Safety Data Sheet

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

Havoline Motor Oil SAE 5W-20, 5W-30, 10W-30, 10W-40, 20W-50, 30, 40
Product Use: Automotive Engine Oil
Product Number(s): 223391, 223392, 223393, 223394, 223395, 223396, 223397
Company Identification
Chevron Canada Limited
500 - 5th Ave. SW
Calgary, ALBERTA T2P 0L7
Canada
www.chevronlubricants.com

Transportation Emergency Response

CHEMTREC: (800) 424-9300 or (703) 527-3887
Health Emergency
Chevron Emergency Information Center: Located in the USA. International collect calls accepted. (800)
231-0623 or (510) 231-0623
Product Information
email : [email protected]
Product Information: (800) LUBE TEK

SECTION 2 HAZARDS IDENTIFICATION

CLASSIFICATION: Not classified as hazardous according to Canada regulatory guidelines.

_____________________________________________________________________

1 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
 SECTION 3 COMPOSITION/ INFORMATION ON INGREDIENTS

COMPONENTS CAS NUMBER AMOUNT

Highly refined mineral oil (C15 - C50) Mixture 70 - 99 %weight
Information on ingredients that are considered Controlled Products and/or that appear on the WHMIS
Ingredient Disclosure List (IDL) is provided as required by the Canadian Hazardous Products Act (HPA,
Sections 13 and 14). Ingredients considered hazardous under the OSHA Hazard Communication
Standard, 29 CFR 1910.1200, are also listed. See Section 15 for additional regulatory information.

SECTION 4 FIRST AID MEASURES

Description of first aid measures

Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and
flush eyes with water.
Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if
contaminated. To remove the material from skin, use soap and water. Discard contaminated clothing and
shoes or thoroughly clean before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get
medical advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air,
move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs.

Most important symptoms and effects, both acute and delayed

IMMEDIATE HEALTH EFFECTS
Eye: Not expected to cause prolonged or significant eye irritation.
Skin: Contact with the skin is not expected to cause prolonged or significant irritation. Contact with the skin
is not expected to cause an allergic skin response. Not expected to be harmful to internal organs if
absorbed through the skin.
Ingestion: Not expected to be harmful if swallowed.
Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause
respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at
airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation
may include coughing and difficulty breathing.

Indication of any immediate medical attention and special treatment needed Not Applicable

SECTION 5 FIRE FIGHTING MEASURES

_____________________________________________________________________

2 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish
flames.

PROTECTION OF FIRE FIGHTERS:

Fire Fighting Instructions: This material will burn although it is not easily ignited. See Section 7 for proper
handling and storage. For fires involving this material, do not enter any enclosed or confined fire space
without proper protective equipment, including self-contained breathing apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne
solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds
will be evolved when this material undergoes combustion.

SECTION 6 ACCIDENTAL RELEASE MEASURES

Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.

Spill Management: Stop the source of the release if you can do it without risk. Contain release to prevent
further contamination of soil, surface water or groundwater. Clean up spill as soon as possible, observing
precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as applying
non-combustible absorbent materials or pumping. Where feasible and appropriate, remove contaminated
soil. Place contaminated materials in disposable containers and dispose of in a manner consistent with
applicable regulations.
Reporting: Report spills to local authorities as appropriate or required.

SECTION 7 HANDLING AND STORAGE

General Handling Information: Avoid contaminating soil or releasing this material into sewage and
drainage systems and bodies of water.
Precautionary Measures: Keep out of the reach of children.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this
material. To minimize this hazard, bonding and grounding may be necessary but may not, by themselves,
be sufficient. Review all operations which have the potential of generating and accumulating an
electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash filling, tank
cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and
use appropriate mitigating procedures.
Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty
container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid,
and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode and
cause injury or death. Empty containers should be completely drained, properly closed, and promptly
returned to a drum reconditioner or disposed of properly.

SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION

_____________________________________________________________________

3 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
GENERAL CONSIDERATIONS:
Consider the potential hazards of this material (see Section 2), applicable exposure limits, job activities,
and other substances in the work place when designing engineering controls and selecting personal
protective equipment. If engineering controls or work practices are not adequate to prevent exposure to
harmful levels of this material, the personal protective equipment listed below is recommended. The user
should read and understand all instructions and limitations supplied with the equipment since protection is
usually provided for a limited time or under certain circumstances.

ENGINEERING CONTROLS:
Use in a well-ventilated area.

