DBTV2500

SERVICE MANUAL
COLOR TELEVISION RECEIVER

ORIGINAL
MFR’S VERSION B

Design and specifications are subject to change without notice.

More user manuals on ManualsBase.com

 DBTV2500

SERVICE MANUAL
COLOR TELEVISION RECEIVER

REVISION 1
MFR’S VERSION D

MFR’S VERSION IC101

B OEC7044A
D OEC7045A

Please file this revision with the original version.

More user manuals on ManualsBase.com

 Change of IC101

DIFFERENCES

MFR'S VERSION B MFR'S VERSION D

REF. NO. PART NO. DESCRIPTION PART NO. DESCRIPTION
IC101 I56F07044A IC OEC7044A I56F07045A IC OEC7045A
PCB010 A3I058G01A MAIN PCB ASS'Y TMX456A A3I058G01B MAIN PCB ASS'Y TMX456A

SPEC.NO. M3I0-62G
O/R NO. A073521

More user manuals on ManualsBase.com

 SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
2. AVOID AN ELECTRIC SHOCK ripheral circuit, use the designated parts and
There is a high voltage part inside. Avoid an make sure not modify the circuit.
electric shock while the electric current is Repairing except indicates causes rising of high
flowing. voltage, and it emits an X-ray from the cathode-
ray tube.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific 7. PERFORM A SAFETY CHECK AFTER
characters of incombustibility and withstand SERVICING
voltage for safety. Therefore, the part which is
replaced should be used the part which has Confirm that the screws, parts and wiring which
the same character. were removed in order to service are put in the
Especially as to the important parts for safety original positions, or whether there are the
which is indicated in the circuit diagram or the portions which are deteriorated around the
table of parts as a mark, the designated serviced places serviced or not. Check the
parts must be used. insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER (INSULATION CHECK PROCEDURE)
ASSEMBLING OR WIRING 1. Unplug the plug from the AC outlet.
There are parts which use the insulation 2. Remove the antenna terminal on TV and turn
material such as a tube or tape for safety, or on the TV.
which are assembled in the condition that 3. Insulation resistance between the cord plug
these do not contact with the printed board. terminals and the eternal exposure metal
The inside wiring is designed not to get closer [Note 2] should be more than 1M ohm by
to the pyrogenic parts and high voltage parts. using the 500V insulation resistance meter
Therefore, put these parts in the original [Note1] .
positions. 4. If the insulation resistance is less than 1M
ohm, the inspection repair should be
5. TAKE CARE TO DEAL WITH THE required.
CATHODE-RAY TUBE [Note 1]
In the condition that an explosion-proof cathode- If you have not the 500V insulation
ray tube is set in this equipment, safety is resistance meter, use a Tester.
secured against implosion. However, when
[Note 2]
removing it or serving from backward, it is
External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to
deal with it.

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.

IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.

A1-1

More user manuals on ManualsBase.com

 CONTENTS

SERVICING NOTICES ON CHECKING ...................................................................................................... A1-1

HOW TO ORDER PARTS ........................................................................................................................... A1-1
IMPORTANT ................................................................................................................................................ A1-1
CONTENTS ................................................................................................................................................. A2-1
GENERAL SPECIFICATIONS .................................................................................................................... A3-1~A3-4
DISASSEMBLY INSTRUCTIONS ............................................................................................................... B-1, B-2
SERVICE MODE LIST ................................................................................................................................. C-1
CONFIRMATION OF USING HOURS ......................................................................................................... C-1
NOTE FOR THE REPLACING OF MEMORY IC ........................................................................................ C-1
ELECTRICAL ADJUSTMENTS .................................................................................................................. D1-1~D2-1
MAJOR COMPONENTS LOCATION GUIDE ............................................................................................. D3-1
BLOCK DIAGRAM ...................................................................................................................................... E-1, E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT........................................................................................................................................... F-1~F-4
SCHEMATIC DIAGRAMS
MICON/TUNER .................................................................................................................................. G-1, G-2
CHROMA ........................................................................................................................................... G-3, G-4
DEFLECTION/CRT ............................................................................................................................ G-5, G-6
POWER ............................................................................................................................................. G-7, G-8
SOUND .............................................................................................................................................. G-9, G-10
WAVEFORMS ............................................................................................................................................. H-1, H-2
MECHANICAL EXPLODED VIEW .............................................................................................................. I-1
MECHANICAL REPLACEMENT PARTS LIST .......................................................................................... J1-1
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................ J2-1, J2-2

A2-1

More user manuals on ManualsBase.com

 GENERAL SPECIFICATIONS
G-1.Outline of the Product
25 inch( 626 mmV):Measured diagonally
Color CRT 100 degree deflection
G-2.Broadcasting System
US System M
G-3.Color System NTSC PAL SECAM or Monochrome signal
G-4.NTSC Playback(PAL 60Hz) Yes No
G-5.NTSC 3.58+4.43/PAL60Hz Yes No
G-6.Antenna Input Impedance
VHF/UHF 75 ohm unbalanced
G-7.Tuner and Receiving Contactless Electric tuner 1Tuner System
2Tuner System
channel Tuner Oscar(W/O HYPER) Oscar(W/ HYPER)
France CATV) Others
Receiving channel
(USA) 2-69 , 4A , A-5~A-1 , A~I , J~W , W+1~W+84
Tuning System
Frequency syn. Voltage syn. Others
G-8.Preset Channel
-- channels
G-9.Intermediate Frequency
Picture(fP) 45.75 MHz MHz MHz
Sound (fS) 41.25 MHz MHz MHz
fP-fS 4.50 MHz MHz MHz
G-10.Stereo/Dual TV Sound
Yes( NICAM GERMAN USA JAPAN) No
G-11.Tuner Sound Muting Yes No
G-12.Power Source 120 V AC 50Hz AC 60Hz
G-13.Power Consumption: 115 W at AC 120 V 60 Hz
W at DC V
Stand by: 8 W at AC 120 V 60 Hz
Per Year: - kWh / Year
G-14.Dimensions(Approx.)
618 mm(W) 504 mm(D) 525 mm(H)
G-15.Weight(Approx.) Net : 27 kg ( 59.9 lbs)
Gross: 29 kg ( 64.3 lbs)
G-16.Cabinet Material
Cabinet Front: PS 94HB DECABROM
ABS 94V2 NON-DECA
94V0
Back Panel: PS 94HB DECABROM
ABS 94V2 NON-DECA
94V0

A3- 1

More user manuals on ManualsBase.com

 GENERAL SPECIFICATIONS
G-17.Protector: Power Fuse
G-18.Regulation
Safety
UL CSA SAA SI CE SEV
BS NF NEMKO FEMKO DEMKO IEC65
SEMKO NZ HOMOLO SABS CNS SISIR
NOM AS3159 DENTORI UNE GOST NONE
Radiation
FCC DOC FTZ PTT CE SEV
SABA SI NF NZ HOMOLO UNE
CNS CISPR13 DENTORI AS/NZS NONE
X-Radiation
PTB DHHS HWC DENTORI NONE
G-19.Temperature
Operation 5 ˚C~ 40 ˚C
Storage -20 ˚C~ 60 ˚C
G-20.Operating Humidity Less than 80 %RH
G-21.Clock and Timer
Sleep Timer Yes Max 120 Min.( 10 Min. Step) No
On/Off Timer Yes Programs No
Wake Up Timer Yes Programs No
G-22.Timer back up Time
More than -- Minutes (at Power Off Mode)
G-23.Terminals
VHF/UHF Antenna Input Din Type F-Type France Type
Front Video Input (RCA ø8.3)
Rear Video Input (RCA ø8.3)
Rear Video Output (RCA ø8.3)
Front Audio Input (RCA ø8.3)
Rear Audio Input (RCA ø8.3)
Rear Audio Output (RCA ø8.3)
21 Pin DC Jack(Center +) Ear Phone Jack(ø3.5)
Head Phone Jack(ø3.5) AC Outlet Ext Speaker
Diversity S Input(Front) S Input(Rear)
G-24.Indicator
Power Stand By On Timer NONE
( ) ( ) ( )
G-25.Display
On Screen Display
Menu Clock Set( 12H 24H) System Selec On/Off Timer
Hotel Lock Area Code CH Tuning
Sound 1/2 NICAM Auto Off Picture
Guide CH Set Audio Language
CATV Pin Code Registration V-Chip
Control Level Sound Brightness Contrast
Color Tint(NTSC Only) Sharpness
Tuning Bass Treble
Balance Back Light
Stereo,Audio Output,Bilingual Picture Menu
Stereo,Audio Output, SAP Mid Night Theater
Stereo,Audio Output GAME
AV Channel Clock Hotel Lock
Sleep Timer Sound Mute Pin Code

