Peneseal PRO

PENESEAL PRO™:
Peneseal Pro™is a spray applied liquid sealer which

forms a sub-surface barrier that protects concrete
against water penetration and seals existing cracks up
to 2 mm. When sprayed onto a thoroughly cleansed
concrete surface, it will react with the concrete to form
a sub-surface barrier. This reaction product seals the
pores, capillaries and cracks. As long as water is
present, the product will remain active and seal future
hairline cracks.
RECOMMENDED FOR:
• Concrete roofs
• Podium decks
• Bridge decks
• Terraces
• Traffic bearing structures
• Runways
• Driveways
ADVANTAGES:
• Seals existing cracks up to 2.00 mm; New hairline cracks will be
sealed on contact with water.
• Protects against water, chloride and sulfate ingress; Increases
resistance against chemical attack, carbonation and efflorescence. Will
resist diluted acid or alkali attack.
• Sub-surface nature does not affect bond with subsequent product
applications.
• Increases surface hardness (approx. 20 mm depth) to 8 on Moh's
scale.
• Simple, Fast and Economical application compared to alternative
membrane systems. Peneseal Proª is water soluble & complies with
environmental, health & safety regulations.
• Trafficable within 6 hours after first water curing without affecting
protection. Will not peel or scratch and can be polished. No negative
screed necessary.
APPENDIX - 1
• Non-Toxic---Can be applied to potable water containing structures.
• Remaining structural defects can easily be found and repaired.
TECHNICAL PROPERTIES:
Packaging: 25 or 200 liter drums
Color: Transparent
Specific Gravity: Approx. 1.12
Shelf Life: No limit in sealed drums.
• Keep pails closed and avoid extended exposure to direct
sunlight. Do not allow to freeze.
• Non-toxic and biodegradable
• Non-explosive, non-flammable
• No known ill effects if swallowed.
APPLICATION PROCEDURES:
Surface Preparation:
• Surface damage, such as honeycombs, voids, etc. must be routed out
& repaired with Penecreteª mortar.
• Surface should be minimum 14 days old (28 days is recommended),
clean, free of dust and dry (no damp areas!)
• Any formwork oil, curing compounds or previous treatments should be
completely removed.
• Temperature should be between +5ºC and +35ºC.
• Avoid application when rain is imminent or in heavy wind.
• Old concrete and concrete affected by carbonation may need to be
treated with calcium for adequate reaction.
Application Instructions: Always agitate the product before use.
1. Flood cracks with Peneseal Proª at approx. 1 Liter/5 Linear Meters.
2. Apply product to surface at the recommended coverage rate. Spray

at low pressure and in low wind conditions.
3. When surface is dry to the touch (2-6 hours after application) flood
surface with abundant water. If it rains before the product is dry, a
second application is required after drying.
4. 24 hours later, flood surface with abundant water again.
5. Another 24 hours later, flood surface with abundant water yet again.
6. After third flooding, the treated area can be ponded to verify the
waterproofing performance.
Coverage:
APPENDIX - 2
1 liter to 4-6 sq. meters (4 for rough and porous surfaces, 6 for very
smooth, dense surfaces and 5 for normal surfaces)
Cracks: additional 1 liter per 5 linear meters.
Equipment: This can range from simple hand spraying equipment for
small areas to motorized spray units for large projects. With a simple
backpack spray unit, a coverage of 100-150 sqm per hour can be
achieved. After application, all equipment should be thoroughly cleaned
with water. Contact your ICS/PENETRON INTERNATIONAL LTD.
representative for details on spraying equipment.
NOTES:
• Peneseal Proª should not be used as a replacement or a solution for
poor design, detailing or workmanship.
• Peneseal Proª is not suitable for repair of structural or design cracks.
For cold joints, expansion joints, penetrations and pour joints, products
such as Penecreteª, waterstops, & elastomeric sealants should be
applied in addition to Peneseal Proª. (See back page for details).
• For floor hardening, use Penetron¨ Liquid Floor Hardener instead.
• Penetron¨ , not Peneseal Proª should be used for negative side
waterproofing.
• Peneseal Proª can be used on concrete that contains fly ash, slag or
silica fume, unless these ingredients exceed 30% of the total
cementitious materials in the concrete mix. Before use, try on a small
area or obtain concrete mix design. To increase suitability, a calcium
treatment may be applied to the surface. This will also increase
effectiveness on old and heavily carbonated concrete.
• Large cracks should be ponded with Peneseal Proª by creating a small
dam.
• Avoid skin and eye contact. If contact is made, flush areas with lots of
water. Protective gloves should be worn. Breathing apparatus is
advised if applied in enclosed environments.
• Do not spray Peneseal Proª onto glass, aluminum, wood or painted
surfaces. In case this happens, remove the product with water.
WARRANTY:
ICS/Penetron International, Ltd. warrants that the products
manufactured by it shall be free from material defects and will be
consistent with its normal high quality. Should any of the products be
proven defective, the liability of the manufacturer shall be limited to the
replacement of the product ex-factory. The Manufacturer makes no
warranty as to the merchantability or fitness for a particular purpose and
this warranty is in lieu of all other warranties expressed or implied. The
user shall determine the suitability of the product for his intended use
and assume all risks and liability in connection herewith.
APPENDIX - 3
APPENDIX - 4

Peneseal PRO

Uploaded by

Copyright:

Available Formats

Peneseal PRO

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Peneseal PRO

Uploaded by

Copyright:

Available Formats

PENESEAL PRO™:

Peneseal Pro™is a spray applied liquid sealer which

Application Instructions: Always agitate the product before use.

1. Flood cracks with Peneseal Proª at approx. 1 Liter/5 Linear Meters.

2. Apply product to surface at the recommended coverage rate. Spray

4. 24 hours later, flood surface with abundant water again.

Cracks: additional 1 liter per 5 linear meters.

You might also like