3-4170-7-1617181789 - OSEC Manual

B1-150
OSEC® SYSTEM
BOOK NO. IM 85.010AA UA ISSUE C

B1-150 OSEC® SYSTEM
EQUIPMENT SERIAL NO. _________________
DATE OF START-UP _____________________
START-UP BY ___________________________
Prompt service available from nationwide authorized service contractors.
ORDERING INFORMATION
In order for us to fill your order immediately and correctly, please order material by description and part number, as shown
in this book. Also, please specify the serial number of the equipment on which the parts will be installed.
WARRANTY
Seller warrants for a period of one year after shipment that the equipment or material of its manufacture is free from defects
in workmanship and materials. Corrosion or other decomposition by chemical action is specifically excluded as a defect
covered hereunder, except this exclusion shall not apply to chlorination equipment. Seller does not warrant (a) damage
caused by use of the items for purposes other than those for which they were designed, (b) damage caused by unauthorized
attachments or modifications, (c) products subject to any abuse, misuse, negligence or accident, (d) products where parts
not made, supplied, or approved by Seller are used and in the sole judgement of the Seller such use affects the products’
performance, stability or reliability, and (e) products that have been altered or repaired in a manner in which, in the sole
judgement of Seller, affects the products’ performance, stability or reliability. SELLER MAKES NO OTHER WARRANTY OF
ANY KIND, AND THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR OF FITNESS OF THE MATERIAL OR EQUIPMENT FOR
ANY PARTICULAR PURPOSE EVEN IF THAT PURPOSE IS KNOWN TO SELLER. If Buyer discovers a defect in material
or workmanship, it must promptly notify Seller in writing; Seller reserves the right to require the return of such defective parts
to Seller, transportation charges prepaid, to verify such defect before this warranty is applicable. In no event shall such
notification be received by Seller later than 13 months after the date of shipment. No action for breach of warranty shall be
brought more than 15 months after the date of shipment of the equipment or material.
LIMITATION OF BUYER’S REMEDIES. The EXCLUSIVE REMEDY for any breach of warranty is the replacement f.o.b.
shipping point of the defective part or parts of the material or equipment. Any equipment or material repaired or replaced
under warranty shall carry the balance of the original warranty period, or a minimum of three months. Seller shall not be
liable for any liquidated, special, incidental or consequential damages, including without limitation, loss of profits, loss of
savings or revenue, loss of use of the material or equipment or any associated material or equipment, the cost of substitute
material or equipment, claims of third parties, damage to property, or goodwill, whether based upon breach of warranty,
breach of contract, negligence, strict tort, or any other legal theory; provided, however, that such limitation shall not apply to
claims for personal injury.
Statements and instructions set forth herein are based upon the best information and practices known to U.S. Filter/Wallace
& Tiernan, Inc., but it should not be assumed that every acceptable safety procedure is contained herein. Of necessity this
company cannot guarantee that actions in accordance with such statements and instructions will result in the complete
elimination of hazards and it assumes no liability for accidents that may occur.
WALLACE & TIERNAN PRODUCTS

1901 West Garden Road, Vineland, NJ 08360
IM 85.010AA UA (C/3-01) 1.010-42D

INTRODUCTION
The OSEC® (On Site Electrolytic Chlorination) hypochlorite generation

equipment described in this manual is designed for the continuous pro-
duction of sodium hypochlorite from brine. The sodium hypochlorite is
used in the disinfection of water supplies, being an alternative to the use
of gaseous chlorination. The sodium hypochlorite produced by the OSEC
method is of much lower concentration than normal commercial supplies
and is thus far less hazardous to handle and is not subject to the same
degree of decomposition.
This manual describes the B1-150 OSEC system, producing outputs of

between 46.3 and 147.7 lbs/day (21 and 67 kg/day) of equivalent chlorine.
The manual has been produced to enable the user to obtain the maximum
service from the equipment and comprises a full system description, in-
cluding installation, operation, maintenance, and spare parts information.
The electro-chlorinator and the associated equipment that form the system
are under the control of a separate, programmable logic controller (PLC)-
based panel, described in Supplement 1, 2, or 3, depending on your con-
figuration.
U.S. Filter/Wallace & Tiernan’s (USF/W&T) guarantee is conditional

upon the equipment being used in accordance with the instructions herein
and it is therefore recommended that these instructions be read and fully
understood before the equipment is placed in service.
WARNING: TO PREVENT POSSIBLE PERSONAL INJURY OR

! DAMAGE TO EQUIPMENT, THIS EQUIPMENT SHOULD BE
INSTALLED, OPERATED, AND SERVICED BY TRAINED,
QUALIFIED PERSONNEL WHO ARE THOROUGHLY FAMIL-
IAR WITH THE ENTIRE CONTENTS OF THIS INSTRUCTION
BOOK AND SAFETY PROCEDURES.
NOTE: When ordering material, always specify model and serial

number of apparatus.
IM 85.010AA UA (C/3-01) Introd.

Table of Contents
Very Important Safety Precautions ........................... SP-1,-2,-3

Notes on Protective Equipment and Clothing .......... 1.010-6
Anode Warranty Conditions ..................................... AW-1
Regional Offices ....................................................... 1.010-1
Technical Data .......................................................... Section 1
Installation ................................................................ Section 2
Operation .................................................................. Section 3
Service ...................................................................... Section 4
Illustrations ............................................................... Section 5
Spare Parts List ......................................................... Section 6
Additional Literature ................................................ Section 7
OSEC Control Panel .............................................. Supplement 1
IM 85.010AA UA (C/3-01) Introd. (Cont’d)

VERY IMPORTANT SAFETY PRECAUTIONS
This page provides important safety precautions to be considered during the installation, operation, and
maintenance of this equipment.
WARNING
HYDROCHLORIC ACID
HYDROCHLORIC ACID IS USED FOR ACID CLEANING THE ELECTRODES OF THE ELECTRO-
CHLORINATOR AS PART OF THE LONG-TERM SERVICING PROCEDURES. THE STORAGE
OF ANY ACID AND THE RELEVANT HANDLING FACILITIES MUST BE COMPLETELY SEPA-
RATE FROM THE SODIUM HYPOCHLORITE FACILITIES. HYDROCHLORIC ACID FUMES
EXCESSIVELY IN ITS CONCENTRATED FORM AND GREAT CARE MUST BE TAKEN WHEN
HANDLING CARBOYS OF ACID. EVERY POSSIBLE SAFEGUARD MUST BE TAKEN TO
ENSURE THAT THE ACID DOES NOT COME INTO CONTACT WITH THE HYPOCHLORITE
SOLUTION AS THIS WILL RESULT IN CHLORINE GAS BEING PRODUCED. ANY SPILLAGE
OF ACID, WHETHER DILUTE OR NOT, SHOULD BE IMMEDIATELY FLUSHED AWAY WITH
COPIOUS QUANTITIES OF WATER.
PERSONNEL MUST BE MADE AWARE OF THE DANGERS OF HANDLING CONCENTRATED

ACID AND THE PREPARATION OF DILUTE SOLUTIONS. THE PERSONNEL MUST WEAR
CHEMICAL GOGGLES, PROTECTIVE CLOTHING, RUBBER BOOTS, AND GLOVES. SPLASHES
IN THE EYES MUST BE DEALT WITH IMMEDIATELY BY PROLONGED IRRIGATION WITH
RUNNING WATER. MEDICAL ADVICE SHOULD BE SOUGHT AS SOON AS POSSIBLE. SIMI-
LARLY, SPLASHES TO THE SKIN OR CLOTHING SHOULD ALSO BE IMMEDIATELY WASHED
IN RUNNING WATER. WARNING NOTICES POINTING OUT THE DANGERS AND DISPLAY-
ING THE PREVIOUS POINTS SHOULD BE PROMINENTLY POSTED WHEREVER ACID IS
STORED OR HANDLED.
SODIUM HYPOCHLORITE
THE STRENGTH OF THE HYPOCHLORITE SOLUTION GENERATED BY THE OSEC UNIT

AND STORED IN THE BULK TANK IS APPROXIMATELY 0.8% W/W. ALTHOUGH THIS SO-
LUTION IS CONSIDERABLY WEAKER THAN NORMAL COMMERCIAL BULK SUPPLIES (15%
W/W), CARE SHOULD STILL BE TAKEN WITH HANDLING. THE SODIUM HYPOCHLORITE
IS SLIGHTLY ALKALINE AND FORMS AN OXIDIZING AND BLEACHING AGENT THAT IS
CORROSIVE AND MAY CAUSE DAMAGE TO SKIN AND CLOTHING ON CONTACT.
MIXING OF THE CHEMICAL WITH ANY FORM OF ACID MUST BE AVOIDED AS HIGHLY
TOXIC CHLORINE GAS WOULD BE GENERATED. WARNING NOTICES SIMILAR TO THOSE
DISPLAYED FOR THE ACID EQUIPMENT SHOULD BE PROMINENTLY POSTED IN AREAS
WHERE HYPOCHLORITE IS GENERATED AND STORED.
IM 85.010AA UA (C/3-01) SP-1

VERY IMPORTANT SAFETY PRECAUTIONS (CONT’D)
ELECTRICAL SAFETY
THE ELECTRICAL POWER IN THIS EQUIPMENT IS AT A VOLTAGE HIGH ENOUGH TO

ENDANGER LIFE. BEFORE CARRYING OUT MAINTENANCE OR REPAIR, PERSONS CON-
CERNED MUST ENSURE THAT THE EQUIPMENT IS ISOLATED FROM THE ELECTRICAL
SUPPLY AND TESTS MADE TO VERIFY THAT THE ISOLATION IS COMPLETE.
WHEN SUPPLIES CANNOT BE DISCONNECTED, FUNCTIONAL TESTING, MAINTENANCE

AND REPAIR OF THE ELECTRICAL UNITS IS TO BE UNDERTAKEN ONLY BY PERSONS
FULLY AWARE OF THE DANGER, AND WHO HAVE TAKEN ADEQUATE PRECAUTIONS.
HYDROGEN GAS
THE PROCESS OF CONVERTING BRINE INTO SODIUM HYPOCHLORITE GENERATES HY-

DROGEN GAS, WHICH IS SAFELY EXHAUSTED TO ATMOSPHERE AT THE EXTERNAL
HYPOCHLORITE STORAGE TANKS, HAVING BEEN DILUTED WITH AIR TO REDUCE ITS
CONCENTRATION. HOWEVER, TO ENSURE PLANT SAFETY, WARNING NOTICES SHOULD
BE DISPLAYED FORBIDDING SMOKING OR ANY OPEN FLAME IN THE VICINITY OF THE
STORAGE TANKS. THE EQUIPMENT SHOULD BE REGULARLY CHECKED TO ENSURE
THAT NO GAS LEAKAGES OCCUR. DO NOT CHECK WITH A MATCH OR OPEN LIGHT. USE
A SPECIFIC SENSITIVE HYDROGEN DETECTOR.
NO ATTEMPT MUST BE MADE TO EXTRACT SODIUM HYPOCHLORITE AT ANY POINT

PRIOR TO THE STORAGE TANK, APART FROM SMALL VOLUME SAMPLES TAKEN AT THE
HYPOCHLORITE OUTLET SAMPLE VALVE FOR PURELY ANALYTICAL PURPOSES. THIS IS
TO PREVENT THE HYDROGEN, WHICH IS CONTAINED IN THE HYPOCHLORITE BEFORE
REACHING THE TANK, FROM BEING RELEASED INTO THE ATMOSPHERE IN AN UNDI-
LUTED FORM, WITH CONSEQUENT RISK OF IGNITION.
GENERAL
TO AVOID POSSIBLE SEVERE PERSONAL INJURY OR EQUIPMENT DAMAGE, OBSERVE

THE FOLLOWING:
TO ENSURE PROPER AND SAFE OPERATION OF THIS EQUIPMENT, USE ONLY U.S. FILTER
LISTED PARTS, EXCEPT FOR COMMERCIALLY AVAILABLE PARTS AS IDENTIFIED BY
COMPLETE DESCRIPTION ON ACCOMPANYING PARTS LIST. THE USE OF UNLISTED PARTS
CAN RESULT IN EQUIPMENT MALFUNCTIONS, CAUSING POSSIBLE SEVERE PERSONAL
INJURY.
THIS EQUIPMENT SHOULD BE INSTALLED, OPERATED, AND SERVICED ONLY BY TRAINED

QUALIFIED PERSONNEL WHO ARE THOROUGHLY FAMILIAR WITH THE ENTIRE CON-
TENTS OF THE INSTRUCTION BOOK PROVIDED.
IM 85.010AA UA (C/3-01) SP-2
VERY IMPORTANT SAFETY PRECAUTIONS (CONT’D)
DO NOT DISCARD THIS INSTRUCTION BOOK UPON COMPLETION OF INSTALLATION.

INFORMATION PROVIDED IS ESSENTIAL FOR PROPER AND SAFE OPERATION AND MAIN-
TENANCE.
ADDITIONAL OR REPLACEMENT COPIES OF THIS INSTRUCTION BOOK ARE AVAILABLE

FROM:
USFILTER’S WALLACE & TIERNAN PRODUCTS

1901 W. GARDEN ROAD
VINELAND, NEW JERSEY 08360
PHONE: (856) 507-9000
FAX: (856) 507-4125
____________________________________________________________________________________
NOTE
Minor part number changes may be incorporated into USF/W&T products from time to time that are not
immediately reflected in the instruction book. If such a change has apparently been made in your equip-
ment and does not appear to be reflected in your instruction book, contact your local USF/W&T sales
office for information.
Please include the equipment serial number in all correspondence. It is essential for effective commu-
nication and proper equipment identification.
IM 85.010AA UA (C/3-01) SP-3

NOTES ON PROTECTIVE EQUIPMENT AND CLOTHING
The following Warning appears in several locations in this book. It is general in nature due to the
variety of hazardous liquids this equipment is capable of handling.
WARNING: WHEN DEALING WITH HAZARDOUS MATERIAL, IT

IS THE RESPONSIBILITY OF THE EQUIPMENT USER TO OBTAIN
AND FOLLOW ALL SAFETY PRECAUTIONS RECOMMENDED BY
THE MATERIAL MANUFACTURER/SUPPLIER.
It is good general practice to make use of 1. Goggles, flexible

protective equipment when handling any fitting, hooded ventila-
tion
hazardous material. (per ANSI Z87.1)
2. Face Shield
IT IS RECOMMENDED THAT SUCH
(per ANSI Z87.1)
PROTECTIVE EQUIPMENT BE USED
BY ALL PERSONS SERVICING THIS
3. Chemical Apron
PUMP, ASSOCIATED PIPING, TUBING,
VALVES, AND ACCESSORIES, WHEN
THE EQUIPMENT IS HANDLING ANY 4. Chemical Gloves
HAZARDOUS MATERIAL.
NOTE: (1) ANSI Z87.1 “practice for occupational.......eye and face protection” recommends goggles
(#1 above) as the “preferred protection” when handling chemicals that present a hazard
from splash, acid burns or fumes; for severe exposure, a face shield (#2 above) over the
goggles is recommended.
(2) An eye flushing fountain and a deluge-type shower may be recommended or required by
insurance carriers or governmental safety agencies, which should be consulted for spe-
cific requirements.
IM 85.010AA UA (C/3-01) 1.010-6C

ANODE WARRANTY CONDITIONS
The anodes used in the electro-chlorinator are warranted for five calendar years after installation and commissioning
unless stated otherwise at the time of tender or unless there is a temperature variance as mentioned under item a,
below.
USF/W&T will replace or refurbish the anodes during the period after installation and commissioning, either option
at the spare parts price in effect at the time of replacement, less a percentage equal to that portion of the expected life
that was not obtained from the anodes being replaced. The warranty and conditions current at the time of replacement
will then apply.
Anode life is dependent upon many factors, the warranty is therefore conditional upon correct operation of the
equipment in accordance with the Instruction Manual and subject to the following conditions:
a. A five-year warranty will apply if the temperature of the incoming electrolyte does not fall below 50°F.
b. The salinity of the electrolyte must be above 18,000 mg/l chloride (Cl2) unless otherwise specified by USF/
W&T. The sulfate (SO4) content must be less than 1/7th of the Cl2 content.
c. The manganese level in the electrolyte entering the electrolyzer must not exceed 10 ug/L at any time.
d. The electrolyte must contain less than 2 mg/l fluoride (F).
e. The electrolyzer, as specified, must not be operated at a current above the figure shown in Section 1 -
Technical Data.
f. The operational log, as shown Section 4 - Service, must be maintained with the time periods specified.
g. A monthly log of water analysis must be maintained by water authorities and, in the case of other users, as
determined by agreement with USF/W&T.
h. Salt quality must be to the following specifications:
Water insolubles: 0.01% maximum

Calcium sulfate: 0.14% maximum
Magnesium sulfate: 0.02% maximum
Magnesium chloride: 0.1% maximum
Sodium chloride: 99.82% minimum
i. Acid cleaning is to be carried out if current efficiency falls below the normal by more than five percent.
j. Protective current is to be maintained and applied according to the Instruction Manual.
k. Water hardness leaving the softener must not exceed 17 mg/l of calcium carbonate (CaCo3).
l. If it is found that the performance of the anode coatings has been impaired by organic contaminants in the
electrolyte, causing (directly or indirectly) blinding or reduced coating life, then the anode coating lifetime
guarantee will not apply.
It is recommended that the total organic content in the electrolyte should be less than 10 mg/kg, the actual
limit being dependent on the species.
m. Brine dilution shall normally be a nominal 10:1, this may be increased to a nominal 12:1, providing the
incoming electrolyte is always above 50°F (10°C).
IM 85.010AA UA (C/3-01) AW-1

