Absorber Packing Drawings

6 5 4 3 2 1
G E N E R A L N O T E S
N10A N2 N10A N2 KOCH-GLITSCH PROVIDES THIS DRAWING SOLELY FOR BUYER'S CONVENIENCE IN DESIGNING AND FABRICATING
PARTS TO MATCH EQUIPMENT FURNISHED BY KOCH-GLITSCH. BUYER IS SOLELY RESPONSIBLE FOR PROVIDING
CORROSION AND OTHER ALLOWANCES THAT MAY BE REQUIRED FOR SPECIFIC PROCESS OR MECHANICAL
CONSIDERATIONS WHETHER OR NOT SUCH PROCESSES OR CONSIDERATIONS HAVE BEEN COMMUNICATED TO
KOCH-GLITSCH.
75
75
1 ELEVATION AND ORIENTATION PICTURES ARE SCHEMATIC REPRESENTATIONS OF EQUIPMENT AND DO NOT
TAN LINE TAN LINE INDICATE THE ACTUAL DESIGNS. SEE EQUIPMENT DRAWINGS FOR ACTUAL DESIGNS.
WELD LINE E.L. +7465 WELD LINE E.L. +7465 THE CUSTOMER SHOULD TAKE CORRECTIVE ACTION TO ELIMINATE SOLIDS ACCUMULATION IN THE PROCESS.
311
248
247
D 1 DEMISTER® MIST ELIMINATOR 1 PARALLEL FILTERS ARE RECOMMENDED IN ALL EXTERNAL FEED AND REFLUX LINES TO PROTECT AGAINST
DISTRIBUTOR BLOCKAGE. KOCH-GLITSCH SUGGESTS FILTERS CAPABLE OF REMOVING PARTICLES 1/4 THE SIZE
D
DWG. NO. KG00112636-003
OF THE MINIMUM FEED HOLE SIZE, BUT ASSUMES NO RESPONSIBILITY FOR RECOMMENDING OR DESIGNING
E.L. +7217
590
BOTTOM MISTEX
N FILTERS. SHOULD SOLID ACCUMULATION IMPAIR THE PERFORMANCE OF THE DISTRIBUTOR(S) KOCH-GLITSCH'S
PERFORMANCE WARRANTY WILL BECOME VOIDED. REFER TO KOCH-GLITSCH'S TERMS AND CONDITIONS
1288.6
1 1 2 CONCERNING RESPONSIBILITY FOR PROCESS CLEANLINESS.
793
SUPPORT TO BE REUSE
N12 N12
1616
E.L. +6780 E.L. +6780
1368
1 1 315° 0°
2 N11 N8 N6 N5B N5A N3 TOP
E.L. +6424 N3 E.L. +6424 N3
6
FEED PIPE DISTRIBUTOR N2
AT NOZZLE 'N3'
DWG. NO. KG00112636-004
2
EXISTING E.L. +5849 285°
N7 N9
272.4
SUPPORT RING
TO BE CUT-OFF EXISTING
10mm FROM SHELL SUPPORT RING
TO BE CUT-OFF 270° 90°
TROUGH DISTRIBUTOR 10mm FROM SHELL N4
DWG. NO. KG00112636-005
BED #1
BED #1
C FLEXIPAC® 250Y HC® HALF C

LAYER TO BE FITTED AT THE
TOP OF THE BED
2
BTM.
225°
7465 TAN LINE TO TAN LINE N10A N10B
7465 TAN LINE TO TAN LINE

4455 BED HEIGHT (+49.5 / -0)
1
4600 BED HEIGHT
180°
N12 N1
ORIENTATION OF NOZZLES
(EXISTING)
ELEVATION AND ORIENTATION PICTURES CUSTOMER NOTE:
PACKING FLEXIPAC® 250Y HC® ARE SCHEMATIC REPRESENTATIONS OF
KOCH-GLITSCH PROVIDES THIS DRAWING SOLELY FOR THE
STRUCTURED PACKING EQUIPMENT AND DO NOT INDICATE THE
BUYER'S CONVENIENCE IN DESIGNING AND FABRICATING
(16-FULL LAYER) ACTUAL DESIGNS. SEE EQUIPMENT
PARTS TO MATCH EQUIPMENT FURNISHED BY KOCH-GLITSCH.
(1-HALF LAYER) DRAWINGS FOR ACTUAL DESIGNS.
B BUYER IS SOLELY RESPONSIBLE FOR PROVIDING CORROSION
AND OTHER ALLOWANCES THAT MAY BE REQUIRED FOR
B
SPECIFIC PROCESS OR MECHANICAL CONSIDERATIONS
WHETHER OR NOT SUCH PROCESSES OR CONSIDERATIONS
HAVE BEEN COMMUNICATED TO KOCH-GLITSCH.
EXISTING
SUPPORT RING
STRUCTURED PACKING TO BE REUSE REVISED AS MARKED & CERTIFIED FINAL AS
SUPPORT GRID 2 BTP HSK GB 26 FEB 24
FABRICATED
DWG. NO. KG00112636-007 1 REVISED AS MARKED & APPROVED FOR FABRICATION BTP HSK GB 06 FEB 24
100
2 0 ORIGINAL DESIGN RLM HSK GB 21 DEC 23
REV DESCRIPTION BY CHK APP DATE
FOR PARTS & SERVICE: WWW.KOCH-GLITSCH.COM
E.L. +1167 N10B N11 E.L. +1167 N10B N11 E.L. +1294 AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500
E.L. +1223 1 This product or system may be protected by one or more patents, copyrights, trademarks, trade secrets, and other intellectual property and related
1130 1 rights.For a list of some relevant patents and trademarks, please see www.koch-glitsch.com/legal-notices
n1130 ( 1126 LINED)
6
75
By receiving this drawing, you acknowledge that this drawing and the information, and any equipment referenced herein or any information contained herein
COLUMN I.D.
COLUMN I.D. AS BUILT is proprietary and confidential information of Koch-Glitsch, LP or its respective affiliates, collectively doing business as Koch-Glitsch (KG), and shall not be
totally or partially, directly or indirectly transferred, disclosed to any person, copied, traced, photographed, reproduced in any manner, or used for any
E.L. +825 N9 N8 E.L. +825 N9 N8 2 purpose whatsoever, except: (1) for the limited purpose of, and solely to the extent necessary for, the installation, operation or maintenance of the
N1 E.L. +837 N1 E.L. +837 NOZZLE SIZE SERVICE

equipment referenced herein, or (2) by written permission of KG. The equipment referenced herein shall not be reverse-engineered. KG retain all intellectual
property rights, whether registered or unregistered, including, but not limited to trade secrets, trademarks, patents, designs and copyrights, embodied in this
drawing and the information contained herein. By accepting, receiving and/or taking possession of and/or by making use of this drawing for either of the
1294
N1 10" WET GAS INLET purposes permitted above, you are deemed to have agreed, in consideration for the supply of this drawing and/or connected information by KG, to be bound
1223
by a legal obligation to (i) keep this drawing and the information contained herein strictly confidential; (ii) solely grant access of this drawing to your
E.L. +685 N6 N7 E.L. +685 N6 N7 N10A 0.5" DIFFERENTIAL PRESSURE TRANSMITTER
employees necessarily responsible for installation, operation, or maintenance of the equipment referenced herein; (iii) prevent photocopies, photos, sketches,
video recordings or any measurements of the drawing referenced herein to be taken by your employees or any third parties; and (iv) return it to KG upon
request. Copyright 2023, Koch-Glitsch, LP
1 N10B 0.5" DIFFERENTIAL PRESSURE TRANSMITTER

