Scribd
Upload
64 views5 pages

Relay Module Information

The document describes an ESP8266 eight-channel relay module development board equipped with an ESP-12F WiFi module that supports DC 7-28V/5V power supply and provides eight relay output channels and GPIO pins. It details the hardware, interfaces, pinouts and provides instructions for setting up the Arduino development environment and downloading programs.

Uploaded by

pkdudet
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
64 views5 pages

Relay Module Information

The document describes an ESP8266 eight-channel relay module development board equipped with an ESP-12F WiFi module that supports DC 7-28V/5V power supply and provides eight relay output channels and GPIO pins. It details the hardware, interfaces, pinouts and provides instructions for setting up the Arduino development environment and downloading programs.

Uploaded by

pkdudet
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 5

5V/7-28V ESP8266 WIFI 8 Channel Relay Module ESP-12F

Development Board Power Supply Wireless WIFI Module

Overview
ESP8266 eight-way relay development board equipped with ESP-12F WiFi module,
support DC7-28V/5V power supply mode. Provide Arduino development environment
reference code, suitable for ESP8266 secondary development learning, smart home
wireless control and other occasions.

Functional features
1, on-board mature and stable ESP-12F WiFi module, high-capacity 4M Byte Flash;
2, the power supply mode supports DC7-28V/5V;
3, on-board WiFi module RST reset button;
4, ESP-12F support the use of Eclipse/Arduino IDE and other development tools, to
provide reference programs under the Arduino development environment;
5, on-board 8-way 5V relay, output switching signals, suitable for controlling the control of
loads operating voltage of AC 250V/DC30V or less;
6, on-board power indicator and relay indicator.

1
Hardware introduction and description
1, board size: 148 * 79.8mm
Weight: 140g

2, Interface Introduction

2
Burning port: GND, RX, TX, 5V of ESP8266 are connected to GND, TX, RX, 5V of the
external TTL serial module respectively, IO0 needs to be connected to GND when
downloading, and then disconnect the connection between IO0 and GND after
downloading is completed;

Relay output:
NC: normally closed terminal, shorted to COM before the relay is absorbed, suspended
after absorption;
COM: common terminal;
NO: Normally open terminal, the relay is suspended before it is absorbed, and is shorted
to COM after it is absorbed.

3, Introduction of GPIO pinout ports


serial number name Functional Description
A/D conversion result. Input voltage range 0 to
1 ADC
1V, value range: 0 to 1024
2 IO2 GPIO2; UART1_TXD
3 TXD UART0_TXD; GPIO1
4 RXD UART0_RXD; GPIO3
5 GND POWER GROUND
6 5V 5V Power Supply

4, Arduino development environment construction


ESP8266 supports Eclipse/Arduino IDE and other development tools, the use of Arduino
to be relatively simple, the following is the Arduino development environment to build
methods:
1, install Arduino IDE 1.8.9 or the latest version;
2, open the Arduino IDE, click the menu bar File - Preferences, enter the Preferences in
the "additional development board manager URL" in the click to add the URL:

http://arduino.esp8266.com/stable/package_esp8266com_index.json,

3
3, click the menu bar of the Tools - Development Board - Development Board Manager,
and then search for "ESP8266" to install the Arduino ESP8266 support package 3.1.2 or
the latest version!

5, program download
1, use the jumper cap to connect IO0 and GND pins, prepare a TTL serial module (eg:
FT232) plugged into the computer USB, serial module and the development board
connection method is as follows:

TTL Serial Module ESP8266 Development Board

4
GND GND
TX RX
RX TX
5V 5V

2, click the menu bar Tools - Development Board, select the development board for
ESPino (ESP-12 module)
3, open the program you want to download, click Tools - Port in the menu bar, select the
correct port number.
4, click "Upload" and the program will be automatically compiled and downloaded to the
development board, as follows:

5, and finally disconnect IO0 and GND, the development board re-power or press the
reset button program can run.

You might also like