5-MASTER Rheobuild 858

Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

Rheobuild 858

High range, water reducing superplasticiser for rheoplastic concretes

MATERIAL DESCRIPTION TYPICAL PROPERTIES


MasterRheobuild 850 is formulated from synthetic Color : Dark Brown Liquid
polymers specially designed to impart rheoplastic Specific Gravity : 1.210 at 25°C
qualities to concrete. Chloride Content : Chloride-free to EN934-2
A rheoplastic concrete is a fluid concrete with a slump Freezong Point : 0°C
of at least 200mm, easily flowing, but at the same time
free from segregation and having the same STANDARD
water/cement ratio as that of a low slump concrete
EN 934-2 Tables 3.1, 3.2, 11.1 and 11.2
(25mm) without admixture. MasterRheobuild 850 is
ASTM C-494 Type A, B, D, F and G
chloride free.
DOSAGE
ADVANTAGES Optimum dosage of MasterRheobuild 850 should be
MasterRheobuild 850 considerably improves the determined in trial mixes. As a guide the following dosages
properties of fresh and hardened concrete. are recommended as a starting point for any trial. In normal
concrete a dosage of between 0.8-2.0 litre / 100kg total
PRIMARY USES cementitious material. In high performance micro silica
• Microsilica concrete concrete a dosage of between 1.5-3.0 litre / 100kg total
• Mass concrete pours cementitious material. Dependant upon mix requirement, it
• Ready mixed concrete is possible to use a higher dosage of MasterRheobuild 850
• Long-distance transport without causing any adverse effects upon the concrete.
• Pumped concrete Please consult MASTER BUILDERS SOLUTIONS
• Casting in hot climates PAKISTAN PRIVATE LIMITED’s Technical staff for further
information.
To obtain
• Reduced thermal peaks
• High workability for longer periods DISPENSING
• Lower pumping pressure MasterRheobuild 850 is a ready-to-use liquid which is
• Delayed setting with longer workability dispensed into the concrete together with the mixing
• Higher ultimate strengths. water. The plasticising effect and water reduction are
• Reduced permeability higher if the admixture is added to the concrete after 50
• Improved durability to 70% of the mixing water has been added. The
addition of MasterRheobuild 850 to dry aggregate or
COMPATIBILITY cement is not recommended. Automatic dispensers are
available.
MasterRheobuild 850 is compatible with all cements
and most air entraining agents meeting the ASTM
standards. The addition of MasterRheobuild 850 and WORKABILITY
MasterAir 100 (air entraining agent) to concrete is MasterRheobuild 850 ensures that rheoplastic concrete
recommended where it is required to withstand freezing remains workable in excess 3 hours at
and thawing cycles. +20°C.

Workability loss is dependent on temperature, and on the


PACKAGING type of cement, the nature of aggregates, the method of
MasterRheobuild 850 is available in bulk or in 210 litre transport and initial workability. It is strongly
drums. recommended that concrete should be properly cured
particularly in hot and dry climates.

June 2120 Page 1 of 3


Rheobuild 858
High range, water reducing superplasticiser for rheoplastic concretes

STORAGE
MasterRheobuild 850 must be stored where temperatures
do not drop below +5°C. If product has frozen thaw and
agitate until completely reconstituted. Store under cover,
out of direct sunlight and protect from extremes of
temperature.

Failure to comply with the recommended storage


conditions may result in premature deterioration of the
product or packaging. For specific storage advice consult
MASTER BUILDERS SOLUTIONS PAKISTAN PRIVATE
LIMITED's Technical Service Department.

SAFETY PRECAUTION
MasterRheobuild 850 is not a fire or health hazard.
Spillages should be washed down immediately with cold
water. For further information refer to the material safety
data sheet.

NOTE
Field service, where provided, does not constitute
supervisory responsibility. For additional information
contact your local MASTER BUILDERS SOLUTIONS
PAKISTAN PRIVATE LIMITED representative.

MASTER BUILDERS SOLUTIONS PAKISTAN PRIVATE


LIMITED reserves the right to have the true cause of any
difficulty determined by accepted test methods.

QUALITY AND CARE


All products MASTER BUILDERS SOLUTIONS
PAKISTAN PRIVATE LIMITED’s Products are
manufactured under a management system
independently certified to conform to the requirements of
the quality, environmental and occupational health and
safety standards of ISO 9001 and MASTER BUILDERS
SOLUTIONS PAKISTAN PRIVATE LIMITED’s ESHQ
recommendations.

* Properties listed are based on laboratory controlled


tests.

® = Registered trademark of the MBS-Group in many


countries.

June 2120 Page 2 of 3


Rheobuild 858
High range, water reducing superplasticiser for rheoplastic concretes

DISCLAIMER
The technical information and application advice given in this MBS publication are based on the present state of our best scientific and
practical knowledge. As the information herein is of a general nature, no assumption can be made as to a product's suitability for a particular
use or application and no warranty as to its accuracy, reliability or completeness either expressed or implied is given other than those
required by law. The user is responsible for checking the suitability of products for their intended use.

Field service where provided does not constitute supervisory responsibility. Suggestions made by MBS either orally or in writing may be
followed, modified or rejected by the owner, engineer or contractor sincethey, and not MBS, are responsible for carrying out procedures
appropriate to a specific application.

Master Builders Solutions Pakistan (Pvt) Ltd


46-A, Block-6, 75400 Karachi, Pakistan
Tel: +92 21 38892103
https://www.master-builders-solutions.com/en-pk

June 2120 Page 3 of 3

You might also like