This radio controlled racing car is not a toy!

This high-performance R/C model is recommended for ages 14 and older.

4
R e q u i re d Equ ip m e nt fo r O p erat io n
Radio Gear Nitro fuel
Stick Type Receiver batteries

We recommend that you use fuel

containing 20~25% nitro.

Throttle servo

On/Off Switch

Receiver

Wheel & Trigger Type

Steering servo
Fuel bottle

Engine Recommended Engine Starting Equipment

Exhaust header
SW-950001A
SWORKz BB80 1/8 Off Road Starter
Box (Buggy Type) ST-3 Turbo Plug
ST-4 Turbo Plug

Glow Plug
SP-80101
EFRA2042

Starter box

Tools Recommended

Long nose pliers Side cutter

1.5mm
Paint
Curved scissors

2mm

2.5mm Modeling knife

Screwdriver Instant cement Thread lock Double-sided tape

Screwdriver

Included items
Glow plug wrench

Hex wrench

1.5mm
Grease
2mm

2.5mm

5
O p erati on G u id e

Assemble front Assemble in the Assemble both left Assemble for Assemble for
and rear specified order and right sides 2 sets 4 sets

overturn Thread Locking Grease Pure Silicone Oil Air filter oil
Compound

S afet y Pre c au t io ns

The SWORKz S35-4 is a high performance radio control model which needs to be operated
with caution and common sense.
The S35-4 Kit is not intended for children under the age of 14 without adult supervision.
SWORKz shall not be held liable for any loss or damages, whether direct, indirect, act of
nature, arising from the abuse or misuse of this product or any other product required while
operating this model.
- The nitro fuel can be dangerous if improperly handled.
- Always keep your nitro fuel in a cool area and never use near flame, sparks, or while
smoking.
- Keep your nitro fuel, and all other flammables, out of the reach of children.
- Always run your model in a well ventilated area outdoors. Never run your model indoors.
- After running your car, all parts of the engine and exhaust can become extremely hot. Be
careful not to touch these parts especially when refueling, or making repairs.
- This model is controlled by your radio controller and is sometimes vulnerable to interference
from many outside sources. This interference can cause a loss of control so it is necessary to
operate this model in an open area to avoid personal, or property damage. Always ensure
turning on your radio first.
- Keep all the parts included in the package out of reach of children.
- This model contains many fast rotating parts. Never touch them during operation.
- Follow the instructions included with your radio gear.
- Never operate your model near people or property. The speed of this model has the
potential to injure and or damage people and or property.
- Always use original SWORKz spare parts and option parts.
- Always ensure that the buggy is in proper working condition before use.

6
 BAG B 1 330015

330015
x4
Pin M2.2x9.9mm
328001
101039
338024 338027
400002
x4
O-ring S5 4.8X1.5

116006R
400002

101039
x2
Washer 5x12x0.3 210091
116006R
330015

338027
Remember to apply a light coat of
grease to the o-ring, then slide it over
328001 400002 the shaft of the out drive and seat it in
the diff case.
116006R 101039 Insert the pin through the hole in the
x4
Ball Bearing 8x16x5mm (Red Rubber Case) diff case and through the hole in the
shaft of the out drive.

2
108003

108003

108003
x8
M3x10mm FH/ST HEX Screw

338025
x4
S35-3W Bevel Gear Shaft
610023

328001

101004
101004
x8 101004
Washer 3.5X10X0.2mm

328001

101004
328001 338025

101004

Fill the differentials

OK! NG! with oil up to 80%
above the satellite
gears.
Put the SWORKz
Diff. Oil 7000cps
for the front Diff.
and 3000cps for the
rear Diff.

7
 BAG C 3 338040
330015
328001

330015
x2
Pin M2.2x9.9mm
116006R

101039
400002
x2 338028
O-ring S5 4.8X1.5 400002

338028 210079A

116006R
x2
Ball Bearing 8x16x5mm (Red Rubber Case)
330015 116006R

Remember to apply a very light

coat of grease to the o-ring, then
101039 slide it over the shaft of the out
x2 400002 drive and seat it in the diff case.
Washer 5x12x0.3
328001 Insert the pin through the hole
101039 in the diff case and through the
hole in the shaft of the out drive.

4 108001

108001
x4
M3x12mm FH/ST HEX Screw
108001

338025
x4
S35-3W Bevel Gear Shaft

101004
x4
Washer 3.5X10X0.2mm 610020
101004
101004

328001

328001 338025

101004

Fill the
OK! NG! differentials
with oil up to
101004 80%
above the
satellite gears.
Put the
SWORKz
Diff. Oil
7000cps for
the center Diff.

8
 BAG D 5 Pro Tip:
Before installing the M5x4 set screw (104010),
remember to clean the set screw and center driver joint (330661A) first.
Then apply TLC on the set screw.

338023

106019R

338011

104010
x1
106019R
M5x4mm Set Screw (Flat Bottom) 228001(#8 #9 #10)

330661A
108001 2503261A
x4
M3x12mm FH/ST HEX Screw

228001(#8 #9 #10)

116019R
x2
Ball Bearing 5x13x4mm (Red Rubber Case) 338059
104010

Note:
The aluminum front lower arm holder (338059) can offer 0° or 1°
kick-up for your front lower suspension.
101018 You may use the inserts 228001(#10)
x4 kick-up or 228001(#9) to get 1° for your front lower suspension. 108001
SHIM 13x16x0.2mm

338011
x1
S35 series Pinion Gear Stopper (5x7x5.1mm)

101018

101018

2503261A
108001
Note:
101018SHIM 13x16x0.2mm
Please use 13x16x0.2mm shims to adjust the play between the crown gear and pinion gear.
Standard suggestion is 1pc shim on the diff crown gear side and 3 pcs on the other side.

9
 6 Pro Tip:
Before installing the M5x4 set screw
(104010), remember to clean the set screw
338023 and center driver joint (330661A) first.
106019R Then apply TLC on the set screw.

338011 330661A
108001 106019R
x4
M3x12mm FH/ST HEX Screw
228001(#2 #3 #4)

104010 338049
x1 2503261A
M5x4mm Set Screw (Flat Bottom)

104010
228001(#2 #3 #4)
116019R
x2
Ball Bearing 5x13x4mm (Red Rubber Case)

101018

108001
101018
x4
SHIM 13x16x0.2mm

338011
x1
S35 series Pinion Gear Stopper (5x7x5.1mm)

101018

2503261A
Note: 108001
101018SHIM 13x16x0.2mm
Please use 13x16x0.2mm shims to adjust the play between the crown gear and pinion gear.
Standard suggestion is 1pc shim on the diff crown gear side and 3 pcs on the other side.

BAG E1 7
330136

Right

2501121C

Left 330134
228005S-F

106005
106005
x2 228005S-F
M3x15mm Hex Socket OH/TP Screw

106021A
M4x10mm Hex Socket OH/TP Screw
X2 106021A

10
 BAG E1 8
108008
x2
M3x35mm FH/ST HEX Screw

101020A
x2
3mm Countersunk Washers (GM)

228001(#5 #6 #7)

338056
338058

118008 228001(#5 #6 #7)

101020A

338056
x2
S35-4 Series Lower Arm Hinge Pin (68.5mm)

9 2503261A

Pop in the Stabilizer Guide.

104004
x2
M3x3mm Set Screw

104004

104004

115008A (2.3mm)
or
115035A (2.2mm)

11
 BAG E1 10

104005
x2
M3x4mm Set Screw

106013
x2
M2.5x8mmH ex Socket OH/TPScrew

106013
104005

11
Note:
The aluminum front upper arm holder (338057) can offer either
0° or + -1° kick-up for your front upper arm suspension.
You may use the inserts 228001(#13) to get 0° kick-up
228006 or 228001(#12) to get +-1° for your front upper suspension.

106002 x1
M3x10mm Hex Socket OH/TP Screw

108006
108006
108003 108003
x2
M3x10mm FH/ST HEX Screw
340017

108006
M3x8mm FH/ST HEX Screw x2

338057

106002

228001(#11 #12 #13)

12
 BAG E1 12 PRO TIP:
The S35-4 Front Upper Arm Adjust Inserts
can give different steering adjustments (Ackerman).
Put all inserts behind the front upper arms, you will get faster steering response.
Otherwise put all inserts in front of the upper arms,
108001 you will get more stable steering response.
x4
M3x12mm FH/ST HEX Screw Try to use 2503260-1 or 2503260-3 to adjust the front upper arm position.

2503260(#1 #2 #3 #4)
106015
x2
M3x5mm Hex Socket OH/TP Screw

330119
x2
Front Upper Arm Hinge Pin

330119

338054
2503260(#1 #2 #3 #4)
228001(#14 #15 #16)

106015 330119

106020
228001(#14 #15 #16)
106020
106015

340003
108001

Note:
2503260-1
S35-3 Front Upper Arm Adjust Insert (0.9mm)
2503260-2 2503270-01
S35-3 Front Upper Arm Adjust Insert (1.0mm)
2503260-3
S35-3 Front Upper Arm Adjust Insert (1.1mm)
2503260-4
106020
S35-3 Front Upper Arm Adjust Insert (2.0mm) x10
M2.5x5mm Hex Socket OH/TP Screw

13 330136

106005
x2
M3x15mm Hex Socket OH/TP Screw

2501121C

106021A
X2 330134
M4x10mm Hex Socket OH/TP Screw

106005

228005S-(R)

106021A

13
 BAG E1 14 108005

330399B
106002
x1
M3x10mm Hex Socket OH/TP Screw

228006
108001 338050
x4
M3x12mm FH/ST HEX Screw

108005
x2
M3x14mm FH/ST HEX Screw

106002

108001

15 PRO TIP:
The S35-4 Aluminum Rear Lower Fully
Adjustable Toe-In Block (338014) can use 3
types of square inserts to get 1.0/2.0/3.0 3
108008
x2 different toe in angles. Also plus 3 different
M3x35mm FH/ST HEX Screw
rear lower arm kick up degrees.

