SAFETY DATA SHEET

DDP SPECIALTY ELECTRONIC MATERIALS

US 9, LLC

Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Print Date: 06/23/2023

DDP SPECIALTY ELECTRONIC MATERIALS US 9, LLC encourages and expects you to read and
understand the entire (M)SDS, as there is important information throughout the document. We expect
you to follow the precautions identified in this document unless your use conditions would necessitate
other appropriate methods or actions.

1. IDENTIFICATION
Product name: MOLYKOTE® 55 O-Ring Grease
Recommended use of the chemical and restrictions on use
Identified uses: Lubricants and lubricant additives

COMPANY IDENTIFICATION
DDP SPECIALTY ELECTRONIC MATERIALS
US 9, LLC
974 Centre Road
Wilmington DE 19805
UNITED STATES

Customer Information Number: 833-338-7668

[email protected]

EMERGENCY TELEPHONE NUMBER

24-Hour Emergency Contact: 1-800-424-9300
Local Emergency Contact: 800-424-9300

2. HAZARDS IDENTIFICATION
Hazard classification
GHS classification in accordance with 29 CFR 1910.1200
Skin sensitisation - Category 1

Label elements
Hazard pictograms

Signal word: WARNING!

® ™ Trademark of affiliates of DuPont de Nemours, Inc. Page 1 of 13

Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Hazards
May cause an allergic skin reaction.

Precautionary statements
Prevention
Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray.
Contaminated work clothing must not be allowed out of the workplace.
Wear protective gloves.

Response
IF ON SKIN: Wash with plenty of soap and water.
If skin irritation or rash occurs: Get medical advice/ attention.
Wash contaminated clothing before reuse.

Disposal
Dispose of contents/ container to an approved waste disposal plant.

Other hazards
No data available

3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical nature: Silicone grease.

This product is a mixture.
Component CASRN Concentration

Lithium stearate 4485-12-5 >= 17.0 - <= 25.0 %

2,5-Furandione, dihydro-3-(tetrapropenyl)- 26544-38-7 >= 0.37 - <= 0.49 %

4. FIRST AID MEASURES

Description of first aid measures
General advice:
First Aid responders should pay attention to self-protection and use the recommended protective
clothing (chemical resistant gloves, splash protection). If potential for exposure exists refer to Section
8 for specific personal protective equipment.

Inhalation: Move person to fresh air; if effects occur, consult a physician.

Skin contact: Remove material from skin immediately by washing with soap and plenty of water.
Remove contaminated clothing and shoes while washing. Seek medical attention if irritation persists.
Wash clothing before reuse. Discard items which cannot be decontaminated, including leather articles
such as shoes, belts and watchbands. Suitable emergency safety shower facility should be available
in work area.

Page 2 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Eye contact: Flush eyes thoroughly with water for several minutes. Remove contact lenses after the
initial 1-2 minutes and continue flushing for several additional minutes. If effects occur, consult a
physician, preferably an ophthalmologist.

Ingestion: No emergency medical treatment necessary.

Most important symptoms and effects, both acute and delayed:

Aside from the information found under Description of first aid measures (above) and Indication of
immediate medical attention and special treatment needed (below), any additional important
symptoms and effects are described in Section 11: Toxicology Information.

Indication of any immediate medical attention and special treatment needed

Notes to physician: No specific antidote. Treatment of exposure should be directed at the control of
symptoms and the clinical condition of the patient.

5. FIREFIGHTING MEASURES
Suitable extinguishing media: Water spray Alcohol-resistant foam Carbon dioxide (CO2) Dry
chemical

Unsuitable extinguishing media: None known.

Special hazards arising from the substance or mixture

Hazardous combustion products: Silicon oxides Carbon oxides

Unusual Fire and Explosion Hazards: Exposure to combustion products may be a hazard to health.

Advice for firefighters

Fire Fighting Procedures: Fire residues and contaminated fire extinguishing water must be disposed
of in accordance with local regulations.
Use extinguishing measures that are appropriate to local circumstances and the surrounding
environment. Use water spray to cool unopened containers. Collect contaminated fire extinguishing
water separately. This must not be discharged into drains. Remove undamaged containers from fire
area if it is safe to do so. Evacuate area.

