Datasheet UL865-EUD

We have 45,000 LP502030-PCM-NTC-LD-A02554 - EEMB - Lithium Battery Rectangular 3.
7V 250mAh Rechargeable in
stock now. Starting at $0.034. This EEMB part is fully warrantied and traceable.
00000005981LF-000
UL865NAD204T701
EOS Power
Telit
Buy Now
Buy Now
Looking for a discount?

Check out our current promotions!
Give us a call
1-855-837-4225 1-415-281-3866
International: 1-415-281-3866
1-555-555-5555
Arrow
Arrow Electronics,
Electronics, Inc
Verical Division
9201 East Dry Creek Road
P.O. Box 740970
Centennial,
Los Angeles, CO 80112
CA 90074-0970
This coversheet was created by Verical, a division of Arrow Electronics, Inc. (“Verical”). The attached document was created by the part supplier,
not Verical, and is provided strictly 'as is.' Verical, its subsidiaries, affiliates, employees, and agents make no representations or warranties
regarding the attached document and disclaim any liability for the consequences of relying on the information therein. All referenced brands,
product names, service names, and trademarks are the property of their respective owners.
UL865 Product Description
80420ST10586A Rev.4 – 2017-06-01
80420ST10586A - Rev.4 – 2017-06-01
APPLICABILITY TABLE
PRODUCT
UL865-EUR
UL865-EUD
UL865-NAR
UL865-NAD
UL865-N3G
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 2 of 33
80420ST10586A - Rev.4 – 2017-06-01
Disclaimer
The information contained in this document is the proprietary

information of Telit Communications S.p.A. and its affiliates
(“TELIT”).
The contents are confidential and any disclosure to persons
other than the officers, employees, agents or subcontractors
of the owner or licensee of this document, without the prior
written consent of Telit, is strictly prohibited.
Telit makes every effort to ensure the quality of the
information it makes available. Notwithstanding the foregoing,
Telit does not make any warranty as to the information
contained herein, and does not accept any liability for any
injury, loss or damage of any kind incurred by use of or
reliance upon the information.
Telit disclaims any and all responsibility for the application
of the devices characterized in this document, and notes that
the application of the device must comply with the safety
standards of the applicable country, and where applicable,
with the relevant wiring rules.
Telit reserves the right to make modifications, additions and
deletions to this document due to typographical errors,
inaccurate information, or improvements to programs and/or
equipment at any time and without notice.
Such changes will, nevertheless be incorporated into new
editions of this document.
Copyright: Transmittal, reproduction, dissemination and/or

editing of this document as well as utilization of its
contents and communication thereof to others without express
authorization are prohibited. Offenders will be held liable
for payment of damages. All rights are reserved.
Copyright © Telit Communications S.p.A. 2013.
80420ST10586A - Rev.4 – 2017-06-01
Contents
1. Introduction ................................................. 6
1.1. Scope ..................................................... 6
1.2. Audience .................................................. 6
1.3. Contact Information, Support .............................. 6
1.4. Text Conventions .......................................... 7
1.5. Related Documents ......................................... 7
1.6. Document History .......................................... 7
2. Overview ..................................................... 8
2.1. Product variants .......................................... 9
2.2. Target Market ............................................. 9
2.3. Features .................................................. 9
2.4. Approvals ................................................ 12
3. General Product Description ................................. 13

3.1. Dimensions and 2D mechanical drawing ..................... 13
3.2. Environmental requirements ............................... 14
3.2.1. Temperature range .......................................... 14
3.2.2. RoHS compliance ............................................ 14
3.3. Operating Frequency ...................................... 15
3.4. Transmitter output power ................................. 16
3.5. Supply voltage ........................................... 16
3.6. Power consumption ........................................ 17
3.7. Logic level .............................................. 17
3.8. Input and Outputs ........................................ 17
3.8.1. General Purpose I/Os ....................................... 17
3.8.2. Power on monitor (PWR_MON) ................................. 17
3.8.3. Power on/off control (ON_OFF) .............................. 18
3.8.4. Auxiliary power output for accessory (VAUX) ................ 18
3.8.5. SIM Reader ................................................. 18
3.8.6. Converters ................................................. 18
3.8.7. Audio Interface ............................................ 18
3.8.8. Serial ports ............................................... 18
3.8.9. USB port ................................................... 18
3.8.10. User Interface ........................................... 18
80420ST10586A - Rev.4 – 2017-06-01
3.9. Features ................................................. 18

