DASHBOARD PAGE:

A. PELLET PHASE SYSTEM.

B. PELLET TRANSPORT SYSTEM.
1. Manual Auto Button for mode Pellet Phase System.
2. Indicator status of Pellet Phase System.
3. Manual Auto Button for mode Pellet Transport System.
4. Indicator status of Pellet Transport System.
5. Current Recipe name for using now and button save.
6. Indicator monitoring for some parameters.
7. Manual Command running and stop for motors in Pellet System Phase.
8. Manual Command running and stop for motors in Pellet Transport Phase.
9. Manual Command ON OFF for Cylinder Cooler.
10. Indicator of DUMP active.
11. Value monitoring speed of motor product feeder.
12. Indicator of Motor Product Feeder running and Feedback of motor product feeder.
13. Indicator of Motor Conditioner and Feedback of Motor Conditioner.
14. Value monitoring percentage open for Automatic Steam Valve.
15. Actual Monitoring for capacity of production.
16. Actual Monitoring for Steam Temperature of Conditioner.
17. Actual Monitoring for Motor Pellet Mill Current.
18. Indicator of Motor Pellet Mill and Feedback of Motor Pellet Mill.
19. Actual Monitoring of Temperature in Cooler Tank.
20. Indicator of Sensor Cooler.
21. Indicator of Vibrator Motor and Feedback of Vibrator Motor.
22. Indicator of Motor Pocket Feeder and Feedback of Motor Pocket Feeder.
23. Indicator of Motor Crumble and Feedback of Motor Crumble.
24. Indicator of Motor Baling” and Feedback of Motor Baling”.
25. Indicator of Motor Blower and Feedback of Motor Blower.
26. Sensor indicator for valve screener active.
27. Sensor indicator for valve return to hopper active.
28. Indicator of Motor Screener and Feedback of Motor Screener.
29. Indicator of Sensor Return to Cooler.
30. Indicator of Sensor Return to Hopper.
31. Manual Valve from screener to hopper or Hopper to Screener.
32. Manual Valve from Cooler to Hopper or Hopper to Cooler.
33. Indicator of Sensor Safety Slip.
34. Indicator of Motor Bucket Elevator and Feedback of Motor Bucket Elevator.
35. Alarm indicator when some Alarm or Alert coming.
36. Command Start and Stop for Pellet Phase System.
37. Command Start and Stop for Pellet Phase System.
38. Reference to Home Page.
39. Reference to Dashboard Page.
40. Reference to Setting Parameters Page.
41. Reference to Manual Run Page.
42. Reference to Recipe Page.
43. Reference to Alarm History Page.
44. Reference to IO Maps Page.
LOGIN PAGE:
1. Form for fill username before Login Page.
2. Form for fill password before Login Page.
3. Button for Login to Next Page.
4. Login information status.
HOME PAGE:
1. Alarm message indicator and information.
2. Acknowledge button for alarm message.
3. All Acknowledge Button for acknowledge all alarm.
4. Button Detail for see detail of alarm in alarm history.
5. Username Login and Logout Button.
6. Current Recipe name for using now.
7. Button Save
8. Reference to Home Page.
9. Reference to Dashboard Page.
10. Reference to Setting Parameters Page.
11. Reference to Manual Run Page.
12. Reference to Recipe Page.
13. Reference to Alarm History Page.
14. Reference to IO Maps Page.
SETTING AND PARAMETERS
1. Alarm message indicator and information.
2. Acknowledge button for alarm message.
3. All Acknowledge Button for acknowledge all alarm.
4. Button Detail for see detail of alarm in alarm history.
5. Username Login and Logout Button.
6. Current Recipe name for using now.
7. Button Save
8. Reference to Home Page.
9. Reference to Dashboard Page.
10. Reference to Setting Parameters Page.
11. Reference to Manual Run Page.
12. Reference to Recipe Page.
13. Reference to Alarm History Page.
14. Reference to IO Maps Page.
15. Parameter timer for delay when motor is running. (ex: when motor screener running, motor
bucket elevator on after VALUE TIMER DELAY ON)
16. Parameter timer for delay when motor is stop. (ex: when motor elevator stop, motor
screener will stop after VALUE TIMER DELAY STOP)
17. Parameter timer for waiting signal feedback after motor on. (ex: when motor elevator on,
contactor will send signal feedback to PLC until VALUE TIMER DELAY FEEDBACK, if VALUE
TIMER DELAY FEEDBACK was achieved but PLC not received that signal then Motor will off,
and alarm will come)
18. Parameter timer for alarm changing bagging. (ex: When we changing in bagging area from
return to hopper then change to return to cooler but sensor return to cooler is not active
until VALUE TIMER DELAY BAGGING then the alarm will be coming).