A3- 2

More user manuals on ManualsBase.com

 GENERAL SPECIFICATIONS
G-26.OSD Language
Eng Ger Fre Spa Ita Por Jpn
OSD Language Setting
Eng Ger Fre Spa Ita Por Jpn
Not Applicable
G-27.Speaker
P os i t i on Front Side Bottom
Size 1.5 x 2.7 inches
Imp. 4 ohm x 2 pcs
Power Max 075 + 0.75 W
10% 0.5 + 0.5 W (Typical)
G-28.EXT Speaker
Yes -- W Imp -- ohm
G-29.Carton
Master Carton: Need No Need
Content: ---- Set
Material: ---- / ---- Corrugated Carton
Dimensions: ---- mm(W) ---- mm(D) ---- mm(H)
Description of Origin Yes No
Gift Box
Material Double/Brown Corrugated Carton ( with Photo Label)
Double/White Corrugated Carton ( with Photo Label)
Double Full Color Carton W/Photo
Dimensions: 689 mm(W) 577 mm(D) 620 mm(H)
Design: As Per BUYER 's
Description of Origin: Yes No
Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height 25cm 31cm 46cm 62cm 80cm
Container Stuffing: 204 Sets / 40' container
G-30.Accessories
Owner's Manual ( W/Guarantee Card) [ English/French ]
AC Plug Adapter Channel Film
Battery (UM- 4 x 2 ) Remote Control Unit
Safety Tip Toll Free Insert Sheet
Guarantee Card Audio-Video Cord (RCA)
Registration Card Warning Sheet
Quick Set-Up Sheet Schematic Diagram
Information Sheet U/V Mixer
75 ohm Coaxial Cable ( Single Shield Double Shield)
300 ohm to 75 ohm VHF Antenna Adaptor
21pin Cable Car Cord
Rod Antenna
One Pole Two Pole ( F-Type Din Type France Type)
Loop Antenna ( F-Type Din Type France Type)
G-31.Other Features
Auto Degauss Auto Search Full OSD
Auto Shut Off CH Allocation Premiere
Canal+ SAP Comb Filter
CATV(181CH) Channel Lock Auto CH Memory
Anti-Theft Just Clock Function Hotel Lock
Rental Game Position Fastext
Unitext TopText Closed Caption
Picture Menu Mid Night Theater V-Chip

A3- 3

More user manuals on ManualsBase.com

 GENERAL SPECIFICATIONS
G-32.Switch
Front
Power(Tact) Channel Up/Reset Volume Up/Set Up
System Select Channel Down/Enter Volume Down/Set Down
Main Power SW Sub Power Menu:Vol UP + Vol Down
Rear
AC/DC TV/CATV Selector
Degauss Main Power SW
G-33.Magnetic Field
BV : +0.45G BV : +0.35G BV : +0.25G
BH : 0.18G BH : 0.30G BH : 0.30G
BV : -0.15G BV : -0.25G BV : -0.50G
BH : 0.15G BH : 0.15G BH : 0.30G
G-34.Remote Control Unit: RC- 74
Glow in Dark Remocon Yes No
Power Source: D.C 3 V Battery UM - 4 x 2
Total 26 Key
Power Quick View TV/AV
Stand By Status Bar Select
0 Time Select PAL/SECAM
1 Time Set Volume Up
2 Muting Volume Down
3 CH Skip CH Call
4 CH1/CH2 CH Down
5 Channel CH Up
6 Text/Mix/TV CH Down/Page Down
7 Display Cancel CH Up/Page Up
8 Initial Page +/-
9 Store Program
10 Reveal F/T/B
11 Sleep Hold
12 Aft/Skip List
1 Preset Rotate
2 5.5/6.5MHz Browse
0/10 Auto Memory Std/Auto
Tone 1/2 Auto Memory
Info Call Band Select
Mono/Auto Reset Search
TV/Caption/Text Menu Clock/Program
Expand Enter Clock/Set
Red Add Ch Set
Cyan Delete Set +
Normal Yellow Set -
Color System Random Green
Wide Selecy Tuning Up/Time Text Nicam/Mono
Auto Wide On/Off Tuning Down/Reset Tone A/B
Picture Position Navi FM Transmitter
Direct Change/Auto Search Back Light
Picture Menu Mid Night Theater Audio Select

A3- 4

More user manuals on ManualsBase.com

 DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap
amount of alcohol. (Refer to Fig. 1-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a Location of Anode Cap
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.

GND on the CRT

Fig. 1-3

NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver CRT
Support
Alligator Clip

GND on the CRT

Fig. 1-1

2. Flip up the sides of the Rubber Cap in the direction of the

arrow and remove one side of the support.
(Refer to Fig. 1-2.)

Rubber Cap

Fig. 1-4

CRT
Support
Fig. 1-2

B-1

More user manuals on ManualsBase.com

 DISASSEMBLY INSTRUCTIONS
4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 1-5.

Support
CRT
Fig. 1-5

5. Confirm that the Support is securely connected.

6. Put on the Rubber Cap without moving any parts.

2. REMOVAL OF DEFLECTION YOKE

(Refer to Fig. 2-1)
1. Loosen the screw 1.
2. Remove the Convergence • Purity Magnet in the
direction of arrow (A).
3. Loosen the screw 2.
4. Remove the 3 Wedges.
5. Remove the Deflection Yoke in the direction of arrow
(B).

2
Wedge 1
(B)
(A)

Convergence •
Purity Magnet
Deflection Yoke
Wedge

Fig. 2-1

INSTALLATION
Install new Deflection Yoke in reverse steps of REMOVAL.
NOTE
After adjusting the purity and the convergence, fix the
screw 2 and lock the wedges.

B-2

More user manuals on ManualsBase.com

 SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.

Set Key Remocon Key Operations

VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
Initialization of the factory.
VOL. (-) MIN 1
NOTE: Do not use this for the normal servicing.

POWER ON total hours is displayed on the screen.

Refer to the "CONFIRMATION OF USING HOURS".
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".

Writing of EEPROM initial data.

VOL. (-) MIN 8
NOTE: Do not use this for the normal servicing.

Display of the Adjustment MENU on the screen.

VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

CONFIRMATION OF USING HOURS

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
ADDRESS DATA
1. Set the VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel INIT 00 83 Initial setting content of MEMORY IC.
button (6) on the remote control for more than 1 second.
3. After the confirmation of using hours, turn off the power. CRT ON 0010 POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
FIG. 1 + (ones digit value)

NOTE FOR THE REPLACING OF MEMORY IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.

INI INI INI INI INI INI INI INI INI INI INI
ADDRESS
00 01 02 03 04 05 06 07 08 09 0A
DATA A0 01 A2 09 02 63 24 18 A1 21 44

Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
3. ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using SET + or - until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.