3.9.1. Speech Coding .............................................. 18
3.9.2. SMS ........................................................ 19
3.9.3. RTC Bypass out ............................................. 19
3.9.4. Data Transmission capabilities ............................. 19
3.9.5. Local security management .................................. 19
3.9.6. Call control ............................................... 19
3.9.7. Phonebook .................................................. 19
3.9.8. Characters management ...................................... 20
3.9.9. SIM related functions ...................................... 20
3.9.10. Call status indication ................................... 20
3.9.11. Automatic answer ......................................... 20
3.9.12. Supplementary services ................................... 20
3.10. Mounting the modules on your board ..................... 20
3.11. Packing system ......................................... 21
4. Evaluation Kit .............................................. 22
5. AT Commands ................................................. 23
6. Safety Recommendations ...................................... 24
7. Conformity assessment issues ................................ 26

7.1. RTT&E Notified Body statement of Opinion ................. 28
7.2. FCC certificate .......................................... 29
7.3. IC certificates .......................................... 31
8. List of acronyms ............................................ 32
80420ST10586A - Rev.4 – 2017-06-01
1. Introduction
1.1. Scope
Scope of this document is to give an overview of the Telit
UL865 module, which can support GSM/GPRS/EDGE and WCDMA/HSPA
with data/voice capabilities.
1.2. Audience
This document is intended for customers who are evaluating the
UL865 product.
1.3. Contact Information, Support

For general contact, technical support, to report
documentation errors and to order manuals, contact Telit
Technical Support Center (TTSC) at:
[email protected]
[email protected]
[email protected]
[email protected]
Alternatively, use:
http://www.telit.com/en/products/technical-support-
center/contact.php
For detailed information about where you can buy the Telit
modules or for recommendations on accessories and components
visit:
http://www.telit.com
To register for product news and announcements or for product
questions contact Telit Technical Support Center (TTSC).
Our aim is to make this guide as helpful as possible. Keep us
informed of your comments and suggestions for improvements.
Telit appreciates feedback from the users of our information.
80420ST10586A - Rev.4 – 2017-06-01
1.4. Text Conventions
Danger – This information MUST be followed or catastrophic

equipment failure or bodily injury may occur.
Caution or Warning – Alerts the user to important points about

integrating the module, if these points are not followed, the
module and end user equipment may fail or malfunction.
Tip or Information – Provides advice and suggestions that may

be useful when integrating the module.
All dates are in ISO 8601 format, i.e. YYYY-MM-DD.
1.5. Related Documents

 UL865 Hardware User Guide, 1VV0301050
 Telit EVK2 User Guide, 1vv0300704
1.6. Document History
Revision Date Changes

0 2013-02-04 First issue
1 2014-01-07 Updated Ch. 2.1, 3.2. Added
certifications in Ch.7
2 2014-04-28 Layout of table at Ch.2.1. Ch.2.3
3 2017-03-01 Updated certificates for new SW release
4 2017-06-01 Updated RED certificates
Updated SAFETY RECOMMENDATIONS
80420ST10586A - Rev.4 – 2017-06-01
2. Overview
The UL865 Series further enriches the xL865 Family with a