PERSONAL PROTECTIVE EQUIPMENT

Eye/Face Protection: No special eye protection is normally required. Where splashing is possible, wear
safety glasses with side shields as a good safety practice.
Skin Protection: No special protective clothing is normally required. Where splashing is possible, select
protective clothing depending on operations conducted, physical requirements and other substances in the
workplace. Suggested materials for protective gloves include: 4H (PE/EVAL), Silver Shield, Viton, Nitrile
Rubber.
Respiratory Protection: No respiratory protection is normally required.
If user operations generate an oil mist, determine if airborne concentrations are below the occupational
exposure limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection
from the measured concentrations of this material. For air-purifying respirators use a particulate cartridge.
Use a positive pressure air-supplying respirator in circumstances where air-purifying respirators may not
provide adequate protection.
Occupational Exposure Limits:

Component Country/ TWA STEL Ceiling Notation

Agency
Highly refined mineral oil (C15 - ACGIH 5 mg/m3 10 mg/m3 -- --
C50)
No applicable occupational exposure limits exist for this material or its components. NOTE ON
OCCUPATIONAL EXPOSURE LIMITS: Consult local authorities for acceptable provincial values in
Canada. Consult the Canadian Standards Association Standard Z94.4-2011 Selection, Use and Care of
Respirators.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Attention: the data below are typical values and do not constitute a specification.

Color: Amber
Physical State: Liquid
Odor: Petroleum odor
Odor Threshold: No data available

_____________________________________________________________________

4 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
pH: Not Applicable
Vapor Pressure: <0.01 mmHg @ 37.8 °C (100 °F)
Vapor Density (Air = 1): >1
Initial Boiling Point: 315°C (599°F) (Estimated)
Solubility: Soluble in hydrocarbons; insoluble in water
Freezing Point: Not Applicable
Melting Point: No data available
Density: 0.88 kg/l @ 15°C (59°F) (Typical)
Viscosity: 7.60 mm2/s - 17.10 mm2/s @ 100°C (212°F)
Evaporation Rate: No data available
Decomposition temperature: No data available
Octanol/Water Partition Coefficient: No data available

FLAMMABLE PROPERTIES:
Flammability (solid, gas): No Data Available

Flashpoint: (Cleveland Open Cup) 200 °C (392 °F) Minimum

Autoignition: No data available
Flammability (Explosive) Limits (% by volume in air): Lower: Not Applicable Upper: Not Applicable

SECTION 10 STABILITY AND REACTIVITY

Reactivity: May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides,
etc.
Chemical Stability: This material is considered stable under normal ambient and anticipated storage and
handling conditions of temperature and pressure.
Incompatibility With Other Materials: Not applicable
Hazardous Decomposition Products: None known (None expected)
Hazardous Polymerization: Hazardous polymerization will not occur.
Sensitivity to Mechanical Impact: No.

SECTION 11 TOXICOLOGICAL INFORMATION

Information on toxicological effects

Serious Eye Damage/Irritation: The eye irritation hazard is based on evaluation of data for product
components.

Skin Corrosion/Irritation: The skin irritation hazard is based on evaluation of data for product components.

Skin Sensitization: The skin sensitization hazard is based on evaluation of data for product components.

Acute Dermal Toxicity: The acute dermal toxicity hazard is based on evaluation of data for product
components.

Acute Oral Toxicity: The acute oral toxicity hazard is based on evaluation of data for product components.

_____________________________________________________________________

5 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
Acute Inhalation Toxicity: The acute inhalation toxicity hazard is based on evaluation of data for product
components.For additional information on the acute toxicity of the components, call the technical
information center.
Acute Toxicity Estimate: Not Determined

Germ Cell Mutagenicity: The hazard evaluation is based on data for components or a similar material.

Carcinogenicity: The hazard evaluation is based on data for components or a similar material.

Reproductive Toxicity: The hazard evaluation is based on data for components or a similar material.

Specific Target Organ Toxicity - Single Exposure: The hazard evaluation is based on data for components
or a similar material.

Specific Target Organ Toxicity - Repeated Exposure: The hazard evaluation is based on data for
components or a similar material.

ADDITIONAL TOXICOLOGY INFORMATION:

During use in engines, contamination of oil with low levels of cancer-causing combustion products occurs.
Used motor oils have been shown to cause skin cancer in mice following repeated application and
continuous exposure. Brief or intermittent skin contact with used motor oil is not expected to have serious
effects in humans if the oil is thoroughly removed by washing with soap and water.
This product contains petroleum base oils which may be refined by various processes including severe
solvent extraction, severe hydrocracking, or severe hydrotreating. None of the oils requires a cancer
warning under the OSHA Hazard Communication Standard (29 CFR 1910.1200). These oils have not
been listed in the National Toxicology Program (NTP) Annual Report nor have they been classified by the
International Agency for Research on Cancer (IARC) as; carcinogenic to humans (Group 1), probably
carcinogenic to humans (Group 2A), or possibly carcinogenic to humans (Group 2B).
These oils have not been classified by the American Conference of Governmental Industrial Hygienists
(ACGIH) as: confirmed human carcinogen (A1), suspected human carcinogen (A2), or confirmed animal
carcinogen with unknown relevance to humans (A3).