338056

338056
338014
108008
228001(#2 #3 #4) 228001(#2 #3 #4)

338056 OPTION:
x2 228001-2 S35-4 Series Rear Lower Arm Holder Square Insert (+1/+1)
S35-4 Series Lower Arm Hinge Pin (68.5mm)
228001-3 S35-4 Series Rear Lower Arm Holder Square Insert (0/+1)
228001-4 S35-4 Series Rear Lower Arm Holder Square Insert (0)

14
 BAG E1 16 2503261A

Pop in the Stabilizer Guide.

104004
x2
M3x3mm Set Screw

104004

104004

115005 (2.8mm)
or
115006 (2.6mm)

17
104005
x2
M3x4mm Set Screw

106013
x2
M2.5x8mmH ex Socket OH/TPScrew

104005

104005
106013

15
 BAG E3 18 106002

106002
x4
M3x10mm Hex Socket OH/TP Screw
Right 338051

330252

2503260-04

330118A
Left

330118A 2503264A

330252

2503260-04
Screw and adjust 330118A Knuckle
Pivot Ball Nut so as the pivot ball can
be moved smoothly.

19
Left
116006R
x4
Ball Bearing 8x16x5mm (Red Rubber Case)

104010
x2
M5x4mm Set Screw (Flat Bottom)

210046
330124
330124
x2
Pin M3.0x16.8mm

330121B

116006R

101018 Note:
x2 101018SHIM 13x16x0.2mm
SHIM 13x16x0.2mm
116006R Please use 13x16x0.2mm shims to adjust the
Right gap between the wheel hub and wheel knuckles.
101018 Standard suggestion is 1pc shim on the outside
104010 between 8x16x5mm ball bearing and knuckle.
If the wheel hub still has big play with knuckle,
please try to put another shim in another side
between ball bearing and knuckle.

16
 BAG E3 20

330117A

330117A

BAG E2 21 116004R
106007
101021
338043
103001
x2
M3 Nut Lock 106014
117003
610019
101021 101021
x2
M3x8xT1mm
338053 115004A
117003

117003
x4
Flange Ball Bearing 3x6x2.5mm
117003 338052

106007
x2
M3x12mm Hex Socket 116004R
OH/TP Screw(HT)
117003
2501122B

116004R
x2
Ball Bearing 6x10x3mm (Red Rubber Case)

106014
x1 330114A
M2x6mm Hex Socket OH/TP Screw 103001

103001
2501122B

17
 BAG E2 22
108003

108003
x2
M3x10mm FH/ST HEX Screw

116004R
x2
Ball Bearing 6x10x3mm (Red Rubber Case)

101019
x1
SHIM 6.0x10.0x0.2mm

101019

116004R

338048
116004R

338048

BAG E3 23
Left

104010
x2
M5x4mm Set Screw (Flat Bottom)

210046

330124
x2
Pin M3.0x16.8mm
228002-1 340016 106009

Right
116006R

340016 228001(#17 #18)

116006R
x4
Ball Bearing 8x16x5mm (Red Rubber Case)
330124
103001

106009 330121B
x4
M3x25mm Hex Socket OH/TP Screw 228001
(#17 #18) 116006R 104010

PRO TIP:
103001 The new multi adjustable rear hub can be set
x4
M3 Nut Lock to a wider or a narrow configuration using the
inserts 228001 (#17 #18)

18
 BAG E3 24 PRO TIP:
The base set up is always by using 2-3mm inserts on
the rear of Hub Carriers Hinge Pins.
2503260 The wheel base length should be around 327-328mm.
(#5 #6 #7)
2503260
(#5 #6 #7) 103001

330782
103001

103001
x2
M3 Nut Lock

330782 330782
x2
Rear Hub Carriers Hinge Pin with Nut

2503260 (#5 #6 #7)

25 Shorty Upper Arm Linkage Set-up

22.85 mm

330123A
x2 228006-5
Rear Upper Sus. Arm Turnbuckles

330123A

330125

2501121C

2501121C
338070B

Longer Upper Arm Linkage Set-up

9.85 mm

19
 BAG E3 26
Longer Upper Arm Linkage Set-up

106002 106002
x2
M3x10mm Hex Socket OH/TP Screw

106009
M3x25mm Hex Socket OH/TP Screw
x2 228001

103001
x2
M3 Nut Lock
106009

106002

103001
228001

106009

Shorty Upper Arm Linkage Set-up

103001

27 103001
228003A
228003A(#3)
108019
228003A(#3)

103001
x6
M3 Nut Lock

106003
x4
M3x16mm Hex Socket OH/TP Screw 228003A

103001
108019
x2
M2.6x6mm Flat Head Screw - Hex Socket

103001

106003
228003A

OPTION:
228003A(#3) S35 Series Integrated Wing Mount Spacer (0 Degree)
228003A(#4) S35 Series Integrated Wing Mount Spacer (1 Degree)
228003A(#5) S35 Series Integrated Wing Mount Spacer (2 Degree)

20
 BAG F 28 104004

SWC-330106

108006

106007
x4
M3x12mm Hex Socket OH/TP Screw(HT)
108006

104004 330090
x2
M3x3mm Set Screw

116009

108006
x4 116009
M3x8mm FH/ST HEX Screw
2501124 330647
115098
210043 104004

116009 330104
x2
Ball Bearing M5x8x2.5mm 330104

106007 210043
115098

29 106009 106009

106009
x4
M3x25mm Hex Socket OH/TP Screw

SWC-330580

SWC-330580

2501124

2501124

21
 BAG F 30 108007

228004
108007
x10
M3x6mm FH/ST HEX Screw 338047A

228004

108007
108007

31
108003
x2
M3x10mm FH/ST HEX Screw

108010
M4x10mm FH/ST HEX Screw
x2 Front
Top View
Rear

108012
x4
M4x16mm FH/ST HEX Screw

2501097B

108012

108010
108012 108003

22
 BAG F 32
228002-2
108003
x3
M3x10mm FH/ST HEX Screw

108010
x4
M4x10mm FH/ST HEX Screw 108003

330767A

108003
108010

33

108012
x4
M4x16mm FH/ST HEX Screw
2501529A

103001
106006
x1
M3x20mm Hex Socket OH/TP Screw

106006
103001
x1
M3 Nut Lock

330663A

108003
x2
M3x10mm FH/ST HEX Screw

108012
108012

108003

23
 BAG G 34 106008
106008
106003
106003
106008
x4
M3x12mm Hex Socket OH/TP Screw

Servos are not

106003
x4 included in the kit.
M3x16mm Hex Socket OH/TP Screw

2503262

2503262

2503262

35 106002

103001 Receiver and switch are

x2 The switch is not
M3 Nut Lock not included in the kit.
included in the kit.

106002
x2
M3x10mm Hex Socket OH/TP Screw

Laps transponder is not

included in the kit.

103001

24
 BAG G 36 108006

108006
108006
x4
M3x8mm FH/ST HEX Screw

2503262

104004
M3x3mm Set Screw
x1 37
Li-ion
Size:18500
106001
x3
M3x8mm Hex Socket OH/TP Screw
106001
106001
Battery is not
included in the kit.
2503262
or 106001

200193
Li-ion
Size:18650

104004

25
 BAG G 38
108006
x6
M3x8mm FH/ST HEX Screw

108006
108006
108006

BAG G 39 103001 OPTION:

SW-338078-25 SWORKz Uni-Design 2-Way System Aluminum Steering Servo Horn 25T
SW-338078-23 SWORKz Uni-Design 2-Way System Aluminum Steering Servo Horn 23T

330134

106007 2501121C (#7)

x1
M3x12mm Hex Socket OH/TP Screw (HT)

330155 330134
x1
Steering Servo Turnbuckle (M3x30mm)

330155

106007
2501121C (#7)

16.10 mm

2501122B 2501122B 2501124B

(25T) (24T) (23T)

26
 BAG G 40
Right

330126A
x2
Steering Turnbuckle

2503270 (#3)
330777A
330126A

330777A
2501121C

20 mm

41

106002
x4
M3x10mm Hex Socket OH/TP Screw

106002

106002

27
 BAG G 42
SW-338052
S35-4 Series T7 Aluminum Settring Bellcrank
106007 Upper Part-A (with 2Hole )
108006
x1
M3x8mm FH/ST HEX Screw
108006

Position A
106007
M3x12mm Hex Socket
x1 Position B
OH/TP Screw (HT)

If servo saver arms are not included use this:

103001
x1 Position A: Standard steering response location. Use of a
M3 Nut Lock 2.5mm longer servo saver arm is required.

If servo saver arms are included use this:

Position A: Standard steering response location. Use of

the included 2.5mm longer servo saver arm is required.

103001 Position B: Quick steering response location. Standard

servo saver arm can be used.

BAG H 43 2501115

106002 When the volume

108006 210033X
x2 of fuel tank system
M3x8mm FH/ST HEX Screw
210033X is over 125cc,
using the part
210033B can be
reduced 2cc for
your fuel tank.