Special protective equipment for firefighters: In the event of fire, wear self-contained breathing
apparatus. Use personal protective equipment.

6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures: Use personal protective
equipment. Follow safe handling advice and personal protective equipment recommendations.

Environmental precautions: Discharge into the environment must be avoided. Prevent further
leakage or spillage if safe to do so. Retain and dispose of contaminated wash water. Local
authorities should be advised if significant spillages cannot be contained.

Methods and materials for containment and cleaning up: Wipe up or scrape up and contain for
salvage or disposal. Local or national regulations may apply to releases and disposal of this material,
as well as those materials and items employed in the cleanup of releases. You will need to determine
which regulations are applicable. For large spills, provide dyking or other appropriate containment to

Page 3 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

keep material from spreading. If dyked material can be pumped, Sections 13 and 15 of this SDS
provide information regarding certain local or national requirements.
See sections: 7, 8, 11, 12 and 13.

7. HANDLING AND STORAGE

Precautions for safe handling: Do not get on skin or clothing. Do not swallow. Avoid contact with
eyes. Take care to prevent spills, waste and minimize release to the environment. Handle in
accordance with good industrial hygiene and safety practice.
Use only with adequate ventilation. See Engineering measures under EXPOSURE
CONTROLS/PERSONAL PROTECTION section.

Conditions for safe storage: Keep in properly labelled containers. Store in accordance with the
particular national regulations.

Do not store with the following product types: Strong oxidizing agents.
Unsuitable materials for containers: None known.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Control parameters
If exposure limits exist, they are listed below. If no exposure limits are displayed, then no values are
applicable.
Component Regulation Type of listing Value
Lithium stearate CAL PEL PEL 10 mg/m3
ACGIH TWA Inhalable 10 mg/m3
particulate matter
Further information: LRT irr: Lower Respiratory Tract irritation; J: Does not include
stearates of toxic metals.; A4: Not classifiable as a human carcinogen; varies: varies
ACGIH TWA Respirable 3 mg/m3
particulate matter
Further information: LRT irr: Lower Respiratory Tract irritation; J: Does not include
stearates of toxic metals.; A4: Not classifiable as a human carcinogen; varies: varies

Exposure controls
Engineering controls: Use engineering controls to maintain airborne level below exposure limit
requirements or guidelines. If there are no applicable exposure limit requirements or guidelines, use
only with adequate ventilation. Local exhaust ventilation may be necessary for some operations.

Hygiene measures: Use good personal hygiene. Do not consume or store food in the work area.
Wash hands before smoking or eating. Ensure that eye flushing systems and safety showers are
located close to the working place.

Individual protection measures

Eye/face protection: Use safety glasses (with side shields).
Skin protection
Hand protection: Use gloves chemically resistant to this material. NOTICE: The selection of a
specific glove for a particular application and duration of use in a workplace should also take into
account all relevant workplace factors such as, but not limited to: Other chemicals which may be
handled, physical requirements (cut/puncture protection, dexterity, thermal protection), potential body
reactions to glove materials, as well as the instructions/specifications provided by the glove supplier.

Page 4 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Other protection: Use protective clothing chemically resistant to this material. Selection of specific
items such as face shield, boots, apron, or full body suit will depend on the task.
Respiratory protection: Respiratory protection should be worn when there is a potential to exceed
the exposure limit requirements or guidelines. If there are no applicable exposure limit requirements or
guidelines, wear respiratory protection when adverse effects, such as respiratory irritation or
discomfort have been experienced, or where indicated by your risk assessment process. For
emergency conditions, use an approved positive-pressure self-contained breathing apparatus.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance
Physical state Grease
Color white
Odor slight
Odor Threshold No data available
pH Not applicable
Melting point/range No data available
Freezing point No data available
Boiling point (760 mmHg) Not applicable
Flash point closed cup >101.1 °C ( 214.0 °F)
Evaporation Rate (Butyl Acetate Not applicable
= 1)
Flammability (solid, gas) Not classified as a flammability hazard
Lower explosion limit No data available
Upper explosion limit No data available
Vapor Pressure Not applicable
Relative Vapor Density (air = 1) No data available
Relative Density (water = 1) 1.1
Water solubility No data available
Partition coefficient: n- No data available
octanol/water
Auto-ignition temperature No data available
Decomposition temperature No data available
Dynamic Viscosity Not applicable
Kinematic Viscosity Not applicable
Explosive properties Not explosive

Oxidizing properties The substance or mixture is not classified as oxidizing.

