Scribd
Upload
133 views8 pages

How To Clear CPS Alarm

The document provides steps to resolve rectifier, controller, and battery discharge alarms. It describes checking rectifier LED lights, resetting or replacing controller boards, and removing faulty rectifiers from the system.

Uploaded by

sarla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
133 views8 pages

How To Clear CPS Alarm

The document provides steps to resolve rectifier, controller, and battery discharge alarms. It describes checking rectifier LED lights, resetting or replacing controller boards, and removing faulty rectifiers from the system.

Uploaded by

sarla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 8

RECTIFIER ALARM

Go to the Controller
Press MENU – ALARM.
Controller will read out the fail rectifier e.g Gxx
Main Alarms:
a) AC Failure / Phase Alarm
b) Rectifier Failure / High Voltage

STEP 1. SET THE FAULTY RECTIFIER IN STANBY MOOD


STEP 2. SWITCH OFF THE FAULTY RECTIFIER’S MCB
STEP 3. TURN LOSE ANTIQUE CLOCK WISE THE RECTIFIER BY USING ORANGE ELENKEY SLOWLY
UNTIL THE LED LIGHTS ON THE DISPLAY OF RECTIFIER GOES OFF
STEP 4. SLOWLY PULL OUT THE RECTIFIER CAREFULLY
STEP 5. GO TO THE GPS CONTROLLER AND SELLECT MAIN MENU

STEP 6. GO TO MAIN MENU, THEN STEP 7. THEN PRESS RECTIFIER


PRESS CONFIGERATION MANAGER

STEP 9. GO TO REMOVE RECTIFIER


STEP 8. AFTER ENTER RECTIFIER AND KEY IN THE ID NUMBER, THEN
MANAGER, PRESS RECTIFIER PRESS ENTER
OPERATION
CONTROLLER ALARM

STEP 1. FIND THE CONTROLLER BOX INSIDE THE BAY 1 DOOR

STEP 2. THERE WILL BE TWO NUTS BENEATH THE CONTROLLER. UNSCREW THEM CAREFULLY.
STEP 3. OPEN THE LEFT SMALL DOOR BY PRESSING THE SMALL BUTTON DOWN

STEP 4. PUSH THE RIGHT HAND SIDE PLATE TOWARDS YOUR RIGHT CAREFULLY
STEP 5. SEE THE LIGHTS ON THE BASIC AND INTELLIGENT BOADRS. IF THE LEDS LIGHTS ONLY GREEN,
THEN THE BOARD IS OK. IF BOTH GREEN AND YELLOW LIGHT, SOMETHING WRONG WITH THE BOARD

INTELLIGENT BOARD LED LIGHTS

BASIC BOARD LED LIGHTS

STEP 6. IF BOTH THE GREEN AND


YELLOW LED LIGHTS, TRY TO RESET BY
PRESSING THE RESET BOTTON. IF THE
ALARM STILL APPEARS, THE BOARD
MUST BE CHANGED
STEP 7. IF WE STILL CAN’T CLEAR THE
ALARM, PULL OUT THE AC INPUT
CABLE OUT. THE ALARM AT NMC WILL
BE CLEARED BUT STILL APPEARS AT
TOC UNTIL THE BOARDS ARE
CHANGED
BATTERY ON DISCHARGE
THE BATTERY ON DISCHARGE ALARM ALLWAYS TAKE PLACE :-

1. WHEN THE TNB SUPPLY IS DOWN

2. MAIN AC BREAKER TRIPED

3. PHASE ALARM - SINGLE PHASE


A) SINGLE RECTIFIER FAILURE ( PULL OUT THE RECTIFIER )
B) MULTIPLE RECTIFIER FAILURE ( IT WON’T TAKE PLACE )

- THREE PHASE
A) SINGLE RECTIFIER FAILURE ( PULL OUT THE RECTIFIER)
B) MULTIPLE RECTIFIER FAILURE ( OPEN THE RECTIFIER’ S
MCB BOX AND FIND THE
COLOURS OF THE FAULTY
RECTIFIER CABLES
ARE SAME OR NOT. IF
CABLES SAME, THE CHARGEMAN
WILL KNOW WHAT TO DO.
IF THE COLOURS OF THE
CABLES ARE NOT THE
SAME, THERE IS A MAJOR
PROBLEM WITH THE
INCOMING AC SUPPLY
AND THE CABLES MUST BE
MONITORED USING A
DEVICE, ITS CALLED
TRANSIENT AC LOW OR
HIGH )
4. WHILE THE TIME CHANGING CURRENT FROM GENERATOR TO TNB SUPPLY
AGAIN

TERMAL PROB ALARM

TERMAL ALARM WILL ALLWAYS TAKE PLACE WHEN THE TERMAL CABLE FROM THE BATTERY
BANK SPOILED OR CONTROLER BOARD ( BASIC OR INTELEGENT) FAILURE.
STEP 1. TRY BY PULLING OUT THE TERMAL CABLE GENTLY.
STEP 2. AFTER PULLOUT THE CABLE, GO TO THE CONTROLLER AND SELLECT MENU >>
MAINTENANCE OPERATION>>CLEAR EVENTS>>PRESS TWO TIMES
STEP 3. IF THE ALARM STILL NOT CLEARED, THERE’S SOMETHING WRONG WITH THE
CONTROLER BOARDS (NEED TO BE CHANGED OR PULLOUT THE AC INPUT
CABLE FROM THE BOARD)

NOTE :- AFTER WE REPAIR THE ALARM FAULTY, WE NEED TO GO TO


THE CONTROLLER AND SELECT MENU>>MAINTENANCE
OPERATION>>CLEAR EVENT>>PRESS TWO TIMES TO MAKE
THE ALARM DISAPPEAR. FOR RECTIFIER FAILURE, WE ONLY
TO GO MENU>>CONFIGURATION>>RECTIFIER MANAGER>>
RECTIFIER OPERATION>>REMOVE RECTIFIER>>ENTER
RECTIFIER ID NUMBER e.g Gxx>>ENTER

You might also like