108006
108006 106020

106002
x3
M3x10mm Hex Socket OH/TP Screw

2502040
106002
106020
x1
M2.5x5mm Hex Socket OH/TP Screw
106002

210033X
210033X
210033X

28
 BAG H 44
108003
x2
M3x10mm FH/ST HEX Screw

108003

108003

BAG I 45 105005

105005
x4
101013 105005
M3x12mm Cap Screw
101013

101013
x4
3mm Spring Washer

330008A

330100A
330100A

29
 BAG I 46
105001
x1 115003A
M3x8mm Cap Screw

330006
101012
x1
M3x6xT0.6mm

330137
116010R
330006
101015 105001 116010R
x5
M5x8xT0.4mm
101012 330006
115003A

101015 101015
116010R
x2 115003A
Ball Bearing 5x10x4mm (Red Rubber Case)

47
105007A
x4
M4x8mm I-Head Screw

105007A

48
104011
x2
M4x4mm Set Screw (Flat Bottom)

104011

108013
x1 330140A
M4x8mm FH/ST HEX Screw
330140A

Pipe set is not

included in the kit.

108013
104011

30
 BAG J 49 210018 2503260
106007
104004

104004 106020
104004 210018
x6 330157A
M3x3mm Set Screw

2501125C 106020
330156A 104004
106007 210018
x1 2501112B
M3x12mm Hex Socket OH/TP Screw(HT)

104004 2503260
330156A
210018
x1
Throttle Rod 50mm
2501112B
210018
210018 330157A
x2
Throttle Rod 60mm 2503260

50
330157A
x2 OPTION:
Brake Adjuster Knob
104004 SW-338079-25 SWORKz Uni-Design Aluminum Throttle Servo Horn 25T
SW-338079-23 SWORKz Uni-Design Aluminum Throttle Servo Horn 23T

106020
x3
M2.5x5mm Hex Socket OH/TP Screw
330156A
210018

108006 2503260
x1
M3x8mm FH/ST HEX Screw

108006
330156A
x4
Adjuster Knob

115015
x2
Brake Spring

210018
x1
Throttle Rod Spring

51 Neutral Full Throttle Brake

Linkage
Adjustment

Idle adjustment screw

※ Turn on the transmitter and receiver. Set the throttle servo ※ Adjust the servo horn to fully open the ※ Adjust the position of servo horn to make
trim in neutral. Adjust the idle adjustment screw to make the carburettor. Change the position of the brakes function. Make sure the brakes
carburettor opening no more than 1mm. Adjust the position servo horn if the carburettor is not fully do not work when the servo trim is in
of servo horn. Check that it operates smoothly without open or opens too much. If your transmitter neutral.
making the operation of the other parts difficult. has a function to adjust throttle end points,
Make sure the brake does not work in this setting. make an adjustment this way.

31
 BAG K 52 103004
Front 338061(S)
Rear 338060(L) Front 338063A
338062A Rear 338062A
x2
S35-4 Series BBS System Teflon Coated Durable Shock Shaft (L)
400020
330562A
338063A 330563A
x2
S35-4 Series BBS System Teflon Coated Durable Shock Shaft (S) 101011

210058
103004
x4
M2.5mm Nut Lock
330557

210058 228006
x4
Shock Seal Washer 3.5X7X1.0mm

Front 400010(S)
210058 Rear 400009(L)
x8
Shock Seal Washer 3.6X7X2.5mm

101011
M2.6x6xT0.6mm
x4
53 Emulsion shock cap system assembly note

Note the direction!

338067
UP
DOWN
210058
x8 400023
Shock Seal O-Ring

400020
x4
Shock Seal O-Ring 35
mm
108029
45.25
mm

400019 2501121C
x4
Shock Spring Adjust
Nut O-Ring

108029
M2.0x4.6mm FH/ST Slowly push the shock shaft
x4 to the end of shock cap.
HEX Screw (1.5mm HexHead) Then tight screw M2x4mm

54
228006 330560B

115191 330134
x2
S35 Series Competition Black Line Rear
Shock Spring (RM3-Dot)(80X1.6X10.0)

400019

115183
x2 Front SWC-115183
S35-4 Black Competition Front
Shock Spring (US3-Dot)(62X1.6X7.75)
Rear SWC-115191

32
 BAG K 52 103004
Front 338061(S)
Rear 338060(L) Front 338063(S)
338062A Rear 338062(L)
x2
S35-4 Series BBS System Teflon Coated Durable Shock Shaft (L)
400020
330562A
338063A 330563A
x2
S35-4 Series BBS System Teflon Coated Durable Shock Shaft (S) 101011

210058
103004
x4
M2.5mm Nut Lock
330557

210058 228006
x4
Shock Seal Washer 3.5X7X1.0mm

Front 400010(S)
210058 Rear 400009(L)
x8
Shock Seal Washer 3.6X7X2.5mm

Standard bladder shock cap assembly note

101011
x4
M2.6x6xT0.6mm
338067
108029
400022A-S
210058
x8
Shock Seal O-Ring

400020
x4
Shock Seal O-Ring 35
mm
45.25
mm
2501121C

400019
x4
Shock Spring Adjust
Nut O-Ring

108029
M2.0x4.6mm FH/ST Slowly push the shock shaft
x4 to the end of shock cap.
HEX Screw (1.5mm HexHead) Then tight screw M2x4mm

54
228006 330560B

115191 330134
x2
S35 Series Competition Black Line Rear
Shock Spring (RM3-Dot)(80X1.6X10.0)

400019

115183
x2 Front SWC-115183
S35-4 Black Competition Front
Shock Spring (US3-Dot)(62X1.6X7.75)
Rear SWC-115191

33
 BAG J 55 330138B
338068

101010A
105006A
M3x28mm Cap Screw
x2 105006A

101010A
105013A
M3x25mm Cap Screw
x2 101010A

105006A
105013A

56
103003A
103003A
x1
Flange M3 Nut Lock

103003A
330243
(Anti-Clockwise)

330243
x2
SWORKz 3x16mm Shock Hex Screw Clockwise
330243

330243
x2
SWORKz 3x16mm Shock Hex Screw Anti-Clockwise

103003A

103003A
330243
(Anti-Clockwise)

330243

34
 BAG L 57
Using air filter oil
108006 (Not included) 610004
x1
M3x8mm FH/ST HEX Screw

106002 540003
x1 610004
M3x10mm Hex Socket OH/TP Screw 2501126A

103003A 108006
x1
Flange M3 Nut Lock

540003

2501126A

103003
106002

58

410038

35
 BAG N 59 106025
228008BK 105025

106025 228008BK
228008BK
106025
105005
x2
M3x12mm Cap Screw

39mm

PRO TIP:
106025 Attention!
x5
M2.5x8mm Hex Socket OH/TP Screw Please do not follow the
wing hole markings to
228008BK drill. Please drill both
holes 0.5mm inwards.

60
330122A
x4
Wheel Nut

Tires and wheels

are Not included

330122A

330122A

61

258001C-N

Use body scissors to

cut a hole to fit your
exhaust pipe.

36
 62 Use water/washing
solution to clean
body.

Apply window masks

as shown.

518003

Paint body.

63
115019

106010
x1
Button Head Screw M3x6mm

106010

115019

37
 Race time / Lap:
SET-UP SHEET Best lap:

Diff. Oil Track Conditions

Name: Elliott Boots Size: Open Med. Tight
Front: #15000 ✔

Date: 09/05/2021 Center: #10000 Traction: ✔

High Med. Low
Track: Genzone Rear: #5000 Surface: Smooth ✔ Med. Bumpy
Tire Engine Clutch
Front Rear Type: 721 REDS Muffler: EFRA 2143 Clutch shoes: ALU x 4
Type: 3308XR-T2 Type: 3308XR-T2 Gasket: mm Fuel: SHOOT FUEL Spring: 1.0 x 4pc mm
Foam: TPRO BLUE Foam: TPRO BLUE Plug: REDS TS-3 Clutch bell / Spur gear: 13/46T

Front Suspension ✔ Bladder Emulsion

1 Front Toe-In
F2 Cap: Soft material
2 mm F Medium material
3 ✔
Spacer: mm
4
5 Al(6g)
Oil: #750
C-C 107
R
R2 mm mm Pistons: 1.2x8H
1 ✔
2 Spring: 9.0
Front Roll Center

Track width mm

Camber angle Upper 0 mm

Wheel Hub Note:
Camber Angle Lower 2 mm
STD
L: 1 ° Toe angle 2 °
R: 1 ° ✔ Use 2.6
Sway bar mm
Rebound stop 106 mm None
Steening Ackerman 2
Rear Suspension 1 mm Notes:
Rear Toe-In
F
✔
2 Front Ride Height
S35-4 Series Shock
3 Chassis Conversion Kit
R
4 22 mm
(Elliott Boots Edition)
Ground
✔ Bladder Emulsion
Body: SWORKz VISION
1 ✔ 3 Cap: Soft material
Wing: T-Works Medium material
2 4
5 Spacer: mm
Wing Position
✔ H Oil: #650
M
1 L C-C129
2 ✔ H
Wing Angle: Pistons: 1.3x8H
Camber 3 mm
angle M 0 °
4 L Spring: 86X1.6X10.5
✔ 5
6 Upper arm position
7 6 1
8 7 2 Sway bar Use 2.8✔ mm
Wheel Hub Note: 8 3 None
STD 9 ✔
4 Camber angle -1 °
1 2 ✔ 10 5
Rear Ride Height
Rebound stop 128 mm Chassis
0 mm
28 mm Notes:
Ground Long
Wheelbase F 2 mm A ✔ Brass(15g) x 1 Shock
adjustment R 3 mm Conversion
F R B ✔ Brass(15g) x 1
✔ ✔ C Brass(15g) x Kit
Front

Option Parts List

Front Lower Arm Rear Lower Arm
Front Upper Arm ✔ Hard Medium ✔ Soft Hard Medium ✔ Soft
Hard ✔ Soft