Liquid Density 1.1 g/cm3
Molecular weight No data available
Particle size No data available

NOTE: The physical data presented above are typical values and should not be construed as a
specification.

Page 5 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

10. STABILITY AND REACTIVITY

Reactivity: Not classified as a reactivity hazard.

Chemical stability: Stable under normal conditions.

Possibility of hazardous reactions: Can react with strong oxidizing agents.

Conditions to avoid: None known.

Incompatible materials: Oxidizing agents

Hazardous decomposition products: Benzene.

11. TOXICOLOGICAL INFORMATION

Toxicological information appears in this section when such data is available.

Acute toxicity
Acute oral toxicity
Product test data not available. Refer to component data.

Acute dermal toxicity

Product test data not available. Refer to component data.

Acute inhalation toxicity

Product test data not available. Refer to component data.

Skin corrosion/irritation
Product test data not available. Refer to component data.

Serious eye damage/eye irritation

Product test data not available. Refer to component data.

Sensitization
Product test data not available. Refer to component data.

Specific Target Organ Systemic Toxicity (Single Exposure)

Product test data not available. Refer to component data.

Specific Target Organ Systemic Toxicity (Repeated Exposure)

Product test data not available. Refer to component data.

Carcinogenicity
Product test data not available. Refer to component data.

Teratogenicity

Page 6 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Product test data not available. Refer to component data.

Reproductive toxicity
Product test data not available. Refer to component data.

Mutagenicity
Product test data not available. Refer to component data.

Aspiration Hazard
Product test data not available. Refer to component data.

COMPONENTS INFLUENCING TOXICOLOGY:

Lithium stearate
Acute oral toxicity
For similar material(s): LD50, Rat, > 5,000 mg/kg

Acute dermal toxicity

Based on data from similar materials LD50, Rat, > 2,000 mg/kg OECD Test Guideline 402

Acute inhalation toxicity

The LC50 has not been determined.

Skin corrosion/irritation
Brief contact is essentially nonirritating to skin.

Serious eye damage/eye irritation

May cause slight eye irritation.
Corneal injury is unlikely.

Sensitization
For skin sensitization:
For similar material(s):
Did not demonstrate the potential for contact allergy in mice.

For respiratory sensitization:

No relevant data found.

Specific Target Organ Systemic Toxicity (Single Exposure)

Evaluation of available data suggests that this material is not an STOT-SE toxicant.

Specific Target Organ Systemic Toxicity (Repeated Exposure)

For similar material(s):
Based on available data, repeated exposures are not anticipated to cause significant adverse
effects.

Carcinogenicity
No relevant data found.

Teratogenicity
No relevant data found.

Reproductive toxicity
No relevant data found.

Page 7 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Mutagenicity
For similar material(s): In vitro genetic toxicity studies were negative.

Aspiration Hazard
Based on physical properties, not likely to be an aspiration hazard.

2,5-Furandione, dihydro-3-(tetrapropenyl)-
Acute oral toxicity
LD50, Rat, 1,875 mg/kg

Acute dermal toxicity

LD50, Rabbit, 2,006 mg/kg

Acute inhalation toxicity

For similar material(s): LC50, Rat, male and female, 4 Hour, dust/mist, 5.3 mg/l

Skin corrosion/irritation
Prolonged contact may cause slight skin irritation with local redness.
Repeated contact may cause slight skin irritation with local redness.

Serious eye damage/eye irritation

May cause moderate eye irritation.
Corneal injury is unlikely.

Sensitization
For similar material(s):
Has caused allergic skin reactions when tested in guinea pigs.

For respiratory sensitization:

No relevant data found.