REGIONAL OFFICES
INSTALLATION, OPERATION, MAINTENANCE, AND SERVICE INFORMATION
Direct any questions concerning this equipment that are not answered in the instruction book to the
Reseller from whom the equipment was purchased. If the equipment was purchased directly from
USFilter's Wallace & Tiernan Products (USF/W&T), contact the office indicated below.
UNITED STATES
1901 West Garden Road

Vineland, NJ 08360
TEL: (856) 507-9000
FAX: (856) 507-4125
CANADA
If the equipment was purchased directly from USF/W&T Canada, contact the nearest office indicated
below.
ONTARIO QUEBEC
250 Royal Crest Court 243 Blvd. Brien

Markham, Ontario Bureau 210
L3R3S1 Repentigny, Quebec
(905) 944-2800 (514) 582-4266
MEXICO
If the equipment was purchased directly from USF/W&T de Mexico, contact the office indicated be-
low.
Via Jose Lopez Portillo 321

Col. Sta. Maria Cuautepec
Tultitlan, Edo. de Mexico
54900 Mexico
TEL: 525 879 0260
FAX: 525 875 2171
IM 85.010AA UA (C/3-01) 1.010-1D

SECTION 1 - TECHNICAL DATA
List of Contents
PARA./DWG. NO.
General Description .............................................. 1.1

Water Softener ...................................................... 1.2
Salt Saturator ........................................................ 1.3
Brine Pump ........................................................... 1.4
Rectifier Unit ........................................................ 1.5
Hypochlorite Storage Tank ................................... 1.6
OSEC Electrolyzer Type B1-150 ......................... 1.7
Illustrations
Hypochlorite Storage Tank ................................. 85.010.170.030
B1-150 OSEC Electrolyzer................................. 85.010.170.010A&B
IM 85.010AA UA (C/3-01) 1
1.1 General Description
An OSEC system is designed to produce a supply of sodium hypochlorite

solution (NaOCl), which is then subsequently used in the chlorination—
for disinfection purposes—of swimming pools or potable water supplies.
The hypochlorite is generated electrolytically from a solution of brine and
softened water by an OSEC electrolyzer. The typical OSEC system shown
in Dwg. 85.010.110.010 contains essentially six main items of equip-
ment, including:
• Water Softener — Provides the softened water supply to the brine

equipment and to the electrolyzer.
• Salt Saturator — Produces the concentrated brine solution used by

the electrolyzer.
• Brine Pump — Meters the brine from the saturator to the electrolyzer.
• Electrolyzer — Generates the hypochlorite solution.
• Transformer/Rectifier Unit — Provides the low voltage/high current

DC supply to the electrolyzer to effect the electrolysis.
• Storage Tank
The water softener, salt saturator, transformer/rectifier, and storage tank

equipment are all proprietary items of other than USF/W&T manufacture.
Typical examples of these items are briefly described in the following
pages as an aid to understanding the overall system concept; however,
units of different manufacture and design may be supplied at customer
request, or may be obtained directly by the customer. For full details,
reference should be made to the manufacturers’ specific literature sup-
plied with the equipment. The brine pump is fully described in a separate
publication supplied with the pump.
The hypochlorite generation system is under the control of a dedicated

programmable logic controller-based panel, mounted remotely from the
electrolyzer. The controller responds to status signals from various plant
monitors to control the hypochlorite generation efficiently and safely.
Generation is primarily determined by the level switches at the storage

tank, starting up the generation when the low level is reached and shutting
down when the high level is reached. A manual top-up facility is provided
to override the Low Start initiation should a full tank of solution be re-
quired prior to a shut down or servicing. The panel is usually set so that
IM 85.010AA UA (C/3-01) 2
it operates primarily during off-peak electricity hours to keep generation

costs to a minimum. Overrides are built into the control system to enable
smaller volume generation facilities to prevent the level falling too low or
to fulfil an expected demand during daytime hours. For full details of the
control panel, refer to Supplement 1.
1.2 Water Softener
The saturated brine and the dilution water, which is used by the electrolyzer
to produce the sodium hypochlorite solution, must be as ‘soft’ as possible
(maximum 25 mg/l of CaC03) to eliminate the build up of deposits on the
electrolyzer electrodes during electrolysis, as these deposits would seri-
ously impair the efficiency of the OSEC unit. To provide sufficient capac-
ity for the salt saturator and the electrolyzer, a twin cylinder softener is
used. The unit operates from a main water supply and its softened water
output feeds into a common supply line to the saturator and electrolyzer.
The softener consists of two cylinders incorporating ultra-fine particle

resin beds in which the ion exchange takes place to remove the hardness
elements from the water supply. This process involves passing the water
from the main supply through a resin bed charged with sodium ions. As
the water flows through the bed, the hardness ions in the water (e.g.,
calcium and magnesium) are exchanged for the soft sodium ions attached
to the resin particles. This exchange takes place whenever water is drawn
through the softener by the demands of the saturator or electrolyzer until
the resin bed is exhausted of sodium and requires regeneration.
The two cylinders are arranged so that only one cylinder is in use at a time,
the other being left in a standby condition. When the cylinder in use nears
exhaustion, as detected by a meter unit on top of the cylinders that registers
the flow of water through the cylinder, this meter unit initiates the
changeover to the standby cylinder. While the new cylinder is in service,
the previously exhausted cylinder is automatically regenerated and left on
standby, ready for the next changeover.
This changeover from one cylinder to the other is effected by means of

water-operated servo valves. These valves, in turn, are controlled by the
meter unit atop the cylinders. The meter unit incorporates a small turbine
that spins as softened water is drawn through the cylinder, the turbine
being arranged to drive the meter. The regeneration of the exhausted resin
bed in the cylinder, when initiated by the meter, is achieved by back
flushing with brine solution, this being drawn automatically via a non-
return valve from the salt saturator unit. The brine, as it is reverse-flushed
through the resin bed, picks up the hardness elements that have been
deposited and discharges them into a convenient drain. This brine regen-
IM 85.010AA UA (C/3-01) 3
eration is followed by a back-wash with softened water to flush away any

remaining brine. The brine regeneration and back-wash cycle takes ap-
proximately 11 minutes. For a full description of the water softener, refer
to the manufacturer’s manual supplied with the equipment.
1.3 Salt Saturator
The salt saturator is sized both to suit the brine requirements of the
electrolyzer and to provide the necessary number of days of storage before
recharging, as stipulated by the customer. Each unit contains a substantial
quantity of salt arranged above a filter bed constructed from layers of
gravel. The tank is fed from the softened water supply and this water is
drawn through the salt reservoir by the action of the brine pump that feeds
the electrolyzer. As the water is drawn through the salt reservoir, it absorbs
the salt until it becomes saturated and can absorb no more material. It is
drawn from the bottom of the tank, the layers of gravel preventing any
undissolved solids from passing through to the pump. The brine outlet of
the saturator is usually fitted with a calibration column to enable the
output of the brine pump to be precisely set to meet the flow requirements
of the electrolyzer.
1.4 Brine Pump
The brine pump—or pumps, if a duty/standby pump configuration is re-

quired—that meters the brine solution from the saturator to the electrolyzer
is usually mounted remotely from the electrolyzer and is positioned near
the saturator to avoid a long suction line. A precision metering unit with
a mechanical diaphragm and adjustable stroke control is used. A percent-
age adjustment of the maximum stroke control enables the output capacity
of the pump to be precisely set to match the brine flowrate required by the
electrolyzer.
Three different capacities of pump are used, depending on the output

capacity of the electrolyzer. The pump outputs are determined by their
drive mechanisms, the smallest capacity pump having a maximum output
of 2.6 gal/hour (10 ltr/hour), this pump being used with the 46.3 lbs/day
(21 kg/day) electrolyzer. The electrolyzers with outputs between 55 and
110 lbs/day (25 and 50 kg/day) use a pump having a maximum output of
6.3 gal/hour (24 ltr/hour). The largest of the pumps, producing a maxi-
mum output of 9.2 gal/hour (35 ltr/hour), is used with electrolyzers having
outputs between 121.3 to 147.7 lbs/day (55 to 67 kg/day). The pump
discharges are fitted with pulsation dampers to smooth the pumping pulses
and thus provide a steady indication at the brine flowmeter on the
electrolyzer. Each discharge is also fitted with a pressure relief valve set
to relieve at a nominal 36psig (2.5 bar) pressure.
IM 85.010AA UA (C/3-01) 4
1.5 Transformer/Rectifier Unit
The transformer/rectifier unit is usually located in a room adjoining the

electrolyzer plant room so that it can be adequately ventilated for cooling.
This also avoids it being subject to water or chemical splashes caused when
servicing the electrolyzer. The unit comprises essentially a three-phase
step-down transformer and an air-cooled rectifier, all contained in a heavy-
duty, epoxy-coated, sheet steel cabinet. The incoming 380/440 V, 60 Hz,
three-phase supply is fed, via an isolator and contactor, to a motor-driven,
three-phase variable transformer. Each output phase of the variable trans-
former feeds the primaries of a heavy-duty, three-phase step-down trans-
former, the output phases of which are full wave rectified and combined to
provide the DC supply for electrolysis. The rectifier unit produces a voltage
of 15 V DC at a current rating to suit the size of electrolyzer supplied, the
operating currents required for the different capacities being shown in the
electrolyzer data sheet (Table 1.1, located at the end of this section).
A shunt placed in series with the positive DC output lead generates a

millivolt signal that is used not only to operate the ammeter but also to
power a constant current controller for the rectifier control circuitry. This
constant current controller processes the millivolt signal and compares it
with a reference voltage set by the output current setting potentiometer. If
the signal is outside the reference level, the controller feeds a signal to the
drive motor of the variable transformer. The motor adjusts the transformer
in the appropriate direction to vary the supply to the main step-down
transformer and thus adjust the DC output of the unit to maintain the
electrolyzer current at the set value.
The motor-driven variable transformer can be controlled either in an au-

tomatic mode using the constant current unit, as previously described, or
in a manual mode. In the manual mode the transformer is adjusted by a
Raise/Lower switch on the unit control panel. Moving the switch in the
required direction provides a supply direct to the transformer drive motor
to adjust it in the appropriate direction to change the output voltage and
so vary the output of the main transformer, as previously described. This
Raise/Lower switch is enabled only when the Auto/Man switch is in the
Manual position.
The transformer/rectifier unit front panel is equipped with an ammeter

and voltmeter to monitor the DC output. The voltmeter is fitted with pre-
settable high and low alarm contacts that are triggered if the voltage drifts
outside the normal operating voltage. These alarm contacts provide a
signal to the electrolyzer PLC control to light a specific alarm lamp and
sound an audible alarm. They also initiate the shut down of the electrolyzer
and rectifier unit.
IM 85.010AA UA (C/3-01) 5
1.6 Hypochlorite Storage Tank
The storage tank is usually sized to provide sufficient capacity for one day
of water treatment without the electrolyzer being in operation. The tank
provides the storage for the generated hypochlorite, as well as allows the
hydrogen gas contained in the newly generated solution to detrain and be
safely vented to atmosphere. This product tank must be suitable for 1%
sodium hypochlorite at a temperature up to 104°F (40°C), and is usually
manufactured from spirally wound, high-density, black polyethylene or
premium resin FRP with nexus veil. The tanks, shown in Dwg.
85.010.170.030, are closed-top designs fitted with 19-3/4-inch (500mm)
diameter access manways. The tanks are force-ventilated by external blower
assemblies, the type of arrangement used being dependent upon the size
of the electrolyzer and the customer’s specific requirements.
The normal arrangement is for the tank to be ventilated either by a single

blower assembly or a pair of blowers arranged in a duty/standby configu-
ration under PLC supervision. The particular blower arrangement is wall-
mounted or mounted on a raised base near the tank. The blowers are
unsuitable for external mounting unless located in a weather-proof enclo-
sure. Where they are located in the same room as the storage tank, their
air inlets must be piped from outside the building. The blowers are cen-
trifugal-type fans, which operate from a 110 or 240V, 60 Hz, single-phase
supply. The output from a single blower is piped in two-inch diameter
PVC ductwork to the air inlet at the top of the tank. Where a duty/standby
arrangement of blowers is provided, the individual outputs of the blowers
connect to a blower changeover device, a common outlet from the
changeover unit being piped to the air inlet at the tank. The changeover
unit incorporates a divertor flap operated by the particular blower in use
so that the pipework to the standby blower is sealed. Should the standby
blower start-up due to a failure of the duty blower, the air flow will auto-
matically changeover the divertor flap to seal the pipework to the previ-
ously operating blower.
These blower systems ensure that the hydrogen gas detraining from the
newly generated hypochlorite is diluted with sufficient air to reduce the
hydrogen concentration to less than 25% of its LEL value and so prevent
the possibility of ignition. The air flow into the tank is monitored by a
sensitive pressure differential switch that senses the change in pressure in
the pipework when the blower is in operation. The contacts of the pressure
switch are connected back to the OSEC control. In a single blower system,
should the pressure switch detect the failure of the blower, it will signal
to the PLC to shut down the generation system, also initiating an alarm.
In duty/standby blower systems, should a failure of the duty blower be
detected, the standby blower is automatically started and a specific alarm
IM 85.010AA UA (C/3-01) 6
raised. If this standby blower should subsequently fail, the generation

system will be shut down.
For internally located tanks, a simple level indication is provided at the

tank using a sight glass of clear PVC piping interconnecting the hypochlo-
rite outlet at the base of the tank and the overflow connection at the top of
the tank. This arrangement must not be used if the ambient temperature
is likely to fall below 32°F (0°C). On external tanks, a ‘cat & mouse’-type
level indicator is provided.
From the overflow connection at the top of the tank, the overflow pipework
is run to a nearby low-level overflow alarm tank fitted within an area
capable of containing the full tank capacity in the event of a major leakage,
or to a separate tank on systems without this safety measure. This overflow
tank is fitted with a float-operated level switch that is wired back to the
OSEC control to shut down the system should an overflow occur, as this
points to a failure of the normal High (Stop) level switch. The overflow
pipework is fitted with an air vent to prevent syphonic effects from emp-
tying the tank via the overflow.
Where full off-peak operation is specified, the tank contents level is trans-
mitted to the OSEC controller from a hall effect pressure transducer as a
0-20mA signal. The Operator Terminal at the OSEC control panel is used
to set the tank level parameters for both off-peak and daytime hours op-
eration.
The tank's High and Low level switches control the automatic operation
of the electrolyzer, stopping it from generating hypochlorite when the
High level is reached and starting it up again when the Low level is
reached. Where a full off-peak operational facility is provided, these level
switches are set so that the maximum quantity of hypochlorite is generated
during the low-cost electricity hours. The Low Storage level switch is set
to operate and warn when the hypochlorite level has reached a very low
point, near which the hypochlorite dosing pumps would begin to suck air
or hydrogen into the system. The PLC provides an inhibit signal to the
dosing pump control to stop any dosing pump until the hypochlorite level
has risen sufficiently.
1.7 OSEC Electrolyzer Type B1-150
The electrolyzer—also known as an electrolyzer and shown in Dwg.