Carbon Cover Carbon Cover Carbon Cover

1 .0 mm 1 .0 mm 1 .0 mm

38
 Race time / Lap:
SET-UP SHEET Best lap:

Diff. Oil Track Conditions

Name: Size: Open Med. Tight
Front:
Date: Center: Traction: High Med. Low
Track: Rear: Surface: Smooth Med. Bumpy
Tire Engine Clutch
Front Rear Type: Muffler: Clutch shoes:
Type: Type: Gasket: mm Fuel: Spring: mm
Foam: Foam: Plug: Clutch bell / Spur gear:
Front Suspension Bladder Emulsion
1 Front Toe-In
Cap: Soft material
2 F mm F Medium material
3 Spacer: mm
4
5 Al(6g)
Oil:
R
R mm mm Pistons:
1 2 Spring:
Front Roll Center

Track width mm

Camber angle Upper mm

Wheel Hub Note:
Camber Angle Lower mm
L: ° Toe angle °
R: °
Sway bar Use mm
Rebound stop mm None
Steening Ackerman
Rear Suspension 1 mm Notes:
Rear Toe-In
F 2 Front Ride Height
3 Chassis

R
4 mm
Ground

Bladder Emulsion
Body:
1 3 Cap: Soft material
Wing: Medium material
2 4
5 Spacer: mm
Wing Position
H Oil:
M
1 L
2 H
Wing Angle: Pistons:
Camber 3 mm
angle M °
4 L Spring:
5
6 Upper arm position
7 6 1
8 7 2 Sway bar Use mm
Wheel Hub Note: 8 3 None
9 4 Camber angle °
1 2 10 5
Rear Ride Height
Rebound stop mm Chassis mm
mm Notes:
Ground

Wheelbase F mm A Brass(15g) x
adjustment R mm
F R B Brass(15g) x
C Brass(15g) x
Front

Option Parts List

Front Lower Arm Rear Lower Arm
Front Upper Arm Hard Medium Soft Hard Medium Soft
Hard Soft

Carbon Cover Carbon Cover Carbon Cover

mm mm mm

39
 Pa r ts No. L i s t
Part No. Part Name Q`ty in Use ltem No. Part No. Part Name Q`ty in Use ltem No.
210091 S35-3W Plastic Front/Rear Big Bore Diff Case 2 SW-210091 330560B S35 New BBS System Shock Spring Adjust Nut (BK) 4 SW-330560B
210079A S35-4 Plastic Center Big Bore HET Diff Case 1 SW-210079A 330562A S350 New BBS System Shock Piston 1.3mmX6 Holes (BK) 2 SW-330562A
210033X S35/350 Series Tubed Floating Fuel Filter System Tank Set 1 SW-210033X 330563A S350 New BBS System Shock Piston 1.4mmX6 Holes (BK) 2 SW-330563A
2501115 S350 Rear Lower Arm Dusty Cover with Fuel Sprinkle Guard 1 SW-2501115 330580 S350 Competition Series Professional Brake Disc 2 SWC-330580
2501124 S350 Center Diff. Mount Set 2 SW-2501124 330647 S350 BBD Special Brake Cam 1 SWC-330647
2501529 S350 BX1/BR1Rear Chassis Brace 1 SW-2501529 330661A S35-T/S35 Series Competition Center Drive Join (5mm set screw) 2 SW-330661A
2501097B S35 Series Front Bumper 1 SW-2501097B 330663A S35-3 Series Steel R-Center Drive Shaft (115mm) 1 SW-330663A
2501121C S35/S350 Series Ball End Set with Shock Plastic Parts 2 SW-2501121C 330767A S35-3 Series Steel F-Center Dive Shaft (88mm) 1 SW-330767
2501122B S35/S350 Series Settring Bellcrank Set 2.0 Set (with Servo Horn) 1 SW-2501122B 330777A S35-4 Series Steering Linkage Ball Stud 7mm(L7) 4 SW-330777A
2501126A S350/S350T Series Option Air Filter Extension Set 1 SW-2501126A 330782 S35-3 Series Rear Hub Carriers Hinge Pin 2 SW-330782
2502040-02 S350T Body Mount with Fuel Tank Ring-pull 1 SW-2502040-02 338011 S35 series Pinion Gear Stopper (5x7x5.1mm) 2 SW-338011
2503260 S353 Series Plastic Inserts Set 1 SW-2503260 338014 S35-3W T-7075AL Rear Lower Fully Adjustable Toe-In Block (3 degree) 1 SW-338014
2503261A S35-3/GT Series Gear Box Set (Fit 5x13x4mm Ball Bearing) 2 SW-2503261A 338023 S35-3W Pinion Gear 13T 2 SW-338023
2503262 S35-3 Nitro Buggy Radio Tray Set 1 SW-2503262 338024 S35-3W Crown Gear 43T 2 SW-338024
2503264A S35-3 Series Front Steering Knuckle (Type 2.0) L 1 SW-2503264A 338025 S35-3W Bevel Gear Shaft 6 SW-338025
2503270-1 S35-3 Series Front Upper Arms 2 SW-2503270-1 338027 S35-3W Front/Rear Diff. Outdrive 4 SW-338027
2503270-2 S35-3 Series Rear Upper Arm Outside Ball Ends 4 SW-2503270-2 338028 S35-3W Center Diff. Outdrive 2 SW-338028
2503270-3 S35-3 Series Front Steering Ball Ends 2 SW-2503270-3 338040 S35-4 Series Center Spur Gear for Big Diff. Bevel Gear Case (47T) 1 SW-338040
228001 S35-4 Series Plastic Inserts Set 2 SW-228001 338043 S35-3/4 Series Servo Saver Nut with Screw Fixed 1 SW-338043
228002-1 S35-4 Series Plastic Rear Wheel Hub (R=L) 2 SW-228002-1 338047A S35-4 Nitro Series T7075 Aluminum Lightened Main Chassis 1 SW-338047A
228002-2 S35 Series Plastic Front Chassis Shorty Brace 1 SW-228002-2 338048 S35-4 Series Servo Saver Shaft 2 SW-338048
228003A S35 Series Integrated Wing Mount Set 2.0 1 SW-228003A 338049 S35-4 Series T7 Aluminum Rear Front Lower Suspension Plate (RF) 1 SW-338049
228004 S35-4 Series Plastic Side Guard Set 1 SW-228004 338050 S35-4 Series T7 Aluminum Rear Shock Tower 1 SW-338050
228005S-F S35-4 Series Front Lower Arm in Soft Material 2 SW-228005S-F 338051 S35-4 Series T7 Aluminum Steering Knuckle Plate (R=L) 2 SW-338051
228005S-R S35-4 Series Rear Lower Arm in Soft Material 2 SW-228005S-R 338052 S35-4 Series T7 Aluminum Settring Bellcrank Upper Part-A (with 2Hole) 1 SW-338052
228006 S35 Series Shock End/Body Mount/Ball Ends Set 2 SW-228006 338053 S35-4 Series T7 Aluminum Steering Plate 1 SW-338053
228008BK SWORKz 1/8 Off Road Formula 2.0 Race Wing (BK) 1 SW-228008BK 338054 S35-4 Series T7 Aluminum Front Shock Tower 1 SW-338054
210058 S350 New BBS System Shock Seal Washer 3.6X7X2.5mm 8 SW-210058 338056 S35-4 Series Lower Arm Hinge Pin (68.5mm) 4 SW-338056
210058 S350 New BBS System Shock Seal Washer 3.5X7X1.0mm 4 SW-210058 338057 S35-4 Series T7 Aluminum Front Upper Arm Holder 1 SW-338057
210046 S350 Series LDS Universal Cross Drive Shaft Set 92.5mm (1pc) 4 SW-210046 338058 S35-4 Series T7 Aluminum Front Lower Arm Plate (FF) 1 SW-338058
210043 S350 Professional Matel Brake Calipers 2.0 A Side 2 SW-210043 338059 S35-4 Series T7 Aluminum Front Lower Arm Holder (FR) 1 SW-338059
210043 S350 Professional Matel Brake Calipers 2.0 B Side 2 SW-210043 338060 S35-4 Series BBS System Shock Body (L) 2 SW-338060
210018 Brake Spring 2 SW-210018 338061 S35-4 Series BBS System Shock Body (S) 2 SW-338061
210018 Throttle Rod 50mm 1 SW-210018 SW-338062A S35-4 Series BBS System Teflon Coated Durable Shock Shaft (L) 2 SW-338062A
210018 Throttle Rod Spring 1 SW-210018 SW-338063A S35-4 Series BBS System Teflon Coated Durable Shock Shaft (S) 2 SW-338063A
210018 Brake Rod 60mm 2 SW-210018 338067 S35-4 Series Emulsion/Bladder 2 Ways System Shock Cap 4 SW-338067
200193 Antenna Tube 1 SW-200193 338068 S35-4 Series T7 Aluminum Shock Stud (L) 2 SW-338068
258001CN S35 Series Falcon ST-4 Clean Body Shell (Pre-Cut for Nitro Buggy) 1 SW-258001CN SW-338070B S35 Series Rear Upper Sus. Arm Ball Stud (7.0mm Hex) 2 SW-338070B
320010 S35-3W Diff. Bevel Gear 10T 12 SW-328001 340003 S35-3 Series Pro-composite Carbon Front Upper Arm Cover Set (1mm) 2 SW-340003
320009 S35-3W Diff. Bevel Gear 20T 6 SW-328001 340016 S35-4 Series Pro-composite Carbon Rear Wheel Hub Adjust Plate (R=L) 4 SW-340016
330006 Tornado Clutch Shoes 3 SW-330006 340017 S35-4 Series Pro-composite Carbon Steering Bellcrank Plate 1 SW-340017
330008A SWORKz Tornado Fly Wheel Set (GM) 1 SW-330008A 420026 S350/S350T Series Option Air Filter Extension Adapter 1 SW-420026
330008A Tornado Fly Wheel Center Nut 1 SW-330008A 420011 Fuel Tube 2 SW-420011
330008A Fly Wheel Collect 1 SW-330008A 420010 Antenna Cup 1 SW-420010
330015 Pin M2.2x9.9mm 6 SW-330015 410038 Super Silicone Tube 2455x30mm (Transparent) 1 SW-410038
330090 S350 Series Carbon Fiber Center Diff. Plate 1 SW-330090 400023 S35 Series BBS System Seal O-Ring for Emulsion Shock Cap 4 SW-400023
330100A S350 Engine Mount (L) (HC) 1 SW-330100A 400022A-S S35 Series BBS System Pro Shock Bladder (Soft) 4 SW-40022A-S
330100A S350 Engine Mount (R) (HC) 1 SW-330100A 400020 S350 New BBS System Shock Seal O-Ring 4 SW-400020
330104 Brake Cam (S) 1 SW-330104 400019 S350 New BBS System Shock Spring Adjust Nut O-Ring 4 SW-400019
330104 Brake Cam (L) 1 SW-330104 400010 Shock Boot (S) 2 SW-400010
330104 Brake Cam 1 SW-330104 400009 Shock Boot (L) 2 SW-400009
330114A S350 Sseries Servo Saver Post (HC) 1 SW-330114A 400006 Shock Seal O-Ring 8 SW-210058
330117A S350 Series Knuckle Pivot Ball Washer(GM) 2 SW-330117A 400005 Shock Spring Adjust Nut O-Ring 4 SW-400005
330118A S350 Series Knuckle Pivot Ball Nut(GM) 4 SW-330118A 400002 O-ring S5 4.8X1.5 6 SW-400002
330119 Front Upper Arm Hinge Pin 2 SW-330119 540003 CABLE STRAPS FOR AIRFILTER 2 SW-540003
330121B S350 Wheel Hub(L4.5mm)(HC) 4 SW-330121B 518003 S35 Series Falcon ST-4 Clean Body Shell Window Mask 1 SW-258001CN
330122A S350 Wheel Nut (HC) 4 SW-330122A 518001 S35-4 Body Decal Sheet 1 SW-258001CN
330123A S350 EVO Rear Upper Sus. Arm Turnbuckles M5x38mm 2 SW-330123A 510080A SWORKz 1/8 Off Road Formula Race Wing Decal 1 SW-228008BK
330124 Pin M3.0x16.8mm 4 SW-330124 510091 SWORKz Origional Logo Sticker 1 SW-510091
330125 Rear Upper Sus. Arm Ball Stud 4 SW-330125 610023 S35-3W Diff. Gasket (0.4T) 2 SW-610023
330126A S350 EVO Steering Turnbuckle M4x40mm 2 SW-330126A 610020 S35-3 Series Center Big Bore Plastic Diff. Case Gasket 1 SW-610020
330134 Shock Ball Stud 12 SW-330134 610019 S35-3 Series Servo Saver Spring Dusty Protect Sponge 1 SW-610019
330136 Sway Bar Ball Stud 4 SW-330136 610004 Air Filter Outer Foam 1 SW-610004
330137 Clutch Bell 13T 1 SW-330137 610004 Air Filter Foam 1 SW-610004
330138B S350 EVO Aluminum Shock Cap Stud (-1.3mm) 4 SW-330138B 115003A SWORKz Tornado Clutch Spring II (1.0mm) 3 SW-115003A
330140A Pipe Holder(GM) 1 SW-330140A 115004A Servo Saver Spring 1 SW-115004A
330140A Pipe Spring 1 SW-330140A 115005 Rear Sway Bar 2.8mm 1 SW-115005
330155 Steering Servo Turnbuckle (M3x30mm) 2 SW-330155 115006 Rear Sway Bar 2.6mm 1 SW-115006
330156A Adjuster Knob(GM) 4 SW-330156A 115008A Front Sway Bar 2.3mm 1 SW-115008A
330157A Brake Adjuster Knob(GM) 2 SW-330157A 115011A S35-GT Series Pipe Spring (L) 1 SW-115011A
330243 SWORKz 3x16mm Shock Hex Screw Clockwise 2 SW-330243 115019 Body Clip 2 SW-115019
330244 SWORKz 3x16mm Shock Hex Screw Anti-Clockwise 2 SW-330243 115035A Front Sway Bar 2.2mm 1 SW-115035A
330252 S350 BX1/BR1 Steering Knuckle Pivot Ball Turnbuckle 4 SW-330252 115098 Brake Pad Spring 4 SW-115098
330399B S35-3 Series Aluminum Rear Chassis Brace Mount (GM) 1 SW-330399B 115164 S35 Series Competition Black Line Front Shock Spring (3 Dot)(75X1.6X9.0) 2 SWC-115164
330557 S350 New BBS System Shock Seal Cap (GM) 4 SW-330557 115191 S35 Series Competition Black Line Rear Shock Spring (RM3-Dot)(80X1.6X10.0) 2 SWC-115191