Specific Target Organ Systemic Toxicity (Single Exposure)

Evaluation of available data suggests that this material is not an STOT-SE toxicant.

Specific Target Organ Systemic Toxicity (Repeated Exposure)

Based on available data, repeated exposures are not anticipated to cause significant adverse
effects.

Carcinogenicity
No relevant data found.

Teratogenicity
For similar material(s): Did not cause birth defects or any other fetal effects in laboratory
animals.

Reproductive toxicity
For similar material(s): In animal studies, did not interfere with reproduction.

Mutagenicity
For similar material(s): In vitro genetic toxicity studies were negative.

Aspiration Hazard
Based on physical properties, not likely to be an aspiration hazard.

Page 8 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

12. ECOLOGICAL INFORMATION

Ecotoxicological information appears in this section when such data is available.

Toxicity

Lithium stearate
Acute toxicity to fish
Material is practically non-toxic to aquatic organisms on an acute basis
(LC50/EC50/EL50/LL50 >100 mg/L in the most sensitive species tested).
Based on data from similar materials
LL50, Oncorhynchus mykiss (rainbow trout), 96 Hour, > 100 mg/l, OECD Test Guideline 203

Acute toxicity to aquatic invertebrates

Based on data from similar materials
EL50, Daphnia magna (Water flea), 48 Hour, > 100 mg/l, OECD Test Guideline 202

Acute toxicity to algae/aquatic plants

Based on data from similar materials
EL50, Pseudokirchneriella subcapitata (green algae), 72 Hour, > 100 mg/l, OECD Test
Guideline 201

Toxicity to bacteria
Based on data from similar materials
NOEC, activated sludge, static test, 28 d, 13 mg/l

2,5-Furandione, dihydro-3-(tetrapropenyl)-
Acute toxicity to fish
Material is practically non-toxic to aquatic organisms on an acute basis
(LC50/EC50/EL50/LL50 >100 mg/L in the most sensitive species tested).
LC50, Oncorhynchus mykiss (rainbow trout), semi-static test, 96 Hour, > 100 mg/l, OECD Test
Guideline 203 or Equivalent

Acute toxicity to aquatic invertebrates

For similar material(s):
EC50, Daphnia dubia (water flea), 48 Hour, > 100 mg/l, OECD Test Guideline 202

Acute toxicity to algae/aquatic plants

EC50, Pseudokirchneriella subcapitata (green algae), static test, 96 Hour, Growth rate, 110
mg/l

Toxicity to bacteria
EC50, activated sludge, static test, 3 Hour, Respiration rates., 800 mg/l, OECD Test Guideline
209

Persistence and degradability

Lithium stearate
Biodegradability: Material is readily biodegradable. Passes OECD test(s) for ready
biodegradability.
Based on data from similar materials 10-day Window: Not applicable

Page 9 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Biodegradation: 78 %
Exposure time: 28 d
Method: OECD Test Guideline 301C

2,5-Furandione, dihydro-3-(tetrapropenyl)-
Biodegradability: Biodegradation under aerobic static laboratory conditions is low (BOD20 or
BOD28/ThOD between 2.5 and 10%).
10-day Window: Fail
Biodegradation: 9.9 %
Exposure time: 28 d
Method: OECD Test Guideline 301D

Photodegradation
Sensitization: OH radicals
Atmospheric half-life: 1.7 - 1.9 Hour
Method: Estimated.
Photodegradation
Sensitization: Ozone.
Atmospheric half-life: 1.4 - 2.1 Hour
Method: Estimated.

Bioaccumulative potential

Lithium stearate
Bioaccumulation: Based on data from similar materials No relevant data found.
Bioconcentration factor (BCF): 0.12 Fish

2,5-Furandione, dihydro-3-(tetrapropenyl)-
Bioaccumulation: Bioconcentration potential is moderate (BCF between 100 and 3000 or
Log Pow between 3 and 5).
Partition coefficient: n-octanol/water(log Pow): > 4.39 OECD Test Guideline 107

Mobility in soil

Lithium stearate
No relevant data found.