number of UMTS/HSPA variants targeted at European (EMEA) and
North American (NA) markets. The dual-band UMTS/HSPA, dual-band
GSM/GPRS engine in the UL865 Series is voice-capable supporting
digital (DVI) interface. It delivers UMTS/HSPA 3GPP Release 7
compliant data communications and is equipped with a high-speed
USB 2.0 port, eight I/O ports, two A/D and one D/A converters.
For streamlined application development and system integration
the company offers RIL drivers for all major operating systems.
The UL865 features a VQFN packaging that is fully pad-level
compatible with its 2G companion, the GL865-DUAL V3.
As a part of Telit’s corporate policy of environmental
protection, all Telit products comply with the RoHS (Restriction
of Hazardous Substances) directive of the European Union (EU
Directive 2011/65/EU)
NOTE:
Some of the performances of the Telit modules depend on S/W
version installed on the module itself. The Telit modules S/W
group is continuously working in order to add new features and
improve the overall performances. The Telit modules are easily
upgraded by the developer using the Telit Flash Programmer.
NOTE:
In order to meet the competitive OEM and vertical market
stringent requirements, Telit supports its customers with a
dedicated Support Policy with:
 Telit Evaluation Kit EVK2 to help you to develop your
application;
 A website with all updated information available;
 An high level specialist technical support to assist you in
your development;
80420ST10586A - Rev.4 – 2017-06-01
2.1. Product variants

The following table describes the variants of UL865 series,
available for both EUx and NAx configurations as dual band in
2G&3G, plus an additional 3G-only variant for the North American
Market.
Freq. Bands Freq. Bands

Variants Features
2G (MHz) 3G (MHz)
UL865-EUR 900/1800 900/2100 Data&Voice
UL865-EUD 900/1800 900/2100 Data-only
UL865-NAR 850/1900 850/1900 Data&Voice
UL865-NAD 850/1900 850/1900 Data-only
UL865-N3G N.A. 850/1900 Data&Voice
2.2. Target Market

The UL865 is designed and developed for applications such as:
 Point-of-Sales (POS) terminals
 mHealth Monitoring
 Security alarms with cameras
 Battery powered devices
 Telemetry
 Telematics, including Mapping and Infotainment
 Handheld scanners and logistics devices
2.3. Features
 Advanced E-GPRS/WCDMA/HSDPA/HSUPA Software protocol stack

(Layer 1 to 3) – Version: 3GPP Release 7
80420ST10586A - Rev.4 – 2017-06-01
 GSM Quad band (900/1800 MHz for EUx, 850/1900 MHz for NAx)
 WCDMA dual-band: B1&B8 for the EUx models and B2&B5 for
the NAx models
 HSDPA up 7.2Mbps
 HSUPA up to 5.76Mbps
 WCDMA up to 384kbps downlink/uplink
 DTM (Dual Transfer Mode)
 CPC (DRX/DTX) (Continuous Packet Connectivity)
 DARP
 Control via AT commands according to 3GPP TS27.005, 27.007
and Telit customized AT commands
 Serial port multiplexer 3GPP TS27.010
 SIM application Tool Kits 3GPP TS 51.014
 Power consumption (typical values)
- Stand-by current 2G, DRX9, 1.2 mA
- Stand-by current 3G, DRX7, 1.8 mA
 Output power
- Class 4 (2W) @ 850 / 900 MHz, GSM
- Class 1 (1W) @ 1800 / 1900 MHz, GSM
- Class E2 (0.5W) @ 850/900 MHz, EDGE
- Class E2 (0.4W) @ 1800/1900 MHz, EDGE
- Class 3 (0.25W) @ 850/900/1900/2100 MHz, WCDMA
Interfaces
 I/O ports including multi-functional I/Os
 I2S for digital audio interface
 USB 2.0 HS
 1 UART
 1 Auxiliary serial port (RX/TX only)
 1 I2C
 1.8V/3V SIM interface
80420ST10586A - Rev.4 – 2017-06-01
Audio
 Telephony, emergency call
 HR, FR, EFR, AMR for GSM and AMR for WCDMA voice codec
 Spatial Noise Suppression
 Multiple audio profiles pre-programmed and fully
configurable
 DTMF
SMS
 Point to point mobile originated and mobile terminated SMS
 Concatenated SMS supported
 SMS cell broadcast
 Text and PDU mode
 SMS over GPRS
Data transmission
 HSPA: category 8 in downlink e category 6 in uplink
 DL up to 7.2Mbps
 UL up to 5.76Mbps
 WCDMA: up to 384kbps downlink/uplink
 Asynchronous non-transparent CSD up to 9.6kbps
 GPRS class 10 for NAx variants and class 33 for EUx
variants
 EDGE class 10 for NAx variants and class 33 for EUx
variants
 Coding scheme 1 to 4 (GPRS) & Modulation Coding scheme 1
to 9 (EDGE)
GSM Supplementary Services