C-1

More user manuals on ManualsBase.com

 ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS
ADJUSTMENTS 2-1: RF AGC DELAY
Read and perform these adjustments when repairing the 1. Receive an 80dB monoscope pattern.
circuits or replacing electrical parts or PCB assemblies. 2. Connect the digital voltmeter to TP001.
CAUTION 3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (02) on the remote control to
• Use an isolation transformer when performing any select "RF DELAY".
service on this chassis. 4. Press the VOL. UP/DOWN button on the remote control
• Before removing the anode cap, discharge electricity until the digital voltmeter is 1.80 ± 0.05V.
because it contains high voltage.
• When removing a PCB or related component, after 2-2: CUT OFF
unfastening or changing a wire, be sure to put the wire
back in its original position. 1. Adjust the unit to the following settings.
Inferior silicon grease can damage IC's and transistors. R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
• When replacing IC's and transistors, use only specified B.BIAS=64, BRIGHTNESS=126, CONTRAST=100.
silicon grease (YG6260M). 2. Place the set with Aging Test for more than 15 minutes.
Remove all old silicon before applying new silicon. 3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
Prepare the following measurement tools for electrical select "CUT OFF".
adjustments. 4. Adjust the Screen Volume until a dim raster is obtained.
1. Synchro Scope
2. Digital Voltmeter 2-3: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
On-Screen Display Adjustment
1. Place the set with Aging Test for more than 10 minutes.
1. In the condition of NO indication on the screen. 2. Receive the with 100% signal from the pattern generator.
Press the VOL. DOWN button on the set and the 3. Using the remote control, set the brightness and contrast to
Channel button (9) on the remote control for more than normal position.
1 second to appear the adjustment mode on the screen 4. Activate the adjustment mode display of Fig. 1-1 and press
as shown in Fig. 1-1. the channel button (10) on the remote control to select
"R.BIAS".
5. Using the VOL. UP/DOWN button on the remote control,
TV adjust the R.BIAS.
6. Press the CH. UP/DOWN button on the remote control to
select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".
7. Using the VOL. UP/DOWN button on the remote control,
adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS.
8. Perform the above adjustments 6 and 7 until the white
00 OSD 15 color is looked like a white.
Fig. 1-1
2-4: FOCUS
2. Use the Channel UP/DOWN button or Channel button
1. Receive the monoscope pattern.
(0-9) on the remote control to select the options shown
2. Turn the Focus Volume fully counterclockwise once.
in Fig. 1-2.
3. Adjust the Focus Volume until picture is distinct.
3. Press the MENU button on the remote control to end
the adjustments.
2-5: SUB TINT/SUB COLOR
1. Receive the color bar pattern.
NO. FUNCTION NO. FUNCTION
2. Connect the synchro scope to TP023.
00 OSD H 13 BRIGHTNESS
3. Activate the adjustment mode display of Fig. 1-1 and
01 CUT OFF 14 CONTRAST
press the channel button (16) on the remote control to
02 RF DELAY 15 COLOR
select "TINT".
03 VIF VCO 16 TINT
4. Press the VOL. UP/DOWN button on the remote control
04 H VCO 17 SHARPNESS
until the waveform becomes as shown in Fig. 2-1.
05 H PHASE 18 FM LEVEL
5. Connect the synchro scope to TP022.
06 V SIZE 19 LEVEL
6. Press the CH DOWN button once to set to "COLOR"
07 V SHIFT 20 SEPARATION 1
mode.
08 R DRIVE 21 SEPARATION 2
7. Press the VOL. UP/DOWN button on the remote control
09 B DRIVE 22 TEST MONO
until the red color level is adjusted to 110% of the white
10 R BIAS 23 TEST STEREO
level. (Refer to Fig. 2-2)
11 G BIAS 24 X-RAY TEST
12 B BIAS
Fig. 1-2

D1-1

More user manuals on ManualsBase.com

 ELECTRICAL ADJUSTMENTS

TV

Fig. 2-1
00 OSD 15

A B Fig. 2-3
0%

2-9: OSD HORIZONTAL

110% 1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote
control until the difference of A and B becomes
minimum. (Refer to Fig. 2-3)
100%
Fig. 2-2 2-10: VERTICAL VCO
1. Place the set with Aging Test for more than 15 minutes.
2-6: HORIZONTAL PHASE 2. Receive an 80dB monoscope pattern.
3. Connect the digital voltmeter between the pin 5 of
1. Receive the center cross signal from the Pattern
CP601.
Generator.
4. Activate the adjustment mode display of Fig. 1-1 and
2. Using the remote control, set the brightness and
press the channel button (03) on the remote control to
contrast to normal position.
select "VIF VCO".
3. Activate the adjustment mode display of Fig. 1-1 and
5. Press the VOL. UP/DOWN button on the remote control
press the channel button (05) on the remote control to
until the digital voltmeter is 2.5V.
select "H.PHASE".
4. Press the VOL. UP/DOWN button on the remote
2-11: SUB BRIGHTNESS
control until the SHIFT quantity of the OVER SCAN on
right and left becomes minimum. 1. Receive the black pattern*. (RF Input)
2. Activate the adjustment mode display of Fig. 1-1 and
2-7: VERTICAL SIZE press the channel button (13) on the remote control to
NOTE: Adjust after performing adjustments in section 2-6 select "BRIGHTNESS".
3. Press the VOL. UP/DOWN button on the remote control
1. Receive the crosshatch signal from the Pattern unit the screen begin to shine.
Generator.
2. Using the remote control, set the brightness and
2-12: SUB CONTRAST
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and 1. Receive the color bar pattern.
press the channel button (06) on the remote control to 2. Activate the adjustment mode display of Fig. 1-1 and
select "V.SIZE". press the channel button (14) on the remote control to
4. Press the VOL. UP/DOWN button on the remote control select "CONTRAST".
until the rectangle on the center of the screen becomes 3. Press the VOL. UP/DOWN button on the remote control
square. unit the nit for more than 200 nit.
5. Receive a broadcast and check if the picture is normal.

2-8: VERTICAL SHIFT

NOTE: Adjust after performing adjustments in section 2-7
1. Receive the crosshatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1
and press the channel button (07) on the remote control to
select "V.SHIFT".
4. Press the VOL. UP/DOWN button on the remote
control until the horizontal line becomes fit to the notch
of the shadow mask.

D1-2

More user manuals on ManualsBase.com

 ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 3-2.
1. Turn the unit on and let it warm up for at least 30 1. Receive the crosshatch pattern from the color bar
minutes before performing the following adjustments. generator.
2. Place the CRT surface facing east or west to reduce the 2. Combine red and blue of the 3 color crosshatch pattern
terrestrial magnetism. on the center of the screen by adjusting the pair of
3. Turn ON the unit and demagnetize with a Degauss Coil. 4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted 3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar
generator. 1. Adjust the differences around the screen by moving
3. Slide the deflection yoke until it touches the funnel the deflection yoke upward/downward and right/left.
side of the CRT. (Refer to Fig. 3-2-a)
4. Adjust center of screen to green, with red and blue on the 2. Insert three wedges between the deflection yoke and
sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 3-2-b)
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern RGB RGB
on the center of the screen by adjusting the pair of
4 pole magnets.
7. Combine red/blue (magenta) and green by adjusting the R
pair of 6 pole magnets. G
8. Adjust the crosshatch pattern to change to white B
R
by repeating steps 6 and 7. G
B
3-2: PURITY
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE
Adjust after performing adjustments in section 3-1. Fig. 3-2-a

1. Receive the green raster pattern from color bar

generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide. WEDGE WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw. WEDGE

