Module 4: Inter-VLAN Routing

Professor Dr. Ahmed K. Al-Ani

Switching, Routing and Wireless Essentials v7.0 (SRWE)

©2
2
0
1
6
C
i
Module Objectives
s
c
o
a
n
Module Title: Inter-VLAN Routing
d
/
o
r Module Objective: Troubleshoot inter-VLAN routing on Layer 3 devices
i
t
s
a
f
f Topic Title Topic Objective
i
l
i
a Inter-VLAN Routing Operation Describe options for configuring inter-VLAN routing.
t
e
s
Router-on-a-Stick Inter-VLAN
.
Configure router-on-a-stick inter-VLAN routing.
A
l Routing
l
r
i Inter-VLAN Routing using Layer 3
g Configure inter-VLAN routing using Layer 3 switching.
h
t
Switches
s
r
e Troubleshoot common inter-VLAN configuration
s Troubleshoot Inter-VLAN Routing
e
r
issues.
v
e
d
.
C
i
s
c
o © 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 2
C
o
n
4.1 Inter-VLAN Routing
Operation

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 3
Inter-VLAN Routing Operation
What is Inter-VLAN Routing?
VLANs are used to segment switched Layer 2 networks for a variety of reasons. Regardless of the
reason, hosts in one VLAN cannot communicate with hosts in another VLAN unless there is a router or
a Layer 3 switch to provide routing services.

Inter-VLAN routing is the process of forwarding network traffic from one VLAN to another VLAN.

There are three inter-VLAN routing options:

• Legacy Inter-VLAN routing - This is a legacy solution. It does not scale well.
• Router-on-a-Stick - This is an acceptable solution for a small to medium-sized network.
• Layer 3 switch using switched virtual interfaces (SVIs) - This is the most scalable solution for
medium to large organizations.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 4
Inter-VLAN Routing Operation
Legacy Inter-VLAN Routing
• The first inter-VLAN routing solution relied on using a router with multiple Ethernet interfaces. Each
router interface was connected to a switch port in different VLANs. The router interfaces served as
the default gateways to the local hosts on the VLAN subnet.
• Legacy inter-VLAN routing using physical interfaces works, but it has a significant limitation. It is
not reasonably scalable because routers have a limited number of physical interfaces. Requiring
one physical router interface per VLAN quickly exhausts the physical interface capacity of a router.
• Note: This method of inter-VLAN routing is no longer implemented in switched networks and is
included for explanation purposes only.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 5
Inter-VLAN Routing Operation
Router-on-a-Stick Inter-VLAN Routing
The ‘router-on-a-stick’ inter-VLAN routing method overcomes the limitation of the legacy inter-VLAN routing
method. It only requires one physical Ethernet interface to route traffic between multiple VLANs on a
network.
• A Cisco IOS router Ethernet interface is configured as an 802.1Q trunk and connected to a trunk port on
a Layer 2 switch. Specifically, the router interface is configured using subinterfaces to identify routable
VLANs.
• The configured subinterfaces are software-based virtual interfaces. Each is associated with a single
physical Ethernet interface. Subinterfaces are configured in software on a router. Each subinterface is
independently configured with an IP address and VLAN assignment. Subinterfaces are configured for
different subnets that correspond to their VLAN assignment. This facilitates logical routing.
• When VLAN-tagged traffic enters the router interface, it is forwarded to the VLAN subinterface. After a
routing decision is made based on the destination IP network address, the router determines the exit
interface for the traffic. If the exit interface is configured as an 802.1q subinterface, the data frames are
VLAN-tagged with the new VLAN and sent back out the physical interface
Note: The router-on-a-stick method of inter-VLAN routing does not scale beyond 50 VLANs.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 6
Inter-VLAN Routing Operation
Inter-VLAN Routing on a Layer 3 Switch
The modern method of performing inter-VLAN routing is to use Layer 3 switches and switched virtual
interfaces (SVI). An SVI is a virtual interface that is configured on a Layer 3 switch, as shown in the
figure.

Note: A Layer 3 switch is also called a multilayer switch as it operates at Layer 2 and Layer 3.
However, in this course we use the term Layer 3 switch.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 7
Inter-VLAN Routing Operation
Inter-VLAN Routing on a Layer 3 Switch (Cont.)
Inter-VLAN SVIs are created the same way that the management VLAN interface is configured. The
SVI is created for a VLAN that exists on the switch. Although virtual, the SVI performs the same
functions for the VLAN as a router interface would. Specifically, it provides Layer 3 processing for
packets that are sent to or from all switch ports associated with that VLAN.