N11 1" RELIEF VALVE
E.L. +380 N5A E.L. +380 N5A
75
75
N12 24" MANWAY W/ BLIND & DAVIT

WELD LINE WELD LINE
A TAN LINE TAN LINE
N2 10" DRY GAS OUTLET
Koch-Glitsch Italia SRL
A
E.L. +151 N5B E.L. +0 E.L. +151 N5B E.L. +0 N3 2" LEAN GLYCOL INLET
N4 2" RICH GLYCOL OUTLET
FOR: PAK-ARAB REFINERY LIMITED ELEVATION & ORIENTATIONS
USER: FATIMA FERTILIZER CO LTD T-100
N5A 1.5" LEVEL BRIDLE
GLYCOL ABSORBER
N5B 1.5" LEVEL BRIDLE JOBSITE: FATIMA FERTILIZER CO LTD 1130mm VESSEL I.D.
N6 0.75" TEMPARATURE TRANSMITTER MULTAN (PAKISTAN) CUSTOMER TAG: ITEM NO:
E.L. -556 N4 E.L. -556 N4 N7 0.75" TEMPARATURE GAUGE PO NO: FPO-81967 T-100 KG00112636-001
N8 0.5" PRESSURE TRANSMITTER PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 1 OF 4 REV
EXISTING ELEVATION MODIFIED ELEVATION N9 0.5" PRESSURE GAUGE ASSET NO: KG00112636 KG00112636 2
6 5 4 3 2 1
6 5 4 3 2 1
315° 315°
0° 0° N3 0°
N3
D N 45° D
45°
270° 90° 270° 90° 270° 90°
225° 225°
C C
180°
ORIENTATION OF DEMISTER® MIST ELIMINATOR
180° 180°
N12 N12
ORIENTATION OF FEED PIPE DISTRIBUTOR AT NOZZLE 'N3' ORIENTATION OF TROUGH DISTRIBUTOR
0° 0°
315° 45°
45°
B F1 B
AS BUILT
F2
SUPPORT GRID ORIENTATION CORRECTED

2 BTP HSK GB 26 FEB 24
270° 90° 270° 90° & CERTIFIED FINAL AS FABRICATED
1 APPROVED FOR FABRICATION BTP HSK GB 06 FEB 24
0 ORIGINAL DESIGN RLM HSK GB 21 DEC 23
F3 FOR PARTS & SERVICE: WWW.KOCH-GLITSCH.COM

AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500
This product or system may be protected by one or more patents, copyrights, trademarks, trade secrets, and other intellectual property and related
rights.For a list of some relevant patents and trademarks, please see www.koch-glitsch.com/legal-notices
F1 By receiving this drawing, you acknowledge that this drawing and the information, and any equipment referenced herein or any information contained herein
is proprietary and confidential information of Koch-Glitsch, LP or its respective affiliates, collectively doing business as Koch-Glitsch (KG), and shall not be
purpose whatsoever, except: (1) for the limited purpose of, and solely to the extent necessary for, the installation, operation or maintenance of the
225° drawing and the information contained herein. By accepting, receiving and/or taking possession of and/or by making use of this drawing for either of the
purposes permitted above, you are deemed to have agreed, in consideration for the supply of this drawing and/or connected information by KG, to be bound
225° 135° by a legal obligation to (i) keep this drawing and the information contained herein strictly confidential; (ii) solely grant access of this drawing to your
180° 180°
A ORIENTATION OF BOTTOM LAYER FOR ORIENTATION OF STRUCTURED PACKING SUPPORT GRID 2 Koch-Glitsch Italia SRL
A
FLEXIPAC® 250Y HC® STRUCTURED PACKING BED FOR: PAK-ARAB REFINERY LIMITED ELEVATION & ORIENTATIONS
(TOTAL-16 FULL LAYERS & ONE HALF LAYER) USER: FATIMA FERTILIZER CO LTD T-100
(ROTATE ADJACENT LAYERS 90° CW) GLYCOL ABSORBER
JOBSITE: FATIMA FERTILIZER CO LTD 1130mm VESSEL I.D.
MULTAN (PAKISTAN) CUSTOMER TAG: ITEM NO:
PO NO: FPO-81967 T-100 KG00112636-001
PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 2 OF 4 REV
ASSET NO: KG00112636 KG00112636 2
6 5 4 3 2 1
6 5 4 3 2 1
1130 TOWER I.D.(1126 LINED) 2 1130 TOWER I.D.(1126 LINED) 2
D D
142 423
REF. n105
n50
N3
CUSTOMER NOTE:
R523
BUYER'S CONVENIENCE IN DESIGNING AND FABRICATING
PARTS TO MATCH EQUIPMENT FURNISHED BY KOCH-GLITSCH.
BUYER IS SOLELY RESPONSIBLE FOR PROVIDING CORROSION
42 WIDE X 6 THK 1 AND OTHER ALLOWANCES THAT MAY BE REQUIRED FOR
SUPPORT RING SPECIFIC PROCESS OR MECHANICAL CONSIDERATIONS
C HAVE BEEN COMMUNICATED TO KOCH-GLITSCH. C
NOTES
PLAN VIEW OF SUPPORT FOR STRUCTURED PACKING SUPPORT GRID 1. TOWER MANHOLE I.D. ACTUAL: 603 mm 2
PLAN VIEW OF SUPPORT FOR FEED PIPE AT NOZZLE 'N3' 2. TOWER ATTACHMENTS ARE EXISTING OR SUPPLIED BY OTHERS UNLESS
(EXISTING TO BE REUSE) IDENTIFIED BY MARK #(E.G. 301) ENCLOSED AS SHOWN 301
(EXISTING TO BE REUSE) WHICH ARE SUPPLIED BY KOCH-GLITSCH.
3. DIMENSIONS ARE GIVEN IN: MILLIMETERS
4. ANY MODIFICATIONS BY CUSTOMER OR ANY THIRD PARTY TO THE EQUIPMENT
1130 TOWER I.D.(1126 LINED) 2 1130 TOWER I.D.(1126 LINED) 2 SHOWN ON THIS DRAWING WITHOUT THE PRIOR WRITTEN APPROVAL OF
KOCH-GLITSCH WILL VOID ANY APPLICABLE WARRANTIES.
5. ALL WARRANTIES AND VOIDANCES THERETO, ARE PER THE SELLER'S STANDARD
TERMS AND CONDITIONS OR THE NEGOTIATED TERMS SELLER HAS ACCEPTED.
6. WELD CORROSION ALLOWANCE "CA" HAS BEEN INCLUDED TO THROAT DIMENSION.
7. THE TOWER ATTACHMENTS HAVE TO BE SECURELY WELDED TO THE VESSEL
STRUCTURE AND THE CUSTOMER IS RESPONSIBLE FOR THE SELECTION OF THE
METHOD OF THE ATTACHMENT, THE WPS, AND THE EVALUATION OF ALL
SHELL APPLICABLE STRESSES.
8. CORROSION ALLOWANCE, CA = 0.0mm TOTAL.
AS BUILT
EQUIPMENT DESCRIPTION
B QUAN DESCRIPTION REMARKS B