85.010.170.010—consists of a fabricated base skid of mild steel plate and
channel construction on which is centrally mounted a vertical, channel
section, mild steel column. Mounted in a mid position at the rear of the
column, and arranged horizontally, is the 6-inch (150mm) diameter
IM 85.010AA UA (C/3-01) 7
electrolyzer casing in which the electrolysis of the brine takes place. At the
top rear of the column is the heat exchanger, coupled to the hypochlorite
output of the electrolyzer and to the dilution water supply, and arranged
to warm the dilution water for efficient electrolysis. On the front face of
the column is the hydraulic panel on which is mounted the various valves,
flowmeters, and controls for the brine and dilution water feeds. An infor-
mation plate attached to the panel shows the system schematically and
details the various inputs and flows.
The incoming water supply from the softener, which is switched by a skid-
mounted solenoid valve, connects initially to a manual 1/2-inch ball valve
at the base of the hydraulic panel. From this valve, the water feeds to the
UXA.93335 pressure reducing valve mounted alongside. The reducing
valve sets and maintains the correct pressure and flowrate through the
electrolyzer. After the reducing valve, the dilution water supply feeds to
the base of the water flowmeter.
This meter, calibrated to suit the size of electrolyzer, is used both as an aid
for initial setting and to continuously monitor the flowrate. The flowmeter
is fitted with presettable low flow alarm contacts that are wired to the
OSEC control panel to inhibit electrolyzer operation unless the dilution
water flow is correct.
After the flowmeter, the supply passes to a tee piece that splits the water
supply into two feeds. One feed, from the side of the tee, passes through
a Maric control valve and down the length of the hydraulic panel to feed
directly into the underside of the electrolyzer at the second cell position.
This Maric valve is fitted with an internal orifice to regulate the flow
through to the second cell to approximately 50% of the total electrolyzer
water requirements.
The other dilution supply feed from the tee connects via another similar
sized Maric control valve to a three-way manual control valve at the top
of the panel. This valve enables the dilution water supply to the first
electrolyzer cell to either flow directly to the cell, mixing with the incom-
ing brine supply en route, or be fed via the unit’s heat exchanger mounted
at the top rear of the support column. The heat exchanger utilizes the heat
of the hypochlorite as it is generated to warm the dilution water if its
temperature is too low for efficient electrolysis (minimum 44.6°F (7°C)).
The Maric valves in the two dilution water supply lines ensure that each
feed line passes approximately 50% of the water requirements. The dilu-
tion water is added to the brine solution at the two points in order to
conserve anode life and ensure a more even chemical reaction.
IM 85.010AA UA (C/3-01) 8
The brine solution is drawn from the salt saturator by the action of the
remote-mounted brine pump. This pump, which is sized to suit the
electrolyzer output capacity, is a diaphragm pump with a variable stroke
control enabling the percentage of pump maximum stroke to be altered,
and thus the output of the pump to be adjusted, to achieve the correct brine
flowrate for the electrolyzer requirements. From the pump discharge, the
brine connects to the inlet union on the hydraulic panel and then feeds to
a back pressure valve and thence to the brine flowmeter. The back pres-
sure valve ensures an accurate, consistent delivery from the pump. This
input line from the pump is also fitted with a 29-1/2-inch (750mm) high
pulse damper to smooth the output from the pump and enable a steady
reading to be obtained at the flowmeter, the flowmeter being calibrated in
percent brine flow. This flowmeter is also fitted with a presettable low
flow switch wired in series with the dilution water flowmeter switch to the
OSEC panel to inhibit electrolyzer operation unless both flows are cor-
rect. For systems using a duty/standby brine pump system, the low flow
switch is wired independently to the PLC so that, should the switch detect
the failure of the duty pump, it will automatically start up the standby
pump and raise a specific alarm. Should the standby pump fail, the system
will be shut down. From the brine flowmeter, the brine supply feeds into
a tee piece in the dilution supply feed to the first cell. This line, in which
50% of the dilution water combines with the brine, is fitted with a tem-
perature gauge calibrated from -22° to +140°F (-30° to +60°C), to monitor
the temperature of the incoming solution.
NOTE: Under the terms of the warranty on the electrodes used in the
electrolyzer, the minimum temperature of the incoming brine solu-
tion mix at which the electrolyzer is permitted to operate is 44.6°F
(7°C), this temperature being registered at the gauge previously de-
scribed. The number of occasions on which the unit may operate with
incoming solution at this minimum temperature should not exceed
two months in any 12-month period. The normal minimum solution
temperature for continuous use is 50°F (10°C).
Where the electrolyzer is under the control of the UXA.85852 control

panel, it is fitted with a low temperature sensor to provide an alarm should
the temperature of the incoming supply fall to 50°F (10°C), and a com-
plete shut down if the temperature falls below 44.6°F (7°C).
The 6-inch (150mm) diameter plastic electrolyzer casing mounted at the

rear of the central column houses the electrode assemblies (as shown in
Dwg. 85.035.160.010). The electrodes are flat, rectangular metal plates,
arranged as interleaved layers of alternate positive and negative elec-
trodes, separated from each other by small Kynar spacers. The electrodes
are arranged within the casing to form four cells. All the positive elec-
IM 85.010AA UA (C/3-01) 9
trodes (anodes)in each cell are connected together in parallel. Similarly,

all the negative electrodes (cathodes) in the cell are connected together in
parallel. Each cell within the casing is connected in series to the next cell
so that the anodes of one cell are connected to the cathodes of the next cell,
etc., as in a battery. The cells are separated from each other in the casing
by circular plastic discs that are pierced with a series of holes to allow the
free passage of solution and gas through the electrolyzer.
The number of electrodes fitted to the electrolyzer and the number of

electrodes used in each electrolyzer determine the hypochlorite produc-
tion capacity of the unit. The B1-150 electrolyzer is equipped with a single
electrolyzer and has outputs ranging from 46.3 and 147.7 lbs/day (21 and
67 kg/day) of equivalent chlorine. Refer to the B1-150 operational data
sheet (Table 1.1, located at the end of this section) for details of the various
capacities available and the number of electrodes used.
The anodes used are made from titanium and have precious metal oxide
coatings. The cathodes are made from Hastelloy C. All other metalwork
within the electrolyzer casing is titanium, which is one of the few metals
that can resist hypochlorite attack. The plastic used for the electrolyzer
casing is chlorinated polyvinyl chloride (cpvc), which is formulated to
withstand any high temperatures the casing is likely to be subject to inter-
nally, without risk of distortion.
The two ends of the four-cell electrolyzer assembly are connected to

connecting spacers through each end flange of the casing. These right- and
left-hand end terminals, being of negative and positive polarity, respec-
tively, are connected by long, flat copper bus bars to the corresponding
polarity terminals of the transformer/rectifier unit. This unit provides the
low voltage/high current DC supply for the electrolysis of the brine. The
usual arrangement is to locate the transformer/rectifier in an adjoining
room to the electrolyzer, to avoid it being subject to liquid splashes, and
then have the interconnecting bus bars feed through clearance holes in the
dividing wall. The bus bars are made of large-section, high-conductivity
copper strip, which is covered by an insulated shrink-fit sleeving. The
transformer/rectifier provides a nominal 15V DC supply at the current
required for the capacity of the electrolyzer (quoted on Table 1.1, located
at the end of this section).
As the brine solution is passed through the electrolyzer casing, it is in-

creasingly converted to sodium hypochlorite as it is electrolyzed in the
four cells. The chemical reaction also generates hydrogen gas, which
remains in the solution when it is piped away to the nearby storage tank.
Here the hydrogen gas is detrained from the solution and vented to atmo-
sphere. A temperature sensor, mounted in the top of the electrolyzer cas-
IM 85.010AA UA (C/3-01) 10
ing and wired to the OSEC control panel, signals the control to shut down
the electrolyzer should the solution temperature rise above 113°F (45°C).
The outlet manifold at the positive end of the casing is fitted with a float-
operated level switch to prevent the DC supply being applied to the elec-
trodes unless the casing is full of solution. On leaving the electrolyzer, the
warm hypochlorite solution passes through the outer tubes of the column-
mounted heat exchanger assembly. The outer tubes surround the inner
dilution water supply tubes and use the heat of the hypochlorite to raise the
temperature of the dilution water, should this be required.
The electrolyzer is also equipped with valves to enable acid cleaning

equipment to be connected when this be required as part of the servicing.
The dilution water supply to the electrolyzer should have a hardness not
exceeding 25 mg/l of CaCO3 (calcium carbonate); this often entails the
use of proprietary water softeners to remove the hardness elements. With-
out this provision, these elements would otherwise be deposited on the
electrodes during electrolysis, leading to a gradual lowering of efficiency.
Occasional breakdowns in the softeners may lead to deposits forming.
These deposits can easily be removed without dismantling the electrolyzer
by draining the unit and then flushing through with a dilute hydrochloric
acid solution using a packaged pump unit, which can be supplied. The
system used is a circulatory type where the output from the pump is
connected to the ball valve at the brine/dilution water inlet to the electrolyzer
casing, and a return pipe from the ball valve at the hypochlorite outlet
manifold is connected back to the tank. For full details, refer to the acid
cleaning instructions in Section 4 of this manual. This service can be
carried out by USF/W&T service personnel, if required.
IM 85.010AA UA (C/3-01) 11
IM 85.010AA UA (C/3-01)
Table 1.1 - B1-150 OSEC – Operational Data
Brine supply feedrate

lbs/day N umber of Inlet N ominal system power Water requirements
gal/h (liters/h)
(kg/day) water
C l2 supply Maric valve for Peak water flow
Saturate Dilution Electrolyzer Electrolyzer
* Anodes C athodes pressure Total kW d c kW ac saturator water gal/hour
Brine Water voltage current
gal/min (liters/min) (liters/hour)
46 2 .4 3 2 4 .5 6 2 6 .9 9 61
20 24 15 280 4 .2 0 4 .7 7
(21) (9.19) (92.96) (102.13) (229)
55 2 .9 1 2 9 .4 7 3 2 .3 8 68

24 28 15 336 5 .0 4 5 .7 3
(25) (11.03) (111.55) (122.56) (257)
75 3 .8 9 3 9 .2 9 4 3 .1 8 83
32 40 15 448 6 .7 2 7 .6 4
(34) (14.71) (148.74) (163.42) (313)
84 4 .3 7 4 4 .2 1 4 8 .5 8 90
36 44 15 504 7 .5 6 8 .6 0
(38) (16.55) (167.34) (183.85) (341)
93 4 .8 6 4 9 .1 7 5 4 .0 3 97
40 48 29 to 15 560 8 .4 0 9 .5 5
(42) (18.39) (185.92) (204.28) (369)
12
10 1p si
99 5 .3 4 5 4 .0 3 5 9 .3 7 0 .4 105
44 52 15 616 9 .2 4 1 0 .5 0
(45) (20.23) (204.52) (224.70) (1.5) (397)
(2.0 to
110 7.0 bar) 5 .8 3 5 8 .9 4 6 4 .7 7 112
48 56 15 672 1 0 .0 8 11.45
(50) (22.07) (223.11) (245.13) (425)
121 6 .3 2 6 3 .8 5 7 0 .1 7 119
52 60 15 728 1 0 .9 2 1 2 .4 0
(55) (23.91) (241.70) (265.61) (452)
130 6 .8 0 6 8 .7 6 7 5 .5 6 127
56 64 15 784 11.76 1 3 .3 5
(59) (25.75) (260.29) (286.04) (480)
139 7 .2 9 7 3 .6 8 8 0 .9 7 134
60 68 15 840 1 2 .6 0 1 4 .3 0
(63) (27.58) (278.90) (306.48) (508)
148 7 .7 7 7 8 .5 9 8 6 .3 6 142
64 72 15 896 1 3 .4 4 1 5 .2 5
(67) (29.42) (297.47) (326.89) (536)
C onsult the water softener manufacturer for individual peak water requirements for softener regeneration.
Dilution water requirements based on 10:1 dilution ratio.
*These output figures are theoretical maximum values and may be subject to reductions due to variations in plant operating conditions.
B1-150 OSEC© SYSTEM

- HYPOCHLORITE STORAGE TANK
85.010.170.030
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 13
B1-150 OSEC© SYSTEM - ELECTROLYZER
85.010.170.010A
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 14
B1-150 OSEC© SYSTEM - ELECTROLYZER
85.010.170.010B
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 15
IM 85.010AA UA (C/3-01) 16
SECTION 2 - INSTALLATION
List of Contents
PARA./DWG. NO.
General...................................................................... 2.1
Water Softener .......................................................... 2.2
Salt Saturator ............................................................ 2.3
Brine Pump ............................................................... 2.4
Electrolyzer ............................................................... 2.5
Transformer/Rectifier Unit ....................................... 2.6
Hypochlorite Storage Tank ....................................... 2.7
Tank Overflow ....................................................... 2.7.1
Storage Tank Outlets ............................................. 2.7.2
Hydrogen Venting System ..................................... 2.7.3
Storage Tank Levels .............................................. 2.7.4
Illustrations
B1-150 OSEC Typical Installation ........................ 85.010.110.010
Hazardous Area Zoning ......................................... 85.035.160.020
IM 85.010AA UA (C/3-01) 17
2.1 General
The electrolytic generation of sodium hypochlorite from brine results in

the production of hydrogen gas, which detrains from the hypochlorite
solution at the storage tank, therefore, great care must be taken with the
siting of the tank and the positioning of its associated electrical equip-
ment. For installation recommendations, refer to the typical layout in
Dwg. 85.010.110.010 and to any plant layout drawings specific to the
contract that may be available. The air space within the tank above the
solution naturally fills with hydrogen detraining from the solution and is
classified as a Zone 0 (Division 1) area. The other hazardous zone is a
radius of 5 feet (1.5 meters) around each tank exhaust, this area extending
for 6.5 feet (2 meters) above and 3 feet (1 meter) below the outlet. This
hazardous area is classified as a Zone 2 (Division 2) area. Refer to the
zoning diagram (Dwg. 85.035.160.020) for details. Because the tank, by
its function, creates the hazard, it must not be installed in any existing
hazardous area, or have any equipment installed in the area at a later date
that can generate a hazard.
The electrolyzer should be sited in a location with good standards of high-

and low-level ventilation, with the ambient temperature between 41° and
104°F (5° and 40°C). Whenever possible, the site chosen for the electrolyzer
should be remote from all other electrical items such as rectifiers, control
panels, and pumps, so that there is no risk of such equipment being sub-
jected to water or chemical splashing when servicing the electrolyzer.
Refer to Supplement 1 for notes on wiring regulations.
All rigid pipework carrying liquids should have solvent-welded or threaded

joints. This pipework should be installed to the pipe manufacturer’s stan-
dards. Where making threaded connections on brine or hypochlorite lines,
use a jointing compound. The gaskets, seals, and O-rings used on hy-
pochlorite pipework must be fpm (Viton). Any pipework external to the
plant rooms should be insulated and/or trace heated to prevent the possi-
bility of freezing. Each pipe must be adequately supported and secured
throughout its length, especially the hypochlorite piping from the
electrolyzer to the tank, as this solution is warm during generation periods.
All pipes and valves must be clearly labeled as to their specific duty,
contents, and flow.
2.2 Water Softener
The twin-cylinder water softener should be mounted on a flat, level base.

Where several softeners are used, it is important to follow the piping
arrangements shown in Figure 2.1. Two headers, one for the inlet and one
for the outlet, are required, with the branch connections to the softeners
IM 85.010AA UA (C/3-01) 18
being of equal diameter and length. This is to equalize any pressure drops
in the pipework so that each softener provides an equal share of the load.
Figure 2.1 - Twin-Cylinder Water Softener
To comply with local code, it is advisable to connect a combined non-

return/vacuum break valve in the incoming main to the softener. The
purpose of this valve is to prevent possible back feeding of salt into the
water main in the event of abnormal conditions—such as suction condi-
tions within the main water supply.
The main water supply inlet and the softened water outlet of the softener
should be fitted with manual isolation valves.
The cold water supply should be clean and free from turbidity, at a pres-
sure between 30 and 100 psig (2 and 7 bar), these being the pressure limits
of the electrolyzer input. This supply should have a chlorine content not
exceeding 1 mg/l or the resin bed could be adversely affected. If the
chlorine content is in excess of this value, a carbon filter must be installed
in the supply line to the softener.
In addition to the main water supply input and the outlet connections, a
further three pipes need to be run from the softener. These are the drain,
brine recharge line, and the overflow. The drain connection discharges the
brine recharge residue and backwash water from the resin bed regenera-
tion cycle. The overflow is fitted in case the internal brine piping develops
a leak. These drain and overflow connections are piped to a common
drain. The brine recharge line connects via a manual isolation valve to the
brine supply pipe from the saturator output strainer.
After installation and pipework are complete, the units will need to be
charged with salt solution for their resin bed regeneration cycles while the
salt saturator is brought on-stream. The initial filling of the saturator will
take some time, as the maximum output from a single softener is 9.5 gal/
IM 85.010AA UA (C/3-01) 19
min (36 ltr/min). The softeners will need to regenerate, on average, after
each 264 gallons (1000 liters) of softened water has been supplied from
each unit.
Until the saturator has been partially filled with softened water, however,
it cannot provide the salt solution required for softener regeneration.
Therefore, prepare some saturated brine solution in a suitable container,
such as a bucket, adding 7 lbs (3.2 kg) of salt to 2.6 gallons (10 liters) of
water and stirring until the salt has fully dissolved.
NOTE: The salt used must conform to the specification given in para-
graph 2.3.
Check that the shut-off valve in the brine supply line from the saturator to
the softener is fully closed, then reach into the softener drum and discon-
nect its brine suction line at the union just inboard from where the brine
line enters the drum. Allow the internally detached brine piping, complete
with non-return valve, to rest on the internal grid of the drum. Pour in the
prepared brine solution and check that the brine piping is fully covered.
The salt saturator can then be commissioned as detailed in the following
section. Each regeneration of a softener will use approximately 0.37 gal-
lons (1.4 liters) of brine. When the saturator has reached an operational
state, the brine suction line can be reconnected to its union and the valve
in the brine supply line from the saturator to the softener opened.
The water softener has a water meter fitted to it that initiates a regeneration
cycle after a certain quantity of softened water has been delivered. This
quantity of water differs according to the hardness of the supply water—
the harder the water, the more frequent the regeneration periods. A meter-
ing disc is fitted to the softener at the ordering stage by the manufacturers,
and therefore it is essential that the softener ordered for a particular site is
not re-routed to another without first checking upon its suitability. Simi-
larly, if the hardness of the supply water changes significantly, the water
meter disc must be changed to suit the new supply.
2.3 Salt Saturator
On installations using large salt saturators, external siting of the unit is

usually required. Refer to the manufacturer’s data sheets before installa-
tion. The saturator should rest on a firm, level foundation that is flat to
within 1/8 inch in 10 feet (3mm in 3 meters), in all directions. The base
should be swept clear of stones or other debris before placement. When
moving the tank, use only the lifting lugs fitted and move only when
empty. Do not use slings.
IM 85.010AA UA (C/3-01) 20
Remember that the tank is relatively light for its size and so the gravel bed
should be loaded fairly soon after positioning the tank, otherwise it can
easily be blown over by high winds. If necessary, it should be securely
roped down so as to avoid any possibility of this happening.
The gravel filter bed is usually a bottom bed of 1/2- to 3/4-inch (14 to
20mm) diameter, washed, round gravel and another deeper bed on top of
1/8- to 1/4-inch (3 to 6mm) diameter, washed, round gravel. Care must be
taken when adding the gravel not to damage the brine collection pipework
in the bottom of the tank. The softened water supply to the saturator should
be fitted with a Maric valve to control the water flow to 0.4 gal/min (1.5
ltr/min).
Before finally connecting the brine outlet, the gravel in the saturator must
be flushed through to ensure that all dust and dirt are removed. Continue
to flush until clear water runs from the outlet. If the flushing is carried out
by hose pipe inserted through the top cover, care should be taken to ensure
that the gravel bed layers are not disturbed. Localized washing away of
gravel could cause an area of low resistance, resulting in some particles
of salt being drawn off when the saturator is brought into operation.
NOTE: If hard water is used for flushing the gravel, ensure that the
unit is drained as far as possible before filling with soft water prior
to charging with salt.
On large proprietary saturators, particular attention should be paid to the

salt filling pipe, which is usually a large-diameter metal pipe looping over
to discharge the salt into the top of the saturator tank. This pipe has a union
connection at its lower end to which is connected a flexible delivery pipe
from the tanker during transfer of salt. It is essential that a good earth lead
is properly bonded to this metal pipe on the saturator to ensure that any
static electricity generated during deliveries of salt will be safely dis-
charged.
After washing the gravel, the saturator can be charged with salt. Turn off
the water supply and discharge 50% of the water on the small saturator or
discharge the water to approximately 19-3/4-inch (500mm) above the
gravel bed for the larger units. The saturator will now accept its full charge
and then the water supply can be turned on and allowed to fill to the normal
level.
IM 85.010AA UA (C/3-01) 21
NOTE: The salt used must conform to the following specification:
Water insolubles 0.1 % maximum