40
 Pa
Parrts
ts No.
No. Lis
L istt Spare Par t List
Part No. Part Name Q`ty in Use ltem No. Item No. Part Name
SW-228001 S35-4 Series Plastic Inserts Set (2Set)
116004R Ball Bearing 6x10x3mm (Red Rubber Case) 4 SW-116004R SW-228002-1 S35-4 Series Plastic Rear Wheel Hub (R=L)(2PC)
116006R Ball Bearing 8x16x5mm (Red Rubber Case) 14 SW-116006R SW-228002-2 S35 Series Plastic Front Chassis Shorty Brace (1PC)
116009 Ball Bearing M5x8x2.5 ZZ (4PC) 2 SW-116009 SW-228003A S35 Series Integrated Wing Mount Set 2.0
116010R Ball Bearing 5x10x4mm (Red Rubber Case) 2 SW-116010R SW-228004 S35-4 Series Plastic Side Guard Set
116019R Ball Bearing 5x13x4mm (Red Rubber Case) 4 SW-116019R SW-228005S-F S35-4 Series Front Lower Arm in Soft Material (1PC)
117003 Flange Ball Bearing 3x6x2.5mm 4 SW-117003 SW-228005S-R S35-4 Series Rear Lower Arm in Soft Material (1PC)
101004 Washer 3.5X10X0.2mm 12 SW-101004 SW-228006 S35 Series Shock End/Body Mount/Ball Ends Set (2Set)
101010A M3 Countersunk Washer(GM) 4 SW-101010A SW-228008BK SWORKz 1/8 Off Road Formula 2.0 Race Wing (BK)
101011 M2.6x6xT0.6mm 4 SW-101011 SW-2501097B S35 Series Front Bumper (2PC)
101013 3mm Spring Washer 4 SW-101013 SW-2501115 S350 Rear Lower Arm Dusty Cover with Fuel Sprinkle Guard
101015 M5x8xT0.4mm 4 SW-101015 SW-2501121C S35/S350 Series Ball End Set with Shock Plastic Parts
101016 M5x8xT0.8mm 1 SW-101016 SW-2501122B S35/S350 Series Settring Bellcrank Set 2.0 Set (with Servo Horn)
101018 SHIM 13x16x0.2mm 12 SW-101018 SW-2501124 S350 Center Diff. Mount Set (2 Set)
101019 SHIM 6.0x10.0x0.2mm 1 SW-101019 SW-2501126A S350/S350T Series Option Air Filter Extension Set
101020A S350 Sries 3mm Countersunk Washers (GM) 2 SW-101020A SW-2501529 S350 BX1/BR1Rear Chassis Brace
101021 M3x8xT0.8mm 3 SW-101021 SW-2502040-02 S350T Body Mount with Fuel Tank Ring-pull
101039 Steel Washer 5x12x0.3mm 6 SW-101039 SW-2503260 S353 Series Plastic Inserts Set
103001 M3 Nut Lock 25 SW-103001 SW-2503261A S35-3/GT Series Gear Box Set (Fit 5x13x4mm Ball Bearing)
103003A Flange M3 Nut Lock (GM) 5 SW-103003A SW-2503262 S35-3 Nitro Buggy Radio Tray Set
103004 M2.5mm Nut Lock 4 SW-103004 SW-2503264A S35-3 Series Front Steering Knuckle (Type 2.0)
104004 M3x3mm Set Screw 13 SW-104004 SW-2503270-01 S35-3 Series Front Upper Arms (2pc)
104005 M3x4mm Set Screw 4 SW-104005 SW-2503270-02 S35-3 Series Rear Upper Arm Outside Ball Ends (2pc)
104010 M5x4mm Set Screw (Flat Bottom) 6 SW-104010 SW-2503270-03 S35-3 Series Front Steering Ball Ends (4pc)
104011 M4x4mm Set Screw (Flat Bottom) 1 SW-104011 SW-200193 Antenna Tube
105001 M3x8mm Cap Screw 1 SW-105001 SW-210018 Throttl Linkage Set
105005 M3x12mm Cap Screw 6 SW-105005 SW-210033X S35/350 Series Tubed Floating Fuel Filter System Tank Set
105018 M2x6mm Cap Head Screw 1 SW-105018 SW-210043 S350 Professional Matel Brake Calipers 2.0 Set
105013A M3x25mm Cap Screw 4 SW-105013A SW-210046 S350 Series LDS Universal Cross Drive Shaft Set 92.5mm (1pc)
105007A M4x8mm I-Head Screw Thin 4 SW-105007A SW-210058 S350 series BBS Shock Seal Kit
105006A M3x28mm Cap Screw full thread 2 SW-105006A SW-210079A S35-4 Plastic Center Big Bore HET Diff Case
106001 M3x8mm Hex Socket OH/TP Screw 3 SW-106001 SW-210091 S35-3W Plastic Front/Rear Big Bore Diff Case
106002 M3x10mm Hex Socket OH/TP Screw 14 SW-106002 SW-258001C-N S35 Series Falcon ST-4 Clean Body Shell (Pre-Cut for Nitro Buggy)
106003 M3x16mm Hex Socket OH/TP Screw 8 SW-106003 SW-328001 S35-3/4 Series HET Diff. Bevel Gear Set
106006 M3x20mm Hex Socket OH/TP Screw 5 SW-106006 SW-330006 Tornado Clutch Shoes
106007 M3x12mm Hex Socket OH/TP Screw(HT) 9 SW-106007 SW-330008A SWORKz Tornado Fly Wheel Set (GM)
106008 M3x12mm Hex Socket OH/TP Screw 6 SW-106008 SW-330015 Pin M2.2x9.9mm
106009 M3x25mm Hex Socket OH/TP Screw 10 SW-106009 SW-330090 S350 Series Carbon Fiber Center Diff. Plate
106013 M2.5x8mm 1.5mmHex Socket OH/ST Screw 6 SW-106013 SW-330100A S350 Sseries Engine Mount Set (HC)
106015 M3x5mm Hex Socket OH/TP Screw 2 SW-106015 SW-330104 Brake Cam Set
106020 M2.5x5mm 1.5mmHex Socket OH/ST Screw 14 SW-106020 SW-330114A S350 Sseries Servo Saver Post (HC)
106025 M2.5x8mm Hex Socket OH/TP Screw 5 SW-106025 SW-330117A S350 Series Knuckle Pivot Ball Washer(GM)
106021A S35 Series M4x10mm Hex Socket OH/TP Set Screw 4 SW-106021A SW-330118A S350 Series Knuckle Pivot Ball Nut(GM)
108001 M3x12mm FH/ST HEX Screw 20 SW-108001 SW-330119 Front Upper Arm Hinge Pin
108003 M3x10mm FH/ST HEX Screw 23 SW-108003 SW-330121B S350 Wheel Hub(L4.5mm)(HC)
108005 M3x14mm FH/ST HEX Screw 2 SW-108005 SW-330122A S350 Wheel Nut (HC)
108006 M3x8mm FH/ST HEX Screw 23 SW-108006 SW-330123A S350 EVO Rear Upper Sus. Arm Turnbuckles M5x38mm
108007 M3x6mm FH/ST HEX Screw 12 SW-108007 SW-330124 Pin M3.0x16.8mm
108008 M3x35mm FH/ST HEX Screw 4 SW-108008 SW-330125 Rear Upper Sus. Arm Ball Stud
108010 M4x10mm FH/ST HEX Screw 6 SW-108010 SW-330126A S350 EVO Steering Turnbuckle M4x40mm
108012 M4x16mm FH/ST HEX Screw 8 SW-108012 SW-330134 Shock Ball Stud 6mmxL6.7
108013 M4x8mm FH/ST HEX Screw 1 SW-108013 SW-330136 Sway Bar Ball Stud
108019 M2.6x6mm FH/ST HEX Screw 2 SW-108019 SW-330137 Clutch Bell 13T
108029 M2.0x4.6mm FH/ST HEX Screw (1.5mm HexHead) 4 SW-108029 SW-330138B S350 Series Aluminum Shock Cap Stud (-1.3mm)(2PC)
SW-330140A S350 SeriesPipe Holder(GM)
SW-330155 Steering Servo Turnbuckle (M3x30mm)
SW-330156A S350 Series Adjuster Knob (Included Brake Adjuster Knob)(GM)
SW-330157A Brake Adjuster Knob(GM)
SW-330243 SWORKz 3x18mm Shock Hex Screw Set (Anti-Clockwise)
SW-330252 S350 BX1/BR1 Steering Knuckle Pivot Ball Turnbuckle
SW-330399B S35-3 Series Aluminum Rear Chassis Brace Mount (GM)
SW-330557 S350 New BBS System Shock Seal Cap (GM)
SW-330560B S35 New BBS System Shock Spring Adjust Nut (BK)
SW-330562A S35 Series BBS System Shock Piston 1.3mmX6 Holes (BK)(2PC)
SW-330563A S35 Series BBS System Shock Piston 1.4mmX6 Holes (BK)(2PC)
SW-330661A S35-T/S35 Series Competition Center Drive Join (5mm set screw)
SW-330663A S35-3 Series Steel R-Center Drive Shaft (115mm)
SW-330767A S35-3 Series Steel F-Center Dive Shaft (88mm)
SW-330777A S35-4 Series Steering Linkage Ball Stud 7mm(L7)(4PC)
SW-330782 S35-3 Series Rear Hub Carriers Hinge Pin
SW-338011 S35-3 series Pinion Gear Stopper (5x7x5.1mm)(4PC)
SW-338014 S35-3W T-7075AL Rear Lower Fully Adjustable Toe-In Block (3 degree)
SW-338023 S35-3W Pinion Gear 13T
SW-338024 S35-3W Crown Gear 43T
SW-338025 S35-4 HET Bevel Gear Shaft (2pc)