The following are advantages of using Layer 3 switches for inter-VLAN routing:
• They are much faster than router-on-a-stick because everything is hardware switched and routed.
• There is no need for external links from the switch to the router for routing.
• They are not limited to one link because Layer 2 EtherChannels can be used as trunk links
between the switches to increase bandwidth.
• Latency is much lower because data does not need to leave the switch in order to be routed to a
different network.
• They more commonly deployed in a campus LAN than routers.
• The only disadvantage is that Layer 3 switches are more expensive.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 8
4.2 Router-on-a-Stick Inter-
VLAN Routing

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 9
Router-on-a-Stick Inter-VLAN Routing
Router-on-a-Stick Scenario
• In the figure, the R1 GigabitEthernet 0/0/1 interface is
connected to the S1 FastEthernet 0/5 port. The S1
FastEthernet 0/1 port is connected to the S2 FastEthernet
0/1 port. These are trunk links that are required to forward
traffic within and between VLANs.
• To route between VLANs, the R1 GigabitEthernet 0/0/1
interface is logically divided into three subinterfaces, as
shown in the table. The table also shows the three VLANs
that will be configured on the switches.
• Assume that R1, S1, and S2 have initial basic
configurations. Currently, PC1 and PC2 cannot ping each
other because they are on separate networks. Only S1 and
S2 can ping each other, but they but are unreachable by Subinterface VLAN IP Address
PC1 or PC2 because they are also on different networks.
G0/0/1.10 10 192.168.10.1/24
• To enable devices to ping each other, the switches must be
configured with VLANs and trunking, and the router must be G0/0/1.20 20 192.168.20.1/24
configured for inter-VLAN routing.
G0/0/1.30 99 192.168.99.1/24
© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 10
Router-on-a-Stick Inter-VLAN Routing
S1 VLAN and Trunking Configuration
Complete the following steps to configure S1 with VLANs and trunking:
• Step 1. Create and name the VLANs.
• Step 2. Create the management interface.
• Step 3. Configure access ports.
• Step 4. Configure trunking ports.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 11
Router-on-a-Stick Inter-VLAN Routing
S2 VLAN and Trunking Configuration
The configuration for S2
is similar to S1.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 12
Router-on-a-Stick Inter-VLAN Routing
R1 Subinterface Configuration
The router-on-a-stick method requires you to create a subinterface for each VLAN to be routed.
A subinterface is created using the interface interface_id subinterface_id global configuration
mode command. The subinterface syntax is the physical interface followed by a period and a
subinterface number. Although not required, it is customary to match the subinterface number
with the VLAN number.
Each subinterface is then configured with the following two commands:
• encapsulation dot1q vlan_id [native] - This command configures the subinterface to
respond to 802.1Q encapsulated traffic from the specified vlan-id. The native keyword
option is only appended to set the native VLAN to something other than VLAN 1.
• ip address ip-address subnet-mask - This command configures the IPv4 address of the
subinterface. This address typically serves as the default gateway for the identified VLAN.
Repeat the process for each VLAN to be routed. Each router subinterface must be assigned an
IP address on a unique subnet for routing to occur. When all subinterfaces have been created,
enable the physical interface using the no shutdown interface configuration command. If the
physical interface is disabled, all subinterfaces are disabled.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 13
Router-on-a-Stick Inter-VLAN Routing
R1 Subinterface Configuration (Cont.)
In the configuration, the R1
G0/0/1 subinterfaces are
configured for VLANs 10, 20,
and 99.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 14
Router-on-a-Stick Inter-VLAN Routing
Verify Connectivity Between PC1 and PC2
The router-on-a-stick configuration is complete
after the switch trunk and the router
subinterfaces have been configured. The
configuration can be verified from the hosts,
router, and switch.

From a host, verify connectivity to a host in

another VLAN using the ping command. It is a
good idea to first verify the current host IP
configuration using the ipconfig Windows host
command.

