Cisco Spanning Tree Protocol Guide (STP Examples and Co... https://www.networkstraining.

com/cisco-spanning-tree-protocol/
NETWORKS TRAINING

HOME Cisco Networking Cisco ASA Certifications Training ABOUTGeneral

MY BOOKS SUGGESTED TRAINING
Cisco Routers

Cisco Switches

You are here: Home / Cisco Switches / Cisco Spanning Tree Protocol Guide (STP Examples and Configuration)

Cisco Spanning Tree Protocol Guide (STP Examples and Configuration)

Written By Harris Andrea

Spanning Tree Protocol (STP) ensures a loop-free topology in a local area network (LAN) made up of switches.

It is desirable to have redundant links in a switched LAN so that a single link failure cannot interrupt normal operation
of the network.

But redundant links may also introduce physical switching loops that are undesirable. STP allows to have physical
redundancy while preventing loops and associated drawbacks.

Spanning Tree Protocol is standardized as IEEE 802.1D. Cisco introduced several enhancements to the standard STP
operation that were later incorporated in Rapid Spanning Tree Protocol (RSTP) defined as IEEE 802.1w.

We will focus on Spanning Tree Protocol (STP) configuration and verification commands in this tutorial, as
implemented on Cisco switches. Figure 1 shows the topology with three Cisco Catalyst 3550 switches that have been
used.

Figure 1 Spanning Tree Protocol on Cisco Switches

1 of 8 20/10/2023, 12:04 PM
Cisco Spanning Tree Protocol Guide (STP Examples and Co... https://www.networkstraining.com/cisco-spanning-tree-protocol/
NETWORKS TRAINING
There are three trunk links as shown in Figure 1:

ABOUT MY BOOKS SUGGESTED TRAINING

SW1 Fa0/1 – SW2 Fa0/1
SW2 Fa0/2 – SW3 Fa0/1
SW3 Fa0/2 – SW1 Fa0/2

The three switches were interconnected and turned on and without any additional configuration the three trunks were
negotiated dynamically by Dynamic Trunking Protocol (DTP). Let’s verify the trunks are successfully established on
SW1.

SW1#show interfaces trunk

Port Mode Encapsulation Status Native vlan

Fa0/1 desirable n-isl trunking 1

Fa0/2 desirable n-isl trunking 1

<Output omitted for brevity>

You can use similar commands on SW2 and SW3 to verify successful trunk establishment. Three spanning tree
modes can be configured on Cisco switches as shown in the output below.

SW1(config)#spanning-tree mode ?
mst Multiple spanning tree mode
pvst Per-Vlan spanning tree mode
rapid-pvst Per-Vlan rapid spanning tree mode

By default, Cisco Catalyst 3550 switches used to build this scenario have spanning tree enabled in pvst mode. PVST
stands for Per-VLAN Spanning Tree Protocol and this mode runs an instance of IEEE 802.1d STP for each VLAN.

The output of show spanning-tree summary command below shows that spanning tree is running in pvst mode on
SW1.

SW3#show spanning-tree summary

Switch is in pvst mode

Root bridge for: none
Extended system ID is enabled
Portfast Default is disabled
PortFast BPDU Guard Default is disabled
Portfast BPDU Filter Default is disabled
Loopguard Default is disabled
EtherChannel misconfig guard is enabled
UplinkFast is disabled
BackboneFast is disabled
Configured Pathcost method used is short

<Output omitted for brevity>

The first step in spanning tree convergence involves electing the root switch. The switch with the lowest bridge ID wins
the election.

The standard bridge ID is an 8-byte value made up of a 2-byte priority and a 6-byte MAC address unique to that
switch. You can use show spanning-tree bridge id command to find out the bridge ID of a switch.

MORE READING: Cisco Switch EtherChannel Configuration - LACP - PAgP

2 of 8 20/10/2023, 12:04 PM
Cisco Spanning Tree Protocol Guide (STP Examples and Co... https://www.networkstraining.com/cisco-spanning-tree-protocol/
NETWORKS TRAINING
SW1#show spanning-tree bridge id
VLAN0001 8001.0016.c831.9000 ABOUT MY BOOKS SUGGESTED TRAINING

SW2#show spanning-tree bridge id

VLAN0001 8001.000f.24b7.1400

SW3#show spanning-tree bridge id

VLAN0001 8001.000f.233b.8a80

The switch with the lowest bridge ID wins the root election. In our scenario, SW3 happens to have the lowest bridge ID
so it should become the root switch.

You can influence the root switch election for a VLAN by manipulating the priority as shown below, however we are
sticking to the default priority in this scenario.

SW3(config)#spanning-tree vlan 1 pri

SW3(config)#spanning-tree vlan 1 priority ?

<0-61440> bridge priority in increments of 4096

You can see by running command show spanning-tree root that the root ID matches the bridge ID of SW3 indicating
that it is the root switch.

Please note in the command output below that the priority is shown as a decimal value 32769 that equals hexadecimal
8001 shown as part of all bridge IDs earlier.

SW3#show spanning-tree root

Root Hello Max Fwd

Vlan Root ID RootCost HelloTime MaxAge FwdDly Root Port
———- ——————– —- ——- — —– ———

VLAN0001 32769 000f.233b.8a80 0 2 20 15

The next step in STP convergence is for each switch to determine its root port (RP) which is the one port with the least
cost path back to the root.