Calcium Sulfate 0.14% maximum
Magnesium Sulfate 0.02% maximum
Magnesium Chloride 0.1 % maximum
Sodium Chloride 99.82% minimum
Pure, vacuum-dried (food grade) salt or water softener salt is recom-

mended.
NOTE: With a new installation, the brine initially drawn off will not
be at the correct strength. At least 26.4 gallons (100 liters) should be
drawn from the saturator before any attempt is made to calibrate the
brine pump or brine flowmeter. The brine output should then be
checked with a hydrometer or specific brine tester to ensure the spe-
cific gravity is 1.2.
2.4 Brine Pump
The brine pump (or pumps) should be located near the salt saturator to
avoid long suction lines. The incoming supply from the saturator is fed in
1/2-inch NPT. piping to the pump liquid end. This should be fitted with
a manual isolation valve. The discharge from the pump is also piped in 1/
2-inch NPT. piping to the brine inlet at the electrolyzer. This line should
also be fitted with a manual isolation valve. The discharges from the pump
priming valve and pressure relief valve should be piped to waste.
For full details of pump installations, refer to the separate publication

supplied with the pump.
2.5 Electrolyzer
The electrolyzer should be positioned with regard to the transformer/

rectifier unit to suit the bus bar layout required. Allow sufficient clearance
around the unit for subsequent servicing, in particular at one side of the
unit to allow the electrode assemblies to be withdrawn from their casings.
The electrode assembly is approximately 3 feet (1 meter) long and can be
removed from either end of the casing. Refer to Dwg. 85.010.160.010 for
overall dimensions and pipe sizes.
The unit is skid-mounted and should be bolted down on a flat, level

surface; the hole centers for the mounting bolts are as shown in Figure 2.2.
IM 85.010AA UA (C/3-01) 22
→ 27.559” →
↓
(700mm)
25.984”
4 HOLES 0.6” (15.25mm) DIA (660mm)
FRONT
↓
Figure 2.2 - Electrolyzer Mounting Diagram
A waterproof mastic compound should be used between the base skid and
the floor to prevent any spillages of water or hypochlorite from running
under the skid and causing unnecessary corrosion. Before connecting any
discharge pipework to the outlet at the top of the integral heat exchanger,
check that the electrolyzer casing is level, adjusting the mounting brackets
as necessary. The electrolyzer may be dispatched with the electrode as-
sembly separately packed to avoid damage. For details of fitting the as-
sembly, refer to paragraph 4.4.
2.5.1 Pipe Connections to the Electrolyzer
The electrolyzer requires three pipe connections to be made, these being

shown on the information plate attached to the unit.
• The dilution water supply from the softener. This connects to a

manual water inlet valve at the bottom left of the hydraulic panel and
must be at a pressure between 30 and 100 psig (2 and 7 bar) and at a
temperature between 50° and 78.8°F (10° and 26°C)—refer to note
in paragraph 1.7. The incoming water supply is then switched by an
electric solenoid valve on the electrolyzer skid.
• The brine supply from the remote-mounted brine pump. This

connects to a union at the bottom right of the hydraulic panel, located
directly below the brine flowmeter and the back pressure valve.
NOTE: Both of these inlet connections have plain sockets for solvent-
welded pipework, the sizes of these sockets being shown on the infor-
mation plate.
• The hypochlorite product line. This connects to a socket union at

the top of the integral heat exchanger. Refer to the information plate
for sizing. The product line is fitted at the electrolyzer end with a
clear upvc sight glass to check on the product delivery.
IM 85.010AA UA (C/3-01) 23
WARNING: SHUT-OFF VALVES MUST NOT BE FITTED IN THE

! PRODUCT PIPEWORK TO THE STORAGE TANK. OVER-PRES-
SURIZATION OF THE ELECTROLYZER COULD OCCUR
SHOULD SUCH A VALVE BE ACCIDENTALLY CLOSED WITH
THE ELECTROLYZER IN OPERATION.
This hypochlorite pipework should rise vertically for at least 19-3/4-

inch (500mm) before turning horizontally, and any bends in the
pipework should be swept bends. The hypochlorite pipework from the
exchanger to the storage tank should be run in an incline of approxi-
mately 1/2 inch per 3-foot (15mm per meter) run of pipe to the top of
the tank.
These requirements are advised in order to avoid the formation of any

hydrogen gas traps in the pipework. This pipework should also be ad-
equately supported along its length as the product will be warm during
production periods. Any pipework external to the plant room should be
insulated and trace heated to prevent the possibility of freezing during low
ambient temperatures.
2.5.2 Electrical Connections
The electrical connections between the electrolyzer and the associated

remote-mounted control panel are shown on the external connection dia-
gram (Dwg. 85.035.140.010, located in Supplement 1). The connections
are made to a terminal box located on the base skid. The signals from the
high temperature sensor at the electrolyzer should be wired to the control
panel using shielded cable. The electrolyzer must be efficiently bonded to
earth. The low cell level and low flow signals are intrinsically safe circuits
and must be run separately from the other cables. Refer to Supplement 1
for general wiring installation notes.
2.6 Transformer/Rectifier Unit
The transformer/rectifier unit is positioned to suit the bus bars supplied.

The rectifier cabinet is mounted on two channel sections to raise it from
the floor, each channel being drilled with two 0.55-inch (14mm) diameter
holes for bolting the unit in position. The transformer/rectifier radiates
heat and, therefore, if the unit is located in a separate room, this room must
have adequate ventilation. As a guide, a nominal 5 to 10% of rectifier
power consumption will be given off as heat, which on larger units can be
considerable. Due consideration should be given to forced ventilation
using thermostatically controlled fans.
IM 85.010AA UA (C/3-01) 24
The DC electrolyzing voltage is brought out on two flat aluminum termi-

nals at the top of the unit. These are connected to their corresponding
polarity terminals at each end of the electrolyzer casing using the insulated
bus bars supplied. Where bus bars feed through clearance holes in any
partition wall, these holes should be sealed after fitting to prevent any
possibility of hydrogen gas entering the control room should a leakage
occur. Ensure the correct polarities are maintained between the electrolyzer
and the transformer/rectifier unit. When fitting the bus bars, ensure that
the contact faces between individual bus bars, electrolyzer end terminals,
and rectifier terminals are thoroughly clean and then coated with an elec-
trical joint compound to ensure good conductivity and to prevent corro-
sion. The bus bars connect to the connecting spacers at each end of the
electrolyzer using two hexagon-headed bolts each, tightening to a torque
of 17 ft-lb (23 Nm). At the transformer/rectifier end, the securing bolts
between the bus bars and the transformer/rectifier terminals are tightened
to a torque of 70 ft-lb (95 Nm). Ensure that flat washers are placed under
the heads of the bolts and spring washers under the nuts.
The transformer/rectifier requires a 440V, 60 Hz, three-phase, power

supply. The supply enters via a detachable panel at the lower front of the
unit and is connected to terminals on the isolator. The supplies should be
taken from a locally mounted fused isolator. The rectifier unit must be
efficiently bonded to earth.
CAUTION: The unit has a nominal input current of between 9 amps

! and 28 amps depending upon the size of the electrolyzer (refer to the
transformer/rectifier manufacturer’s data sheets). In view of the high
in-rush current to the rectifier at switch on, the use of a circuit breaker
in the main electrical supply is not recommended, conventional HRC
fuses being preferred.
In addition to the main electrical supply, the transformer/rectifier requires

further connections with the OSEC control cabinet to provide the remote
stop/start control, rectifier failure signal, improper voltage, and an
electrolyzer running contact from the main contactor. Refer to Supple-
ment 1 for details. The transformer/rectifier circuit diagram is included in
the manufacturer’s literature supplied with the equipment.
2.7 Hypochlorite Storage Tank
2.7.1 Tank Overflow
The product storage tank should be suitable for 1% sodium hypochlorite

at a temperature up to 104°F (40°C), usually being manufactured from
spirally wound, high-density, black polyethylene or premium resin FRP
IM 85.010AA UA (C/3-01) 25
with nexus veil. The tank is usually located in an area capable of contain-
ing the full tank capacity in the event of a major leakage. This area should
be fitted with an overflow switch assembly or an overflow tank to warn
of any overflow. The overflow of the tank is to be externally piped to near
the bottom of the tank so that the entry to the overflow is always sub-
merged, preventing hydrogen gas from escaping via the overflow. The
external overflow pipework to the overflow switch assembly must be
fitted with a vacuum break to prevent syphonic action from emptying the
tank should an overflow occur.
2.7.2 Storage Tank Outlets
The hypochlorite outlet and drain connections at the tank should be fitted
with manual isolation valves, the drain valve being capped to prevent
accidental draining of the tank.
2.7.3 Hydrogen Venting System
The hydrogen venting arrangement to the tank consists of either a single

or a pair of wall-mounted blower assemblies located near the tank, but not
closer than 5 feet (1.5 meters), and with their air inlets fitted with dust
filters. The blowers are not suitable for outdoor mounting. The air outlets
from the blowers combine at a blower changeover device wall-mounted
nearby. The output from device is a single 2-inch pipe to the off-center R2
flange at the top of the storage tank. This piping to the tank is fitted with
an orifice assembly in which is mounted an orifice plate, causing a small
reduction to the bore in order to create a pressure drop across it when the
blower is in operation.
From the tank side of the orifice, a tube is connected to the LP inlet of the
differential pressure switch. The switch must be mounted below the level
of the top of the tank. The HP inlet is connected to the blower side of the
orifice. The internal micro-switch of the pressure switch is connected by
a two-wire cable back to the OSEC control panel.
The normally open (N/O) contacts of the switch are utilized, the terminals
to which the switch is wired at the control panel are shown in the external
connection diagram (Dwg. 85.035.140.010, located in Supplement 1).
NOTE: The term “normal” refers to the switch with equal pressures
on both chambers—as would occur with no air flow.
The operational point of the switch is not set before dispatch, but should
be adjusted on-site to ensure that, with the blower in operation and the vent
pipework free of obstructions, the N/O contact should be closed.
IM 85.010AA UA (C/3-01) 26
To increase the differential, rotate the spring bias adjuster screw clock-
wise, or vice versa to decrease the differential. Refer to Figure 2.3 for
details.
Figure 2.3 - Hydrogen Venting System
The blower assemblies require a 110/240 V, 60 Hz, single-phase supply

that should be taken from locally mounted isolators to the starters. The
starters must be mounted below the level of the top of the tank. Refer to
Supplement 1 for details of interconnections with control panel for Start/
Stop signals.
The hydrogen exhaust from the tank is taken from the other R2 flange at
the top of the tank and is piped vertically in 2-inch (50mm) Class C rpvc
or abs piping to terminate with a cowl and bird screen. The hydrogen
discharge point must be at least 16 feet (5 meters) from any opening of the
building to prevent the possibility of ignition.
2.7.4 Storage Tank Levels
The storage tank is fitted with a hydrostatic contents level transmitter that
produces a 0 - 20 ma output signal that is proportional to the level of tank
contents. This signal is connected back to the OSEC control panel and
used to control the start/stop operation of the electrolyzer. Refer to Supple-
ment 1 for information on setting the required levels.
IM 85.010AA UA (C/3-01) 27
IM 85.010AA UA (C/3-01) 28

- TYPICAL INSTALLATION
85.010.110.010
ISSUE 1 06-00
IM 85.010AA UA (C/3-01) 29
OSEC© SYSTEM - HAZARDOUS AREA ZONING DIAGRAM
85.035.160.020
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 30
SECTION 3 - OPERATION
List of Contents
PARA. NO.
Initial Start-Up .......................................................... 3.1

Pump Calibration ...................................................... 3.2
Normal Operation ..................................................... 3.3
Tank Top-Up ............................................................ 3.4
Temporary Shut Down ............................................. 3.5
Complete Shut Down ............................................... 3.6
Failure of Main Electrical Supply ............................. 3.7
Theory of Operation ................................................. 3.8
IM 85.010AA UA (C/3-01) 31
3.1 Initial Start-Up
With the complete system, including the control panel, installed and con-
nected, and the individual items such as the water softener, salt saturator,
and brine pumps commissioned—as detailed in their respective data sheets
or manuals—the system can be brought into operation.
a. Ensure that any isolation valve on the main water supply to any strainer
in the supply to the softeners is open and the shut-off valve to the water
softener is also fully open. Any softener bypass valve should be closed.
b. Check that the isolation valve on the softened water output line from
the softener and the valve on the softened water input to the salt
saturator are both fully opened.
c. Check that the valve on the brine output from the saturator is open
and the valve on the brine recharge line to the water softener is also
open. The shut-off valves on the brine suction line to the electrolyzer
duty/standby brine pumps or single pump should be open, as should
the brine pump discharge valves. Check that the brine pump manual
stroke controls are set to approximately 75% of full stroke. These
controls may need to be adjusted for correct flowrate when the
electrolyzer starts up.
d. At the electrolyzer, check that the manual dilution water inlet valve
is fully open and the dilution water feed valve to the heat exchanger
is set in the position appropriate to the temperature of the incoming
dilution water. If the incoming water temperature is below 59°F
(15°C), the heat exchanger should be brought into use by switching
valve F so that the arrow on its handle points left toward the positive
end of the electrolyzer. Refer to paragraph 1.7 for the minimum solu-
tion temperatures permitted.
e. The acid clean/drain valve and the acid clean/sample valve should
both be fully closed.
f. Any blanking plates in the hypochlorite output line from the

electrolyzer into the storage tank should be removed. (These plates
are fitted in the line to isolate the electrolyzer when acid cleaning is
to be carried out). Check that the tank drain valve is closed.
g. Check that the current level setting control at the transformer/rectifier

unit is at minimum, then switch on the three-phase main electrical
supply to the unit at its local isolator. Switch on the transformer/recti-
fier cabinet-mounted isolator, checking that its electrical main lamp
IM 85.010AA UA (C/3-01) 32
lights, then press the OFF/RESET button, followed by the ON button

to reset its internal relays. Select AUTO on the AUTO/MAN switch.
h. Switch on the main electrical supplies to the single blower or duty/

standby blowers starters and the single brine pump or duty/standby
brine pump starters, as appropriate, at their local isolators.
i. Refer to Supplement 1 for details of control panel operation and the

alarm and status indications.
j. With the control panel set and the unit in operation, check the water
and brine flows at their respective flowmeters. The dilution water
flow is already set to the flowrate appropriate to the size of the
electrolyzer ordered. The appropriate flows are shown in the B1-150
operational data sheet (Table 1.1, located at the end of Section 1).
This flowrate is set by the sizes of the fixed orifices in the two Maric
valves of the two dilution water feed lines.
The water flowmeter is calibrated from 4.6 to 46.2 gal/hour (17.5 to