41
 Spare Pa r t L is t
Item No. Part Name Item No. Part Name
SW-338027 S35-4 Front/Rear HET Diff. Outdrive (2pc) SW-106009 M3x25mm Hex Socket OH/TP Screw
SW-338028 S35-4 Center HET Diff. Outdrive (2pc) SW-106013 M2.5x8mm 1.5mmHex Socket OH/ST Screw
SW-338040 S35-4 Series Center Spur Gear for Big Diff. Bevel Gear Case (47T) SW-106015 M3x5mm Hex Socket OH/TP Screw
SW-338043 S35-3/4 Series Servo Saver Nut with Screw Fixed SW-106020 M2.5x5mm 1.5mmHex Socket OH/ST Screw
SW-338047A S35-4 Nitro Series T7 Aluminum Lightened Main Chassis 2.0 SW-106021A S35 Series M4x10mm Hex Socket OH/TP Set Screw
SW-338048 S35-4 Series Servo Saver Shaft(2PC) SW-108001 M3x12mm FH/ST HEX Screw
SW-338049 S35-4 Series T7 Aluminum Rear Front Lower Suspension Plate (RF) SW-108003 M3x10mm FH/ST HEX Screw
SW-338050 S35-4 Series T7 Aluminum Rear Shock Tower SW-108005 M3x14mm FH/ST HEX Screw
SW-338051 S35-4 Series T7 Aluminum Steering Knuckle Plate (R=L) SW-108006 M3x8mm FH/ST HEX Screw
SW-338052 S35-4 Series T7 Aluminum Settring Bellcrank Upper Part-A (with 2Hole) SW-108007 M3x6mm FH/ST HEX Screw
SW-338053 S35-4 Series T7 Aluminum Steering Plate SW-108008 M3x35mm FH/ST HEX Screw
SW-338054 S35-4 Series T7 Aluminum Front Shock Tower SW-108010 M4x10mm FH/ST HEX Screw
SW-338056 S35-4 Series Lower Arm Hinge Pin (68.5mm)(2pc) SW-108012 M4x16mm FH/ST HEX Screw
SW-338057 S35-4 Series T7 Aluminum Front Upper Arm Holder SW-108013 M4x8mm FH/ST HEX Screw
SW-338058 S35-4 Series T7 Aluminum Front Lower Arm Plate (FF) SW-108019 M2.6x6mm FH/ST HEX Screw
SW-338059 S35-4 Series T7 Aluminum Front Lower Arm Holder (FR) SW-108029 M2.0x4.6mm FH/ST HEX Screw (1.5mm HexHead)
SW-338060 S35-4 Series BBS System Shock Body (L)(2PC) SW-115003A SWORKz Tornado Clutch Spring II (1.0mm)
SW-338061 S35-4 Series BBS System Shock Body (S)(2PC) SW-115004A Servo Saver Spring
SW-338062A S35-4 Series BBS System Teflon Coated Durable Shock Shaft (L) SW-115005 Rear Sway Bar 2.8mm
SW-338063A S35-4 Series BBS System Teflon Coated Durable Shock Shaft (S) SW-115006 Rear Sway Bar 2.6mm
SW-338067 S35-4 Series Emulsion/Bladder 2 Ways Syatem Shock Cap (2PC) SW-115008A Front Sway Bar 2.3mm
SW-338068 S35-4 Series T7 Aluminum Shock Stud (L)(2PC) SW-115011A S35-GT Series Pipe Spring (+10mm Longer)
SW-338070B S35 Series Rear Upper Sus. Arm Ball Stud (7.0mm Hex) SW-115019 Body Clip
SW-340003 S35-3 Series Pro-composite Carbon Front Upper Arm Cover Set (1mm) SW-115035A S35/350 Series Front Sway Bar 2.2mm
SW-340016 S35-4 Series Pro-composite Carbon Rear Wheel Hub Adjust Plate (R=L)(2PC) SW-115098 Brake Pad Spring
SW-340017 S35-4 Series Pro-composite Carbon Steering Bellcrank Plate SWC-115164 S35 Series Black Competition Front Shock Spring (M3-Dot)(75X1.6X9.0)
SWC-330580 S350 Competition Series Professional Brake Disc SWC-115191 S35 Series Competition Black Line Rear Shock Spring (RM3-Dot)(80X1.6X10.0)
SWC-330647 S350 BBD Special Brake Cam SW-116004R Ball Bearing 6x10x3mm (Red Rubber Case)(4PC)
SW-400002 O-ring S5 4.8X1.5 SW-116006R Ball Bearing 8x16x5mm (Red Rubber Case)(10PC)
SW-400005 Shock Spring Adjust Nut O-Ring SW-116009 Ball Bearing M5x8x2.5 ZZ (4PC)
SW-400009 Shock Boot (L) SW-116010R Ball Bearing 5x10x4mm (Red Rubber Case)(4PC)
SW-400010 Shock Boot (S) SW-116019R Ball Bearing 5x13x4mm (Red Rubber Case)(4PC)
SW-400019 S350 New BBS System Shock Spring Adjust Nut O-Ring (4pc) SW-117003 Flange Ball Bearing 3x6x2.5mm(2pc)
SW-400020 S350 New BBS System Shock Seal O-Ring (4pc)
SW-400023 S35-4 Series BBS System Seal O-Ring for Emulsion Shock Cap (4PC)
SW-40022 S350 New BBS System Shock Bladder (Medium)
SW-410038 Super Silicone Tube 2455x30mm (Transparent)
SW-420010 Antenna Cup
SW-420026 S350/S350T Series Option Air Filter Extension Adapter
SW-510091 SWORKz Origional Logo Sticker (2PC)
SW-540003 SWORKz Cable Straps for 1/8 Buggy Airfilter (10PC)
SW-610004 Air Filter Foam Set
SW-610019 S35-3 Series Servo Saver Spring Dusty Protect Sponge (2pc)
SW-610020 S35-3 Series Center Big Bore Plastic Diff. Case Gasket (3pc)
SW-610023 S35-4 HET Diff. Gasket (0.4T)(4pc)
SW-101004 Washer 3.5X10X0.2mm
SW-101010A M3 Countersunk Washer(GM)
SW-101011 M2.6x6xT0.6mm
SW-101013 3mm Spring Washer
SW-101015 M5x8xT0.4mm
SW-101016 M5x8xT0.8mm
SW-101018 SHIM 13x16x0.2mm
SW-101019 SHIM 6.0x10.0x0.2mm
SW-101020A S350 Sries 3mm Countersunk Washers (GM)
SW-101021 M3x8xT0.8mm
SW-101039 SWORKz HET Diff Steel Washer 5x12x0.3mm(10PC)
SW-103001 M3 Nut Lock
SW-103003A Flange M3 Nut Lock (GM)
SW-103004 M2.5mm Nut Lock
SW-104004 M3x3mm Set Screw
SW-104005 M3x4mm Set Screw
SW-104010 M5x4mm Set Screw (Flat Bottom)
SW-104011 M4x4mm Set Screw (Flat Bottom)
SW-105001 M3x8mm Cap Screw
SW-105005 M3x12mm Cap Screw
SW-105006A M3x28mm Cap Screw full thread
SW-105007A M4x8mm I-Head Screw Thin
SW-105013A M3x25mm Cap Screw
SW-105018 M2x6mm Cap Head Screw
SW-106001 M3x8mm Hex Socket OH/TP Screw
SW-106002 M3x10mm Hex Socket OH/TP Screw
SW-106003 M3x16mm Hex Socket OH/TP Screw
SW-106006 M3x20mm Hex Socket OH/TP Screw
SW-106007 M3x12mm Hex Socket OH/TP Screw (HT)
SW-106008 M3x12mm Hex Socket OH/TP Screw