 Call forwarding
 Call barring
 Call waiting & call hold
 Advice of charge
80420ST10586A - Rev.4 – 2017-06-01
 Calling line identification presentation [CLIP]

 Calling line identification restriction [CLIR]
 Unstructured supplementary services mobile originated
data [USSD]
 Closed user group
Additional features
 SIM phonebook
 Fixed Dialling Number (FDN)
 Call control & status indication
 SIM phonebook
 Character management (IRA, UCS2, GSM)
 USIM 3GPP Rel.7
 Real Time Clock
 Automatic answer
 Alarm management
 Embedded TCP/IP stack, including TCP, IP, UDP, and FTP
protocols
 CSD for Video Telephony support
2.4. Approvals
 Fully type approved confirming with R&TTE directive
 CE, GCF
 FCC, IC, PTCRB
 AT&T
 RoHS and REACH (all variants)
80420ST10586A - Rev.4 – 2017-06-01
3. General Product Description
3.1. Dimensions and 2D mechanical drawing

UL865 has a QFN package, with 48 pads.
The overall dimensions of UL865 are:

 Length: 24.4 mm
 Width: 24.4mm
 Thickness: 2.6 mm
80420ST10586A - Rev.4 – 2017-06-01
3.2. Environmental requirements

3.2.1. Temperature range
–40°C ~
Operating Temperature Range
+85°C
3.2.2. RoHS compliance

As a part of Telit corporate policy of environmental protection,
the UL865 complies with the RoHS (Restriction of Hazardous
Substances) directive of the European Union (EU directive
2011/65/EU). REACH compliant as well.
80420ST10586A - Rev.4 – 2017-06-01
3.3. Operating Frequency

The operating frequencies in GSM850, EGSM900, DCS1800, PCS1900,
WCDMA modes are compliant to the 3GPP and WCDMA specifications.
Mode Freq. TX Freq. RX Channels TX - RX

(MHz) (MHz) offset
GSM850 824.2 ~ 869.2 ~ 893.8 128 ~ 251 45 MHz

848.8
890.0 ~ 935.0 ~ 959.8 0 ~ 124 45 MHz

914.8
EGSM900
880.2 ~ 925.2 ~ 975 ~ 1023 45 MHz
889.8 934.8
DCS1800 1710.2 ~ 1805.2 ~ 512 ~ 885 95MHz

1784.8 1879.8
PCS1900 1850.2 ~ 1930.2 ~ 512 ~ 810 80MHz

1909.8 1989.8
Tx: 4132 ~
WCDMA850 826.4 ~ 4233
871.4 ~ 891.6 45MHz
(band V) 846.6 Rx: 4357 ~
4458
Tx: 2712 ~
WCDMA900
882.4 ~ 2863
(band 927.4 ~ 957.6 45MHz
912.6 Rx: 2937 ~
VIII)
3088
Tx: 9262 ~
WCDMA1900 1852.4 ~ 1932.4 ~ 9538
80MHz
(band II) 1907.6 1987.6 Rx: 9662 ~
9938
Tx: 9612 ~
WCDMA2100 1922.4 ~ 2112.4 ~ 9888
190MHz
(Band I) 1977.6 2167.6 Rx: 10562 ~
10838
80420ST10586A - Rev.4 – 2017-06-01
3.4. Transmitter output power