Next, use ping to verify connectivity with PC2

and S1, as shown in the figure.
The ping output successfully confirms inter-
VLAN routing is operating.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 15
Router-on-a-Stick Inter-VLAN Routing
Router-on-a-Stick Inter-VLAN Routing Verification
In addition to using ping between devices, the following show commands can
be used to verify and troubleshoot the router-on-a-stick configuration.
• show ip route
• show ip interface brief
• show interfaces
• show interfaces trunk

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 16
Router-on-a-Stick Inter-VLAN Routing
Packet Tracer– Configure Router-on-a-Stick Inter-VLAN
Routing
In this Packet Tracer, you will complete the following objectives:
• Part 1: Add VLANs to a Switch
• Part 2: Configure Subinterfaces
• Part 3: Test connectivity with Inter-VLAN Routing

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 17
4.3 Inter-VLAN Routing using
Layer 3 Switches

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 18
Inter-VLAN Routing using Layer 3 Switches
Layer 3 Switch Inter-VLAN Routing
Inter-VLAN routing using the router-on-a-stick method is simple to implement for a small to
medium-sized organization. However, a large enterprise requires a faster, much more scalable
method to provide inter-VLAN routing.

Enterprise campus LANs use Layer 3 switches to provide inter-VLAN routing. Layer 3 switches
use hardware-based switching to achieve higher-packet processing rates than routers. Layer 3
switches are also commonly implemented in enterprise distribution layer wiring closets.

Capabilities of a Layer 3 switch include the ability to do the following:

• Route from one VLAN to another using multiple switched virtual interfaces (SVIs).
• Convert a Layer 2 switchport to a Layer 3 interface (i.e., a routed port). A routed port is
similar to a physical interface on a Cisco IOS router.
• To provide inter-VLAN routing, Layer 3 switches use SVIs. SVIs are configured using the
same interface vlan vlan-id command used to create the management SVI on a Layer 2
switch. A Layer 3 SVI must be created for each of the routable VLANs.
© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 19
Inter-VLAN Routing using Layer 3 Switches
Layer 3 Switch Scenario

In the figure, the Layer 3

switch, D1, is connected to
two hosts on different VLANs.
PC1 is in VLAN 10 and PC2
is in VLAN 20, as shown. The
Layer 3 switch will provide
inter-VLAN routing services
to the two hosts.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 20
Inter-VLAN Routing using Layer 3 Switches
Layer 3 Switch Configuration
Complete the following steps to configure S1 with VLANs and
trunking:
• Step 1. Create the VLANs. In the example, VLANs 10
and 20 are used.
• Step 2. Create the SVI VLAN interfaces. The IP address
configured will serve as the default gateway for hosts in
the respective VLAN.
• Step 3. Configure access ports. Assign the appropriate
port to the required VLAN.
• Step 4. Enable IP routing. Issue the ip routing global
configuration command to allow traffic to be exchanged
between VLANs 10 and 20. This command must be
configured to enable inter-VAN routing on a Layer 3
switch for IPv4.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 21
Inter-VLAN Routing using Layer 3 Switches
Layer 3 Switch Inter-VLAN Routing Verification
Inter-VLAN routing using a Layer 3 switch is simpler to configure than the router-on-a-
stick method. After the configuration is complete, the configuration can be verified by
testing connectivity between the hosts.
• From a host, verify connectivity to a host in another VLAN using the ping command. It
is a good idea to first verify the current host IP configuration using
the ipconfig Windows host command.
• Next, verify connectivity with PC2 using the ping Windows host command.
The successful ping output confirms inter-VLAN routing is operating.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 22
Inter-VLAN Routing using Layer 3 Switches
Routing on a Layer 3 Switch
If VLANs are to be reachable by other Layer 3 devices, then they must be advertised
using static or dynamic routing. To enable routing on a Layer 3 switch, a routed port must
be configured.

A routed port is created on a Layer 3 switch by disabling the switchport feature on a Layer
2 port that is connected to another Layer 3 device. Specifically, configuring the no
switchport interface configuration command on a Layer 2 port converts it into a Layer 3
interface. Then the interface can be configured with an IPv4 configuration to connect to a
router or another Layer 3 switch.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 23
Inter-VLAN Routing using Layer 3 Switches
Routing Scenario on a Layer 3 Switch
In the figure, the previously configured D1 Layer
3 switch is now connected to R1. R1 and D1 are
both in an Open Shortest Path First (OSPF)
routing protocol domain. Assume inter-VLAN has
been successfully implemented on D1. The
G0/0/1 interface of R1 has also been configured
and enabled. Additionally, R1 is using OSPF to
advertise its two networks, 10.10.10.0/24 and
10.20.20.0/24.