2,5-Furandione, dihydro-3-(tetrapropenyl)-
Potential for mobility in soil is low (Koc between 500 and 2000).
Partition coefficient (Koc): 825 Measured

13. DISPOSAL CONSIDERATIONS

Disposal methods: DO NOT DUMP INTO ANY SEWERS, ON THE GROUND, OR INTO ANY BODY
OF WATER. All disposal practices must be in compliance with all Federal, State/Provincial and local
laws and regulations. Regulations may vary in different locations. Waste characterizations and
compliance with applicable laws are the responsibility solely of the waste generator. AS YOUR
SUPPLIER, WE HAVE NO CONTROL OVER THE MANAGEMENT PRACTICES OR
MANUFACTURING PROCESSES OF PARTIES HANDLING OR USING THIS MATERIAL. THE
INFORMATION PRESENTED HERE PERTAINS ONLY TO THE PRODUCT AS SHIPPED IN ITS
INTENDED CONDITION AS DESCRIBED IN MSDS SECTION: Composition Information. FOR
UNUSED & UNCONTAMINATED PRODUCT, the preferred options include sending to a licensed,

Page 10 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

permitted: Incinerator or other thermal destruction device. For additional information, refer to:
Handling & Storage Information, MSDS Section 7 Stability & Reactivity Information, MSDS Section10
Regulatory Information, MSDS Section 15

Treatment and disposal methods of used packaging: Empty containers should be recycled or
otherwise disposed of by an approved waste management facility. Waste characterizations and
compliance with applicable laws are the responsibility solely of the waste generator. Do not re-use
containers for any purpose.

14. TRANSPORT INFORMATION

DOT
Not regulated for transport

Classification for SEA transport (IMO-IMDG):

Not regulated for transport
Transport in bulk Consult IMO regulations before transporting ocean bulk
according to Annex I or II
of MARPOL 73/78 and the
IBC or IGC Code

Classification for AIR transport (IATA/ICAO):

Not regulated for transport

This information is not intended to convey all specific regulatory or operational

requirements/information relating to this product. Transportation classifications may vary by container
volume and may be influenced by regional or country variations in regulations. Additional
transportation system information can be obtained through an authorized sales or customer service
representative. It is the responsibility of the transporting organization to follow all applicable laws,
regulations and rules relating to the transportation of the material.

15. REGULATORY INFORMATION

Superfund Amendments and Reauthorization Act of 1986 Title III (Emergency Planning and
Community Right-to-Know Act of 1986) Sections 311 and 312
Respiratory or skin sensitisation

Superfund Amendments and Reauthorization Act of 1986 Title III (Emergency Planning and
Community Right-to-Know Act of 1986) Section 313
This material does not contain any chemical components with known CAS numbers that exceed the
threshold (De Minimis) reporting levels established by SARA Title III, Section 313.

Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA)

Section 103
This material does not contain any components with a CERCLA RQ.

Page 11 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

Pennsylvania Right To Know

The following chemicals are listed because of the additional requirements of Pennsylvania law:

Components CASRN
Poly(dimethylsiloxane)copolymer 63148-52-7
Lithium stearate 4485-12-5
Di-2-ethylhexyl sebacate 122-62-3

California Prop. 65
This product does not contain any chemicals known to State of California to cause cancer, birth
defects, or any other reproductive harm.

United States TSCA Inventory (TSCA)

All components of this product are in compliance with the inventory listing requirements of the U.S.
Toxic Substances Control Act (TSCA) Chemical Substance Inventory.

16. OTHER INFORMATION

Hazard Rating System

NFPA
Health Flammability Instability
2 1 0
HMIS
Physical
Health Flammability
Hazard
2/ 1 0

Revision
Identification Number: 4000034 / A776 / Issue Date: 07/22/2021 / Version: 6.0
Most recent revision(s) are noted by the bold, double bars in left-hand margin throughout this
document.