DEFLECTION YOKE
WEDGE POSITION
DEFLECTION YOKE SCREW
MAGNET SCREW Fig. 3-2-b

PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1

D2-1

More user manuals on ManualsBase.com

 MAJOR COMPONENTS LOCATION GUIDE

TU001

FB401
TP001

CP601

FOCUS VOLUME
SCREEN VOLUME
MAIN PCB

TP023 TP024
J801
TP022

CRT PCB

D3-1

More user manuals on ManualsBase.com

 BLOCK DIAGRAM
Q351
MUTE SW.
TU001
CH UP CHROMA IC

AGC
SDA
SCL
X602 IC601 M61203BFP

IF
3.579545MHz IC351 AN7523
VOL UP 11 5 4 1 32 X' TAL
AUDIO OUT 50 6 2
CH DOWN MICON IC 62 RF AGC OUT SOUND IC SP351
IC101 OEC7044A CF601 9 4
SAW FILTER 64 VIF IN (1)
VOL DOWN 5 AUDIO MUTE Q606
1 VIF IN (2)
26 KEY2 REG OUT 33 REG. P. CON+15V
POWER CVIN 17 40 Y SW OUT Q801
27 KEY1 RED R 42 30 R IN R OUT 14 RED OUT
GREEN G 41 28 G IN G OUT 15 Q803
BLUE B 40 20 B IN B OUT 16 GREEN OUT
OS101 Q603
BLANK BL 39 27 FAST BLK Q802
REG OUT 41 REG.
1 10 REMOCON BLUE OUT
2 H. SYNC 1 12 INV FBP OUT FBP IN 6
Q608
3 V. SYNC 2 29 V PULSE OUT
START UP 19 CUT OFF
SCL1 34 5 SCL VCC
36 POWER SDA1 32 10 SDA H OUT 7
19 XIN RESET 25 42 MCU RESET
X101 Q402
8MHz 5 6 VREG VCC 55
MEMORY IC
20 XOUT SDA SCL IC199 17 V OUT H. DRIVE
S-24C02BDP-1A Q401
Q501 Q101
X_RAY_TEST 30 H. OUTPUT
POWER X-RAY TEST SW
V-OUT IC
IC401 LA78041
POWER REG. IC
IC501 PUMP UP 11 6 8
STR30110
- B G R
AMP CRT
DEGAUSS COIL
+ Heater
4 3 L502
Q403 VCC 10 F 9
D501~D504 X-RAY TEST SW. 7 5 6 2
+B RECTIFIER

RY101 IC402
KIA7805API
1 4
P. CON+5V
REG IC DY
2 3 1 3

FB401
D127 L501
P. CON+5V 4 9
3 1
D404 1 F
5 2
5 S
10 HV

F501 3

AC IN

E-1 E-2

More user manuals on ManualsBase.com

 F-2

W006 R501_1
C506_1

FH501

D501
*

D504
6.3A125V

Q401
F501

C503
L501
CP502

FH502

C501
C443 TH501 R802 CP501
C504
1

TP022
R428_

R815
Q801

W003 D502
R427

R803
R502

CC004

C444 D101
R804
TP024

W891
W897

D503
W014

Q802

R805
R806

D103
FB401

RY101

L801
TP023

W079
W004

SW105

R807
L406

Q803

C437
S803X

W838
CP802B
R640
R655

C416
W019

CP806

D125 W802
D404
D422

D408
D410

C802_1
D407

CP803B
T401_1
R429_1

D609
C401

HS401
R422
MAIN/CRT (INSERTED PARTS)

C507

W806
PRINTED CIRCUIT BOARDS

C132_1

W011
C404

C412

W018 C446
C647
R412

Q402
R410

C435
C439 01
CP401_1

J8
W061

SW104
D617

W103 C440
W021 00
6
R446
W020 C433 C 1
1_
SOLDER SIDE

W085 C
C427 80
W104 CP
2
W815 00
R443_1

D411 CC
CP803A

R404
W801

SW103
W818

IC401

R405 W070
W088

W007
W074

C405

S106X
C418
C133

S803Y
D126

R408
C115

W029
R407_2

R401
W831

W078
W022 R418 C646 C119

C129
D127

R424 W820
S809Y

Q501
S801X
R417

C125
C430 L101
R177
W824

SW102
X101_1
R135
Q403

R409 W028
R643
D401

W027 C122
D405

W005 W060
TP501

D402

D608
W026
W017 C417_1 C130
R506

C351
R448_1

C422
HS501

C121
IC501

15

Q101
W812

SW101
D104
R5

D403
R416 C124
R509

W095
R503

W059

C448 W097 W030 W069

W817

W090 W098 C128

R434_1 W031 W032

IC199
*

R445_1
CP802A

D602
W823

C414 W025
R508

D614
D601 C613_1
W024
R421_1 C434 W055

W071
R632
R507_1 R623 C640
W015 W073
C645
W083 W047 W023 C118 W045 W067
C519 W043
W046

Q603
W108
IC402
W082 W058 C638 W044
W010

C661
S801Y
W835 C352 W051
C123
C353_1 W052 W093 C610
W063 C622 S105X
W813

C625
D607 C627
W049 D615
C357_1 C609

W092
S802X C619_1

IC351_1

C630
D604 W040

C359_1
C654
W033 C614 X602

Q351
W814 Q608

D603
C635

CP351_1

C631

W041
W034

Q606
CP601

S104X

W042
C003 W810 D616 R644
C004

CF603
R647

W805

D612
R002
R001

C636
C644
C002

D610
C612
TP001

C605
D001 C607 W099

S809X
W048 L607

C624

S106Y
W834 W035
W839

L603
CF604
C632 C621 W038
TU001

C603

S802Y
D611
D605

OS101
R618 W068

W837
W829 C604

S104Y
C623 C606 L605
C601

C639
W039 W050 W828

L601
W819 C651 C637
W066

S105Y
CF601

More user manuals on ManualsBase.com

F-1
 F-3

More user manuals on ManualsBase.com

R813

R809
C804
R811
C805
R814
C806

R101
R816

C801

R406

R113 R126
R420 R419
R112
R131
R117
C113

C114
R111

C411
SOLDER SIDE

R505 C120
R107
R130
R504
IC101

R129
R106
R105 R115
R119 R114
PRINTED CIRCUIT BOARDS

C116 R116
R123 R128
C117
R120 R121 R110
R636 R102
R103
MAIN/CRT (CHIP MOUNTED PARTS)