The UL865 transceiver output of GSM/GPRS mode in 850/900MHz
bands are class 4 in accordance with the specifications which
determine the nominal 2W peak RF power (+33dBm) on 50ohm. In the
1800/1900MHz bands are class 1 in accordance with the
specification which determines the nominal 1W peak RF power
(+30dBm) on 50ohm.
The UL865 transceiver output of EDGE mode in 850/900MHz bands
are class E2 in accordance with the specifications which
determine the nominal 0.5W peak RF power (+27dBm) on 50ohm. In
the 1800/1900MHz bands are class E2 in accordance with the
specification which determine the nominal 0.4W peak RF power
(+26dBm) on 50ohm.
The UL865 transceiver output of WCDMA mode in
850/900/1900/2100MHz bands is class 3 in accordance with the
specifications which determine the nominal 0.25W peak RF power
(+24dBm) on 50ohm.
3.5. Supply voltage

The external power supply must be connected to VBATT signal and
must fulfill the following requirements:
Nominal Supply Voltage 3.8V

Operating Voltage Range 3.4 ~ 4.2V
Extended Operating Voltage
3.22 ~ 4.5V
Range
CAUTION:
The operating voltage MUST not be exceeded; Special care must
be taken when designing the application’s power supply section
to avoid an excessive voltage drop. If the voltage drop is
exceeding the limits it could cause a Power Off of the module.
80420ST10586A - Rev.4 – 2017-06-01
3.6. Power consumption

The UL865 power consumptions are described in the following
table
Depending on network configuration and not under module control
3.7. Logic level

Where not specifically stated, the most of interface circuits
work at 1.8V CMOS logic levels. To get more detailed information
about the logic level specifications used for UL865, please
refer to the Hardware User Guide.
3.8. Input and Outputs

3.8.1. General Purpose I/Os
Pins of general purpose I/Os can be configured by AT command in
three different ways as input, output and alternative function.
3.8.2. Power on monitor (PWR_MON)

The PWR_MON indicates the status of the module running properly.
80420ST10586A - Rev.4 – 2017-06-01
3.8.3. Power on/off control (ON_OFF)

External power on/off control input. Refer to the Hardware User
Guide for more details of Power on timing.
3.8.4. Auxiliary power output for accessory (VAUX)

A regulated 1.8V power output is provided for an external
device.
3.8.5. SIM Reader

The UL865 family supports 1 SIM/USIM at 1.8V and 3V ONLY with
and external SIM connector. For 5V SIM, an external level
translator can be added. Refer to the UL865 Hardware User Guide.
3.8.6. Converters
The UL865 family has 2 ADC and 1DAC.
3.8.7. Audio Interface

A Digital Audio bus is available.
3.8.8. Serial ports

Two serial ports are available.
 Full RS232-C
 Auxiliary serial port (RX/TX only)
3.8.9. USB port

The USB2.0 High Speed has a clock rate of 480MHz
3.8.10. User Interface

The user interface is managed by AT commands according to ITU-T
V.250, 3GPP 27.007 and 27.005 specifications. Please refer to
the AT command User Guide for complete details.
3.9. Features
3.9.1. Speech Coding
The UL865 support the following voice codecs:
 Adaptive Multi Rate for WCDMA
 Half Rate, Full Rate, Enhanced Full Rate, Adaptive Multi
Rate for GSM
80420ST10586A - Rev.4 – 2017-06-01
3.9.2. SMS
The UL865 supports the following SMS types:
 Mobile Terminated (MT) class 0 ~ 3 with signaling of new
incoming SMS, SIM full, SMS read
 Mobile Originated class (MO) 0 ~ 3 with writing, saving in
SIM and sending
 Cell broadcast compatible with CB DRX signaling of new
incoming SMS.
The module supports also SMS over GPRS
3.9.3. RTC Bypass out

