NOTICE :When inspecting or repairing the SRS, perform service in accordance with the following precautionary

instructions and the procedure, and precautions in the Repair Manual applicable for the model year. (IG) (IG) D1
Combination Meter
* Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of
information when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting 7.5A 7.5A
the battery. IGN MET

* Work must be started more than 90 seconds after the ignition switch is turned to the "LOCK" position (Ignition switch
Type) or the power switch is Pushed to the "OFF" poition (Power switch type) and the negative (-) terminal cable is

SRS
disconnected from the battery.
16 4E 1 4M
(The SRS is equipped with a back-up power source so that if work is started within 90 seconds from disconnecting LED Driver
the negative (-) terminal cable of the battery, the SRS may deploy.)

* When the negative (-) terminal cable is disconnected from the battery, the memory of the clock and audio system
will be cleared. So before starting work, make a record of the contents in the audio memory system. When work is CPU
finished, reset the audio systems as they were before and adjust the clock. Some vehicles have power tilt
steering, power telescopic steering, power seat and power outside rear view mirror which are all equipped with CAN Controller
memory function. However, it is not possible to make a record of these memory contents. So when the work is

B
finished, it will be necessary to explain it to your customer, and ask the customer to adjust the features and
reset the memory. To avoid erasing the memory in each system, never use a back-up power supply from outside the
vehicle. CAN I/F

* Before repair, remove the airbag sensor if shocks are likely to be applied to the sensor during repair.

* Do not expose the following parts directly to hot air or flame; A5 A11 1 21 20 24
Front Airbag Sensor Front Airbag Sensor D15(A),D79(B)
RH LH DLC3

BR
* Even in cases of a minor collision where the SRS does not deploy, the following parts should be inspected;

G
D45(A),D78(B)
* Never use SRS parts from another vehicle. When replacing parts, replace with new parts.
18 A 7 A (*1)

Connector
+SR -SR +SL -SL SIL 18 B 7 B (*2)

Junction
* For the purpose of reuse, never disassemble and repair the following parts.
2 1 2 1 7 A (*1)
7 B (*2)
* If the following parts have been dropped, or have cracks, dents and other defects in their case, bracket,
22 A 11 A (*1)
and connector replace with new one.
22 B 11 B (*2)
* Use a volt/ohmmeter with high impedance (10 kΩ/V minimum) for troubleshooting electrical circuits of the system.

W
B

Y
* Information labels are attached to the periphery of the SRS components. Follow the instructions of the notice. D44(A),D77(B)
Junction 22 A 11 A (*1)
Connector 22 B 11 B (*2)
* After work on the SRS is completed, check the SRS warning light.
7 4E
A20
* If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the Engine ECU
1 AD1 2 AD1 3 AD1 4 AD1
Repair Manual. CANH CANL 15 A 4 A 19 A 8 A (*1)
31 4E 41 49 15 B 4 B 19 B 8 B (*2)
16
W W
* Steering wheel pad AD4
* Front passenger airbag assembly

W
B

B
* Seat belt pretensioner 15
L L
* Center airbag sensor assembly AD4
* Front airbag sensor assembly
D16(A),J9(B),J10(C)
21 A 29 A 27 A 30 A 28 A Center Airbag ECU 16 A 22 A 13 A
IG2 +SR -SR +SL -SL SIL CANL CANH

E2 E1 P+ P- D+ D- PP+ PP- PD+ PD-

26 A 25 A 4 A 3 A 5 A 6 A 4 C 5 C 2 B 1 B D16(A),J9(B),J10(C)
Center Airbag ECU

W-B

W-B

Y-B

Y-B

Y-B

Y-B
Y

Y
1 DP1 2 DP1
14 4E 30 4E
1 A 2 A
* 1 :Before Mar. 2012 Production
D17(A),T1(B) * 2 :From Mar. 2012 Production

Y-G
Y-R
Spiral Cable

BR
17 4E
2 1 2 B 1 B 2 1 2 1
W-B

P1 T1(B) J18 J17

Front Passenger Side Driver Side Pretensioner LH Pretensioner RH
Squib Circuit Squib Circuit

D2 D3