R122 R124
R104

R356
R638

R646
R642

R354 R639
C616
R635 R633
C643 R620 R627
R641
33

R608
R616 R617
R634
49
17

IC601

R611
C642

R609 R631
1

R355 R358
R625
R606 C618_1 C626
R619
R630
R612 R615 R614
C699

C634_1

R605 R613
R622 R621 R602 R604
R007 R601
R603

R006 R624 R626

F-4
 A B C D E F G H

MICON/TUNER SCHEMATIC DIAGRAM

8
(MAIN PCB) 8

TU001 NJH3021U268

3 ADRES
ACCESORY

1 AGC
5 SDA
7 BPL

4 SCL
9 BTL
15

13
6 V.S
11 IF
ATC001

10

2
8
NXC0032-010010

14

12
NC

NC

NC

NC

NC
0

5.0

5.0

5.0

1.3

6.2

4.6
30.0
TP001

TM101
R25-1127 C003
FROM DEFLECTION/CRT
7 50V4.7 KA 7

6.3V 470 YK
0.022 M

HZ30-3L
P_CON+5V

D001
C004

C002
OS101 FROM POWER
PIC-28143SY-2
GND

S809X R001
1 Vout

3 GND

+B
2 B+

68K1/2W
R002

R006

R007
270

270
0
4.7
4.7

68K 1/2W FROM/TO CHROMA

AGC
IF
16V10 KA
C123

6 6
I2C_OFF
VD
R131

47

HD
MICON IC
IC101 OEC7044A 3
0 R123
4.9

42
OSD_R

1
P50/H.SYNC RED R
4.7K
0 R122
4.9

41
P51/V.SYNC GREEN G OSD_G

2
4.7K
4
0 R121
R110
0
1K

40
P00/EXT MUTE BLUE B OSD_B

3
4.7K
R116 0 R120
4.9

39
P01/I2C_OFF OSD_BLK
4
R117 OUT1/BLANK BL
5 47K 4.7K 5

R102

R103

R104

R124

4.7K
R111

2.2K

2.2K

2.2K
47K 0 0

38
P02/AUDIO MUTE P20/AV2
5
NC
10K
GND
0 0

37
P03/(Surround)
6

P21/AV1 NC SCL
SDA
0 4.9

36
P04 P22/POWER POWER
7
0.01 Y
C128

0 0 TO SOUND

35
P05/(Center_SP) P10/DEGAUSS_H
8

NC
AUDIO_MUTE
R114 4.9
4.8

34
INT2/P.FAIL
9

SCL1
10K C117
4.8 0 270P B TO POWER
10

33
INT1/REMOCON SCL2
D104 NC R105
R115
4 MTZJ6.8B 3.9 5.0 4.7K POWER 4
11

32

P23/SYNC SDA1
47K C116
FROM/TO DEFLECTION/CRT
0 0 270P B
12

31

P24 SDA2
NC NC R106 X-RAY_TEST
16.0
0 0 4.7K 0 X-RAY TEST SW X-RAY
13

30

P25/ON_TIMER AD1/X_RAY_TEST Q101

NC W812 DTC114TS
4.9 0 R107 0
14

29

AVCC X-RAY
C122 R130
10K FROM CHROMA
C121 3.0 3.2
50V 1 KA 1K
15

28

HLF AD4/AFT AFT

200P CH D101 MTZJ6.8B
C120 4.9
FROM CHROMA 0.8
16

27

V.HOLD AD5/KEY1
0.001 Y R112 D103 MTZJ6.8B
SYNC 2
C124
3 3.4 4.9 2.2K 3
17

26

Y_VIDEO CVIN AD6/KEY2 R113

R129

50V 0.1 KA
1M

AT+5V
C130 0 4.9 R119
2.2K
18

25

CNVSS RESET RESET

KA

0.01 Y
50V0.1

C125
C115

0.001 B C114 1K
1
10P CH 0.68 TF
3.7 3.6
C129
19

24

Xin OSC1
1

L101
R135

3.3uH
2.7K
2

4.2 C113
20

23

Xout OSC2
3

X101_1 4.1 10P CH

CST8.00MTW 0 4.9
21

22

VSS VCC

C119
S-24C02BDP-11

5.0 5.0 0 5.0

0.68 TF R101 R126
2 5 6 7 8 2
C118
MODE
SDA

VCC
SCL

560 2.7K R128

MEMORY IC

6.3V 470 YK
560
SKHVBED010

SKHVBED010

SKHVBED010

SKHVBED010
SKHVBED010

CH DOWN
25" VOL DOWN

VOL UP
SW103
POWER
SW105

SW102

SW101
SW104

CH UP
VSS

E0
E2

E1

IC199

4 3 2 1
25"

25"

25"

25"
0 0 0 0

NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT CAUTION: DIGITAL TRANSISTOR TUNER VIDEO SIGNAL
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
1 WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES R.SIGNAL 1
PCB010
DANS LA NOMENCLATURE DES PIECES G.SIGNAL TMX456
B.SIGNAL
DEFLECTION SIGNAL

A B C D E F G H
G-1 G-2
More user manuals on ManualsBase.com
 A B C D E F G H

CHROMA SCHEMATIC DIAGRAM

8 8
(MAIN PCB)
TO MICON/TUNER
SYNC

Y_VIDEO

AT+5V 6
4.8 10.6
FROM POWER
REG. 5.5
Q603 8.2 15.0
7 2SD734 P_CON+15V 7
S802Y S802X
RESET 7 REG.
8.8 Q606
2SD734

C622 0.015 M
CF604

50V 1 KA
10V 47 KA
EFCT4R5MW5

120 1/4W

15uH

KA
L607

50V 1 KA

C619_1
R623

C625
100
10V100 YK

C627
470P B

50V 3.3
R636
C631

C644

33K
FROM POWER

R633
W828

R622

R635
C635

8.2K
120
AT+15V
R615

C614 0.01 Y

0.01 Y

R639 100
CF603

3.579545MHz 15P CH
0.001 Y

C616
C643
EFCT4R5YS5A 470

0.01 Y
R647

1.8K
W839

C636
R638 6.8K

C630
D607
C661 0.01 Y
6 6

X602
1SS133
R646 12K

W805
2.9 2.3 0 8.2 8.2 3.9 4.8 5.5 3.4 0 NC 0 0 2.9 3.3 2.0 8.8
TO SOUND 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
C638

CHROMA APC FILTER

VIDEO/CHROMA GND
MCU RESET
INTELLIGENT MONI

Y SW OUT
5.7V REG OUT(FOR CPU)
R634 10K

5v REG
2.3

Hi Vcc

TV/Y IN
49

32
GND 3.5 50V4.7 NA
5 R611 10K
R612 R642 D605
3.0 2.6

50

31
AUDIO_OUT
5.6K C604 50V 1 KA 100K 11E1-EIC
2.3 0

51

30
AUDIO BYPASS R IN
C642 0.001 Y
3.2 5.0

52

29
EXT AUDIO IN V PULSE OUT
C623 0.0033 M
3.8 G OUT 0

53

28
FM DIRECT OUT
46 SW REG CONT 34 EXT C in
120 1/2W

C632 50V 2.2 KA

R632

3.1 47 LIMITER IN 33 8.7V REG OUT 0

VIF VCO F/B

54

27
FAST BLK
R618 10M1/4W 48 IF AGC 32 X’TAL
5 C610 5
9.2 49 QIF OUT 31 ACL/ABCL 7.3

55

26
VREG Vcc SPOT KILLER
50 AUDIO OUT
MTZJ8.2B

50V 0.22 YK
C645
D602

3.0 0

56

25
VIF APC FILTER fsc OUT
NC
470 50V 0.47 KA
10V 2200 YK
C605

2.6 5.0 16V 47 YK

C624

57

24
VIF VIDEO OUT
C618_1

22P CH

D614 FROM/TO DEFLECTION/CRT

1SS133
D601

0 5.0 MTZJ6.2B
58

23
VIF GND VIDEO CHROMA Vcc
R609

S106Y 0 C613_1 ABCL

5.6
59

22
C621 0.01 B V RAMP CAP 1 TF
P_CON+5V
2.5 R641
3.2
60

21
AFT OUT V RAMP FEEDBACK V_FEEDBACK
W819 20K
C626 2.9 64 VIF IN 17 V OUT
0
61

20
QIF IN 1 VIF IN 16 B OUT B IN
0.001 Y D615 MTZJ6.2B
R606 1.8 8.2
4 4
62

19
POWER ON CONT
RF AGC OUT STRAT UP Vcc C654 0.022 F
10K C606

INV FBP OUT

2.9 RF AGC FILTER 8.2

AFC FILTER
63

18
H VCO F/B

SAW FILTER
VIF Vcc

H OUT
50V 0.1 KA

R OUT

G OUT
CF601 R644
FBP IN
1.8 4.5
SCL
64

17
DEF
SAF45MFY220ZR

SDA
CHROMA IC V_OUT
IC601 100 1/4W
10

10V470 YK
5 4 3 2 M61203BFP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D616

C612
1.5 5.0 5.0 2.7 4.9 6.2 6.2 0 0 4.9 3.5 4.9 4.9 4.0 4.0 4.8
C634_1
0.01 B

W837
MTZJ6.2B
R626 10K

GND
0.01 Y
L605

R621

C639

11 12 13
1uH

2.7K

R601

2.7K

9
H_OUT
H_SYNC
R624 2K

MTZJ12B
R627 100
0.01 Y
10uH
L603

D611
C637

B.OUT
50V 1 KA

3 3
C603

FROM/TO MICON/TUNER L601 R630 100

G.OUT
0.01 Y
C640 16V47 YK

MTZJ12B
R631 100 TEST POINT
C601

R602
R613

100

1K

1.2uH
0.01 Y

R.OUT
470P B

R604 100
C651

AFT
2.2K

2.2K

2.2K
R617 2.7K
6.3V 470 YK

C699

MTZJ12B
CP601
R603

CLAMP
1.5K

C607

AGC

D612
CUT OFF TKC-M06X-A1

R608
R605

2.7K
Q608
4.7K

R614

R619

R625
IF
D610

2SA1015Y 0.8 B.OUT 6

D603 D604
INT.MONI 5
GND 0.1
1SS133 1SS133
0 IIC_OFF 4

50V10 KA
R620
C609
SDA 3

R616

1K
330
HD SCL 2
POWER GND 1
OSD_B
2 OSD_BLK 2
OSD_G
VD
OSD_R
I2C_OFF
SDA
SCL

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED DEFLECTION SIGNAL R.SIGNAL
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST AUDIO SIGNAL G.SIGNAL PCB010
1 WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. 1
TMX456
LUMINANCE SIGNAL B.SIGNAL
TUNER VIDEO SIGNAL

A B C D E F G H
G-3 G-4
More user manuals on ManualsBase.com
 A B C D E F G H

DEFLECTION/CRT SCHEMATIC DIAGRAM (MAIN PCB)