The VRTC pin brings out the Real Time Clock supply, which is
separate from the rest of the digital part, allowing having
only RTC going on when all the other parts of the device are
off.
To this power output a backup capacitor can be added in order
to increase the RTC autonomy during power off of the battery.
NO Devices must be powered from this pin.
3.9.4. Data Transmission capabilities

The UL865 supports:
 HSPA: D/L up to 7.2Mbps, U/L up to 5.76Mbps
 Asynchronous non-transparent CSD up to 9.6kbps for GSM,
14.4kbps for WCDMA
 EDGE Class 10 for NAx variants and Class 33 for EUx
variants
 Coding scheme 1 to 4 (GPRS) & Modulation Coding scheme 1
to 9 (EDGE)
3.9.5. Local security management

The local security management can be done with the lock of
Universal Subscriber Identity Module (USIM), and the security
code will be requested at power-up.
3.9.6. Call control

The calling cost control function is supported.
3.9.7. Phonebook
This function allows storing the telephone numbers into SIM
memory. The capability depends on the SIM version and its
embedded memory.
80420ST10586A - Rev.4 – 2017-06-01
3.9.8. Characters management

The UL865 supports the IRA, GSM, PCCP437, 8859-1 and UCS2
character sets, EXT and PDU mode.
3.9.9. SIM related functions

Activation and deactivation of the numbers stored in phone book
FDN (Fixed Dialing Numbers), ADN (Abbreviated Dialing Number)
and PIN insertion are supported. Extension at the PIN2 for the
PUK2 insertion capability for lock condition is supported too.
3.9.10. Call status indication

The call status indication is supported.
3.9.11. Automatic answer

The automatic answering feature is supported. The
user/application can specify the number of rings after which the
module will make an answer automatically.
3.9.12. Supplementary services

The following supplementary services are supported:
 Call Barring
 Call Forwarding
 Calling Line Identification Presentation (CLIP)
 Calling Line Identification Restriction (CLIR)
 Call Waiting, other party call Waiting Indication
 Call Hold, other party Hold/Retrieved Indication
 Closed User Group supplementary service (CUG)
 Advice of Charge
 Unstructured SS Mobile Originated (MO)
3.10. Mounting the modules on your board

The modules have been designed in order to be compliant with a
standard lead-free SMT process. For detailed information about
PCB pad design and conditions to use in SMT process, please
refer to the respective Hardware User Guide.
80420ST10586A - Rev.4 – 2017-06-01
3.11. Packing system

According to SMT process, for picking & placing movement
requirements, UL865 is packaged on trays. Each tray contains 20
pieces in size of 176 x 329.
The level of moisture sensibility of UL865 is “3”, according
with standard IPC/JEDEC J-STD-020, take care of all the relative
requirements for using this kind of components. Special care for
handling is highly required.
80420ST10586A - Rev.4 – 2017-06-01
4. Evaluation Kit
In order to assist the customer in the development of the
application, Telit offers the EVK2 Evaluation Kit that can be
ordered separately. The EVK2 has a SIM card holder, the RS 232
serial port level translator, a direct UART connection, audio
and antenna connector.
The EVK2 provides a fully functional solution for a complete
data or phone application. The standard serial RS232 9 pin
connector placed on the Evaluation Kit allows the connection of
the EVK2 system with a PC or other DTE.
The development of the applications utilizing the Telit UL865
must present a proper design of all the interfaces towards and
from the module (e.g. power supply, audio paths, level
translators), otherwise a decrease in the performances will be
introduced or, in the worst case, a wrong design can even lead
to an operating failure of the module.
In order to assist the hardware designer in his project phase,
the EVK2 board presents a family of different solutions, which
will cover the most common design requirements on the market,
and which can be easily integrated in the OEM design as building
blocks or can be taken as starting points to develop a specific
one.
For a detailed description of the Telit Evaluation Kit, please
refer to the documentation provided with the respective Hardware
User Guide and EVK2 User Manual.
80420ST10586A - Rev.4 – 2017-06-01
5. AT Commands
The UL865 can be driven via the serial and USB interface using
the standard AT commands.
The modules are compliant with:
1. Hayes standard AT command set, in order to maintain the
compatibility with existing S/W programs.
2. 3GPP TS 27.007 specific AT command and WCDMA/GPRS specific
commands.
3. 3GPP TS 27.005 specific AT commands for SMS (Short Message
Service) and CBS (Cell Broadcast Service)
Moreover, the modules support also Telit proprietary AT commands