SECTION 12 ECOLOGICAL INFORMATION

ECOTOXICITY
This material is not expected to be harmful to aquatic organisms.
The product has not been tested. The statement has been derived from the properties of the individual
components.

MOBILITY
No data available.

PERSISTENCE AND DEGRADABILITY

_____________________________________________________________________

6 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
This material is not expected to be readily biodegradable. The biodegradability of this material is based on
an evaluation of data for the components or a similar material.
The product has not been tested. The statement has been derived from the properties of the individual
components.

POTENTIAL TO BIOACCUMULATE
Bioconcentration Factor: No data available.
Octanol/Water Partition Coefficient: No data available

SECTION 13 DISPOSAL CONSIDERATIONS

Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil
recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent
with applicable regulations. Contact your sales representative or local environmental or health authorities
for approved disposal or recycling methods. (See B.C. Reg. GY/92 Waste Management Act; R.R.O. 1990,
Reg. 347 General-Waste Management; C.C.SM.c. W40 The Waste Reduction and Prevention Act; N.S.
Reg. 51/95 and N.S. Reg. 179/96 for examples of Provincial legislation.)

SECTION 14 TRANSPORT INFORMATION

The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous
Goods Regulations, for additional description requirements (e.g., technical name) and mode-specific or
quantity-specific shipping requirements.

TC Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT UNDER

TRANSPORT CANADA (TDG)

IMO/IMDG Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER THE IMDG CODE

ICAO/IATA Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER ICAO

DOT Shipping Description: NOT REGULATED AS A HAZARDOUS MATERIAL UNDER 49 CFR

SECTION 15 REGULATORY INFORMATION

REGULATORY LISTS SEARCHED:

01-1=IARC Group 1
01-2A=IARC Group 2A
01-2B=IARC Group 2B
35=WHMIS IDL

_____________________________________________________________________

7 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
No components of this material were found on the regulatory lists above.

CHEMICAL INVENTORIES:
All components comply with the following chemical inventory requirements: AICS (Australia), DSL
(Canada), EINECS (European Union), ENCS (Japan), KECI (Korea), PICCS (Philippines), TSCA (United
States).

SECTION 16 OTHER INFORMATION

REVISION STATEMENT: This revision updates the following sections of this Material Safety Data Sheet:
1-16
Revision Date: MARCH 22, 2016

ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:

TLV - Threshold Limit Value TWA - Time Weighted Average
STEL - Short-term Exposure Limit PEL - Permissible Exposure Limit
GHS - Globally Harmonized System CAS - Chemical Abstract Service Number
ACGIH - American Conference of Governmental IMO/IMDG - International Maritime Dangerous Goods
Industrial Hygienists Code
API - American Petroleum Institute SDS - Safety Data Sheet
WHMIS - Workplace Hazardous Materials NFPA - National Fire Protection Association (USA)
Information System
DOT - Department of Transportation (USA) NTP - National Toxicology Program (USA)
IARC - International Agency for Research on OSHA - Occupational Safety and Health Administration
Cancer
NCEL - New Chemical Exposure Limit EPA - Environmental Protection Agency
SCBA - Self-Contained Breathing Apparatus

Prepared according to WHMIS 2015 by Chevron Energy Technology Company, 6001 Bollinger Canyon
Road San Ramon, CA 94583.

The above information is based on the data of which we are aware and is believed to be correct as of
the date hereof. Since this information may be applied under conditions beyond our control and with
which we may be unfamiliar and since data made available subsequent to the date hereof may
suggest modifications of the information, we do not assume any responsibility for the results of its use.
This information is furnished upon condition that the person receiving it shall make his own
determination of the suitability of the material for his particular purpose.

_____________________________________________________________________

8 of 8 Havoline Motor Oil SAE 5W-20, 5W-30,

Revision Number: 5
10W-30, 10W-40, 20W-50, 30, 40
Revision Date: MARCH 22, 2016 SDS : 17808CAN
Visit SCL http://shop.sclubricants.com/havoline-mo-sae-10w-40