1 SUPPORT FOR FEED PIPE AT NOZZLE 'N3' (EXISTING) AS SHOWN
1 SUPPORT FOR STRUCTURED PACKING SUPPORT GRID (EXISTING) AS SHOWN
2 PLAN VIEW OF SUPPORT RING (EXISTING) AS SHOWN
2 PLAN VIEW OF SUPPORT RING (MODIFICATION) AS SHOWN
REVISED AS MARKED & CERTIFIED FINAL AS

FABRICATED
1 REVISED AS MARKED & APPROVED FOR FABRICATION BTP HSK GB 06 FEB 24
NOTE! REV DESCRIPTION BY CHK APP DATE
SUPPORT RING
ALL PARTS SHOWN FOR PARTS & SERVICE: WWW.KOCH-GLITSCH.COM
TO BE CUT-OFF AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500
10mm FROM SHELL ON THIS SHEET WILL This product or system may be protected by one or more patents, copyrights, trademarks, trade secrets, and other intellectual property and related
BE EXISTING REUSED rights.For a list of some relevant patents and trademarks, please see www.koch-glitsch.com/legal-notices
WITH MODIFICATION. is proprietary and confidential information of Koch-Glitsch, LP or its respective affiliates, collectively doing business as Koch-Glitsch (KG), and shall not be
R523 property rights, whether registered or unregistered, including, but not limited to trade secrets, trademarks, patents, designs and copyrights, embodied in this
1 42 WIDE X 6 THK
SUPPORT RING
A Koch-Glitsch Italia SRL

A
LIST OF MATERIAL FOR: PAK-ARAB REFINERY LIMITED TOWER ATTACHMENTS
DESCRIPTION TYPE & THICKNESS
PLAN VIEW OF SUPPORT RING PLAN VIEW OF SUPPORT RING GLYCOL ABSORBER
SUPPORT RING SA 240 TP 304 - 6 THK (EXISTING) 1130mm VESSEL I.D.
(EXISTING) 1 (MODIFICATION)
JOBSITE: FATIMA FERTILIZER CO LTD
1 INT. PRO. PIPE EXISTING - AS NOTED MULTAN (PAKISTAN) CUSTOMER TAG: ITEM NO:
PLATE FLANGE EXISTING - 10 THK PO NO: FPO-81967 T-100 KG00112636-001
BOLT BAR SA 240 TP 304 - 6 THK (EXISTING) PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 3 OF 4 REV
ASSET NO: KG00112636 KG00112636 2
6 5 4 3 2 1
6 5 4 3 2 1
1130 TOWER I.D.(1126 LINED) 2

ASSEMBLY 9500A
1 M12 HEX NUT (EXISTING)

2 WASHER 25 OD. (EXISTING)
1 M12 X 35 BOLT (EXISTING)
D D
NOTE!
ALL PARTS SHOWN
ON THIS SHEET WILL
BE EXISTING REUSE
C C
CUSTOMER TO CONFIRM
320
ALL DIMENSIONS
R523
42 WIDE x 6 THK.
SUPPORT RING
CUSTOMER NOTE:
25 BUYER'S CONVENIENCE IN DESIGNING AND FABRICATING
363.5 PARTS TO MATCH EQUIPMENT FURNISHED BY KOCH-GLITSCH.
BUYER IS SOLELY RESPONSIBLE FOR PROVIDING CORROSION
AND OTHER ALLOWANCES THAT MAY BE REQUIRED FOR
SPECIFIC PROCESS OR MECHANICAL CONSIDERATIONS
HAVE BEEN COMMUNICATED TO KOCH-GLITSCH.
AS BUILT
B QUAN DESCRIPTION REMARKS
B
PLAN VIEW OF SUPPORT FOR "A4" 1 SUPPORT FOR DEMISTER® MIST ELIMINATOR (EXISTING) AS SHOWN
"A4" DEMISTER® MIST ELIMINATOR 1
EXISTING TO BE REUSE
REVISED AS MARKED & CERTIFIED FINAL AS
FABRICATED
1 REVISED AS MARKED & APPROVED FOR FABRICATION BTP HSK GB 06 FEB 24
363.5 363.5
25

50

311
THK.
60 60 request. Copyright 2023, Koch-Glitsch, LP
THK.
6
6
270 590 269.9

A
60
LIST OF MATERIAL FOR: PAK-ARAB REFINERY LIMITED TOWER ATTACHMENTS

25
DESCRIPTION TYPE & THICKNESS

9500A GLYCOL ABSORBER
1 SUPPORT RING SA 240 TP 304 - 6 THK (EXISTING)
4 JOBSITE: FATIMA FERTILIZER CO LTD 1130mm VESSEL I.D.
"D4" SUPPORT ANGLE
SUPPORT ANGLE SA 240 TP 304 - 6 THK (EXISTING) MULTAN (PAKISTAN) CUSTOMER TAG: ITEM NO:
VIEW "A4"-"A4" DETAIL "D4" NUT SA 193 GR 2H - AS NOTED (EXISTING) PO NO: FPO-81967 T-100 KG00112636-001
BOLT SA 193 GR B7 - AS NOTED (EXISTING) PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 4 OF 4 REV
HARDWARE F 436 - AS NOTED (EXISTING) ASSET NO: KG00112636 KG00112636 2
6 5 4 3 2 1
6 5 4 3 2 1
2 APPROXIMATE WEIGHT OF STRUCTURED PACKING SUPPORT GRID 35 Kg