for special purposes.
For more information about the AT commands supported by the
modules, please refer to the AT Commands Reference Guide.
80420ST10586A - Rev.4 – 2017-06-01
6. Safety Recommendations
READ CAREFULLY
Be sure the use of this product is allowed in the country and

in the environment required. The use of this product may be
dangerous and has to be avoided in the following areas:
 Where it can interfere with other electronic devices in
environments such as hospitals, airports, aircrafts, etc.
 Where there is risk of explosion such as gasoline
stations, oil refineries, etc. It is responsibility of
the user to enforce the country regulation and the
specific environment regulation.
Do not disassemble the product; any mark of tampering will
compromise the warranty validity. We recommend following the
instructions of the hardware user guides for a correct wiring
of the product. The product has to be supplied with a
stabilized voltage source and the wiring has to be conforming
to the security and fire prevention regulations. The product
has to be handled with care, avoiding any contact with the
pins because electrostatic discharges may damage the product
itself. Same cautions have to be taken for the SIM, checking
carefully the instruction for its use. Do not insert or remove
the SIM when the product is in power saving mode.
The system integrator is responsible of the functioning of the
final product; therefore, care has to be taken to the external
components of the module, as well as of any project or
installation issue, because the risk of disturbing the
WCDMA/GSM network or external devices or having impact on the
security. Should there be any doubt, please refer to the
technical documentation and the regulations in force. Every
module has to be equipped with a proper antenna with specific
characteristics. The antenna has
to be installed with care in order to avoid any interference
with other electronic devices and has to guarantee a minimum
distance from the body (20 cm). In case of this requirement
cannot be satisfied, the system integrator has to assess the
final product against the SAR regulation.
The European Community provides some Directives for the

electronic equipments introduced on the market.
All the relevant information’s are available on the European
Community website:
https://ec.europa.eu/growth/single-market/european-
standards/harmonised-standards/rtte_en
80420ST10586A - Rev.4 – 2017-06-01
The Directive 2014/53/EU regarding radio equipment is available at:
https://ec.europa.eu/growth/sectors/electrical-engineering/red-
directive_en
while the applicable Directives (Low Voltage and EMC) are available at:
https://ec.europa.eu/growth/sectors/electrical-engineering/lvd-
directive_en
https://ec.europa.eu/growth/sectors/electrical-engineering/emc-
directive_en
80420ST10586A - Rev.4 – 2017-06-01
7. Conformity assessment issues
80420ST10586A - Rev.4 – 2017-06-01
80420ST10586A - Rev.4 – 2017-06-01
7.1. RTT&E Notified Body statement of Opinion
80420ST10586A - Rev.4 – 2017-06-01
7.2. FCC certificate
80420ST10586A - Rev.4 – 2017-06-01
80420ST10586A - Rev.4 – 2017-06-01
7.3. IC certificates
80420ST10586A - Rev.4 – 2017-06-01
8. List of acronyms
3GPP 3rd Generation Partnership Project

ADC Analog to Digital Converter
ADN Abbreviated Dialing Number
A-GPS Assisted GPS
AMR Adaptive Multi Rate
AT Attention Commands
AWS Advanced Wireless Services
BER Bit Error Rate
BGA Ball Grid Array
CLIP Calling Line Identification Presentation
CLIR Calling Line Identification Restriction
CMOS Complementary Metal-Oxide Semiconductor
CSD Circuit Switched Data
DAC Digital to Analog Converter
DARP Downlink Advanced Receiver Performance
DTMF Dual Tone Multi Frequency
FDN Fixed Dialing Number
FTP File Transfer Protocol
GSM Global System for Mobile communication
GPRS General Packet Radio Service
GPS Global Positioning System
HSPA High Speed Packet Access
HSUPA High Speed Uplink Packet Access
H/W Hardware
LED Light Emitting Diode
MO Mobile Originated
MT Mobile Terminated
OEM Other Equipment Manufacturer
80420ST10586A - Rev.4 – 2017-06-01
PCB Printed Circuit Board