175 ltr/hour) for units up to 55 lbs/day (25 kg/day) capacity and from
11.9 to 118.9 gal/hour (45 to 450 ltr/hour) for units between 75 and
147.7 lbs/day (34 and 67 kg/day) capacity. The pressure reducing
valve should be set to a 30 psig (2 bar) output pressure on its gauge.
The brine pump stroke controls and the brine flowmeter scale are
marked in percentage values, therefore, the actual pump delivery rate
and the flowrate at these percentage values must be determined to set
the correct brine flowrate from the pump. Refer to paragraph 3.2 for
details of pump calibration. The low flow alarm switches for the two
flowmeters should be set to operate at 85% of correct flow.
The flow figures quoted in Table 1.1 are for a 10:1 dilution water/brine
ratio, producing hypochlorite with a strength of approximately 0.8%.
The electrolyzer can operate with a dilution water/brine ratio of 15:1,
producing hypochlorite of approximately 0.6% strength, with an overall
savings in cost of production. To effect this change in ratio, the orifice
inserts of the Maric valves in the two dilution water feed lines will
need to be changed. The alternative inserts for these valves are sup-
plied in a small bag tied to the unit. These inserts are marked with their
flows in ltr/min. Where the inserts for the two valves are of different
values, the insert with the larger flow figure should be fitted to the
Maric valve in the feed to the first cell. Refer to Table 3.1 for details
of Maric valve sizes for the different electrolyzer capacities.
k. With the casing full, the level switch at the hypochlorite outlet mani-
fold will have operated and signaled to the PLC to switch on the
IM 85.010AA UA (C/3-01) 33
rectifier unit. After a nominal three minutes running time to ensure

the casing is full of brine, not just water, adjust the current at the
transformer/rectifier to the current value shown on the operational
data sheet using the current level control. The rectifier voltmeter alarm
relay set points should not be set until after at least four hours of
electrolyzer operation, thus allowing the equipment to reach normal
operating temperature. The under- and over-voltage set points are
typically +1V from the normal running voltage of 14V. The set points
are easily adjusted with two screws at the front of the meter.
l. The hypochlorite is now being generated and being fed to the storage
tank. When the level in the tank passes the Low Level, the PLANT
RESET or ALARM RESET button can be pressed at the OSEC con-
troller to cancel the associated alarm lamp. This action will also re-
move the inhibit on any associated dosing pump control.
m. The hypochlorite can be sampled for analysis at the electrolyzer from

the acid clean/sample valve on the hypochlorite outlet manifold. Re-
fer to the Hydrogen Gas warning at the beginning of the manual. Do
not attempt to extract more than a small sample from this valve.
n. When the level of hypochlorite in the storage tank reaches the High
Stop level, the level switch signals to the controller to shut down the
electrolyzer and its associated equipment. The transformer/rectifier
is disabled first, removing the main DC supply from the electrolyzer
to stop the electrolysis. The brine pump continues to run and the
water valve remains open for a further preset duration, so that the
brine solution purges the remaining hypochlorite from the electrolyzer
to prevent corrosion of the electrodes. The hydrogen venting blower
continues to operate for 15 minutes after initial shut down to ensure
that any hydrogen still detraining from the newly generated hypochlo-
rite solution at the tank continues to be adequately diluted with air
before discharge. The blower then shuts down. All the status lamps
at the diagram should now be extinguished.
Where full off-peak operation is specified, the tank contents level is trans-
mitted to the OSEC controller from a hall effect pressure transducer as a
0-20mA signal. The Operator Terminal at the OSEC control panel is used
to set the tank level parameters for both off-peak and daytime hours.
The tank's High and Low level switches control the automatic operation
of the electrolyzer, stopping it from generating hypochlorite when the
High level is reached and starting it up again when the Low level is
reached. Where a full off-peak operational facility is provided, these level
IM 85.010AA UA (C/3-01) 34
switches are set so that the maximum quantity of hypochlorite is generated

during the low-cost electricity hours.
The Low Storage level switch is set to operate and warn when the hy-
pochlorite level has reached a very low point near which the hypochlorite
dosing pumps would begin to suck air or hydrogen into the system. The
PLC provides an inhibit signal to the dosing pump control to stop any
dosing pump until the hypochlorite level has risen sufficiently.
3.2 Pump Calibration
As the brine pump stroke control and the brine flowmeter are marked in
percentage values, the actual pump output and the flow through the flow-
meter at these percentages must be determined so that the brine flow can
be set to the correct flow.
To facilitate calibration, the brine supply line is fitted with a graduated

calibration column assembly, usually adjacent to the salt saturator. The tube
is always full of brine at a level slightly lower than the level in the saturator.
This is due to the difference in specific gravity of the two liquids. The
graduations on the tube are at intervals to suit the pump delivery of the
particular size of electrolyzer. The size of these graduations is marked on the
tube sliding scale. Before calibrating, check the brine output with a hydrom-
eter to ensure that the specific gravity is 1.2. To calibrate, proceed as follows:
a. With the brine pump running, note the level in the brine calibration
tube at the side of the salt saturator.
b. Quickly close the shut-off valve on the saturator side of the tube and
note the time in seconds that it takes the level to fall to the next
calibration mark. The exact quantity between the two calibrations is
marked on the scale. Immediately after timing, re-open the shut-off
valve.
To calculate the flow, use the following formula:
Flow = Quantity Pumped x 60 = 150ml/min

Time
Example: 200 ml x 60 = 250 ml/min

48 secs
Multiply this answer by 60 to determine the flow in liters/hour.
Example: 250 ml/min x 60 = 15 liters/hour

IM 85.010AA UA (C/3-01) 35
If the pump rate is incorrect, adjust the pump stroke control in the
appropriate direction and, after about 30 seconds to allow the pump to
stabilize, repeat the check. Repeat this procedure until the flowrate is
correct and note the percentage reading at the pump stroke control and
at the brine flowmeter for future reference. Once the pump has been
set, the valve into the calibration tube can be closed.
3.3 Normal Operation
Refer to Supplement 1 for details of normal operation procedures.
3.4 Tank Top-Up
With the OSEC Control in the AUTO position the Low (start) level switch
control on the electro-chlorinator operation is overridden by pressing the
TANK TOP UP button. This will start-up the hypochlorite generation
equipment regardless of the Low (start) switch being covered or not. The
equipment will shut down when the High level is reached at the storage
tank.
3.5 Temporary Shut Down
Following normal operation, the electrolyzer will enter a standby condi-

tion where the casing(s) will have been flushed with fresh brine. The
electrolyzer can subsequently be left for up to one week in this shut-down
condition.
If the electrolyzer has ceased to operate following an alarm condition that

does not initiate a refill cycle, then the electrolyzer must be drained of the
partially electrolyzed product, in order to protect the electrodes from
corrosive attack by hypochlorite.
3.6 Complete Shut Down
If the unit needs to be completely shut down for servicing purposes or due
to the need for associated equipment to be serviced, proceed as follows:
If shutting down from a normal inactive state in which electrolysis is not

taking place and the cell contains only brine solution, switch the mains
isolator at both the Transformer/Rectifier Unit and the Control Panel to
OFF. Connect a hose to the sample/drain valve on the cell outlet and open
the valve to fully drain the casing(s). Close the valve when draining is
complete.
IM 85.010AA UA (C/3-01) 36
If the need arises to shut the system down during a period of electrolysis,
turn the mode selector to INHIBIT. Electrolysis will cease. The control
panel and rectifier isolators should be turned off and the cell drained as
previously described.
3.7 Failure of Main Electrical Supply
Should the main electrical supply to the OSEC Control fail, and it is
obvious that it will not be restored within a short time (up to three hours),
the electrolyzer casing of the electrolyzer should be drained. This is to
prevent corrosion of the electrode assemblies due to reverse polarization
occurring.
The casing of the electrolyzer can be drained by first connecting a hose to

the acid clean/drain valve on the underside of the casing and directing the
hose to a suitable drain. Refer to the warning in paragraph 3.1 as to the
handling of sodium hypochlorite. Open the drain valve and allow the
casing and the hypochlorite product pipework to the storage tank to drain
down. Ideally, the casing should then be filled with clean water until such
time as the unit can be brought back into operation. This can be effected
by connecting the drain hose to a clean water supply and filling the casing.
Close the drain valve after filling.
CAUTION: If filling the casing from a main water supply, ensure

! that the casing is not subjected to a greater pressure than 30 psig (2
bar).
When the main electrical supply is restored after any outage, the OSEC
control will automatically reset, but the transformer/rectifier internal re-
lays must be manually reset by first pressing the unit OFF button, followed
by the ON button.
3.8 Theory of Operation
With the electrolyzer electrolyzer casing full of brine and dilution water
solution, the DC voltage from the associated transformer/rectifier unit can
be applied via the respective bus bars to the casing’s positive and negative
terminals. The terminals convey the supply to the individual positive and
negative electrodes within the electrolyzer casing, via internal connec-
tions. As brine is a good conductor of electricity, a current will flow
between the individual positive and negative electrodes, electrolyzing the
solution.
The electrolysis of brine results in chlorine gas (Cl2) being produced at the
positive electrodes (anodes), while sodium hydroxide (NaOH) and hydro-
IM 85.010AA UA (C/3-01) 37
gen gas (H2) are produced at the negative electrodes (cathodes). The chlo-
rine further reacts with the sodium hydroxide to form sodium hypochlorite
(NaOCl). As the solution passes through the successive cells in the casing,
the degree of conversion to sodium hypochlorite increases. The hydrogen
formed during electrolysis separates out above the electrodes, gas ports in
the cell separators producing separate gas and solution zones. At the final
cell of the casing, the gas and solution are combined at a common dis-
charge port, the emerging solution being mainly sodium hypochlorite
along with hydrogen and a small amount of unconverted brine. The output
from the electrolyzer feeds via its associated heat exchanger into a pipe-
line to the hypochlorite storage tank complex where the hydrogen is al-
lowed to gas off from the solution and be diluted with air to below 25%
of its LEL before being force-ventilated to outside atmosphere, safely
away from any sources of ignition.
When the required amount of hypochlorite has been generated, the

electrolyzer shuts down. The transformer/rectifier unit is first switched
off, stopping the electrolysis, but the water and brine continue to flow for
a short period to purge the hypochlorite from the casing as an aid to
minimizing corrosion of the electrodes. The tank blower continues to
operate for 15 minutes after shut down to ensure that the hydrogen gas
continuing to detrain from the hypochlorite is safely diluted and exhausted
to atmosphere.
IM 85.010AA UA (C/3-01) 38
IM 85.010AA UA (C/3-01)
Table 3.1 - B1-150 OSEC – Maric Valve Sizes
WATER TO 1s t CELL WATER TO 2nd CELL

NOM INAL OSEC DILUTION TOTAL WATER FLOW
M ARIC VALVE M ARIC VALVE
CAPACITY RATIO
gal/hr (l/hr) FLOW FLOW
NOM INAL PART NO. PART NO.
lbs /day (kg/day) Nominal Actual Nominal Actual gal/hr (l/hr) gal/hr (l/hr)
10:1 24.56 24 (92.96) (90) UXG.85386 0.21 (0.8) UXF.85386 0.18 (0.7)
46 (21) 15:1 36.84 36 (139.44) (138) UXL.85386 0.32 (1.2) UXK.85386 0.29 (1.1)

10:1 29.46 30 (111.5) (114) UXJ.85386 0.26 (1.0) UXH.85386 0.24 (0.9)
15:1 44.20 43 (167.32) (162) UXN.85386 0.40 (1.5) UXL.85386 0.32 (1.2)
55 (25)
10:1 39.29 40 (148.74) (150) UXM.85386 0.34 (1.3) UXL.85386 0.32 (1.2)
15:1 58.94 57 (223.11) (216) UXS.85386 0.53 (2.0) UXP.85386 0.42 (1.6)
75 (34)
10:1 44.21 44 (167.34) (168) UXN.85386 0.40 (1.5) UXM.85386 0.34 (1.3)
15:1 66.31 65 (251.01) (246) UXT.85386 0.61 (2.3) UXR.85386 0.48 (1.8)
84 (38)
39
10:1 49.12 49 (185.92) (186) UXP.85386 0.40 (1.5) UXN.85386 0.40 (1.5)
15:1 73.67 73 (278.88) (276) UXT.85386 0.61 (2.3) UXT.85386 0.61 (2.3)
93 (42)
10:1 54.03 54 (204.52) (204) UXR.85386 0.48 (1.8) UXP.85386 0.42 (1.6)
15:1 81.05 81 (306.78) (306) UXW.85386 0.74 (2.8) UXT.85386 0.61 (2.3)
99 (46)
10:1 58.94 60 (223.11) (228) UXS.85386 0.53 (2.0) UXR.85386 0.48 (1.8)
15:1 88.41 84 (334.66) (318) UXW.85386 0.74 (2.8) UXV.85386 0.66 (2.5)
110 (50)
10:1 63.85 63 (241.70) (240) UXS.85386 0.53 (2.0) UXS.85386 0.53 (2.0)
15:1 95.78 95 (362.55) (360) UXX.85386 0.85 (3.2) UXW.85386 0.74 (2.8)
12 1 (55)
10:1 68.76 68 (260.29) (258) UXT.85386 0.61 (2.3) UXS.85386 0.53 (2.0)
15:1 103.14 100 (390.43) (378) UXY.85386 0.92 (3.5) UXW.85386 0.74 (2.8)
130 (59)
10:1 73.68 73 (278.90) (276) UXT.85386 0.61 (2.3) UXT.85386 0.61 (2.3)
15:1 110.52 106 (418.35) (402) UXY.85386 0.92 (3.5) UXX.85386 0.85 (3.2)
139 (63)
10:1 78.59 79 (297.47) (300) UXV.85386 0.66 (2.5) UXV.85386 0.66 (2.5)
148 (67) 15:1 117.88 111 (446.20) (420) UXY.85386 0.92 (3.5) UXY.85386 0.92 (3.5)
IM 85.010AA UA (C/3-01) 40
SECTION 4 - SERVICE
List of Contents
PARA./DWG. NO.
Routine Maintenance ................................................ 4.1

Acid Cleaning ........................................................... 4.2
Removing the Electrode Assembly .......................... 4.3
Replacing the Electrode Assembly ........................... 4.4
Flowmeter Servicing ................................................. 4.5
Titration Procedure ................................................... 4.6
Troubleshooting ........................................................ 4.7
OSEC Operational Log ............................................. 1 Page
Illustrations
Acid Cleaning Unit ................................................ 85.035.150.010
IM 85.010AA UA (C/3-01) 41
CAUTION: It must be emphasized that, when servicing the indi-

! vidual items of equipment that form this complete system, only USF/
W&T approved parts may be used for replacement purposes.
4.1 Routine Maintenance
Recommendations for the routine maintenance of the brine pump will be

found in the specific manual supplied with the pump. This specific manual
also contains the necessary information on servicing, together with illus-
trated parts lists for spares purposes.
The periodicity of maintenance to the system cannot be accurately fore-

cast due to the varying environments encountered and the degree of usage
to which the plant is subject; however, most maintenance required is
minimal and consists mainly of good housekeeping.
It is essential that all items of equipment are kept clean of accumulations

of salt, dust, and splashes of hypochlorite in order to minimize any corro-
sion. The equipment should also be checked regularly for leaks.
4.1.1 Water Softener
The water softener is designed to operate on an on-demand basis and the

regeneration of the resin beds is automatic when sufficient water has
passed through the unit. Refer to the manual supplied with the unit for
details of any routine maintenance or servicing required. The softener is
preset to treat water with a maximum hardness of Calcium Carbonate
(CaCO3) stipulated at the time of ordering. A weekly check should be
made on both the input supply and the output of the water softener to
ensure the unit is functioning correctly. A test point is provided at the
electrolyzer to enable a test sample of softened water to be obtained. To
check the hardness of the water, a tester (such as a Hach, Model 5B Water
Hardness Tester) should be used. Refer to the hardness tester instruction
manual for the procedure to be followed.
NOTE: Where the water supply is subject to high manganese levels,

the resin bed media may need changing at long-term intervals. Refer
to the softener manufacturer for details.
4.1.2 Salt Saturator
The salt saturator is of a simple, fool-proof design requiring little attention

other than to maintain the permanent salt level to the lower limit quoted
in the manufacturer’s information. This is the maximum level at which the
unit has the capacity to accept a full recharge of salt.
IM 85.010AA UA (C/3-01) 42
The action of the incoming water suply ball valve should be periodically
checked to ensure that the water level is maintained to the manufacturer’s
figure. Check also any attached spray bar to ensure that the incoming
water is evenly distributed across the top of the tank, and not concentrated
in one particular spot, as this will create a clear path through the salt and
lead to a weak brine solution being drawn off.
Weekly checks should be made on the strength of the brine emerging from
the saturator. To enable checks to be made, a sample tap is provided on the
electrolyzer. A measuring cylinder and hydrometer specially calibrated in
percent-brine-strength are provided for testing purposes. To make a check,
half fill the measuring cylinder with brine and carefully place the hydrom-
eter in the solution. With the brine at the correct strength, the liquid level
should read 100% on the hydrometer scale.
4.1.3 Electrolyzer
Refer to the electrolyzer assembly drawing specific to the contract in-

cluded in this manual for details of individual components. The brine and
dilution flowmeters should have their metering tubes and floats periodi-
cally cleaned of any deposits to ensure their optimum performance. It is
expected that the brine flowmeter will require cleaning more frequently.
Refer to paragraph 4.5 for details.
4.1.3.1 Anode Warranty
The anodes used in the electrolyzer have a specific warranty period of five
years, unless otherwise stated at the time of ordering the equipment. The
anodes should perform satisfactorily for 60 continuous calendar months
after initial commissioning, provided that the equipment has been oper-
ated in accordance with the conditions stated on the official warranty form
and in accordance with this manual. A check on the working hours can be
obtained from the associated transformer/rectifier unit, which has a built-
in hours run meter. Claims under the warranty must be accompanied by
proof that the equipment has been operated correctly; therefore, an official
log must be kept. For this purpose, the OSEC Operational Log is included
at the end of this section. This form should be filled out on a regular basis
of not less than once per month. A signature is required against every entry
by a foreman, supervisor, or manager.
It is important that the plant is operated, maintained, and serviced in

accordance with the recommendations contained in this instruction manual.
Where, because of abnormal site conditions, an acid cleaning program is
recommended (see paragraph 4.1.3.3), this program must be adhered to,
otherwise permanent damage may be caused to the anode coatings.
IM 85.010AA UA (C/3-01) 43
4.1.3.2 Bus Bars
Regularly (at three-month intervals) check the surface temperature of the

bus bars and the various bus bar joints using a thermocouple-type ther-
mometer. The bus bar connections at each end of the electrolyzer are
equipped with central pilot holes in which to insert the thermometer probe.
These holes are accessible after removing the central knurled screws that
retain the bus bar guards and then detaching the guards. The temperatures
measured should not exceed 194°F (90°C). An excessive temperature at
a joint area points to possible erosion within the joint causing resistance
to current flow. This should be remedied by thoroughly cleaning and then
remaking the joint.
Shut down the electrolyzer as detailed in paragraph 3.6, Complete Shut

