STP Report 2019 20

JAIPUR ENGINEERING COLLEGE AND RESEARCH CENTRE
A Report
On Industrial Visit of
8 MLD STP at
BrahmpuriJaipur
Session 2019-2020
Department of Civil Engineering
February 2020
Aim: -
The objective of the Industrial visit was to acknowledge the student about
Sewage treatment plant and to give them practical knowledge about how the
sewage water is being treated These days and is being used in agriculture. By
this, they will be able to solve the common engineering problem related to
treatment of water occur in an Engineer’s life. Industrial Visit is considered as
one of the tactical methods of teaching interaction, working methods and
employment practices, Moreover, it gives exposure from academic point of
view. Main aim of industrial visit is to provide an exposure to students about
practical working environment. They also provide students a good opportunity
to gain full awareness about engineering practices. Through these visits the
students get awareness about new technologies. By these practices they can
share their knowledge with their colleagues.
Overview:-
Department of Civil Engineering of Jaipur Engineering College and Research
Centre Organised this visit to the Sewage treatment Plant on the 6th February
2020, at Brahmpuri Jaipur for the third-year students of Civil Engineering Batch
A.
The Sewage treatment Plant named as 8 Million Liters per day Sequential Batch
Reactor Sewage treatment Plant Brahmpuri is was established in 2019 with an
objective of treating water By PHED Rajasthan.
Group Photograph of the students with officials

About:-
The Sewage treatment Plant is the plant constructed to dispose the municipal
and industrial waste water for its reuse and to reduce the consumption of the
pure water than usual which helps to save the environment. The 8MLD STP
was a small plant with the limit of treating 8 million liters of waster water per
day which connects its lines with the Jaisinghpura STP and takes the 8 Million
liters of inlet from it and let the rest of 60 million waster water lead to the
Jaisingpura STP It works on Solar energy as there are lot of Solar panel are
installed. Like every other STP it has two equipment for each process.
Group Picture of Students with officials at the Sewage Treatment

Plant
Salient Features of 8 MLD STP

S.No Particulars Details
1 Capacity 8 Milliion Liters per day
2 Technology used Sequential Batch reactor
3 Process Activated Sludge process with
anaerobic digester and centrifuge
unit
4 Design of Flow on main Sewer 50 Million liters per day
Methodology: -
Folllowing Methods were carried on the plant
a) Screening:-screening is the first unit operation used at STP to remove

objects such as paper plastics etc. There were processes of screening
named as : Coarse Screening and fine
Screeing
In Coarse screeing the size of the screen was 20 mm wide. Weather In fine
screening the size of the screen was 10mm.
b) Pumping:-sewer pumping is used to move sewage water to higher

level in order to allow transport of sewage by gravity flow.
c) Grit Separator:-the grit is seperated by the grit seperator which is

the part of primary treatment unit. After the screening the water is
pumped to the higher level and after that fall of the water is provided so
that the heavy particles like grit should be placed in the lower part and
then the grit seperator seprate the grit from the sewage water and water is
allowed to pass from the top of it.
d) Parshall Fluming: -after the seperation of grit, the water is passed

for the further treatment but the velocity of water need to be constant for
that a parshall flume is required for maintaining the velocity of water and
it is transferred to the sedimentation tank.
e) Aeration:-in the Aeration process the water is passed into a

sedimentaiton tank and then the oxygen is transferred in the water to
remove the sludge by bacteria. This process takes place for about 140
minutes. In this process the Aeration stops and starts for several times to
maintain the amount of oxygen into the water ( 2.1mg/l).
Aeration Process at the sewage treatment plant
f) Sedimentation:-After Aeration the water is allowed to settle down

and the process of sedimentation takes place for about 33 minutes and the
sludge is settled down to the surface.
g) Decantation:-in the decantation process the sedimented water is

allowed to flow from the top surface for about 1.5 meters from top
without distubing the setteled sludge and then the water is supplied.
Uses of Treated Water:-

 This can be used in Ponds .
 This is mostly used in agriculture as the plant get their nutrients from
it.
Conclusion:-
By this visit students learnt methods to clean water by SBR technology
and they learnt various methods at different stages of cleaning and how
we can use the waste water as a Recycling material.

STP Report 2019 20

Uploaded by

Copyright:

Available Formats

STP Report 2019 20

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

STP Report 2019 20

Uploaded by

Copyright:

Available Formats

JAIPUR ENGINEERING COLLEGE AND RESEARCH CENTRE

Group Photograph of the students with officials

Group Picture of Students with officials at the Sewage Treatment

Salient Features of 8 MLD STP

a) Screening:-screening is the first unit operation used at STP to remove

b) Pumping:-sewer pumping is used to move sewage water to higher

c) Grit Separator:-the grit is seperated by the grit seperator which is

d) Parshall Fluming: -after the seperation of grit, the water is passed

e) Aeration:-in the Aeration process the water is passed into a

Aeration Process at the sewage treatment plant

f) Sedimentation:-After Aeration the water is allowed to settle down

g) Decantation:-in the decantation process the sedimented water is

Uses of Treated Water:-

You might also like