701 3302A
ASSEMBLY 3302A
2 8
1 M10 HEX NUT 891- 340F 03
1 WASHER 25 OD. 800- 340G 020801
1 M10 X 25 BOLT 896- 340F 1305
700
1
D D
1 2
N O T E S
1. VESSEL MANHOLE I.D. ACTUAL: 603mm
2. PARTS SUPPLIED BY KOCH-GLITSCH ARE IDENTIFIED BY
MARK # (EG. 001-301).
3. ITEMS & HARDWARE ASSEMBLIES FURNISHED
ARE REPRESENTED AS THUS:
ITEM OR ASSEMBLY NO.
QUANTITY PER ASSEMBLY SHOWN 301
1
4. SPARE HARDWARE IS PROVIDED AS QUOTED, BUT

NOT ADDED TO THE PART LIST QUANTITY.
5. "-" ON PARTS LIST INDICATES SHOP WELDED PARTS.
C 7. ANY MODIFICATIONS BY CUSTOMER OR ANY THIRD PARTY C
TO THE EQUIPMENT SHOWN ON THIS DRAWING WITHOUT
THE PRIOR WRITTEN APPROVAL OF KOCH-GLITSCH WILL
VOID ALL EXPRESSED AND IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR PURPOSE.
8. ALL WARRANTIES AND VOIDANCES THERETO, ARE PER THE
SELLER'S STANDARD TERMS AND CONDITIONS OR THE
NEGOTIATED TERMS SELLER HAS ACCEPTED.
9. SPARE: BOLT & NUT - 10%, HARDWARE - 5%.
REFERENCE DRAWING:
DRAWING KG00112636 FOR VESSEL ELEVATION & ORIENTATIONS.
QUAN DESCRIPTION REMARKS
1 ISOMETRIC VIEW OF STRUCTURED PACKING SUPPORT GRID AS SHOWN
B B
GENERAL TOLERANCE LEGEND (UNLESS NOTED OTHERWISE)
SHEET METAL (FLAT): ±0.125"/3mm SAWING: ±0.125"/3mm
SHEET METAL (FORMED): ±0.125"/3mm/±1° MACHINING: ±0.015623"/0.4mm
ASSEMBLY: ±0.125"/3mm
ISOMETRIC VIEW OF STRUCTURED PACKING SUPPORT GRID
(ONE)-REQ'D., BELOW BED #1
2 REVISED AS MARKED BTP HSK GB 28 FEB 24
1 REVISED AS MARKED & APPROVED FOR FABRICATION KRS HSK GB 18 JAN 24
PART LIST purposes permitted above, you are deemed to have agreed, in consideration for the supply of this drawing and/or connected information by KG, to be bound
QTY ITEM DESCRIPTION THICKNESS MATERIAL video recordings or any measurements of the drawing referenced herein to be taken by your employees or any third parties; and (iv) return it to KG upon
- - RIM 3.0mm 304L SS

- - CROSS BAR 3.0mm 304L SS
- - BEARING BAR 3.0mm 304L SS
A 1 700 BEARING BAR 3.0mm 304L SS Koch-Glitsch Italia SRL
A
REFER TO ELEVATION & ORIENTATION FOR: PAK-ARAB REFINERY LIMITED MODEL 802
2 701 BEARING BAR 3.0mm 304L SS DRAWING FOR ACTUAL EQUIPMENT USER: FATIMA FERTILIZER CO LTD STRUCTURED PACKING SUPPORT GRID
4 702 BOLTING PLATE 3.0mm 304L SS ELEVATION AND ORIENTATION GLYCOL ABSORBER
8 BOLT BOLT-FT 304L M10 x 25 AS NOTED 304L SS JOBSITE: MULTAN (PAKISTAN) 1130mm VESSEL I.D.
CUSTOMER TAG: ITEM NO:
8 NUT NUT 304L M10 AS NOTED 304L SS
PO NO: FPO-81967 T-100 KG00112636-007
8 WASHER WASH 304L 11 x 25 12g AS NOTED 304L SS PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 1 OF 2 REV
- - TOWER ATTACHMENTS - (EXISTING) ASSET NO: KG00112636 KG00112636-007 2
6 5 4 3 2 1
6 5 4 3 2 1
1130 TOWER I.D. (1226 LINED) 2 Please note that it is 1126mm after lining. Typo needs to be corrected
1090 20
CLR.
240.5 99 411 99 240.5
D D
102
CROSS BAR CROSS BAR
25.4
'B2' 'B2'
51
100
305
C BEARING BAR C
'A2' 'A2' BOLTING PLATE
BEARING BAR
SECTION 'B2'-'B2'
305
QUAN DESCRIPTION REMARKS
1 PLAN VIEW OF STRUCTURED PACKING SUPPORT GRID AS SHOWN
B B

1 APPROVED FOR FABRICATION KRS HSK GB 18 JAN 24
PLAN VIEW OF STRUCTURED PACKING SUPPORT GRID rights.For a list of some relevant patents and trademarks, please see www.koch-glitsch.com/legal-notices
(ONE)-REQ'D., BELOW BED #1 is proprietary and confidential information of Koch-Glitsch, LP or its respective affiliates, collectively doing business as Koch-Glitsch (KG), and shall not be
100

A
FOR: PAK-ARAB REFINERY LIMITED MODEL 802
USER: FATIMA FERTILIZER CO LTD STRUCTURED PACKING SUPPORT GRID
GLYCOL ABSORBER
SECTION 'A2'-'A2' REFER TO ELEVATION & ORIENTATION JOBSITE: MULTAN (PAKISTAN) 1130mm VESSEL I.D.
DRAWING FOR ACTUAL EQUIPMENT
ELEVATION AND ORIENTATION PO NO: FPO-81967 T-100 KG00112636-007
ASSET NO: KG00112636 KG00112636-007 2
6 5 4 3 2 1
6 5 4 3 2 1
THE DISTRIBUTOR FEED HOLE SIZE IS SHOWN IN THE PLAN.
INSTALLATION NOTES:
1. CRITICAL: ENSURE THAT COMPONENTS OF THE TROUGH ASSEMBLIES LABELED THE CUSTOMER SHOULD TAKE CORRECTIVE ACTION TO ELIMINATE
“SPLASH BAFFLE” ARE LOCATED ON THE SIDES OF THE TROUGHS CONTAINING FEED SOLIDS ACCUMULATION IN THE PROCESS. PARALLEL FILTERS ARE
3250R RECOMMENDED IN EXTERNAL FEED/REFLUX LINES TO PROTECT
HOLES, AND THAT COMPONENTS LABELED “BAFFLE PLATE” ARE LOCATED ON
8 653 NON-PERFORATED SIDES OF THE TROUGHS. AGAINST DISTRIBUTOR BLOCKAGE. KOCH-GLITSCH SUGGESTS THAT
1 2. ANY TIE-WIRE USED TO RETAIN COMPONENTS DURING SHIPPING IS TO BE REMOVED 0.3 mm (0.012 ") MAXIMUM OPENINGS BE USED FOR FILTER MESH,
AND DISCARDED. BUT ASSUMES NO RESPONSIBILITY FOR RECOMMENDING OR
3. TIE-WIRES TO BE REMOVED FROM TROUGH ASSEMBLY "650 & 651" DESIGNING FILTERS.
1 AFTER IT IS INSTALLED IN THE TOWER. SHOULD SOLIDS ACCUMULATION IMPAIR THE PERFORMANCE OF
D 4. THE TOP OF THE PARTING BOX SHOULD BE INSTALLED 122mm 4 ABOVE THE CENTER
LINE OF NOZZLE N3. THE FEED PIPE CAN THEN BE INSTALLED AND LEVELED WITH
THE DISTRIBUTOR(S). KOCH-GLITSCH'S PERFORMANCE WARRANTY
WILL BE VOIDED.
D
652 THE USE OF THE SHIMS SUPPLIED WITH KG00112636-004. REFER TO KOCH-GLITSCH'S TERMS AND CONDITIONS CONCERNING
1 RESPONSIBILITY FOR PROCESS CLEANLINESS.
REFERENCE DRAWING:
DRAWING KG00112636 FOR VESSEL ELEVATION. N O T E S
2
654 1. VESSEL MANHOLE I.D. ACTUAL: 603
4
MARK # (EG. 001-301).
APPROXIMATE WEIGHT OF 156 TROUGH DISTRIBUTOR 165 Kg 2 ARE REPRESENTED AS THUS:
3342A QUANTITY PER ASSEMBLY SHOWN 301
16 1