CD802
8 2E054401 8
FROM/TO CHROMA GND GND
GND 5 5 GND
CLAMP CLAMP
CLAMP CLAMP 4 4 CLAMP
G.OUT G.OUT
G.OUT G.OUT 3 3 G.OUT
B.OUT B.OUT
B.OUT B.OUT 2 2 B.OUT
R.OUT R.OUT
R.OUT R.OUT 1 1 R.OUT
V-OUT IC
V_OUT IC401 LA78041 CP802A CP802B
V_FEEDBACK 51048-0510 51048-0510
HS401
THERMAL PUMP L802
763WAA0119 HF57T18.5*10*10
PROTECTION UP
CD801_1 CP801_1
AMP-
8M82025A TS-80P-02-V1
+
7 VCC 1 1 7
W831
1 2 3 4 5 6 7 2 2

560P W

680P W
560P W
4.5 25.1 27.0 0 53.0 52.0 4.4

35V100 MHE

C806

C805
C804
C414
W817

14

R809

R814

R811
330

330
330
18
3.2 3.2 3.2
D403
V801 100.6 2.7 98.4 2.7 95.4 2.7
11E1-EIC
19
A63AHC26X
RED OUT GREEN OUT BLUE OUT
R418

470 1/2W

470 1/2W
TF
9 Q801 Q803 Q802

TF

100V0.068
100V 0.15
C422
2SC4075-YAC 2SC4075-YAC 2SC4075-YAC

C430
R410

R412
10
22K +-1% R

R813

R816

R815
8

4.7K

4.7K

4.7K
R420 G CC004
6
6 B 6
11

R419

25V 2200 MHE

150P SL
6.8K

1.5K
CC002

C411

11K +-1%
5 7 1

1 1/2W
R417

C418

R416
C417_1
1 TF
CC006

50V10 MHE
R407_2
DY801

1 1W
7M062505

C427
TO DY
TP022 TP023 TP024
S803X
4 4
3 3
R406

R404
3.3K

2.7K 1/4W 2 2 20 22 21
X-RAY TEST SW. MG801
R405 Q403 1 1 29MMSTAR
5 18K 1/4W 16.0 DTA144ES 5
R401 +-1%
18K +-1%

2.7K 1/4W

2.7K 1/4W

2.7K 1/4W
12K 2W
9.6 16.1 CP401_1
R408

12K 2W

12K 2W
R802
R803

R807

R805
R806

R804
HZ27-1L

100K 1/4W TS-80P-04-V1

D401

+-1% C434
FROM/TO MICON/TUNER
D402 R424 R409 100V 22 YK
K001
X-RAY 8115529
HZ11B1L 12K +-1% 6.2K +-1%
X-RAY_TEST

AU02A-EIC
D411
P_CON+5V
K002
15
C439 8115529

100uH 0607
L801
500V 22P SL

250V 0.56 ECWF

500V 470P B

K003
8115529
C440

C437
FROM/TO CHROMA H.DRIVE

330P B
R429_1

C801
Q402
GND 2SC2621
4 FB401
1.8 2W 4
ABCL 27.0 17.7 0 W897 3225010F R B G
5

17
H_OUT 0 130.0 COL
4

0.3 H.OUTPUT 1 HV
1.6KV 0.01 ECWH

H_SYNC 45.7 -0.1

0 Q401
3

2
4.7K 1/2W

P_CON+5V 2SD2499(LBOEC1) 130.0

2KV 220P BP
R446

T401_1
0
C443

5013001 D410 FOCUS

C444
100 1/4W

135.0 VIDEO F
16 6
R427

0 AU02A-EIC
SCREEN
B+ S 1
135.0
2 CP806
MTZJ6.2B

W891 GND 0
11 005P-2100
D405

P.CON+5V REG IC L406 18uH -1.9 AFC

9
IC402 KIA7805API C416 R428_1 HEA ABL 1.7
0 7
8.2 2W 10 TER
200V 0.018 PP R422
0 GND W838
8
3 6.8K 1/2W 3
1.5 E12
C401 4 GND
C446 C404 8 NC
2.0 E25
IN GND OUT 500V 22PSL 3
160V 1 MHE 10V 470 YK E8 0.8
5
1 2 3
7.8 0 5.0
R448_1 D408
W823 W824

2KV 0.001 B
10V 470 YK

AU02A-EIC
3.3K 5W D407

C802_1
C412

35V 470 YK
TO SOUND AU02A-EIC 96.4
6.4
C433
NC

11
10

12
P_CON+5V C448 0

9
SOUND+B R443_1
100K 1/4W

D422 R445_1
R421_1

100V 22 YK

F
8
101.6
4.7 2W AU02A-EIC 100K 1/4W

1
7
2 2
100V 0.1 TF

6
C435

FROM/TO POWER

5
HEATER HEATER HEATER 99.6
4 4 J801

W806
0

W802
GND GND GND CVT3275-5102
+B 3 3
GND GND GND
GND 2 2
16V470 YK

180V 180V 180V

1 1
C405

CP803A CD803 CP803B

D404 2E044101
51052-0400 51052-0400
FBT+12V
AU02A-EIC
PCB110
TCX315
PCB010
TMX456

1 R.SIGNAL CAUTION: DIGITAL TRANSISTOR 1

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT G.SIGNAL
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES B.SIGNAL
DANS LA NOMENCLATURE DES PIECES DEFLECTION SIGNAL
A B C D E F G H
G-5 G-6
More user manuals on ManualsBase.com
 A B C D E F G H

8
POWER SCHEMATIC DIAGRAM 8

(MAIN PCB)

CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE 6.3A 125V (F501)
FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES
6.3A 125V
D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 6.3A 125V (F501).
7 7

DEGAUSS COIL
R502 L502
8R250009
1.2 7W
R640 2

2
D609
1

1
EM1C-EIC 2.2K 10W
CP502
POWER REG.IC C647 R655 TV-50P-02-A1
IC501 STR30110
6 500V 0.001 B 2.2K 10W D501 D502 6

0.001 B 0.001 B
RM11C-EIC RM11C-EIC

C503

500V
MS501
23MICA

C504

500V
RY101 D504 D503
1 2 3 4 5 ALKS321 3 1
RM11C-EIC RM11C-EIC TH501
0 137.3 179.6 136.6 6.9

4
P H PTAD14K2-3R0Q141
2
TP501
D125

3
POWER
HS501 Q501 1SS133

18K +-1%
10K 1/2W
763WAA0112
330K 1/4W
2SC1815Y

R509
0
R503

R508
R504 R177
0.7 D126

1
5 W818 4.7K 5
R506 0 EM1C-EIC 1.2K 10W

R505

68K
NC

4
AC120V_60HZ
C133
6.3A 125V CD501

2
180 20W 0R614909
47 1/4W

500V 0.001 B 6.3A 125V

R507_1

L501
F501
160V 100 MHE
9-000074 BLACK

1
FH502 FH501
C507

23706.3
C501 EYF-52BC EYF-52BC WHITE

2
160V 10 MHE

BLADE
WIDE
250V 0.22 ECQUL
C519

D617 CP501
R515 THL-P03P-B1
11E1-EIC

1M 1/2W
R501_1

+-10%
200V 680 MXR
1.5 3W C646

C506_1
C132_1
25V 2200 YK
4 D608 R643 4
25V 2200 MHE
S803Y RD15FB 33 1/2W

FBT+12V S106X
D127
+B
11E1-EIC W801 W815
GND

FROM/TO MICON/TUNER

FROM/TO DEFLECTION/CRT
GND
+B
3 POWER 3

TO CHROMA

P_CON+15V
AT+15V

2 2

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
1 DANS LA NOMENCLATURE DES PIECES PCB010 1
TMX456