Note: OSPF routing configuration is covered in

another course. In this module, OSPF
configuration commands will be given to you in all
activities and assessments. It is not required that
you understand the configuration in order to
enable OSPF routing on the Layer 3 switch.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 24
Inter-VLAN Routing using Layer 3 Switches
Routing Configuration on a Layer 3 Switch
Complete the following steps to configure D1 to route with R1:
• Step 1. Configure the routed port. Use the no switchport command to convert the port to a routed
port, then assign an IP address and subnet mask. Enable the port.
• Step 2. Enable routing. Use the ip routing global configuration command to enable routing.
• Step 3. Configure routing. Use an appropriate routing method. In this example, Single-Area
OSPFv2 is configured
• Step 4. Verify routing. Use the show ip route command.
• Step 5. Verify connectivity. Use the ping command to verify reachability.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 25
4.4 Troubleshoot Inter-VLAN
Routing

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 26
Troubleshoot Inter-VLAN Routing
Common Inter-VLAN Issues
There are a number of reasons why an inter-VAN configuration may not work. All are related to
connectivity issues. First, check the physical layer to resolve any issues where a cable might be
connected to the wrong port. If the connections are correct, then use the list in the table for other
common reasons why inter-VLAN connectivity may fail.
Issue Type How to Fix How to Verify

show vlan [brief]

•Create (or re-create) the VLAN if it does not exist.
Missing VLANs show interfaces switchport
•Ensure host port is assigned to the correct VLAN.
ping
•Ensure trunks are configured correctly. show interface trunk
Switch Trunk Port Issues
•Ensure port is a trunk port and enabled. show running-config
•Assign correct VLAN to access port.
show interfaces switchport
•Ensure port is an access port and enabled.
Switch Access Port Issues show running-config interface
•Host is incorrectly configured in the wrong
ipconfig
subnet.
•Router subinterface IPv4 address is incorrectly
Router Configuration show ip interface brief
configured.
Issues show interfaces
•Router subinterface is assigned to the VLAN ID.
© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 27
Troubleshoot Inter-VLAN Routing
Troubleshoot Inter-VLAN Routing Scenario

Examples of some of these inter-VLAN routing

problems will now be covered in more detail.
This topology will be used for all of these
issues.

Router R1 Subinterfaces

Subinterface VLAN IP Address

G0/0/0.10 10 192.168.10.1/24

G0/0/0.20 20 192.168.20.1/24

G0/0/0.30 99 192.168.99.1/24

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 28
Troubleshoot Inter-VLAN Routing
Missing VLANs
An inter-VLAN connectivity issue could be
caused by a missing VLAN. The VLAN could be
missing if it was not created, it was accidently
deleted, or it is not allowed on the trunk link.

When a VLAN is deleted, any ports assigned to

that VLAN become inactive. They remain
associated with the VLAN (and thus inactive)
until you assign them to a new VLAN or
recreate the missing VLAN. Recreating the
missing VLAN would automatically reassign the
hosts to it.

Use the show interface interface-

id switchport command to verify the VLAN
membership of the port.
© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 29
Troubleshoot Inter-VLAN Routing
Switch Trunk Port Issues
Another issue for inter-VLAN routing includes misconfigured switch ports. In a legacy inter-
VLAN solution, this could be caused when the connecting router port is not assigned to the
correct VLAN.
However, with a router-on-a-stick solution, the most common cause is a misconfigured trunk
port.
• Verify that the port connecting to the router is correctly configured as a trunk link using
the show interface trunk command.
• If that port is missing from the output, examine the configuration of the port with the
show running-config interface X command to see how the port is configured.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 30
Troubleshoot Inter-VLAN Routing
Switch Access Port Issues
When a problem is suspected with a switch
access port configuration, use verification
commands to examine the configuration and
identify the problem.

A common indicator of this issue is the PC

having the correct address configuration (IP
Address, Subnet Mask, Default Gateway), but
being unable to ping its default gateway.
• Use the show vlan brief, show interface
X switchport or show running-config
interface X command to verify the
interface VLAN assignment.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 31
Troubleshoot Inter-VLAN Routing
Router Configuration Issues
Router-on-a-stick configuration problems are usually related to subinterface
misconfigurations.
• Verify the subinterface status using the show ip interface brief command.
• Verify which VLANs each of the subinterfaces is on. To do so, the show
interfaces command is useful but it generates a great deal of additional unrequired
output. The command output can be reduced using IOS command filters. In this
example, use the include keyword to identify that only lines containing the letters
“Gig” or “802.1Q”

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 32