42
 Op ti on P a r t L is t
Item No. Part Name Item No. Part Name
SW-115026A SWORKz Tornado Clutch Spring II (1.1mm)(GR) SWC-116019A SWORKz Competition 5x13x4mm Ball Bearing (Metal Case) (4PC)
SW-115027A SWORKz Tornado Clutch Spring II (1.2mm)(GD) SWC-116019B SWORKz Competition 5x13x4mm Ball Bearing (Metal Case/Japan) (4PC)
SW-115077A SWORKz Tornado Clutch Spring II (0.9mm)(BK) SW-115007 S35/S350 Series Rear Sway Bar 3.0mm
SW-116006A High Performance Rubber Cover Ball Bearing 8x16x5mm (10pc) SW-218001 S35/350 Series Font Sway Bar Set (2.0/2.1/2.2/2.3/2.4/.2.5/2.6/2.8mm)
SW-116010B High Performance Ball Bearing 5x10x4mm(coffee)(4pc) SW-218002 S35/350 Series Rear Sway Bar Set (2.4/2.5/2.6/2.7/2.8/3.0mm)
SW-116019C SWORKz High Performance 5x13x4mm Ball Bearing (Rubber Case)(4PC) SWC-210082 SWORKz S35-3 Competition Ball Bearing Kit (Metal Case)(Set)(20PC)
SW-250050 SWORKz 1/8 Off Road Formula Bulkhead Wing (4PC)/ Front Upper Arm's Wing Set (4PC) SWC-210088 S35-3 Nitro Series Pro-composite Carbon One Unit Radio Tray Set
SW-250050A SWORKz 1/8 Off Road Formula Bulkhead Lexan Wing (0.8mm)(4PC) SWC-210082A SWORKz S35/GT Competition Ball Bearing Kit (Metal Case)(20PC)
SW-250041 S350 Falcon II Clean Body Shell SWC-340007 S35-3 Series Pro-composite Carbon Front Upper Done Force Wing Set
SW-2501116 SWORKz High Done Force Wing Set (BK)(Fit S350) SWC-330115A S350 Series Competition Titanium Steering Knuckle Pivot Ball Turnbuckle
SW-2501116A SWORKz High Done Force Wing Set (BK) SWC-338006 SWORKz Tornado Hi-Performance Lightened Clutch Bell (13T)
SW-2501116AFY SWORKz High Done Force Wing Set (FY) SWC-338020 SWORKz Tornado Hi-Performance Lightened Clutch Bell (14T)
SW-2501116AWH SWORKz High Done Force Wing Set (WH) SWC-338015 S35-3 T-7075AL Rear Hub Carry for Wide Suspension (R=L)(1pc)
SW-2501114-4 S35-3/S350 Nitro Series Center Brake Disk Holder SW-338036 SWORKz 1/8 Nitro Series Pipe Spring Lock (1 set)
SW-2501126 Ail Filter Set SW-338039 S35-3/4 Series Center HET Spur Gear (46T)
SW-2501529H S35/S350 Series Hard Plastic Chassis Brace Set SW-338041 S35-3/4 Series Center HET Spur Gear (48T)
SW-2503260FO S353 Series Colorful Plastic Inserts Set (FO) SW-338075 S35-4 Series T7 Aluminum Rear Wheel Hub (R=L)(2PC)
SW-2503260FY S353 Series Colorful Plastic Inserts Set (FY) SWC-115163 S35 Series Black Competition Front Shock Spring (M4-Dot)(75X1.6X8.75)
SW-2503260LB S353 Series Colorful Plastic Inserts Set (SB)(2 SET) SWC-115165 S35 Series Black Competition Front Shock Spring (M2-Dot)(75X1.6X9.25)
SW-2503270-01H S35-3 Series Front Upper Arms with Hard Material (2pc) SWC-115182 S35-4 Black Competition Front Shock Spring (US4-Dot)(62X1.6X7.5)
SW-210079AH S35-4 Plastic Center Big Bore HET Diff Case (Hard) SWC-115184 S35-4 Black Competition Front Shock Spring (US2-Dot)(62X1.6X8.0)
SW-210091H S35-4 Plastic Front/Rear Big Bore HET Diff Case (Hard) SWC-115164 S35 Series Black Competition Front Shock Spring (M3-Dot)(75X1.6X9.0)
SW-218005 S35-3/4 Series HET Center Big Bore Diff. Set (47T) SWC-115190 S35 Series Competition Black Line Rear Shock Spring (RM4-Dot)(80X1.6X9.75)
SW-218006 S35-4 Series HET Front/Rear Big Bore Diff. Set (43T) SWC-115192 S35 Series Competition Black Line Rear Shock Spring (RM2-Dot)(80X1.6X10.25)
SW-218008 S35-3 Series HET Diff. Combo Kit SWC-218007A S35 Series Evolution-CVA Drive Shaft Set 92.5mm (1 Sets)
SW-218016 S35-4/E BBS Pro Shock System Front Set SWC-218007D S35 Series Advance-CVD Drive Shaft Set 92.5mm (1 Sets)
SW-218017 S35-4/E BBS Pro Shock System Rear Set SWC-338071 S35 Series Advance-CVD Drive Axil(1PC)
SW-228005M-F S35-4 Series Front Lower Arm in Medium Material (1PC) SWC-338072 S35 Series Advance-CVD Drive Shaft (92.5mm)(1PC)
SW-228005M-R S35-4 Series Rear Lower Arm in Medium Material (1PC) SWC-338073 S35 Series Evolution-CVA Drive Axil(1PC)
SW-228005H-F S35-4 Series Front Lower Arm in Hard Material (1PC) SWC-338074 S35 Series Evolution-CVA Drive Shaft (92.5mm)(1PC)
SW-228005H-R S35-4 Series Rear Lower Arm in Hard Material (1PC) SWC-338076 S35 Series E-CVA/A-CVD Pin M2.5x14(2PC)
SW-228008WH SWORKz 1/8 Off Road Formula 2.0 Race Wing (WH) SWC-338077 S35-4 Series E-CVA/A-CVD Axil Join(2PC)
SW-228008FY SWORKz 1/8 Off Road Formula 2.0 Race Wing (FY) SWC-228012 1/8 E-CVD/A-CVA Axil Holder (10PC)
SW-300049 SWORKz S35-3/S350 Series Rear Stainless Chassis End Protection (2PC) SWC-218020-6LD S35 Series 1-Unit-Fit Aluminum Engine Mount Set (6 Degree Lay-Down)
SW-330006A Tornado Clutch Shoes (2set) SWC-218020-4LD S35 Series 1-Unit-Fit Aluminum Engine Mount Set (4 Degree Lay-Down)
SW-330115 Steering Knuckle Pivot Ball Turnbuckle SWC-338095 S35 Series 1-Unit-Fit Aluminum Engine Mount (6 Degree Lay-Down)
SW-330116 14mm Knuckle Pivot Ball SWC-338096 S35 Series 1-Unit-Fit Aluminum Engine Mount (Upper)(2PC)
SW-330125A S350 Series Aluminum Rear Upper Sus. Arm Ball Stud (4pc) SWC-338097 S35 Series 1-Unit-Fit Aluminum Engine Mount (4 Degree Lay-Down)
SW-330134A S350 Series Aluminum Shock Ball Stud (4pc)
SW-330136A S350 Series Aluminum Sway Bar Ball Stud (4pc)
SW-330168A S35-3 Series Rear Chassis Blance wight 15g (2pc)
SW-330202 S-WORKz Turbo Tornado Fly Wheel Set
SW-330398A SWORKz S350 Series Pro Wheel Nut (GM)
SW-330420 S350 Series Knuckle Pivot Ball Balance Nut (5.5g) (2pc)
SW-330424 S350 Series Aluminum Wing Holder (RED)
SW-330424B S350 Series Aluminum Wing Holder (BK)
SW-330424G S350 Series Aluminum Wing Holder (GM)
SW-330505A S35 Series Lightened Wheel Hub for 8mm Axil (L6.5mm)
SW-330506A S35 Series Lightened Wheel Hub for 8mm Axil (L5.0mm)
SW-330564A S35 Series BBS System Shock Piston 1.5mmX6 Holes (BK)
SW-330565 S350 BBS System Shock Piston 1.3mmX8 Oblique Holes (2pc)
SW-330566 S350 BBS System Shock Piston 1.2mmX8 Oblique Holes (2pc)
SW-330568 S350 Buggy Series Aluminum Center Diff. Mount
SW-330663 S35-3 Series Aluminum R-Center Drive Shaft (115mm)
SW-330767 S35-3 Series T-7075 Aluminum F-Center Dive Shaft (88mm)
SW-330777B S35-4 Series Aluminum Steering Linkage Ball Stud 7mm (L7) (4PC)
SW-350002A S35 Series BBS System Shock Piston 1.2mmX8 Straight Holes (BK)
SW-350003A S35 Series BBS System Shock Piston 1.3mmX8 Straight Holes (BK)
SW-338070A S35 Series Rear Upper Arm Aluminum Ball Stud (2PC)
SW-338078-25 SWORKz Uni-Design 2-Way System Aluminum Steering Servo Horn 25T
SW-338078-23 SWORKz Uni-Design 2-Way System Aluminum Steering Servo Horn 23T
SW-338079-25 SWORKz Uni-Design Aluminum Throttle Servo Horn 25T
SW-338079-23 SWORKz Uni-Design Aluminum Throttle Servo Horn 23T
SW-338080 S35/S350 Series Lightened Wheel Hub for 8mm Axil (L5.5mm)
SW-340003A S35-3 Series Pro-composite Carbon Front Upper Arm Cover (1.5mm)(2PC)
SW-400022A-M S35 Series BBS System Pro Shock Bladder (Medium)(8PC)
SW-410023 Air Filter Adapter
SW-400024S S35 Series BBS System Hex-Cell Shock Bladder(Soft)(4PC)
SW-400024M S35 Series BBS System Hex-Cell Shock Bladder(Medium)(4PC)
SWC-115107 S350 Competition Shock Spring A-2 (75X1.4X7.25)(Red)
SWC-115109 S350 Competition Shock Spring B-2 (90X1.4X8.5)(Pink)
SWC-115110 S350 Competition Shock Spring C-1 (75X1.5X7.75)(SkyBlue)
SWC-115118 S350 Competition Shock Spring E-3 (90X1.5X8.5)(Blue)
SWC-116006C SWORKz Competition 8x16x5mm Ball Bearing (Metal Case) (6PC)
SWC-116010C SWORKz Competition 5x10x4mm Ball Bearing (Metal Case) (6PC)