A B C D E F G H
G-7 G-8
More user manuals on ManualsBase.com
 A B C D E F G H

8 SOUND SCHEMATIC DIAGRAM 8

FROM MICON/TUNER

(MAIN PCB)
AUDIO_MUTE

7 FROM CHROMA 7
AUDIO_OUT

GND

6 6

5 5

FROM DEFLECTION/CRT

P_CON+5V SPEAKER
SP351_2
CP351_1 SA04A05AWA
SOUND+B TID-X02P-B2
SOUND IC
1 1
IC351_1 AN7523
2 2 SPEAKER
4 SP351_2 4

R355

3.9K
SA04A05AWA
+ - + -
120K
R356

+ -

VCC GND
1 2 3 4 5 6 7 8 9
5.7 4.6 0 4.6 4.1 1.6 0 NC 0 2.9

W834
50V 1 MHE
10V 3300 YK

24
C352

R358

5.6K
C351

0.0033 M
C359_1

W820
3 3
S801Y
50V 2.2 KA

S809Y S801X
C353_1
W835

W829
23
W813
W810

2.9 MUTE SW.

R354
2 Q351 2
2SC1815Y
47K 0
0
50V 10 KA
C357_1

W814

PCB010
1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT AUDIO SIGNAL TMX456 1
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-9 G-10
More user manuals on ManualsBase.com
 WAVEFORMS
MICON/TUNER

1 200mV 5ms/div 6 0.5V 20µs/div 11 1V 20µs/div

2 0.5V 20µs/div 7 200mV 20µs/div 12 1V 20µs/div

3 200mV 20µs/div 8 20V 20µs/div 13 1V 20µs/div

DEFLECTION/CRT

4 200mV 5ms/div 9 200mV 20µs/div 14 0.5V 5ms/div

CHROMA

5 0.5V 2ms/div 10 0.5V 5ms/div 15 20V 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1

More user manuals on ManualsBase.com

 WAVEFORMS

16 2V 20µs/div 21 50V 20µs/div

17 200V 20µs/div 22 50V 20µs/div

SOUND

18 10V 5ms/div 23 0.5V 1ms/div

19 10V 5ms/div 24 1V 1ms/div

20 50V 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2

More user manuals on ManualsBase.com

 MECHANICAL EXPLODED VIEW
111
204

204
204

204
204
113

J801
205 204
119

204
110

116
205
105 119

PCB110
114
(CRT PCB)

205 L502 203

FB401 101

205 202
102 MS501 202
103
115 V801

115 104 ATC001

112
203 TU001

203
SP351 PCB010
201
(MAIN PCB)

201

117
108
201 109
118

107

120
106

I-1

More user manuals on ManualsBase.com

 MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION
101 8995034000 CORD CLIP UL CO.
102 --- HEAT SINK
103 --- HEAT SINK
104 --- METAL SPACER
105 741WUA0021 SPRING,EARTH
106 701APJA036 CABINET,FRONT
107 713WPA0096 GUIDE,REMOCON
108 7230006856 SHEET,CAUTION
109 735WPA0426 BUTTON ASS'Y

110 702APA0086 CABINET,BACK

111 722552A004 SHEET,RATING
112 723000B179 FILM,DECORATION
113 7232020733 SHEET,BRAND
114 899HV3T001 HOLDER,ANODE WIRE
115 762WPA0009 HOLDER,CRT WIRE
116 8994201000 HOLDER,CRT WIRE
117 7220001109 SHEET,HWC
118 7240001041 SHEET,CSA WARNING
119 --- COATING CLIP

120 A3I062G720 CABINET,FRONT ASS'Y

201 8110630A04 SCREW,TAP TITE (P) BRAZIER 3x10

202 8117D30A04 SCREW,TAPPING (B0) WH8 BRAZIER 3x10
203 8109630802 SCREW,TAP TITE (B) BRAZIER 3x8
204 8117540B04 SCREW,TAPPING (B0) TRUSS 4x20
205 8111J50D04 SCREW,TAPPING (A) GW22 5x40

--- J3I06201 INSTRUCTION BOOK

--- JB5U0100 POLYBAG
--- 792AHA0073 PACKAGE,TOP
--- 792AHA0074 PACKAGE,BOTTOM
--- 791AHA0021 FILM BAG
--- 793ACDA087 GIFT BOX