7. ANY MODIFICATIONS BY CUSTOMER OR ANY THIRD PARTY
655 TO THE EQUIPMENT SHOWN ON THIS DRAWING WITHOUT
2
C 8. ALL WARRANTIES AND VOIDANCES THERETO, ARE PER THE C
651 SELLER'S STANDARD TERMS AND CONDITIONS OR THE
2 9. THE DISTRIBUTOR PARTING BOX & TROUGHS TO BE
INSTALLED LEVEL TO WITHIN 3MM FROM HIGH POINT TO
LOW WITH A 13mm MINIMUM CLEARANCE ABOVE
THE HIGHEST TROUGH.
10. SPARE: BOLTING-5% , HARDWARE-5%.
DISTRIBUTOR FLOW RATES

MAXIMUM - - GPM 3.8 - M^3/HR
DESIGN - - GPM 3.5 - M^3/HR
16 WASHER WASH 304L 11 x 25 12g AS NOTED 304L SS - - GPM 1.7 - M^3/HR
MINIMUM
32 BOLT BOLT-FT 304L M10 x 25 AS NOTED 304L SS EQUIPMENT DESCRIPTION
16 NUT NUT 304L M12 AS NOTED 304L SS
QUAN ITEM DESCRIPTION REMARKS
4 WASHER Wash 304L 14x38 (12ga/2.5mm) AS NOTED 304L SS
1 - ISOMETRIC VIEW OF MODEL 156 TROUGH DISTRIBUTOR ABOVE BED
4 STUD STUD-FT 304L M12 x 200 AS NOTED 304L SS
B 650
20 BOLT BOLT-FT 304L M10 x 50 AS NOTED 304L SS B
2 72 NUT NUT 304L M10 AS NOTED 304L SS GENERAL TOLERANCE LEGEND (UNLESS NOTED OTHERWISE)
702 SHEET METAL (FLAT): ±0.125"/3mm SAWING: ±0.125"/3mm
12 - TROUGH END PLATE 2.5mm 304L SS
4 SHEET METAL (FORMED): ±0.125"/3mm/±1° MACHINING: ±0.015623"/0.4mm
- ASSEMBLY: ±0.125"/3mm
870 4 TR. BRACE ANGLE 2.5mm 304L SS
24 2 655 Z-BEAM 2.5mm 304L SS
2 450 SPLASH BAFFLE 2.5mm 304L SS
2 REVISED AS MARKED BTP HSK GB 28 Feb 24
ISOMETRIC VIEW OF MODEL 156 TROUGH DISTRIBUTOR 1
0
REVISED AS MARKED & APPROVED FOR FABRICATION
ORIGINAL DESIGN
HUT
HUT
HSK
HSK
GB
GB
06 Feb 24
22 Dec 23
ABOVE BED., (ONE)-REQ'D. REV DESCRIPTION BY CHK APP DATE
2 550 BAFFLE PLATE 2.5mm 304L SS
2 551 BAFFLE PLATE 2.5mm 304L SS AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500
2 552 BAFFLE PLATE 2.5mm 304L SS
FIELD INSTALLATION NOTE : 2 650 TROUGH 2.5mm 304L SS totally or partially, directly or indirectly transferred, disclosed to any person, copied, traced, photographed, reproduced in any manner, or used for any
BAFFLES SHALL BE INSERTED INTO THE TOWER PRIOR 2 651 TROUGH 2.5mm 304L SS equipment referenced herein, or (2) by written permission of KG. The equipment referenced herein shall not be reverse-engineered. KG retain all intellectual
TO THE TROUGHS. drawing and the information contained herein. By accepting, receiving and/or taking possession of and/or by making use of this drawing for either of the
1 652 PARTING BOX 2.5mm 304L SS purposes permitted above, you are deemed to have agreed, in consideration for the supply of this drawing and/or connected information by KG, to be bound
2 - PB END PLATE 2.5mm 304L SS video recordings or any measurements of the drawing referenced herein to be taken by your employees or any third parties; and (iv) return it to KG upon
INSTALLATION NOTE : request. Copyright 2024, Koch-Glitsch, LP
TYPICAL HARDWARE CONNECTIONS THROUGH REFER TO ELEVATION & ORIENTATION 2 - PDC SUPPORT 2.5mm 304L SS
THE PARTING BOX SHALL HAVE THE BOLT HEAD DRAWING FOR ACTUAL EQUIPMENT 1 653 PDC 2.0mm 304L SS
ON THE LIQUID SIDE WITH NO WASHER AS SHOWN, ELEVATION AND ORIENTATION
EXCEPT AT LOCATIONS WITH WELDED NUTS (IF APPLICABLE) 2 - PDC END PLATE 2.0mm 304L SS
A 4 654 LEVELING BRACKET 2.5mm 304L SS Koch-Glitsch Italia SRL
A
FOR: PAK-ARAB REFINERY LIMITED 156
4 700 SUPPORT CHANNEL 2.5mm 304L SS USER:FATIMA FERTILIZER CO LTD TROUGH DISTRIBUTOR
4 701 CROSS BAR 2.5mm 304L SS GLYCOL ABSORBER
4 702 CROSS BAR 2.5mm 304L SS JOBSITE: MULTAN (PAKISTAN) 1130mm - VESSEL I.D.
ASSEMBLY 3250R ASSEMBLY 3342A CUSTOMER TAG: ITEM NO:
24 870 SHIM 2.5mm 304L SS
1 M10 HEX NUT 891- 340F 03 1 M10 WELDED NUT 891- 340F 03 PO NO: FPO-81967 T-100 KG00112636-005
1 M10 X 25 BOLT 896- 340F 1305 1 WASHER 25 OD. 800- 340G 020801 QTY ITEM DESCRIPTION THICKNESS MATERIAL PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 1 OF 2 REV
1 M10 X 25 BOLT 896- 340F 1305
PART LIST ASSET NO: KG00112636 KG00112636-005 2
6 5 4 3 2 1
6 5 4 3 2 1
1130 VESSEL I.D. (1126 LINED) 2 255
PARTING BOX O/S 9500M 651
90 200 200 75 75 200 200
2 1
PARTING BOX
D PRE-DISTRIBUTOR CHANNEL D
PARTING BOX O/S