43
 Pa
E xp
r ts
l oNo.
d e d LView
is t

Shock Absorbers 2501121C 2501121C

108029 108029

Front 338067 338067

Rear
400022A-S 400023 400022A-S 400023

338061(S) 338062(L)

400019
330560B 400019
103004
330560B 103004
101011
330562A 101011
330563A

338063A 338062A
210058

210058
400020
330557
400020
330557

400010(S)
400009(L)

SWC-115183

228006 SWC-115164

330134
228006

330134

Differential 108003

330015
338040

610020

Center 400002
338028

116006R
328001 101039
101004

328001
101039

116006R 101004
338027
330015 338025
116006R

400002
108001
338024 F/R
101004
400002
210079A 610023 101004
338028 108001 328001
338025
328001 101004
101039
330015 101039
328001 400002
210091
338025 116006R
101004
328001
330015

338027

44
 Front Suspension

103001 108006
2501122B (25/24/23)
106007

330134 2501121C (#7)

2501121C (#7) 330134

106014 106007

338043 330155
116004R
610019
115004A
338052
103001
106007
330114A
101021
106007
117003
338053 101021

2501121C 117003
117003
330122A 330777A 330126A 106002
2501122B
106002 2503270 (#3)
106020 103001 2501122B
330124 338051
340003A 116004R 103001
2503260-04 2503260 338048
106002
330118A (#1 #2 #3 #4) 101019
108003 116004R
101018 330777A
108006
338048
108003
104010
330121B 330252 228006
2503270-01 108010
116006R
330118A 330119 340017 228002-2
106005
2503264A 106002 330767A
116006R 210046 228005S-F
338057
330661A 108001
2503260-04
106021A 228001
330252 (#11 #12 #13)
330117A
330243 338059
(Anti-Clockwise) 101018 106019R
338056 338023 104010 228001
338011 (#8 #9 #10)
105013A 106010
101010A 2503261A
108003
330138B
103003A 106019R
106015 108001 108012
101018
108001
2503261A
2501097B 106002
228001(#5 #6 #7)
2503260
2501121C 104004 (#1 #2 #3 #4) 2503270 (#3)
338058 338054 106020
330136 108012
101020A 330126A
108008 228001(#14 #15 #16) 340003A 330777A
330134 330119
330777A 2501121C
104005 104004
330136 2503270-01 106002
2503261A 2501121C
106013 330134 330252
115008A (2.3mm) 210046 338051
228005S-F
or
106002
115035A (2.2mm) 338056 2503260-04
116006R 2503264A
330118A
106021A 106005 101018
330124
330243
330117A

330252 330118A
116006R
330121B
2503260-04 104010

330122A

45
 Pa
E xp
r ts
l oNo.
d e d LView
is t

Center Transmission
105005 105005

2501126A 101013

106001 101013
2501126A
106001

2503262 610004

2501126A 330006 330008A

103003 330100A
115003A
108006 116010R
330137
116010R 115003A
101015
106008 106002 101012 101015
105007A
105001
108006
104011
106008 2502040

104004 106002 330140A

210033X
106002
200193 106020 108013
106002 2501115

106002

210033X 106009

2503262 210033X

108006

2503262
108006
106020
108003 2503260 104004
210018 SWC-330106
104004
2501125C 116009
330156A
104004 330090
106007
330156A
2503262 2503260
330104
104004
330157A 210018
2501112B 104004 116009
2503262 104004 330647 106007
103001 330156A
2503260 104004
210018 330104
2503260
104004
108006 330157A
108006 210018 2501124 210043
228004 2501112B 330156A
210043 SWC-330580
115098 115098
108007 210043
SWC-330580
210043
338047A

2501124
108007 106007

228004

108010

108003
108007

46
Rear Suspension

258001C-E 115019

115019

105025

228008BK

228008BK

106025

115005 (2.8mm)
330122A 330125 228006-5 or
115006 (2.6mm) 106013
330123A
2501121C 108019 104005
330124 2501121C 228003A(#3) 2501121C 104004 2503261A
330121B 340016 330136
106002
228001 106009 103001 106003
338070
330782
104010 228001 228003A
116006R (#17 #18) 330134 104004
2503260 103003A 103001
(#5 #6 #7) 330136
103001 210046 338068
101010A
2501121C
2503260 116006R 105006A 108008
(#5 #6 #7) 330243 330134
338014
108001
228001
(#17 #18) 228002-1 228005S-(R) 228003A 2503261A 228001(#2 #3 #4)
106005
103001
228006 106002 108001 108012
338056 106021A
108005 101018
106006 330399B 338050

103001 103001
106019R

2501529A
101018
106019R
338023
338011

2503261A
103001 330661A

330663A 106002
2501121C 228006-5
108001
108012
228001
(#2 #3 #4)
338049 338070 330123A
330125
210046 2501121C
340016
228005S-(R) 330243 106009
(Anti-Clockwise) 330782
228001

116006R
2503260
338056 (#5 #6 #7)
330124
106021A
228002-1
106005 103001 116006R
2503260 330121B
(#5 #6 #7)
228001 104010
(#17 #18)
330122A

47
508001 Production No. 35120205