19. Parameter timer for alarm changing screener. (ex: When we changing in screener area from
return to hopper then change to Screener but sensor screener is not active until VALUE
TIMER DELAY CHANGING SCREENER then the alarm will be coming).
20. Parameter timer for safety slip in bucket elevator.
21. Enable Disable button for using PID in temperature steam and automatic steam valve in
conditioner area.
22. Set Point value for PID temperature steam.
23. Actual result for automatic steam valve open.
24. Actual result for temperature steam.
25. Parameter for manual open percentage automatic steam valve, these parameters will be use
if we disable PID method for temperature steam and automatic steam valve.
26. Parameter for minimum scaling temperature steam.
27. Parameter for maximum scaling temperature steam.
28. Actual result for temperature steam.
29. Parameter for minimum scaling ampere meter reading in Motor Pellet Mill.
30. Parameter for maximum scaling ampere meter reading in Motor Pellet Mill.
31. Actual result for ampere meter reading in Motor Pellet Mill.
32. Set Point value for DUMP open.
33. Set Point value for alarm limit ampere meter in Motor Pellet Mill.
34. Parameter for minimum scaling ampere meter reading to convert in tonnage.
35. Parameter for maximum scaling ampere meter reading to convert in tonnage.
36. Actual result for actual weight in production tonnage.
37. Set Point value for production tonnage.
38. Enable Disable Button for synchronize velocity for Motor product feeder.
39. Actual speed for Motor Product Feeder.
40. Manual speed value for Motor Product Feeder, this parameter will use if we disable the
function of synchronize velocity for Motor Product Feeder.
41. Parameter for minimum scaling temperature cooler.
42. Parameter for maximum scaling temperature cooler.
43. Actual result for temperature cooler.
RECIPE PAGE:
1. Alarm message indicator and information.
2. Acknowledge button for alarm message.
3. All Acknowledge Button for acknowledge all alarm.
4. Button Detail for see detail of alarm in alarm history.
5. Username Login and Logout Button.
6. Current Recipe name for using now.
7. Button Save
8. Reference to Home Page.
9. Reference to Dashboard Page.
10. Reference to Setting Parameters Page.
11. Reference to Manual Run Page.
12. Reference to Recipe Page.
13. Reference to Alarm History Page.
14. Reference to IO Maps Page.
15. Button Save for save the recipe.
16. Button Save As for Save As the current recipe with new recipe name.
17. Button New for make new Recipe.
18. Button Delete for Delete Recipe
19. Button Rename for rename the name of Recipe.
20. Button Load for load Recipe before start production.
21. Button Export for save all recipe to external memory or hardware.
22. Button Import for import or put Recipe from external memory or hardware.
23. For choose what Recipe will use.
24. Number id of Recipe.
25. Parameters of Recipe.
ALARM HISTORY PAGE:
1. Alarm message indicator and information.
2. Acknowledge button for alarm message.
3. All Acknowledge Button for acknowledge all alarm.
4. Button Detail for see detail of alarm in alarm history.
5. Username Login and Logout Button.
6. Current Recipe name for using now.
7. Button Save
8. Reference to Home Page.
9. Reference to Dashboard Page.
10. Reference to Setting Parameters Page.
11. Reference to Manual Run Page.
12. Reference to Recipe Page.
13. Reference to Alarm History Page.
14. Reference to IO Maps Page.
15. Detail of alarm history.
IO MAPS PAGE:
1. Reference to Home Page.
2. Reference to Dashboard Page.
3. Reference to Setting Parameters Page.
4. Reference to Manual Run Page.
5. Reference to Recipe Page.
6. Reference to Alarm History Page.
7. Reference to IO Maps Page.
8. IO Maps in DI/DO CPU PLC.
9. IO Maps in Extension digital input module.
10. IO Maps in Extension digital output module.