Path cost is calculated by simply adding the spanning tree cost of all outgoing interfaces on the path to the root switch.
Fast Ethernet interfaces used in this scenario have a default cost of 19 each.

The root switch does not have a root port because it is itself the root; all the ports on the root switch are designated
ports. SW1 settles with having Fa0/2 as its root port while SW2 also has its Fa0/2 as root port.

The last major step invloves determining the desginated port (DP) for each segment. When multiple switches connect
to the same segment, this is the switch interface that provides the least cost path back to the root for that segment.

Our scenario has three segments and a single designated port has been determined for each as shown in the figure.
The show spanning-tree command executed on SW1, SW2, and SW3 validates these facts.

SW1#show spanning-tree

VLAN0001

Spanning tree enabled protocol ieee

Root ID Priority 32769
Address 000f.233b.8a80
Cost 19
3 of 8 20/10/2023, 12:04 PM
Cisco
Port Spanning Tree Protocol Guide (STP Examples and Co...
2 (FastEthernet0/2) https://www.networkstraining.com/cisco-spanning-tree-protocol/
NETWORKS TRAINING
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
Address 0016.c831.9000 ABOUT MY BOOKS SUGGESTED TRAINING
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300

MORE READING: Cisco Switching Products

Interface Role Sts Cost Prio.Nbr Type

——————- —- — ——— ——– —————–

Fa0/1 Altn BLK 19 128.1 P2p

Fa0/2 Root FWD 19 128.2 P2p

SW2#show spanning-tree

VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 32769
Address 000f.233b.8a80
Cost 19
Port 2 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Address 000f.24b7.1400
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300

Interface Role Sts Cost Prio.Nbr Type

——————- —- — ——— ——– —————–

Fa0/1 Desg FWD 19 128.1 P2p

Fa0/2 Root FWD 19 128.2 P2p

SW3#show spanning-tree

VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 32769
Address 000f.233b.8a80
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
Address 000f.233b.8a80
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300

Interface Role Sts Cost Prio.Nbr Type

——————- —- — ——— ——– —————–

Fa0/1 Desg FWD 19 128.1 P2p

Fa0/2 Desg FWD 19 128.2 P2p

Let’s change the port cost on Fa0/2 of SW2 from default of 19 to 39 and see how port roles change. At the moment
4 of 8 20/10/2023, 12:04 PM
Cisco
Fa0/2Spanning Tree
is the root portProtocol
on SW2 Guide (STP Examples
providing the leaseand
costCo...
path tohttps://www.networkstraining.com/cisco-spanning-tree-protocol/
the root switch SW3.
NETWORKS TRAINING
SW2>enable
SW2#configure terminal ABOUT MY BOOKS SUGGESTED TRAINING

Enter configuration commands, one per line. End with CNTL/Z.

SW2(config)#interface FastEthernet0/2
SW2(config-if)#spanning-tree cost 39
SW2(config-if)#end
SW2#

After this change, spanning tree would re-converge, having SW2 choose the indirect path through SW1 to reach the
root switch SW3 because it now happens to be the least cost path with cost 38.

The direct path SW2 has to the root switch SW3 via Fa0/2 has now cost 39 and is not the best cost path. SW2 would
put Fa0/1 in forwarding state as root port while Fa0/2 would be put in the blocking state as shown here.

SW2#show spanning-tree

VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 32769
Address 000f.233b.8a80
Cost 38
Port 1 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Address 000f.24b7.1400
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300

Interface Role Sts Cost Prio.Nbr Type

——————- —- — ——— ——– —————–

Fa0/1 Root FWD 19 128.1 P2p

Fa0/2 Altn BLK 39 128.2 P2p

You should proceed and run show spanning-tree command on SW1 and SW3 as well to find out how the spanning
tree topology changed after re-convergence.

Related Posts
How to Find a Device MAC Address on a Cisco Switch (show mac address-table)
How to Configure a Loopback Interface on Cisco Router & Switch
Cisco Switch Layer2 Layer3 Design and Configuration
Description of Switchport Mode Access vs Trunk Modes on Cisco Switches
What is an SFP Port-Module in Network Switches and Devices

Filed Under: Cisco Switches

Download Free Cisco Commands Cheat Sheets

Enter your Email below to Download our Free Cisco Commands Cheat Sheets for Routers, Switches and
ASA Firewalls.

Email
5 of 8 20/10/2023, 12:04 PM
CiscoThank
Spanning
you Tree Protocol
so much for Guide (STP Examples
hard working andbest
to provide Co...material
https://www.networkstraining.com/cisco-spanning-tree-protocol/
and services to me and other people. I am
NETWORKS
wondering TRAINING
if you have a book about SWITCHING, basically your collection of all SWITCH materials in a book
?
Please let me know. ABOUT MY BOOKS SUGGESTED TRAINING

Thank you again and God bless

Harris Andrea says

February 16, 2020 at 10:07 am

Mans, unfortunately I don’t have a switching book. Sorry about that.

Harris

suresh perer says

February 27, 2020 at 5:28 pm

SURESH PERERA

February 27,2020 at 2000

This lesson are very important all net work student.so i appreciate that. then this lesson be help my studies.
i wish you. this work.continue do this.good luck and goad bless you………………………………..

suresh………………..

Leave a Reply
Your email address will not be published. Required fields are marked *

Comment *

Name *

Email *

POST COMMENT

7 of 8 20/10/2023, 12:04 PM
SEARCH THIS SITE