2.

Soldering the headers

Before using your click board™, make sure

to solder 1x8 male headers to both left
and right side of the board. Two 1x8 male
headers are included with the board in
the package.
1

Bluetooth2 click
2 3
4. Essential features
1. Introduction
Bluetooth2 Click™ with it’s WT41 contains all
the necessary elements from Bluetooth® radio
to antenna and fully implemented protocol
stack. It is equipped with iWRAP firmware
which enables users to access Bluetooth®
functionality with simple ASCII commands
Turn the board upside down so that Turn the board upward again. Make sure delivered to the module. It is ideal for
bottom side is facing you upwards. Place to align the headers so that they are developers who want to integrate Bluetooth®
shorter parts of the header pins in both perpendicular to the board, then solder the wireless protocol with limited knowledge of
soldering pad locations. pins carefully. Bluetooth® and RF technologies. The board is
optimized for long range applications.

Bluetooth2 Click™ is an accessory board

click
in mikroBUS™ form factor. It’s a compact 3. Plugging the board in
and easy solution for adding bluetooth
module to your design. It features Once you have soldered the headers your
BLUEGIGA WT41 Bluetooth® 2.1 with EDR
module. Bluetooth2 Click™ communicates
board is ready to be placed into desired
mikroBUS™ socket. Make sure to align the BOARD
www.mikroe.com
with the target board microcontroller via cut in the lower-right part of the board
mikroBUS™ UART (Tx, Rx), SPI (MOSI, with the markings on the silkscreen at the
Bluetooth2 click Manual
MISO, SCK, CS), SDA, SCL, RST, AN, INT and mikroBUS™ socket. If all of the pins are ver. 1.00

PWM lines. The board is designed to use aligned correctly, push the board all
3.3V power supply only. LED diode (GREEN) the way into the socket.
indicates the presence of power supply. 0 100000 023372
5. Bluetooth2 Click™ Board Schematic 6. SMD jumpers
The Bluetooth2 Click™ board
uses four UART interface
lines. Two of them are for data
transfer between WT41 module and main
board microcontroller (Tx and Rx) and other
two are for hardware flow control (CTS and
RTS). If you want to use CTS and RTS lines,
solder two zero-ohm SMD jumpers J1 and J2.
They are not soldered by default.

VCC-3.3 7. Code Examples

CS
SCK
TX

SDI
AIO

PIO7
PIO6
RST
SDO
VCC-3.3 Once you have done all the necessary
51
50

49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
U1
AIO
AN PWM
PIO7 CTSb
J1
preparations, it’s time to get your click
53 30 RST PIO6 CTS
VCC-3.3 RST INT
VCC-3.3 VCC-3.3 VCC-3.3 VCC-3.3
54
55
29
28
CS
SCK
CS TX
TX
RX
board up and running. We have provided
R1 SCK RX
2K2
56
57
BLUEGIGA WT41
27
26
SDO
SDI MISO SCL
RTSb
CTSb RTSb
J2 the examples for mikroC, mikroBasic and
C1 C2 E1 C3 MOSI SDA
58 25 RTS
100nF 100nF 10uF 2.2uF
59 24
+3.3V +5V mikroPascal compilers on our Libstock
LD1 GND GND
R3
MIKROBUS DEVICE CONN. 1K website. Just download them and you are
ready to start.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
VCC-3.3
1K
CTS

RTS
R2
RX

.com

8. Support

MikroElektronika offers Free Tech Support

(www.mikroe.com/esupport) until the
end of product lifetime, so if something goes
wrong, we are ready and willing to help!

MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document.
Specification and information contained in the present schematic are subject to change at any time without notice. Copyright © 2013 MikroElektronika. All rights reserved.