Legend
ACGIH USA. ACGIH Threshold Limit Values (TLV)
CAL PEL California permissible exposure limits for chemical contaminants (Title 8, Article
107)
PEL Permissible exposure limit
TWA 8-hour, time-weighted average

Full text of other abbreviations

AIIC - Australian Inventory of Industrial Chemicals; ASTM - American Society for the Testing of
Materials; bw - Body weight; CERCLA - Comprehensive Environmental Response, Compensation,
and Liability Act; CMR - Carcinogen, Mutagen or Reproductive Toxicant; DIN - Standard of the
German Institute for Standardisation; DOT - Department of Transportation; DSL - Domestic
Substances List (Canada); ECx - Concentration associated with x% response; EHS - Extremely
Hazardous Substance; ELx - Loading rate associated with x% response; EmS - Emergency Schedule;
ENCS - Existing and New Chemical Substances (Japan); ErCx - Concentration associated with x%
growth rate response; ERG - Emergency Response Guide; GHS - Globally Harmonized System; GLP
- Good Laboratory Practice; HMIS - Hazardous Materials Identification System; IARC - International
Agency for Research on Cancer; IATA - International Air Transport Association; IBC - International
Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk; IC50 - Half

Page 12 of 13
Product name: MOLYKOTE® 55 O-Ring Grease Issue Date: 07/22/2021

maximal inhibitory concentration; ICAO - International Civil Aviation Organization; IECSC - Inventory of
Existing Chemical Substances in China; IMDG - International Maritime Dangerous Goods; IMO -
International Maritime Organization; ISHL - Industrial Safety and Health Law (Japan); ISO -
International Organisation for Standardization; KECI - Korea Existing Chemicals Inventory; LC50 -
Lethal Concentration to 50 % of a test population; LD50 - Lethal Dose to 50% of a test population
(Median Lethal Dose); MARPOL - International Convention for the Prevention of Pollution from Ships;
MSHA - Mine Safety and Health Administration; n.o.s. - Not Otherwise Specified; NFPA - National Fire
Protection Association; NO(A)EC - No Observed (Adverse) Effect Concentration; NO(A)EL - No
Observed (Adverse) Effect Level; NOELR - No Observable Effect Loading Rate; NTP - National
Toxicology Program; NZIoC - New Zealand Inventory of Chemicals; OECD - Organization for
Economic Co-operation and Development; OPPTS - Office of Chemical Safety and Pollution
Prevention; PBT - Persistent, Bioaccumulative and Toxic substance; PICCS - Philippines Inventory of
Chemicals and Chemical Substances; (Q)SAR - (Quantitative) Structure Activity Relationship; RCRA -
Resource Conservation and Recovery Act; REACH - Regulation (EC) No 1907/2006 of the European
Parliament and of the Council concerning the Registration, Evaluation, Authorisation and Restriction of
Chemicals; RQ - Reportable Quantity; SADT - Self-Accelerating Decomposition Temperature; SARA -
Superfund Amendments and Reauthorization Act; SDS - Safety Data Sheet; TCSI - Taiwan Chemical
Substance Inventory; TECI - Thailand Existing Chemicals Inventory; TSCA - Toxic Substances Control
Act (United States); UN - United Nations; UNRTDG - United Nations Recommendations on the
Transport of Dangerous Goods; vPvB - Very Persistent and Very Bioaccumulative

Information Source and References

This SDS is prepared by Product Regulatory Services and Hazard Communications Groups from
information supplied by internal references within our company.

DDP SPECIALTY ELECTRONIC MATERIALS US 9, LLC urges each customer or recipient of this
(M)SDS to study it carefully and consult appropriate expertise, as necessary or appropriate, to become
aware of and understand the data contained in this (M)SDS and any hazards associated with the
product. The information herein is provided in good faith and believed to be accurate as of the
effective date shown above. However, no warranty, express or implied, is given. Regulatory
requirements are subject to change and may differ between various locations. It is the buyer's/user's
responsibility to ensure that his activities comply with all federal, state, provincial or local laws. The
information presented here pertains only to the product as shipped. Since conditions for use of the
product are not under the control of the manufacturer, it is the buyer's/user's duty to determine the
conditions necessary for the safe use of this product. Due to the proliferation of sources for
information such as manufacturer-specific (M)SDSs, we are not and cannot be responsible for
(M)SDSs obtained from any source other than ourselves. If you have obtained an (M)SDS from
another source or if you are not sure that the (M)SDS you have is current, please contact us for the
most current version.
US

Page 13 of 13