Down, and isolate the three-phase main electrical supply to the trans-
former/rectifier unit. Dismantle the faulty joint, taking note of the arrange-
ment of any spacers and washers used, and the positions and lengths of the
securing bolts or screws. Degrease the mating surfaces of the joint and
clean the surface of the bus bar with fine emery cloth until the surface is
bright and free from any corrosion. Do not use emery on the circular
connecting spacers fitted in the ends of the electrolyzer as these are silver
plated. After cleaning, thinly coat the joint surfaces with electrical joint
compound, as specified in Section 2 - Installation. Refit the bus bars,
securing with the fixings previously removed, ensuring their correct ori-
entation. Tighten the bolts to the correct torque—17 ft-lb (23 Nm) for bus
bar-to-electrolyzer joints or 70 ft-lb (95 Nm) for bus bar-to-bus bar joints.
After remaking the joints, restore the supply to the OSEC Control and the
transformer/rectifier unit. At the OSEC panel, press the PLANT RESET
or ALARM RESET button, as appropriate, to cancel any alarms. At the
transformer/rectifier, press the OFF button, followed by the ON button, to
reset its control relays.
4.1.3.3 Electrode Cleaning
The electrode assemblies must be acid cleaned at yearly intervals, or more

frequently if a reduction in the efficiency of the electrolyzer is noticed. The
water supply from the softener should have had all the hardness elements
removed, as these elements would otherwise be deposited on the elec-
trodes during electrolysis; however, the water supply may be subject to
varying levels of manganese. The water softener should be able to remove
all traces but, if not, the electrolyzer may need to be acid cleaned after any
periodic increase to remove deposits from the electrodes. Also, there may
have been breakdowns in the associated plant during the year that may
have effected the water supply and, in turn, the electrolyzer. The hy-
IM 85.010AA UA (C/3-01) 44
pochlorite should be regularly sampled to be analyzed as part of a regular

check on operational efficiency. A pointer to deposits having formed will
be a lowering of the normal working efficiency of the electrolyzer by
about 10%. The following formulae will enable the efficiency to be cal-
culated. When acid cleaning is required, either refer to USF/W&T to
arrange for such a treatment to be carried out, or, if an acid cleaning
package is available, follow the procedure in paragraph 4.2.
• Hypochlorite Strength — This is determined by conducting a titra-

tion on a sample taken from the sample valve at the hypochlorite
outlet manifold of the electrolyzer. The plant must be allowed to run
for at least 30 minutes before taking the sample, and must be running
while the sample is taken. Assuming that a 5 ml sample has been
taken:
mg/liter = (mls of titrate 20 35.46)
• Chlorine per Hour — Having determined the strength in mg/liter, the

chlorine per hour can be calculated.
(Total flow (water and brine) 1/hr x mg/l) = kg/hr

106
• Current Efficiency (derived from Faraday’s Law) — For a single elec-

trolyzer type electrolyzer, using the kg/hr figure previously calcu-
lated, the efficiency of the unit can be determined:
(kg/hr(Cl2) x 18898.233) = %
DC current
A typical figure for current efficiency is 60 to 70%, and depends on the

temperature and water/brine dilution ratio.
• Salt Usage — From the previous figures, the salt usage can be deter-
mined, this being expressed as kg of salt per kg of chlorine produced.
kg(NaCl)/kg(Cl2) = (318 x brine flow l/hr)

(1000 x kg Cl2/hr)
A typical figure is 3 to 3.5.
IM 85.010AA UA (C/3-01) 45
• Salt Conversion Efficiency — This is to establish how much of the

salt is being converted to hypochlorite in the electrolyzer.
Theoretically, it requires 1.6485 kg of salt to make 1 kg of chlorine.
Therefore salt conversion efficiency = (1.6485 x 100)

(salt usage—see above)
A typical figure is 50%.
When replacement of the electrodes is required, it is not recommended

that the electrode assemblies be dismantled on site, but be returned to
USF/W&T for refurbishing. This is because some of the assembly proce-
dures are critical and electrical shorts between plates could lead to serious
damage. Refer to paragraphs 4.3 and 4.4 for the replacement procedure.
4.1.4 Rectifier Unit
There are no routine maintenance requirements for the transformer/recti-

fier unit other than to keep its cabinet clean and ensure that all connections
are secure and tight. Before opening the unit to check on electrical items,
ensure that the supply is isolated elsewhere. Periodically check the vari-
able transformer track for wear or breakage, cleaning with a soft, damp
cloth if necessary. Also check its brushes for wear. As the unit is air-
cooled, ensure that any ventilation slots are not covered.
4.1.5 Control Cabinet
Refer to Supplement 1 for details of control panel maintenance and ser-

vicing.
4.1.6 Hypochlorite Storage Tank
There are no maintenance requirements for the storage tank other than
routine checks on the integrity of the various pipe joints and flanges.
Check also the terminations of the level switches for security and good
contact. The action of the pressure differential switch, which monitors the
air flow into the tank, is automatically checked by the OSEC PLC during
its control sequence (except U.85943 controls). The blower motor is fitted
with sealed bearings and requires no lubrication. Should the bearings
become noisy, it will be necessary either to replace the motor or fit new
bearings. If the blower suction connection draws in excessive amounts of
dust, the condition of the blower impeller should be inspected and cleaned,
if necessary. The blower discharge connection to the tank should be dis-
IM 85.010AA UA (C/3-01) 46
connected during this operation in order to avoid the possibility of the dirt
being blown into the tank on the subsequent re-starting of the blower.
Ensure the main electrical supply to the blower starter is isolated else-
where before any servicing is attempted.
4.2 Acid Cleaning
WARNING: BEFORE ACID CLEANING IT IS IMPORTANT

! THAT THE ELECTROLYZER IS FLUSHED THROUGH WITH
WATER TO REMOVE ANY TRACES OF SODIUM HYPOCHLO-
RITE AS THIS WOULD REACT WITH THE ACID TO FORM
CHLORINE.
Once initiated, the flushing sequence will operate long enough to ensure
a complete purge of the hypochlorite in the casing and, at the end of this
period, the water valve will automatically close. Switch off the main
electrical supply to the transformer/rectifier at its local isolator. Close the
manual dilution water inlet valve. Drain the electrolyzer casing and the
hypochlorite output piping by first connecting a hose to the acid clean/
drain valve and directing to a suitable drain. Open the valve and allow the
complete contents to drain.
WARNING: THE FOLLOWING PROCEDURE INVOLVES THE

! HANDLING OF BOTH CONCENTRATED AND DILUTE HY-
DROCHLORIC ACID. PERSONNEL SHOULD REFER TO THE
SAFETY WARNINGS AT THE START OF THIS MANUAL AND
TO THE ACID SUPPLIER’S INFORMATION TO BE MADE
AWARE OF THE POSSIBLE HAZARDS INVOLVED AND THE
PRECAUTIONS TO BE TAKEN.
a. Check that the acid dilutor is fitted with a 0.08-inch (2.2mm) orifice
in the acid inlet connection at the side of the dilutor. This orifice
enables the dilutor to give a nominal dilution ratio of 10:1 (water:acid).
Taking note of the acid warnings, connect the hose from a carboy of
36% strength concentrated hydrochloric acid to the acid inlet collet.
Ensure that the hose connection is secure both at the dilutor and at
the acid carboy.
b. Connect a fresh water supply of minimum pressure 1.5 bar to the

hose spigot at the end of the dilutor and check that the connection is
secure.
c. Unlock the float level indicator at the dilute acid tank by turning the
central knob until the float is free to rise.
IM 85.010AA UA (C/3-01) 47
d. Turn on the water supply to the dilutor and allow the dilute acid to
fill the 26.4-gallon (100-liter) tank approximately 40% full, then turn
off the water supply. Disconnect the water supply hose and also the
acid carboy hose, taking heed of the acid warnings.
NOTE: With a concentrated acid strength of 36% and a 10:1 dilution

ratio, the strength of the dilute acid produced will be a nominal 4%,
and 0.95 gallons (3.6 liters) of concentrated acid will be used to create
10.6 gallons (40 liters) of dilute solution.
e. Connect a hose from the outlet of the tank-mounted barrel pump to

the hose spigot at the acid clean/drain valve on the underside of the
electrolyzer casing. Also connect a hose from the acid clean/sample
valve at the hypochlorite outlet manifold back to the return tank con-
nection on the top of the dilute acid tank. Check that all hose connec-
tions are clamped and secure.
NOTE: The acid clean/sample valve is already fitted with a length of

clear PVC hose that runs down the side of the column to the base. This
hose can either be temporarily disconnected from the valve to enable
the acid return hose to be connected directly, or the acid return hose
may be connected to the end of the existing hose.
f. Turn the valve on the dilution water feed line to the heat exchanger
so that the heat exchanger is by-passed, preventing any acid flow
through the exchanger. The arrow of the valve handle should point to
the right, toward the hypochlorite outlet end of the exchanger.
g. Fully open both acid clean valves.
h. Connect the pump to the electricity supply and switch it on at the

pump-mounted switch.
i. Allow the dilute acid solution to circulate through the casing for 30
minutes or longer, depending on the amount of scaling. The presence
of carbon dioxide gas bubbles in the acid return line indicates that
descaling is in process.
j. Switch off the pump and allow the acid solution to flow back into the
tank as much as possible.
k. Open the manual dilution water inlet valve. Select the AUTO mode
at the OSEC control and then, almost immediately, select the FLUSH
mode again, or press MAN FLUSH, as appropriate to the type of
control panel, to initiate a new flush sequence. Allow the water to fill
IM 85.010AA UA (C/3-01) 48
the casing and then flow into the acid tank. The flush duration is
preset to allow approximately two complete changes of electrolyzer
contents.
l. At the end of the flushing sequence, leave the selector in the FLUSH
mode and allow the water in the electrolyzer to drain back into the
dilute acid tank. Disconnect the tubing of the acid return line from
the acid clean/sample valve to allow air into the electrolyzer casing
to assist draining.
m. Fully close both acid clean valves and remove the plastic tubing.
n. If the electrode assembly is to be examined visually or serviced, pro-

ceed directly to paragraph 4.3.
o. If the electrolyzer is to be brought back into operation, remove the

blanking disc previously inserted in the union at the hypochlorite
outlet on the top of the heat exchanger. Ensure the union nut is fully
tightened when refitted. Re-select the heat exchanger at valve F, its
handle pointing toward the left-hand end (+ve) of the electrolyzer.
p. Switch on the transformer/rectifier unit at its local isolator and press

the OFF/RESET button, followed by the ON button. Turn the current
control to minimum.
q. Select AUTO mode, followed by FLUSH mode, or MAN FLUSH,

as appropriate to the control panel supplied, to initiate the filling of
the electrolyzer casing with water. At the completion of the flush
cycle, reselect AUTO, allowing the electrolyzer to start up again. After
a nominal three minutes running time to ensure the casing now con-
tains brine rather than plain water, increase the current control at the
transformer/rectifier to the normal running current, as shown on Table
1.1, located at the end of Section 1.
r. Neutralize the spent dilute acid in the tank by slowly adding soda ash
or sodium bicarbonate to the solution until it ceases to effervesce.
Ensure the room is well ventilated to dissipate the carbon dioxide
gas produced. Check that the solution is neutralized by testing with
pH indicator paper. The paper should register a value of pH7 or above
(a yellow indication, not red). The solution should then be disposed
of in a safe manner. To empty the tank, redirect the outlet hose from
the acid pump to the drain or a suitably sized container ready to re-
ceive the solution and then switch on the pump again. When empty,
flush the tank and pump with clean water to purge them of any resi-
due. Switch off the pump and isolate its supply.
IM 85.010AA UA (C/3-01) 49
4.3 Removing the Electrode Assembly
WARNING: DO NOT USE METAL TOOLS IN CLOSE PROXIM-

! ITY TO THE ELECTROLYZER CASING OR THE BUS BARS
WHILE POWER IS BEING APPLIED TO THE CASING. AL-
THOUGH THE VOLTAGE IS LOW (NOMINAL 15V), THE CUR-
RENT BEING APPLIED IS HIGH (BETWEEN 280A AND 900A,
DEPENDING ON THE CAPACITY OF THE ELECTROLYZER—
REFER TO TRANSFORMER MANUFACTURER’S DATA
SHEET) AND SERIOUS INJURY COULD RESULT FROM SHOR-
ING OUT THE BUS BARS. ENSURE THAT THE SYSTEM IS
FULLY SHUT DOWN AND THE TRANSFORMER/RECTIFIER
IS ISOLATED BEFORE SERVICING STARTS.
a. If performing this service without any prior acid cleaning, shut down
the electrolyzer (as detailed in paragraph 3.6, Complete Shut Down)
and then close the main dilution water inlet valve (as shown on Dwg.
85.010.160.010).
b. Drain the electrolyzer casing and the hypochlorite output piping by

connecting a hose to the nipple of the acid clean/drain valve and
directing the hose to a suitable drain. Open the valve and ensure the
casing and pipework fully drain.
c. Detach the bus bar guards from each end of the electrolyzer by re-
moving their center screws and lifting the guards clear.
d. Remove the two bolts securing each bus bar to the connecting spac-
ers at the end flanges of the casing and separate the connection en-
suring that either the lengths of the bus bars are adequately supported
throughout their length so as not to strain or distort their connections
at the transformer/rectifier unit or that they are completely removed
from the transformer/rectifier.
NOTE: The electrolyzer is designed so that the electrode assembly

can be removed from either end of the electrolyzer casing, but this will
depend on the orientation of the unit within the plant room and suf-
ficient clearance available at the ends of the electrolyzer. In the fol-
lowing steps, it is assumed that adequate clearance is available at the
right-hand end of the unit to remove the electrode assembly (approxi-
mately 3-1/2 feet (1.1 meters)). If, because of space limitations, the
electrode assembly needs to be removed from the left-hand end, the
handing and polarity referred to in the text should be read as the
opposite hand.
IM 85.010AA UA (C/3-01) 50
e. Remove the two screws recessed in the connecting spacer fitted in

the center of the positive (left-hand) end flange and remove the spacer.
Then remove the eight bolts and nuts that secure the negative (right-
hand) end flange to the casing.
f. Insert two wide-bladed screwdrivers or flat-ended levers in the gap

between the two flanges where the eight bolts have been removed
and ease the electrode assembly out of the casing by about 3/4-inch
(20mm).
g. Remove the complete assembly by grasping the separated end flange

and the tie rod spacers as the electrode assembly emerges. If the elec-
trode assembly seems tight in the casing, check that the casing mount-
ing straps are not too tight, distorting the casing. The straps’ screws
should be just over finger-tight.
WARNING: ELECTRODE PLATE EDGES MAY BE SHARP.

! AVOID HANDLING BY THE ELECTRODE STACKS AS INJURY
MAY RESULT.
h. The negative end flange can be removed from the detached electrode
assembly by removing the screws recessed in the connecting spacer
in the center of the flange and lifting the flange and spacer from the
assembly.
i. The left-hand end flange still attached to the electrolyzer casing can
now be removed if desired, though it is not strictly necessary.
CAUTION: It is not recommended for unauthorized personnel to

! attempt to dismantle the electrode assemblies to replace individual
electrodes, as some of the assembly procedures are critical and elec-
trical shorts between plates could lead to serious damage.
4.4 Replacing the Electrode Assembly
The electrode assembly end blocks are marked with their respective po-
larities, as well as an arrowhead indicating which way up the electrode
assembly is placed within the casing. The negative end of the electrode
assembly also has an extended upper tie rod (Dwg. 85.035.160.010) that
locates in a hole on the inner face of a negative end flange.
a. Fit the left-hand end flange to the casing, if previously removed, first
smearing its gasket with a little silicone grease and checking on the
assembly drawing that it has the correct polarity engraved on it, and
IM 85.010AA UA (C/3-01) 51
that it is being fitted in the correct orientation. Secure with the eight
bolts and nuts, tightening to a torque of 25 ft-lb (34 Nm).
b. Ensure that the two O-rings fitted to the end blocks at each end of the
electrode assembly are correctly located and undamaged. Lightly
smear each O-ring with silicone grease.
c. Observing the correct polarity and orientation, insert the electrode

assembly into the casing so that the positive end block locates in the
central hole of the refitted left-hand end flange.
d. Using the palm of the hand, firmly push the electrode assembly—
complete with its end flange and gasket if not previously removed—
into the casing in order to seat the two O-rings of the end block into
the bore of the left-hand refitted end flange.
e. Refit the right-hand end flange and gasket to the casing, smearing
the gasket with a little silicone grease. Check that the flange is cor-
rectly orientated and that its central hole locates on the electrode end
block. If the flange had been removed from the electrode assembly,
also check that the extended tie rod at the right-hand end of the as-
sembly locates in its hole in the end flange. Secure with the eight
bolts and nuts, tightening to a torque of 25 ft-lb (34 Nm).
f. Refit the circular connecting spacers in the recesses at the end flanges,
having first coated their joint faces with electrical jointing compound,
and secure each with its two screws in the recessed holes, tightening
to a torque of 17 ft-lb (23 Nm).
NOTE: All metal-to-metal joint faces at the electrolyzer between the

various end spacers and all bus bars should have a thin coating of
electrical jointing compound, as described in Section 2.
g. Refit the bus bars to the connecting spacers at each end of the elec-
trolyzer and secure each with their two bolts, tightening to a torque
of 17 ft-lb (23 Nm). If the bus bars had been removed from the trans-
former/rectifier unit terminals, refit the mounting bolts, washers, and
nuts, tightening to a torque of 70 ft-lb (95 Nm). Refit the sealing
plates at the wall access holes if previously removed.
h. Cover the bus bar connection at each end of the electrolyzer with the
bus bar guards, securing them with their center screws.
i. Bring the electrolyzer back into service by first closing the previ-
ously opened drain valves and opening the dilution water inlet valve.
IM 85.010AA UA (C/3-01) 52
Remove the blanking disc previously inserted in the union at the hy-
pochlorite outlet at the top of the heat exchanger. Ensure the union
nut is fully tightened. Check that the heat exchanger is selected at
valve F if appropriate. Start up as described in paragraph 3.1.
4.5 Flowmeter Servicing
The two flowmeters on the electrolyzer can be stripped down on site for
cleaning, without the need to disturb the piping. Temporarily shut down
the electrolyzer (as detailed in paragraph 3.5, Temporary Shut Down), if
not already shut down for previous service procedures, then close the
dilution water inlet valve.
NOTE: The flowmeters cannot be drained due to the non-return