PCM Pulse Code Modulation
PDA Personal Digital Assistant
PDU Protocol Data Unit
PIN Personal Identification Number
POS Point Of Sales
PWM Pulse Width Modulation
RF Radio Frequency
RoHS Restriction of Hazardous Substances
RTC Real Time Clock
SAIC Single Antenna Interface Cancellation
SIM Subscriber Identity Module
SMD Surface Mounted Device
SMS Short Message Service
S/W Software
TBD To Be Determined
TCP/IP Transmission Control Protocol/Internet Protocol
TTSC Telit Technical Support Center
UART Universal Asynchronous Receiver and Transmitter
USB Universal Serial Bus
USIM Universal Subscriber Identity Module
WCDMA Wideband Code Division Multiple Access

Datasheet UL865-EUD

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Datasheet UL865-EUD

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Datasheet UL865-EUD

Uploaded by

Copyright:

Available Formats

We have 45,000 LP502030-PCM-NTC-LD-A02554 - EEMB - Lithium Battery Rectangular 3.

Looking for a discount?

The information contained in this document is the proprietary

Copyright: Transmittal, reproduction, dissemination and/or

Copyright © Telit Communications S.p.A. 2013.

3. General Product Description ................................. 13

3.9. Features ................................................. 18

4. Evaluation Kit .............................................. 22

6. Safety Recommendations ...................................... 24

7. Conformity assessment issues ................................ 26

8. List of acronyms ............................................ 32

1.3. Contact Information, Support

1.4. Text Conventions

Danger – This information MUST be followed or catastrophic

Caution or Warning – Alerts the user to important points about

Tip or Information – Provides advice and suggestions that may

All dates are in ISO 8601 format, i.e. YYYY-MM-DD.

1.5. Related Documents

1.6. Document History

Revision Date Changes

The UL865 Series further enriches the xL865 Family with a

2.1. Product variants

Freq. Bands Freq. Bands

UL865-EUR 900/1800 900/2100 Data&Voice

UL865-EUD 900/1800 900/2100 Data-only

UL865-NAR 850/1900 850/1900 Data&Voice

UL865-NAD 850/1900 850/1900 Data-only

UL865-N3G N.A. 850/1900 Data&Voice

2.2. Target Market

 Advanced E-GPRS/WCDMA/HSDPA/HSUPA Software protocol stack

GSM Supplementary Services

 Calling line identification presentation [CLIP]

3. General Product Description

3.1. Dimensions and 2D mechanical drawing

The overall dimensions of UL865 are:

3.2. Environmental requirements

3.2.2. RoHS compliance

3.3. Operating Frequency

Mode Freq. TX Freq. RX Channels TX - RX

GSM850 824.2 ~ 869.2 ~ 893.8 128 ~ 251 45 MHz

890.0 ~ 935.0 ~ 959.8 0 ~ 124 45 MHz

DCS1800 1710.2 ~ 1805.2 ~ 512 ~ 885 95MHz

PCS1900 1850.2 ~ 1930.2 ~ 512 ~ 810 80MHz

3.4. Transmitter output power

3.5. Supply voltage

Nominal Supply Voltage 3.8V

3.6. Power consumption

Depending on network configuration and not under module control

3.7. Logic level

3.8. Input and Outputs

3.8.2. Power on monitor (PWR_MON)

3.8.3. Power on/off control (ON_OFF)

3.8.4. Auxiliary power output for accessory (VAUX)

3.8.5. SIM Reader

3.8.7. Audio Interface

3.8.8. Serial ports

3.8.9. USB port