PDC SUPPORT
302.5
"D2"
700
"B2" LEVELING BRACKET
2
Z-BEAM
100
177.5
3253D
"A2" "A2" 8
SEE NOTE #9
ON SHEET-1
"D2"
13
SECTION "B2-B2" 551
1
C C
451 701
25 1 2
"C2" "C2" Z-BEAM
3250R
4
55 552
25 1
65
452
#651 TROUGH ASSEMBLY
1 (ALL HARDWARE & PART ARE SHOP ASSEMBLED)
"B2"
TROUGH
TROUGH 650
PLAN VIEW OF MODEL 156 TROUGH DISTRIBUTOR BRACE ANGLE 1
ABOVE BED., (ONE)-REQ'D. EQUIPMENT DESCRIPTION
QUAN ITEM DESCRIPTION REMARKS

SECTION "D2"-"D2" 1 - ISOMETRIC VIEW OF MODEL 156 TROUGH DISTRIBUTOR ABOVE BED
B B
67 GENERAL TOLERANCE LEGEND (UNLESS NOTED OTHERWISE)
122 (±4)
1 ASSEMBLY: ±0.125"/3mm
END PLATE
N3 TROUGH
1 REVISED AS MARKED & APPROVED FOR FABRICATION HUT HSK GB 06 Feb 24
TROUGH HEIGHT
SPLASH BAFFLE 0 ORIGINAL DESIGN HUT HSK GB 22 Dec 23
715.5 OVERALL HEIGHT
282
550 3253D AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500
1 2 rights.For a list of some relevant patents and trademarks, please see www.koch-glitsch.com/legal-notices
Ø4.2 ORIFICE 450
HOLE purpose whatsoever, except: (1) for the limited purpose of, and solely to the extent necessary for, the installation, operation or maintenance of the
1 equipment referenced herein, or (2) by written permission of KG. The equipment referenced herein shall not be reverse-engineered. KG retain all intellectual
BAFFLE property rights, whether registered or unregistered, including, but not limited to trade secrets, trademarks, patents, designs and copyrights, embodied in this
PLATE purposes permitted above, you are deemed to have agreed, in consideration for the supply of this drawing and/or connected information by KG, to be bound
276
230
#650 TROUGH ASSEMBLY

32
(ALL HARDWARE & PART ARE SHOP ASSEMBLED)

137
MIN.
118

A
FOR: PAK-ARAB REFINERY LIMITED 156
USER:FATIMA FERTILIZER CO LTD TROUGH DISTRIBUTOR
GLYCOL ABSORBER
8 Ø2.0 DRAIN HOLE JOBSITE: MULTAN (PAKISTAN) 1130mm - VESSEL I.D.
ONE PER TROUGH CUSTOMER TAG: ITEM NO:
ASSEMBLY 3250R ASSEMBLY 3253D ASSEMBLY 9500M
PO NO: FPO-81967 T-100 KG00112636-005
SECTION "A2"-"A2" SECTION "C2"-"C2" 1 M10 HEX NUT
1 M10 X 25 BOLT
891- 340F 03
896- 340F 1305
2 M10 HEX NUT
1 M10 X 50 BOLT
891- 340F 03
896- 340F 1310
4
1
M12 HEX NUT°
WASHER 38 OD.
M12 X 200 STUD
891- 340F 04
800- 340G 020102
867- 340F 0440
1
ASSET NO: KG00112636 KG00112636-005 2
6 5 4 3 2 1
6 5 4 3 2 1
GASKET GASKET
ASSEMBLY 3302A ASSEMBLY 4602P ASSEMBLY 9500P

1 M10 HEX NUT 891- 340F 03 4 M12 HEX NUT 891- 340F 04 4 M12 HEX NUT 891- 340F 04
1 WASHER 25 OD. 800- 340G 020801 FLANGE GSKT(2") 603 FLANGE GSKT(2") 604
1 M10 X 25 BOLT 896- 340F 1305 4 M12 X 50 BOLT 896- 340F 1410 4 M12 X 50 BOLT 896- 340F 1410
2" SHOP FLANGE, 6 MM THK 2" SHOP FLANGE, 10 MM THK
D D
603
2
APPROXIMATE WEIGHT OF FEED PIPE 50 Kg 2
4602P
3302A
1
4
601
1 N O T E S
1. VESSEL MANHOLE I.D. ACTUAL: 603mm 2
MARK # (EG. 001-301).
ARE REPRESENTED AS THUS:
QUANTITY PER ASSEMBLY SHOWN 301
1
C C
604 INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
2 OR FITNESS FOR PURPOSE.
870 NEGOTIATED TERMS SELLER HAS ACCEPTED.
600 20 9. FLANGE BOLT HOLES ARE TO STRADDLE NATURAL
CENTER LINE OF PIPE.
1 10. SPARE : NUTS & BOLTS = 10% (MIN. 2 Nos.)
WASHERS = 5% (MIN. 2 Nos.)
GASKET = 100%
REFER TO ELEVATION & ORIENTATION

ELEVATION AND ORIENTATION
B B
2 604 GASKET 3.0mm UNIVERSAL CARBON

2 603 GASKET 3.0mm UNIVERSAL CARBON
9500P 2 REVISED AS MARKED BTP HSK GB 28 FEB 24
602 1 1 602 PLATE FLANGE 10.0mm 304L SS 1 REVISED AS MARKED & APPROVED FOR FABRICATION KRS HSK GB 31 JAN 24
0 ORIGINAL DESIGN KRS HSK GB 29 DEC 23
1 1 1 601 LATERAL PIPE 2" SCH. 40S 304L SS
GASKET & SHIM QTY. 1 600 HEADER PIPE 2" SCH. 40S 304L SS
ISOMETRIC VIEW INCL. SPARE.
20 870 SHIM 2.0mm 304L SS AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500
- - SUPPORT BRACKET 2.0mm 304L SS rights.For a list of some relevant patents and trademarks, please see www.koch-glitsch.com/legal-notices
- - VENT CAP 2.0mm 304L SS
- - VENT COVER 2.0mm 304L SS equipment referenced herein, or (2) by written permission of KG. The equipment referenced herein shall not be reverse-engineered. KG retain all intellectual
- - BRACE 2.0mm 304L SS purposes permitted above, you are deemed to have agreed, in consideration for the supply of this drawing and/or connected information by KG, to be bound
- - DOWN TUBE 1" SCH. 40S 304L SS video recordings or any measurements of the drawing referenced herein to be taken by your employees or any third parties; and (iv) return it to KG upon
- - END PLATE 3.0mm 304L SS