action of their floats and also the back pressure valve in the line to the
brine flowmeter. Have an absorbent cloth on hand to catch any liquid
released when removing the flowmeters.
a. Unscrew the large union nuts at each end of the flowmeter and
carefully lift the tube clear, taking care not to strain the still-at-
tached cable of its minimum flow switch.
b. Mark the relative position of the flow switch on the back of the
flowmeter tube and then slacken its clamping screw to enable the
switch assembly to be slid from the tube. Do not disconnect the
cable from the switch.
c. Clean all the parts in warm, soapy water and inspect for damage
or wear. Do not use solvents or abrasive cleaners on any of the
parts. Check the O-rings in the recesses at each end of the tube
and replace, if necessary, with new Viton or ptfe O-rings.
d. Replacement is the reverse order, making sure the float is in-

serted with its point facing downward and that the O-rings are
lightly lubricated with silicone grease.
e. After tightening the union nuts at either end of the flowmeter,

reset the minimum flow switch to the previously marked setting
and then tighten its clamp screw. These settings are usually 85%
of normal flow.
f. After servicing is complete, check that the flowmeter union nuts

are tight. Open the dilution water inlet valve. Switch on the OSEC
controller and press the PLANT RESET or ALARM RESET but-
ton, if necessary, to clear the alarms. Re-select AUTO mode—if
IM 85.010AA UA (C/3-01) 53
previously selected—to start up the system again, level switches

permitting.
4.6 Titration Procedure
To enable the product strength of the generated hypochlorite to be calcu-

lated, a sample must be taken from the sample valve at the outlet manifold.
Refer to the Sodium Hypochlorite and Hydrogen Gas warnings at the front
of this manual.
NOTE: The chemical reagents required for the following titration

include potassium iodide, sodium thiosulphate solution (0.1N), and
acetic acid (50%) or citric acid crystals.
a. Place approximately 50 ml of distilled water in a flask.
b. Add 1 gram of potassium iodide.
c. Add 20 ml of 50% acetic acid, or approximately 10 grams of citric

acid crystals to the flask.
d. Using a pipette, take 5 ml of OSEC product sample and place it in

the flask.
e. Titrate with the sodium thiosulphate solution, slowly adding the so-
lution in small, measured doses until all the color has cleared. Note
the quantity of solution used in ml. For a more accurate end-point
determination, add starch or a similar indicator to the cleared solu-
tion and then add more thiosulphate until the solution clears again,
noting the amount of thiosulphate used.
f. Calculate the product strength as follows:
T x 3.546 x 1000 = mg/l chlorine

V
Where T = Titration result in ml

and V = Volume of sample in ml
4.7 Troubleshooting
Refer to Supplement 1 for details of the various fault alarms that may
register at the control panel, together with their possible causes and rem-
edies.
IM 85.010AA UA (C/3-01) 54
OSEC Operational Log
OSEC MODEL NO.:.......................................... SIT E:................................... DAT E COMMISSIONED:.......................................
CAPACIT Y:.............................. kg(lb)/day
SET T ING FOR NORMAL RUNNING:.......................................... WATER FLOW RATE:......................................................gal(l)/hr
BRINE FLOW RATE:.......................................................gal(l)/hr
HEAT EXCHANGER FITTED? Y ES/NO AMPERES:.................................................................................
VOLTS:......................................................................................
RECOMMENDED ACID CLEANING FREQUENCY:............................................................................................................................
NOT E: T HE TABLE BELOW MUST BE COMPLET ED AT LEAST EVERY MONT H
WATER FLOW BRINE FLOW INLET WATER

DATE AMPS VOLTS SIGNATURE POSITION
gal(l)/hour gal(l)/hr TEMP°F (°C)
IM 85.010AA UA (C/3-01) 55
OSEC© SYSTEM - ACID CLEANING UNIT
85.035.150.010
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 56
SECTION 5 - ILLUSTRATIONS
List of Contents
DRAWING NO.
Ancillary Components ......................................... 85.010.000.010A&B

B1-150 OSEC General Assembly ....................... 85.010.160.010A-D
Typical Electrode Assembly ................................ 85.035.160.010
IM 85.010AA UA (C/3-01) 57
B1-150 OSEC© SYSTEM - ANCILLARY COMPONENTS
85.010.000.010A
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 58
B1-150 OSEC© SYSTEM - ANCILLARY COMPONENTS
85.010.000.010B
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 59
REFER TO DWG. 85.010.160.010D FOR NOTES.
B1-150 OSEC© SYSTEM - GENERAL ASSEMBLY
85.010.160.010A
ISSUE 1 1-00
IM 85.010AA UA (C/3-01) 60
85.010.160.010B
ISSUE 1 1-00
IM 85.010AA UA (C/3-01) 61

85.010.160.010C
ISSUE 0 1-00
IM 85.010AA UA (C/3-01) 62
NOTES:
! WATER INLET SOLENOID VALVE (U80264) SUPPLIED AS A LOOSE ITEM TO BE MOUNTED IN LINE AT LEAST 15
METERS AWAY FROM OSEC GENERATOR SKID UNIT.
✴ PLACE MARIC VALVE FOR 15:1 DILUTION RATION INTO SUITABLE CONTAINER AND MARK "FOR USE WITH
15:1 DILUTION RATIO."
# CALLED FOR ON SALES ORDER.
$ DRILL HANDLE ON BALL VALVE AND FIT SPLIT RING AND IDENTIFICATION TAG.
% APPLY A THIN COAT OF E416 SILICONE GREASE TO 0-RINGS BEFORE ASSEMBLY.
APPLY SUFFICIENT E80178 ELECTRICAL JOINTING COMPOUND TO COVER ALL METALLIC MATING SURFACES.
TIGHTEN HEXAGON HEAD BOLTS TO 23 Nm TORQUE.
ALL SOLVENT-WELDED JOINTS TO BE ASSEMBLED USING TANGIT CEMENT.
MAXIMUM WORKING PRESSURE IS 6 BAR. ENSURE W.P.R.V. IS SET AT 2 BAR.
PLACE THE FOLLOWING ITEMS IN A BAG AND TIE TO UNIT (FOR USE WITH G.20 BRINE PUMP):
P86563 - COLLET P89036 - COLLET P89037 - SPIGOT
JP83536 - UNION BODY P100738 - UNION NUT RP50-4450 - P.T.F.E. TUBE (12 Lg)
L80186 - INSTRUCTION SHEET
85.010.160.010D
ISSUE 0 1-00
IM 85.010AA UA (C/3-01) 63
OSEC© SYSTEM - TYPICAL ELECTRODE ASSEMBLY
85.035.160.010
ISSUE 0 10-97
IM 85.010AA UA (C/3-01) 64
SECTION 6 - SPARE PARTS LIST
QTY. DESCRIPTION PART NO.
1 Electrical Jointing Compound U 85553

2 O-ring PXA 30343
1 Gasket P 32164
1 O-ring P 38437
2 O-ring PXV 38437
1 Diaphragm P 41096
2 Gasket P 53981
4 O-ring P 55253
1 O-ring PXC 82206
2 Gasket P 88081
1 Gasket P 88615
6 O-ring P 88641
7 O-ring P 88744
2 O-ring P 88873
8 O-ring P 89300
1 Gasket JPXQ 81423
120 1/4" O.D. Nylon Tube RP61-4440
IM 85.010AA UA (C/3-01) 65
OSEC® CONTROL PANEL
INTRODUCTION
The OSEC® system described in the main part of this manual is under the
control of an integral panel that is mounted above the transformer/rectifier
unit. This supplement fully describes this control panel, including its
connection details, operation, and troubleshooting, should an alarm con-
dition occur.
Table Of Contents
Technical Data .......................................................... Section 1

Installation ................................................................ Section 2
Operation .................................................................. Section 3
Service ...................................................................... Section 4
Illustrations ............................................................... Section 5
SUPPLEMENT 1
ISSUE B
PAGE 1 OF 42
®
OSEC CONTROL PANEL
Supplement 1 (B/7-00) CP-2

®
OSEC CONTROL PANEL
SECTION 1 - TECHNICAL DATA
List of Contents
PARA. NO.
General Description .................................................. 1.1

OSEC System Control Sequence .............................. 1.2
Status and Alarm Indications .................................... 1.3
Alarm Relays ............................................................ 1.4
Programmable Input Alarms..................................... 1.5
Operator Terminal .................................................... 1.6
Tank Level ................................................................ 1.7
Event Log.................................................................. 1.8
Room Ventilation ..................................................... 1.9
Tandem Link (Two OSECs) ..................................... 1.10
Dosing Pump Enable ................................................ 1.11
Electrolyzer Running Relay ...................................... 1.12
Monitor ..................................................................... 1.13
Information ............................................................... 1.14
Help .......................................................................... 1.15
Hydrogen Detection (Optional) ................................ 1.16
1.1 General Description
The OSEC Control Panel monitors and supervises the On Site Electro
Chlorination process described in the main electrolyzer manual. Housed
in a wall-mounted, sheet metal cabinet, the OSEC Control Panel utilizes
a FX-32MR PLC (programmable logic controller) to manage the system.
An operator terminal fitted to the front door of the control panel allows
access to system data and control parameters via a keypad interface. Using
the level transmission signal from the hypochlorite storage tank(s), the
Controller ensures the hypochlorite product is always available for dosing
purposes.
Associated with the FX-32MR processor unit—which also incorporates

the memory module—are two expansion units for input and output signal
interfacing. The input interface provides the connections between the
various plant process monitors, switches, sensors, and relays, and con-
verts these inputs into logic signals for the processor unit. The output
interface converts the digital output signals from the processor into a form
capable of driving the various contactors, solenoids, motorized valves,
etc.

®
OSEC CONTROL PANEL
As the input signals are received, the processor examines their logic status
and compares this information with the user program stored in its memory.
It then determines whether any control action is required and, if necessary,
provides the requisite signals to the output interface. It then re-examines
the status levels of the input signals again and repeats the control process.
1.2 OSEC System Control Sequence
Under normal operating conditions, the OSEC system is set to OSEC

AUTO and the control sequence begins with a low-level signal from the
storage tank. This signals the PLC to switch on the brine pump and open
the dilution water inlet valve. After a short delay, the transformer/rectifier
output is switched on and the storage tank venting blower is started.
The hypochlorite is now being generated and fed to the storage tank where
the hydrogen is detrained and vented by the blower.
When the level in the tank reaches the high level setting, the transformer/
rectifier is switched off, stopping any further electrolysis. The brine pump
continues to run and the water valve remains open for a preset period to
purge the remaining hypochlorite from the electrolyzer casing to mini-
mize corrosion of the electrodes.
The length of time that the brine and water remain flowing is programmed
into the PLC to match the normal brine and water flows for the particular
capacity electrolyzer so that the electrolyzer has a complete change of
fluid. The hydrogen venting blower continues to operate for 15 minutes
after shut down so that any hydrogen still detraining from the newly gen-
erated hypochlorite in the tank continues to be diluted and vented.
1.3 Status and Alarm Indications
When an alarm condition is detected, the word ALARM appears in the top
right-hand corner of the Operator Terminal display and the audible alarm
is turned on. When appropriate, the system is shut down.
The alarm condition is written to the ALARM LIST with a date and time
record. When the ALARM LIST key is pressed, the list is displayed and
the audible is silenced. At the display the alarm status is ascertained by
reference to the symbol preceding the alarm name, these are:
* - Not accepted or reset

- - Accepted but not reset
$ - Reset but not accepted
- Accepted and reset
®
OSEC CONTROL PANEL
Exit the ALARM LIST by using either the ALARM LIST or MAIN MENU
keys. The ALARM LIST is cleared when power is removed from the
operator terminal or the operator terminal program is restarted.
Alarms can only be reset (by pressing the ALARM ACK key after clearing
the alarm condition) while the ALARM LIST is displayed.
• BRINE PUMP FAULT: Derived from the brine flow switch contact
that opens under the no-flow condition, this alarms is inhibited when
the brine pump is not running and for a configurable time of up to
300 seconds after brine pump start-up. There is also a two-second
transient time to accommodate fluctuations in the brine flow.
• BRINE PUMP FAILED: This alarm is generated if the brine flow

switch contact opens when the system is configured for single pump
operation. The priority alarm relay is de-energized. The electrolyzer
is shut down, but the hydrogen blower remains on for 15 minutes.
• DUTY BRINE FAILED: An alarm generated if the brine flow switch

contact opens when the system is configured for two-pump opera-
tion and the duty pump is running. The minor alarm relay is de-ener-
gized and the standby brine pump is started.
• STANDBY BRINE FAIL: This alarm is generated if the brine flow

switch contact opens while the standby pump is running. The prior-
ity alarm relay is de-energized. The electrolyzer is shut down, but the
hydrogen blower remains on for 15 minutes.
• LOW WATER FLOW: Derived from the contact of the water flow
switch that opens under the no-flow condition. The alarm is inhib-
ited when the water solenoid valve is closed and for 30 seconds after
the valve is opened. There is also a two-second transient time to ac-
commodate fluctuations in the water flow.
When this alarm is generated, the priority alarm relay is de-energized,

the electrolyzer is shut down, and the hydrogen blower remains on for
15 minutes.
• LOW ELECT TEMP: Derived from a temperature sensor mounted

in the inlet pipework of the electrolyzer and connected to a signal
convertor within the control panel. The 4 to 20 mA output from the
signal convertor is applied to an analog input on the PLC. A trip level
equivalent to 50°F (10°C) is set in the software. This alarm is inhib-
ited when the electrolyzer is off and for 20 minutes after the

®
OSEC CONTROL PANEL
electrolyzer is started. There is a 10-second transient time before the

alarm is generated.
If this alarm is generated, the priority alarm relay is de-energized, the

electrolyzer is shut down, and the hydrogen blower continues to run
for 15 minutes.
• HIGH ELECT TEMP: Derived from a temperature sensor that is

mounted in the electrolyzer outlet pipework and connected to a sig-
nal convertor within the control panel. The 4 to 20 mA output from
the signal convertor is applied to an analog input on the PLC. A trip
level equivalent to 113°F (45°C) is set in the software. There is a 10-
second transient time before the alarm is generated.

electrolyzer is shut down, and the hydrogen blower continues to run
for 15 minutes.
• LOW ELECT LEVEL: Generated by a level switch located on the

electrolyzer cell. Alarm initiation is dependant on the control mode
of the electrolyzer when the condition occurs.
† In the FLUSH mode, the alarm is inhibited.
† In the INHIBIT mode, the electrolyte level is continuously moni-

tored. If the level switch contact opens, this alarm is generated
and the minor alarm relay is de-energized.
† In the AUTO mode, the control action is further dependant on

whether the electrolyzer is RUNNING or WAITING for the next
fill request, e.g.:
‡ ELECTROLYZER RUNNING: There is a four-second tran-

sient time before any action is taken, after which the Low
Elect Level alarm is generated and the priority alarm relay is
de-energized. The electrolyzer is shut down and the hydro-
gen blower continues to run for 15 minutes.
‡ ELECTROLYZER WAITING: An automatic top-up is started,

meaning the brine pump is started and, once flow is estab-
lished, the water valve is opened. These flows continue until
the alarm condition clears and then remain on for a further 20
seconds. The maximum run time for any top-up cycle is lim-
ited to two minutes and the top-up may only be performed
once in any ‘waiting’ period. If the top-up cycle is exceeded
®
OSEC CONTROL PANEL
or a second low level condition occurs, the Low Elect Level

alarm is generated and the minor alarm relay is de-energized.
When the system is selected for AUTO but has not yet run, the
Low Elect Level alarm is inhibited. In this case, when the
electrolyzer is required to start, the normal control sequence is
entered but the rectifier is not started until the cell level switch
closes. The system has the start-up inhibit time to achieve this
before automatic shut down occurs. This method enables an empty
electrolyzer to fill with brine and water and to start without gen-
erating alarms.
• RECTIFIER FAILED: The rectifier alarm is derived from a con-

tact (closed when healthy) that is located in the transformer/rectifier.
This alarm is inhibited when the rectifier is switched off and for 120
seconds after it is switched on.
If this alarm is generated, the priority alarm relay is de-energized. The

electrolyzer is shut down and primed 0 and the hydrogen blower is run
for a further 15 minutes.
• IMPROPER VOLTAGE: Derived from a contact (closed when

healthy) situated in the transformer/rectifier. Inhibited when the rec-
tifier is switched off, the alarm is also inhibited for 120 seconds after
the unit is switched on.

electrolyzer is shut down and primed, and the hydrogen blower is run
for a further 15 minutes.
• HYDROGEN BLOWER FAILED: Derived from an air flow switch

mounted in the blower ductwork. The switch contact (open in the no-
flow state) is used to initiate a changeover to the standby blower if
the duty unit fails. The switch itself is monitored for correct opera-
tion.
The alarm is inhibited when the blower is off and for 60 seconds after
the blower is started. A five-second transient time is allowed for varia-
tions in the air flow.
• BLOWER FAILED: If this alarm is generated when the system is

configured for a single hydrogen blower, the priority alarm relay is
de-energized and the electrolyzer is shut down and primed.