J1-1

More user manuals on ManualsBase.com

 ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION
RESISTORS DIODES
R135 R001T6272J RC 2.7K OHM 1/6W D604 D1VT001330 DIODE, SILICON 1SS133T-77
! R177 R5W2CF122J R, CEMENT 1.2K OHM 10W D605 D2WT011E10 DIODE, SILICON 11E1-EIC
! R401 R4X5T4104F R, METAL 100K OHM 1/4W D607 D1VT001330 DIODE, SILICON 1SS133T-77
! R404 R002T4272J RC 2.7K OHM 1/4W D608 D9201150B1 DIODE, ZENER RD15FB
! R405 R4X5T4183F R, METAL 18K OHM 1/4W D609 D2WT0EM1C0 DIODE, SILICON EM1C-EIC
! R406 R903N8332J RC 3.3K OHM 1/8W D610 D97U01201B DIODE, ZENER MTZJ12B T-77
! R407 R65581010J R, FUSE 1 OHM 1W D611 D97U01201B DIODE, ZENER MTZJ12B T-77
! R408 R4X5T6183F R, METAL 18K OHM 1/6W D612 D97U01201B DIODE, ZENER MTZJ12B T-77
! R409 R4X5T6622F R, METAL 6.2K OHM 1/6W D614 D97U06R21B DIODE, ZENER MTZJ6.2B T-77
R417 R4X5T6113F R, METAL 11K OHM 1/6W D615 D97U06R21B DIODE, ZENER MTZJ6.2B T-77
R418 R4X5T6223F R, METAL 22K OHM 1/6W D616 D97U06R21B DIODE, ZENER MTZJ6.2B T-77
! R424 R4X5T6123F R, METAL 12K OHM 1/6W D617 D2WT011E10 DIODE, SILICON 11E1-EIC
! R428 R3X28A8R2J R, METAL 8.2 OHM 2W ICS
! R429 R6558A1R8J R, FUSE 1.8 OHM 2W IC101 I56F07044A IC OEC7044A
R430 R00106104J RC 100K OHM 1/6W IC199 A3I051G015 IC S-24C02BDP-1A
! R443 R6558A4R7J R, FUSE 4.7 OHM 2W ! IC351 I0FSP75230 IC AN7523
! R448 R5X2CD332J R, CEMENT 3.3K OHM 5W ! IC401 I03TD80410 IC LA78041
R501 R21202105K R, SOLID 1M OHM 1/2W ! IC402 I1KA97805A IC KIA7805API
! R502 R5X2CE1R2J R, CEMENT 1.2 OHM 7W ! IC501 I2B4901100 IC STR30110
R506 R5W2CH181J R, CEMENT 180 OHM 20W IC601 I06FC12030 IC M61203BFP
! R507 R655U4470J R, FUSE 47 OHM 1/4W TRANSISTORS
! R509 R4X5T6183F R, METAL 18K OHM 1/6W Q101 TNYTJ03001 COMPOUND TRANSISTOR DTC114TSTP
! R515 R3X28B1R5J R, METAL 1.5 OHM 3W Q351 TC5T018154 TRANSISTOR, SILICON 2SC1815Y(TPE2)
! R640 R5X2CF222J R, CEMENT 2.2K OHM 10W ! Q401 TDUU024990 TRANSISTOR, SILICON 2SD2499(LBOEC1)
R647 R00106182J RC 1.8K OHM 1/6W ! Q402 TC3Q026210 TRANSISTOR, SILICON 2SC2621(D,E)-RAC
! R655 R5X2CF222J R, CEMENT 2.2K OHM 10W Q403 TPYTD03001 COMPOUND TRANSISTOR DTA144ESTP
! R803 R3X18A123J R, METAL OXIDE 12K OHM 2W Q501 TC5T018154 TRANSISTOR, SILICON 2SC1815Y(TPE2)
! R805 R3X18A123J R, METAL OXIDE 12K OHM 2W Q603 TD3T007340 TRANSISTOR, SILICON 2SD734(E,F)-AA
! R807 R3X18A123J R, METAL OXIDE 12K OHM 2W Q606 TD3T007340 TRANSISTOR, SILICON 2SD734(E,F)-AA
CAPACITORS Q608 TA5T010154 TRANSISTOR, SILICON 2SA1015Y(TPE2)
C132 E5EZF3222M CE 2200 UF 25V ! Q801 TC3Q040750 TRANSISTOR, SILICON 2SC4075-YAC
C351 E02LF1332M CE 3300 UF 10V ! Q802 TC3Q040750 TRANSISTOR, SILICON 2SC4075-YAC
! C404 E02LT1471M CE 470 UF 10V ! Q803 TC3Q040750 TRANSISTOR, SILICON 2SC4075-YAC
! C405 E02LT2471M CE 470 UF 16V COILS &TRANSFORMERS
! C412 E02LT1471M CE 470 UF 10V L101 021LA63R3K COIL 3.3 UH
! C414 E5EZT4101M CE 100 UF 35V L406 021U6D180K COIL 18 UH
C416 P3N1F2183J CPP 0.018 UF 200V ! L501 029K000074 COIL, LINE FILTER 9-000074
! C418 E5EZF3222M CE 2200 UF 25V ! L502 028R250009 COIL, DEGAUSS 8R250009
! C433 E02LT4471M CE 470 UF 35V L601 0216731R2K COIL 1.2 UH
! C434 E02LT8220M CE 22 UF 100V L603 021673100K COIL 10 UH
C437 P411F3564J CMPP 0.56 UF 250V ECWF L605 0216731R0J COIL 1 UH
! C443 P414F9103H CMPP 0.01 UF 1.6KV ECWH L607 021LA6150K COIL 15 UH
! C444 C01BBP7H2K CC 220 PF 2KV BP L801 02167D101K COIL 100 UH
! C446 E5EZTB010M CE 1UF 160V L802 02A6A8A0A1 CORE, FERRITE HF57T18.5*10*10
! C448 E02LT8220M CE 22 UF 100V T401 045013001J TRANS, HORIZONTAL DRIVE 5013001
! C501 P2122B224M CMP 0.22 UF 250V ECQUL JACK
! C506 E52SFC681M CE 680 UF 200V ! J801 066C130015 SOCKET, CRT CVT3275-5102
! C507 E5EZFB101M CE 100 UF 160V SWITCHES
! C519 E5EZTB100M CE 10UF 160V SW101 0504201T31 SWITCH, TACT SKHVBED010 or
C624 E02L01222M CE 2200 UF 10V 0504101T34 SWITCH, TACT EVQ21505R
C646 E02LF3222M CE 2200 UF 25V SW102 0504201T31 SWITCH, TACT SKHVBED010 or
C699 CHGTY0214M CC 0.01 UF 16V Y 0504101T34 SWITCH, TACT EVQ21505R
DIODES SW103 0504201T31 SWITCH, TACT SKHVBED010 or
D001 D94TA30013 DIODE, ZENER HZ30-3L TD 0504101T34 SWITCH, TACT EVQ21505R
D101 D97U06R81B DIODE, ZENER MTZJ6.8B T-77 SW104 0504201T31 SWITCH, TACT SKHVBED010 or
D103 D97U06R81B DIODE, ZENER MTZJ6.8B T-77 0504101T34 SWITCH, TACT EVQ21505R
D104 D97U06R81B DIODE, ZENER MTZJ6.8B T-77 SW105 0504201T31 SWITCH, TACT SKHVBED010 or
D125 D1VT001330 DIODE, SILICON 1SS133T-77 0504101T34 SWITCH, TACT EVQ21505R
! D126 D2WT0EM1C0 DIODE, SILICON EM1C-EIC P.C.BOARD ASSEMBLIES
D127 D2WT011E10 DIODE, SILICON 11E1-EIC PCB010 A3I058G01A PCB ASS'Y TMX456A
! D401 D94TA27011 DIODE, ZENER HZ27-1L TD PCB110 A3I057G11A PCB ASS'Y TCX315A
! D402 D94TA11B11 DIODE, ZENER HZ11B1L TD MISCELLANEOUS
D403 D2WT011E10 DIODE, SILICON 11E1-EIC ! ATC001 0632400008 ANT, UNIT NXC0032-010010
! D404 D2WTAU02A0 DIODE, SILICON AU02A-EIC ! CD501 120R614909 CORD, AC 0R614909 or
D405 D97U06R21B DIODE, ZENER MTZJ6.2B T-77 1207614909 CORD, AC 7614909
! D407 D2WTAU02A0 DIODE, SILICON AU02A-EIC CD801 068M82025A CORD, CONNECTOR 8M82025A
! D408 D2WTAU02A0 DIODE, SILICON AU02A-EIC CD802 122E054401 CORD, JUMPER 122E054401
! D410 D2WTAU02A0 DIODE, SILICON AU02A-EIC CD803 122E044101 CORD, JUMPER 122E044101
! D411 D2WTAU02A0 DIODE, SILICON AU02A-EIC CF601 1022T45R72 FILTER, SAW SAF45MFY220ZR
! D422 D2WTAU02A0 DIODE, SILICON AU02A-EIC CF603 1011T4R504 FILTER, CERAMIC EFCT4R5YS5A
! D501 D2WTRM11C0 DOIDE, SILICON RM11C-EIC CF604 1011T4R517 FILTER, CERAMIC EFCT4R5MW5
! D502 D2WTRM11C0 DOIDE, SILICON RM11C-EIC CP351 069W120019 CONNECTOR PCB SIDE TID-X02P-B2
! D503 D2WTRM11C0 DOIDE, SILICON RM11C-EIC ! CP401 069W340018 CONNECTOR PCB SIDE TS-80P-04-V1
! D504 D2WTRM11C0 DOIDE, SILICON RM11C-EIC ! CP501 0697320039 CORD, UX CONNECTOR THL-P03P-B1
D601 D1VT001330 DIODE, SILICON 1SS133T-77 ! CP502 069W420029 CONNECTOR PCB SIDE TV-50P-02-A1
D602 D97U08R21B DIODE, ZENER MTZJ8.2B T-77 CP601 0697260650 CONNECTOR PCB SIDE TKC-M06X-A1
D603 D1VT001330 DIODE, SILICON 1SS133T-77 CP801 069W320018 CONNECTOR PCB SIDE TS-80P-02-V1

J2-1

More user manuals on ManualsBase.com

 ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION
MISCELLANEOUS
CP806 069W010010 CONNECTOR PCB SIDE 005P-2100
CP802A 067R005019 WIRE HOLDER 51048-0510
CP802B 067R005019 WIRE HOLDER 51048-0510
CP803A 067R104019 WIRE HOLDER 51052-0400
CP803B 067R104019 WIRE HOLDER 51052-0400
! DY801 027M062505 DY 7M062505
! F501 081PA6R302 FUSE 23706.3
! FB401 043225010F TRANSFORMER, FLYBACK 3225010F
FH501 06710T0006 HOLDER, FUSE EYF-52BC
FH502 06710T0006 HOLDER, FUSE EYF-52BC
! K001 129A000010 WEDGE 8115529
! K002 129A000010 WEDGE 8115529
! K003 129A000010 WEDGE 8115529
MG801 026A062704 MAGNET, CONVERGENCE 29MMSTAR
MS501 128B000018 SHEET 23MICA
OS101 077Q014003 REMOTE RECEIVER PIC-28143SY-2
! RY101 0560V20115 RELAY ALKS321
! SP351 070C533016 SPEAKER SA04A05AWA
! TH501 DF40A3R0Q0 DEGAUSS, ELEMENT PTAD14K2-3R0Q141
TM101 076R074180 TRANSMITTER R25-1127
! TU001 0145W00049 TUNER, VHF-UHF NJH3021U268
! V801 0984250502 COLOR, PICTURE TUBE A63AHC26X
X101 1002T00801 CERAMIC OSILLATOR 8MHz
X602 100CT3R505 CRYSTAL HC-49/C 3.579545MHz

RESISTOR
RC................... CARBON RESISTOR

CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................. METAL POLYESTER CAPACITOR
CMPL............... METAL PLASTIC CAPACITOR
CMPP.............. METAL POLYPROPYLENE CAPACITOR

J2-2

More user manuals on ManualsBase.com

SPEC.NO. M3I0-62G
O/R NO. A063519