- - PLATE FLANGE 6.0mm 304L SS
- - PLATE FLANGE 10.0mm 304L SS
A 4 NUT NUT 304L M10 AS NOTED 304L SS Koch-Glitsch Italia SRL
A
FOR: PAK-ARAB REFINERY LIMITED FEED PIPE DISTRIBUTOR
8 WASHER WASH 304L 11 x 25 12g AS NOTED 304L SS USER:Fatima Fertilizer Co Ltd AT EXISTING NOZZLE "N3"
4 BOLT BOLT-FT 304L M10 x 25 AS NOTED 304L SS glycol absorber
8 NUT NUT 304L M12 AS NOTED 304L SS JOBSITE: Multan (Pakistan) 1130mm - VESSEL I.D.
8 BOLT BOLT-FT 304L M12 x 50 AS NOTED 304L SS
PO NO: FPO-81967 T-100 KG00112636-004
QTY ITEM DESCRIPTION THICKNESS MATERIAL PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 1 OF 2 REV
6 5 4 3 2 1
6 5 4 3 2 1
1130 VESSEL I.D.(1126 LINED) 2 180 O.D. 152.4 O.D.

120.7 B.C.D.
1006 148 B.C.D. 10 THK. 6 THK.
62 I.D.
503 106.5 I.D.
453
REF.
3 1
THK. 88.5 102 3
TYP THK.
D D
125
45°
210 C/C
REF.
TYP.
45° (4)n15
TYP.
(4)n15 DETAILS OF PLATE FLANGE

SHIM
(10)-n10 SUPPORT BRACKET
DETAILS OF (602) VENT COVER
PLATE FLANGE PLATE FLANGE WITH VENT CAP
FEED HOLES
415
VENT HOLE
333
180 O.D. END PLATE LATERAL PIPE
148 B.C.D. 10 THK.
62 I.D.
C PLATE FLANGE
C
FEED HOLES
PLATE FLANGE
283.6
DOWN TUBE
234
INTERNAL PROJECTION 45°
(EXISTING) TYP.
N3
"A2" "A2" (4)n15

PLAN VIEW FEED PIPE DISTRIBUTOR BRACE
AT EXISTING NOZZLE "N3"
(ONE)-REQ'D. DETAILS OF PLATE FLANGE
79
565 TO CL.
"B2" 60.5 3 THK SECTION "C2"-"C2"

(2)n6 VENT HOLE
B 50 55 GASKET
B
"C2" GENERAL TOLERANCE LEGEND (UNLESS NOTED OTHERWISE)
HEADER PIPE SHEET METAL (FLAT): ±0.125"/3mm SAWING: ±0.125"/3mm
142 5
GAP
REF.
88
1
1 REVISED AS MARKED & APPROVED FOR FABRICATION KRS HSK GB 31 JAN 24
210
0 ORIGINAL DESIGN KRS HSK GB 29 DEC 23
234

45° AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500
7
n105
29
n50
N3 is proprietary and confidential information of Koch-Glitsch, LP or its respective affiliates, collectively doing business as Koch-Glitsch (KG), and shall not be
REF
76
1 property rights, whether registered or unregistered, including, but not limited to trade secrets, trademarks, patents, designs and copyrights, embodied in this
P.D.C. FLOOR P.D.C. FLOOR by a legal obligation to (i) keep this drawing and the information contained herein strictly confidential; (ii) solely grant access of this drawing to your
REF.

52
5
TYP.
5
3 THK 62.5
GASKET
A
"C2" "B2" FOR: PAK-ARAB REFINERY LIMITED FEED PIPE DISTRIBUTOR
REFER DWG. NO.
KG00112636-005
USER:Fatima Fertilizer Co Ltd AT EXISTING NOZZLE "N3"
SECTION "B2"-"B2" glycol absorber
VIEW "A2"-"A2" JOBSITE: Multan (Pakistan) 1130mm - VESSEL I.D.
REFER TO ELEVATION & ORIENTATION WELD SYMBOL NOTE: CUSTOMER TAG: ITEM NO:
DRAWING FOR ACTUAL EQUIPMENT FLAGS REPRESENTS LOCATIONS OF FIELD WELDS AND ALL PO NO: FPO-81967 T-100 KG00112636-004
ELEVATION AND ORIENTATION ASSOCIATION WELD PREPARATION (i.e. BEVELING, ETC.). PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 2 OF 2 REV
ASSET NO: KG00112636 KG00112636-004 2
6 5 4 3 2 1
6 5 4 3 2 1
DEMISTER® MIST ELIMINATOR NOTES
1 1. MESH FABRICATED OVERSIZE TO ENSURE SNUG FIT
1130 VESSEL I.D. (1126 LINED)
STANDARD RESISTANCE WELDED CONSTRUCTION.
2. INSTALLATION FROM: BOTTOM
384.5 361 3. SUPPORT GRID STYLE : TOP AND BOTTOM STANDARD RIGID WELDED AND FULLY BANDED
TYP. 4. MESH SECURED WITH: J-BOLT WITH CLAMPS
ASSEMBLY 9500A
5. TIE WIRE NOT TO BE USED TO SECURE SECTIONS TO EACH OTHER
16 348.5 321 2 M10 HEX NUT 891- 340F 03 AS THIS MAY CAUSE GAPS IN THE MESH.
TYP. TYP. 1 WASHER 25 OD 800- 340G 020801
1 M10 J-BOLT 966- 340F 21809
1 L- CLAMP 964- 340G 212
D D
4 APPROXIMATE WEIGHT OF DEMISTER® MIST ELIMINATOR 50 Kg
870
2 871
1
2
N O T E S
1. VESSEL MANHOLE I.D. ACTUAL: 603 4
MARK # (EG. 001-301).
'A1' 3. ITEMS & HARDWARE ASSEMBLIES FURNISHED
'A1' ARE REPRESENTED AS THUS:
C ITEM OR ASSEMBLY NO.
301
C
QUANTITY PER ASSEMBLY SHOWN
1

ISOMETRIC VIEW 3 VOID ALL EXPRESSED AND IMPLIED WARRANTIES,
9. SPARE: BOLTING-10% , HARDWARE-10%.
Ø6mm ROD
(TYP.) REFERENCE DRAWING:
DRAWING KG00112636 FOR VESSEL ELEVATION & ORIENTATION
10% NET FLOW AREA REFER TO ELEVATION & ORIENTATION

ELEVATION AND ORIENTATION
B B
YORKMESH SHEET METAL (FLAT):

SHEET METAL (FORMED):
±0.125"/3mm SAWING:
±0.125"/3mm/±1° MACHINING:
±0.125"/3mm
±0.015623"/0.4mm
PLAN VIEW OF DEMISTER® MIST ELIMINATOR 3

3 REVISED AS MARKED YSS HSK GB 06 Feb 24
2 REVISED AS MARKED & APPROVED FOR FABRICATION SPB HSK GB 30 JAN 24
(ONE)-REQ'D 1 REVISED AS MARKED SPB HSK GB 18 JAN 24
0 ORIGINAL DESIGN SPB HSK GB 29 DEC 23
FLOW DISTRIBUTION PLATE
HOLD DOWN DETAIL REV DESCRIPTION BY CHK APP DATE
THK.
2
TOP FLAT BAR rights.For a list of some relevant patents and trademarks, please see www.koch-glitsch.com/legal-notices
TOP OF MESH equipment referenced herein, or (2) by written permission of KG. The equipment referenced herein shall not be reverse-engineered. KG retain all intellectual
24 NUT NUT 304L M10 AS NOTED 304L SS property rights, whether registered or unregistered, including, but not limited to trade secrets, trademarks, patents, designs and copyrights, embodied in this
12 WASHER WASH 304L 11 x 25 12g AS NOTED 304L SS purposes permitted above, you are deemed to have agreed, in consideration for the supply of this drawing and/or connected information by KG, to be bound
1
1 YORKMESH
12 CLAMP Clamp-Grid 304L (7ga/4.88mm) AS NOTED 304L SS video recordings or any measurements of the drawing referenced herein to be taken by your employees or any third parties; and (iv) return it to KG upon
kinitted wire mesh
12 BOLT Bolt-J 304L M10 x 90 (45TL) AS NOTED 304L SS
247
245
195
- - FLOW DISTRIBUTION PLATE 2.0mm 304L SS

- - RIM 3.0mm 304L SS
A - - ROD 6mm ROD 304L SS Koch-Glitsch Italia SRL
A
- -
FOR: Fatima Fertilizer Co Ltd MODEL- DM SPL(709)
Rigid Welded Rod 6mm ROD 304L SS USER:-Lahore Cantt DEMISTER® MIST ELIMINATOR
BOTTOM FLAT BAR 2 - - GRID 3.0mm 304L SS glycol absorber
2 870 MESH PAD AS NOTED 304L SS JOBSITE: Fatima Fertilizer Co Ltd 1130mm - VESSEL I.D.
SECTION 'A1'-'A1' 3
EXISTING SUPPORT
REF.DWG. NO:- KG00112636 1 871 MESH PAD AS NOTED 304L SS
Multan (Pakistan) CUSTOMER TAG:
T-100
ITEM NO:
KG00112636-003
PO NO: FPO-81967
QTY ITEM DESCRIPTION THICKNESS MATERIAL PROJECT NO: AA1622901 THIRD ANGLE: DRAWING NUMBER: 1 OF 1 REV
6 5 4 3 2 1

Absorber Packing Drawings

Uploaded by

Copyright:

Available Formats

Absorber Packing Drawings

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Absorber Packing Drawings

Uploaded by

Copyright:

Available Formats

6 5 4 3 2 1

C FLEXIPAC® 250Y HC® HALF C

7465 TAN LINE TO TAN LINE

N1 E.L. +837 N1 E.L. +837 NOZZLE SIZE SERVICE

1 N10B 0.5" DIFFERENTIAL PRESSURE TRANSMITTER

N12 24" MANWAY W/ BLIND & DAVIT

270° 90° 270° 90° 270° 90°

ORIENTATION OF DEMISTER® MIST ELIMINATOR

ORIENTATION OF FEED PIPE DISTRIBUTOR AT NOZZLE 'N3' ORIENTATION OF TROUGH DISTRIBUTOR

SUPPORT GRID ORIENTATION CORRECTED

F3 FOR PARTS & SERVICE: WWW.KOCH-GLITSCH.COM

B QUAN DESCRIPTION REMARKS B

REVISED AS MARKED & CERTIFIED FINAL AS

A Koch-Glitsch Italia SRL

1130 TOWER I.D.(1126 LINED) 2

1 M12 HEX NUT (EXISTING)

REV DESCRIPTION BY CHK APP DATE

AMERICAS 1.888.562.4911 | EUROPE/MIDDLE EAST/AFRICA/INDIA +39.06.928.911 | ASIA PACIFIC +65.6831.6500

60 60 request. Copyright 2023, Koch-Glitsch, LP

A Koch-Glitsch Italia SRL

LIST OF MATERIAL FOR: PAK-ARAB REFINERY LIMITED TOWER ATTACHMENTS

DESCRIPTION TYPE & THICKNESS

2 APPROXIMATE WEIGHT OF STRUCTURED PACKING SUPPORT GRID 35 Kg

4. SPARE HARDWARE IS PROVIDED AS QUOTED, BUT

- - RIM 3.0mm 304L SS

2 REVISED AS MARKED BTP HSK GB 28 FEB 24

A Koch-Glitsch Italia SRL

4. SPARE HARDWARE IS PROVIDED AS QUOTED, BUT

DISTRIBUTOR FLOW RATES

PARTING BOX O/S

QUAN ITEM DESCRIPTION REMARKS

#650 TROUGH ASSEMBLY

(ALL HARDWARE & PART ARE SHOP ASSEMBLED)

A Koch-Glitsch Italia SRL

ASSEMBLY 3302A ASSEMBLY 4602P ASSEMBLY 9500P

REFER TO ELEVATION & ORIENTATION

2 604 GASKET 3.0mm UNIVERSAL CARBON

- - END PLATE 3.0mm 304L SS

1130 VESSEL I.D.(1126 LINED) 2 180 O.D. 152.4 O.D.

(4)n15 DETAILS OF PLATE FLANGE

"A2" "A2" (4)n15

"B2" 60.5 3 THK SECTION "C2"-"C2"

REV DESCRIPTION BY CHK APP DATE

request. Copyright 2024, Koch-Glitsch, LP

4. SPARE HARDWARE IS PROVIDED AS QUOTED, BUT

10% NET FLOW AREA REFER TO ELEVATION & ORIENTATION

YORKMESH SHEET METAL (FLAT):

4 REVISED AS MARKED BTP HSK GB 28 Feb 24

PLAN VIEW OF DEMISTER® MIST ELIMINATOR 3

- - FLOW DISTRIBUTION PLATE 2.0mm 304L SS

You might also like