®
OSEC CONTROL PANEL
• DUTY BLOWER FAILED: If this alarm is generated when the sys-

tem is configured for two blowers and the duty unit is running, the
minor alarm relay is de-energized and the standby blower started.
• STANDBY BLOW FAILED: If this alarm is generated when the

standby blower is running, the priority alarm relay is de-energized
and the electrolyzer is shut down and primed.
• AIR SWITCH FAIL: When a blower is stopped, the air flow switch
is checked to see that it returns to the open, no-flow condition. If the
switch does not return within 120 seconds, this alarm is generated
and the minor alarm relay is de-energized.
• PRODUCT TANK OVER: Derived from an overflow container in

the storage tank bund, this alarm is triggered by the container’s float
switch contact, which is normally closed.
If this alarm is generated, the priority alarm relay is de-energized and,

if the electrolyzer is running, the unit is shut down, but the hydrogen
blower continues running for a further 15 minutes.
• PRODUCT TANK LOW: This alarm is generated if the product in

the storage tank falls below the low storage trip level set in the stor-
age levels menu. If initiated, the minor alarm relay is de-energized.
• TANK SIGNAL LOST: If the input signal from the product tank
level monitoring system should fall below 2 mA, this alarm is gener-
ated and the priority alarm relay is de-energized. If the electrolyzer is
running, it is shut down and primed and the hydrogen blower contin-
ues to run for 15 minutes. While this alarm is present, the electrolyzer
is prevented from running.
• IN TEMP SIG LOST/OUT TEMP SIG LOST: If the signal from

either temperature monitoring system should fall below 2 mA, the
respective alarm is generated and the priority alarm relay de-ener-
gized. If the electrolyzer is running, it is shut down and primed. The
hydrogen blower remains running for 15 minutes. While either of
these alarms remains active, the electrolyzer is prevented from start-
ing.
• PLC ———: If the software detects a PLC fault, an alarm is gener-

ated in the alarm list with the text prefixed ‘PLC’ and followed by
the fault type.

®
OSEC CONTROL PANEL
• HYDROGEN LEAK: If the leak detector contact opens, this alarm

is generated and the priority alarm relay is de-energized. If the
electrolyzer is running, all run signals are removed (shut-down hav-
ing been achieved through the hard-wired circuits).
This alarm is derived from a separate hydrogen detector (if used), the
contact from which should be closed when healthy and open on alarm.
Located in a hard-wired circuit, the contact is used to stop the rectifier,
close the water supply valve, stop the brine pump, and stop the hydro-
gen blower. It is also taken as an input to the PLC.
• ROOM VENT FAULT: If this alarm is generated, the priority alarm

relay is de-energized and, if running, the electrolyzer is shut down
and primed. The hydrogen blower continues to run for 15 minutes.
The way the room ventilation alarm condition is monitored depends

on how the room ventilation system is configured (see paragraph 1.9).
• EMERGENCY STOP: If this alarm is generated, the priority alarm

relay is de-energized; if the electrolyzer is running, all the run signals
are removed (shut-down having been achieved through the hard-wired
circuits).
The emergency stop push button forms part of the hard-wired shut-
down circuit; the contacts should be closed when healthy. This push
button is also monitored by the software.
1.4 Alarm Relays
Three relays, each with a single, volt-free contact are provided for alarm
monitoring. These operate in a fail safe mode, i.e., the relays are energized
when the system is healthy.
• HYDROGEN LEAK - This alarm is derived from the hydrogen leak

detector alarm input
• MINOR ALARM - This relay is controlled by those alarms that do

not initiate electrolyzer shut down procedure
• PRIORITY ALARM - This relay is controlled by those alarms that

do initiate the electrolyzer shut down procedure

®
OSEC CONTROL PANEL
1.5 Programmable Input Alarms
There are three programmable input alarms. Each is set when the system
is configured. Selection of the alarms is made from the following list:
Off Water softener failed

Relief valve passing Aux. alarm (1, 2, or 3)
Salt saturator overflow Remote Inhibit - (programmable input 1
only)
• RELIEF VALVE: If the volt-free contact associated with the relief

valve is connected to the input, when the contact opens, this alarm is
generated and the priority alarm relay de-energized. The electrolyzer
is shut down, but the hydrogen blower is left running for a further 15
minutes.
• SATURATOR OVERFLOW: If the volt-free contact associated with

the salt saturator overflow switch is connected to the input, should
the contact open this alarm is generated. The minor alarm relay is de-
energized; the electrolyzer (if on) remains running.
• SOFTENER FAILED: If the volt free contact associated with the

water softener failure is connected to the input, this alarm is gener-
ated should the contact open. The minor alarm relay is de-energized
and, if the electrolyzer is running, it continues to run.
• AUX ALARM (1, 2 or 3): If this alarm is selected during configura-

tion, the action taken when the associated contact opens is dependant
on other parameters that also need to be set during configuration,
i.e., inhibit time and control action. The alarm is generated if the
contact opens and either the minor or the priority alarm relay is de-
energized. The electrolyzer is shut down and primed if the action has
been set to priority.
• REMOTE INHIBIT - (programmable input 1 only): The volt-

free contact to this input has to be closed to allow the electrolyzer to
run. If the contact opens, the electrolyzer is inhibited and, if currently
running, it is shut down and primed.
1.6 Operator Terminal
An operator terminal (see paragraph 3.2) allows operator access to the

PLC. Fitted to the front door panel, the terminal is equipped with a keypad
and a four-line display screen. The keypad is arranged in three groups of

®
OSEC CONTROL PANEL
keys, two on the left-hand side of the terminal and a group of mostly
number keys on the right-hand side. These key groups are used as follows:
1.6.1 Function Keys
At the top left-hand side of the operator terminal keypad are six function
keys that are used to control the generation of sodium hypochlorite. These
keys are labeled:
• TOP-UP/NEXT - One function of this key is to initiate a tank top-up

cycle. The PLC will start a fill before the low start level is reached
and fill the tank to the stop level or until the TOP-UP key is pressed
again. ‘TOP-UP’ appears in the overview display instead of ‘GEN-
ERATING’. A second function is to move the display on to show the
next event in the log.
The TOP-UP function is not available while the Event Log menu is
selected at the terminal. The NEXT function key operates only when
the Event Log menu is selected at the terminal display.
• RESET - Press this key to reset the OSEC system after an alarm
condition is cleared and restart the system (subject to tank level).
NOTE: The RESET key is active only after the ALARMS LIST key
is pressed and the list is displayed.
• BACK - This key is used to return the display to the previous level
and will function in all menus.
• AUTO/PREV - This is a dual-function key that operates in the fol-

lowing way:
Pressing the AUTO function key will set the OSEC system for auto-
matic start/stop operation as determined by the storage tank level
transmitters.
In the overview display, the word ‘AUTO’ is displayed when the

electrolyzer is not running and ‘STARTING’, ‘GENERATE’, ‘TOP-
UP’, ‘PRIMING’, or ‘PURGING’ when the appropriate cycle is in
progress. This key will not function in the Event Log menu.
The PREV function will operate only in the Event Log menu where,
by pressing this key, the present event shown at the display will move
backward to show the previous event in the log.

®
OSEC CONTROL PANEL
• INHIBIT - This key is pressed in any menu to prevent the OSEC

from generating hypochlorite. The word ‘INHIBIT’ appears in the
overview display. The alarm system remains active.
• FLUSH - Pressing this key, in any menu, will turn on the water sup-
ply and leave it on until two complete changes of water have passed
through the electrolyzer. The time this will take is determined from
the parameters entered during the configuration procedure. The word
‘FLUSH’ appears in the overview menu when selected, ‘FLUSH-
ING’ appears while running, and ‘FLUSHED’ appears when the cycle
is complete.
A flush terminates immediately if the storage tank high level contact

operates, if a tank overflow is detected, or if there is a low water flow
alarm. The flush is also terminated if INHIBIT is selected. In this
mode, alarms are monitored as in the inhibit mode.
1.6.2 Display Keys
The lower six keys of the left-hand section of the operator terminal keypad
are associated with the display itself and are used to select the following:
• ALARM LIST - As soon as it occurs, every alarm condition is writ-

ten to the ALARM LIST, along with the date and time. Pressing this
key silences the audible and displays the LIST for the alarm to be
identified
• MAIN MENU - Comprises the system’s two basic displays (see Dwg.
85.030.190.010, located in Section 3). Whenever this key is pressed,
regardless of the menu displayed, the Main menu is displayed:
Main Menu
! Status Display
! Other Functions
The four remaining keys ("!#$) are used to move the display
cursor in the appropriate direction to select the required item, i.e., to
scroll through the Alarm List.
Refer to paragraph 3.2 for further information on the operator terminal.
1.7 Tank Level
Product level in the storage tank is transmitted to the control panel from
a hall effect pressure transducer as a 0 to 20 mA signal. At the panel, this
®
OSEC CONTROL PANEL
signal is applied to an analog input of the PLC and also to a signal isolator
for re-transmission purposes.
Day start, day stop, night start, night stop, and low storage level are all set
in the ‘storage levels’ menu at the operator terminal display.
The current storage tank level is indicated at the ‘overview’ display.
1.8 Event Log
Every event (e.g., electrolyzer start-up, shut down, alarm, etc.) is stored
in the event log along with the date and time record of when it occurred.
The event log is viewed by accessing the ‘event log’ menu and selecting
‘view event log’.
The storage area for the event log is limited to 200 entries and, once full,
the oldest entries are replaced by the new records.
To clear and reset the event log, access the ‘event log’ menu and select
‘clear event log’. A password is needed to carry out this action.
1.9 Room Ventilation
Two types of room ventilation monitoring are available, one of the two is
selected during the configuration procedure.
• ROOM VENTILATION AVAILABLE: A volt-free contact within

the customer’s ventilation control system is monitored for system
availability. This contact should be closed when the ventilation sys-
tem is available and healthy. The contact is checked prior to
electrolyzer start-up and, if open, start-up is inhibited. It is also checked
while the electrolyzer is running and, if open, the electrolyzer is shut
down and primed.
• ROOM VENTILATION RUNNING: A volt-free contact from the

customer’s ventilation control system is monitored for correct opera-
tion. It has one minute to reach the closed state on start-up. If this
contact should fail to close or should open while the electrolyzer is
running, the electrolyzer is shut down and primed.
1.10 Tandem Link
The control panel has a facility that enables two control panels to be linked
together (four wires) to allow a common start. This is used when two
®
OSEC CONTROL PANEL
separate OSEC systems are installed and the two product tanks are joined
together by either a balance pipe or a bus main for the dosing pumps.
When one OSEC system reaches the active start level, it starts its own
electrolyzer and sets its ‘system filling’ output high. Each panel monitors
an ‘other system filling’ input and, if it detects that the other system has
started (input going high), it waits five seconds (ignoring its own start
level) before going into its own start sequence. Whichever way an
electrolyzer is started, it is stopped by reaching its own active stop level.
Each OSEC will start its rectifier only on its 10-second synchronization
pulse (this being started by reaching the start level) and, as the link start
is delayed by five seconds, there will always be at least a five-second delay
between the start-up of two rectifiers on a linked system.
1.11 Dosing Pump Enable
The ‘dosing pump enable’ relay is continuously energized while the prod-
uct level in the hypochlorite storage tank is above the set low storage level.
1.12 Electrolyzer Running Relay
An ‘electrolyzer running’ relay is energized whenever the electrolyzer is

generating sodium hypochlorite. This provides a volt-free contact for
customer telemetry.
1.13 Monitor
Accessed by entering the ‘Monitor’ menu of the operator terminal and

selecting the parameter type that you wish to view, the monitor allows the
operator to see what is happening within the PLC software by examining
the state of the data registers, auxiliary relays, timers, and counters. This
is a ‘view only’ facility.
1.14 Information
The information menu allows the operator to view certain information

about the current status of the system and its history.
In the ‘Process times’ menu, the current status of various processes is

displayed enabling the operator to see, for example, how long the current
generation has been running, how long since the last generation ended, or
how much time remains for the prime or purge cycles to run.

®
OSEC CONTROL PANEL
The ‘Hours run’ menu displays in hours and minutes the total run time for
the brine pumps, blowers, and transformer/rectifier. These can be reset
from a password-protected reset menu.
1.15 Help
The ‘Help’ menu provides access to various text-based help screens.
1.16 Hydrogen Detection (Optional)
A set of hydrogen detection equipment can be fitted to monitor the atmo-

sphere in the vicinity of the electrolyzer and provide alarms should the
hydrogen concentration exceed a preset level, signifying that a leakage
has occurred. The detection unit supplied comprises a control box and a
separate gas sensor unit. The control box is located in the OSEC control
room and the sensor is mounted close to and above the electrolyzer. The
control unit is powered from a 110/240V, 60 Hz, single-phase mains
supply and is fitted with a three-digit liquid crystal display. This is cali-
brated in percent LEL (Lower Explosive Limit) and ranges from 0 to
100% to continuously indicate the concentration of any gas detected.
The unit provides two alarm outputs for high and low alarms, and the set
points are individually adjustable in the range of 5% to 65% of full scale.
An equipment fault alarm output is also provided for customer use.
In the event of a low-level alarm occurring, an audible alarm is sounded

and an alarm lamp is lit at the control unit. Together with these local alarm
indications, a signal is provided to the OSEC control cabinet to light the
Hydrogen Leak alarm lamp and to shut down the electrolyzer system. For
full details, refer to the manufacturer’s information supplied with the
equipment.

®
OSEC CONTROL PANEL

®
OSEC CONTROL PANEL
SECTION 2 - INSTALLATION
List of Contents
PARA. NO.
General...................................................................... 2.1
Connection Details ................................................... 2.2
Configuration ............................................................ 2.3
Low Cost Electricity ................................................. 2.4
2.1 General
It is recommended that the control panel is wall-mounted remote from the

electrolyzer in an area where it will not be subject to any water or chemical
splashes and where the temperature is between 41°F (5°C) and 105.8°F
(40°C). The enclosure is secured to the wall by four screws in adjustable
brackets fitted to the rear of the case at the corners. These brackets can be
positioned so that they extend vertically at the top and bottom edges of the
enclosure, or alternatively, extend horizontally at the left- and right-hand
sides of the case.
2.2 Connection Details
The control requires a 110V or 240V, 60 Hz, single-phase mains supply,

depending upon customer stipulation at time of ordering. The control
voltage is not selectable on site. The mains supply to the control must be
taken from a fused switch unit mounted within 6.5 feet (2 meters) of the
control. The switch should be fused at 10A for the 110V supply or 5A for
240V supplies.
WARNING: MAINS VOLTAGES CAN KILL. ENSURE THAT THE

! SUPPLY IS ISOLATED ELSEWHERE BEFORE MAKING THE
CONNECTIONS.
The control connects directly to the electrolyzer by a six-wire intrinsically

safe cable and two three-wire screened cables, one for the high-tempera-
ture sensor and one for the low-temperature sensor. The dilution water
inlet solenoid valve for the electrolyzer is also connected by a three-wire
cable to the control.
In addition to the connections with the electrolyzer, the control panel

requires further connections with the other items of the plant that form the
electrolyzer system:
®
OSEC CONTROL PANEL
• Starters of the remote mounted duty/standby brine pumps for the stop/
start signals;
• The storage tank equipment of level switches, level transmitter, hy-

drogen blowers local starters for duty/standby blowers, low air flow,
and the tank overflow alarm switch.
The tank level switch circuits are designated intrinsically safe and should
be run separately from other cables.
All electrical cables between the panel and the various units must be
installed in accordance with the latest edition of the I.E.E. regulations for
electrical installations and must conform to local electrical codes. The
external connection diagram (Dwg. 85.035.140.010) shows the cabling
and stipulates the minimum sizes of cables to be used. Where any cables
are designated intrinsically safe, such cables must be run separately from
other mains cables and have a blue-colored outer sheath to signify their
status. These cables must have 500V insulation and must be metal-sheathed
or armored where there is a risk of mechanical damage, or if they are being
run in the same ducting as other cables.
Conduits that terminate in the hazardous area above the tank must employ
approved glanding incorporating seals to prevent fumes or flames from
travelling through the conduit.
2.3 Configuration
Prior to operation, the control software is configured to suit the system

being installed and the following information must be entered or selected:
• OSEC type (B1-150, B1-200, B2-200, or B4-200) and its anode quan-
tity must be entered in order to set the prime, flush, and cell fill times.
• Storage tank capacity (liters at 20 mA input) along with the fill start/
stop levels and their corresponding alarm levels.
• The number of storage tank blower units available to the controller

must be selected between one or duty and standby operation.
• Room ventilation monitoring must be selected, e.g., between ‘avail-

able’ and ‘running’.
• The number of brine pumps available to the controller must be se-

lected between one or duty and standby operation.

®
OSEC CONTROL PANEL
• The brine pump start-up inhibit time (between 30 and 300 seconds).
• The three programmable alarm inputs.
• The use of low-cost electricity (see paragraph 2.4) and the time dur-
ing which that applies.
2.4 Low-Cost Electricity
The system can be configured to use electricity on the during low-usage,

and thus low-cost, periods. If this option is set, a large fill is performed
overnight and small fills, if required, are allowed during the day.
The PLC clock is used to determine whether the low-cost period is cur-
rently applicable by referring to the low-cost electricity start and end times
set by the user.
If the low-cost electricity option is set and the system is still running at the
end of the low-cost period, the system will continue to run until the day-
time stop level is reached. Should that level have been reached already, the
system is stopped.
At the beginning of the low-cost electricity period, the system is started

regardless of the storage tank level, stopping when the nighttime stop
level is reached.

®
OSEC CONTROL PANEL

®
OSEC CONTROL PANEL
SECTION 3 - OPERATION
List of Contents
PARA. NO.
Initial Start-Up ..................................................... 3.1

Operator Terminal Display .................................. 3.2
Status Display ...................................................... 3.3
Other Functions Display ...................................... 3.4
System Malfunction ............................................. 3.5
Temporary Shut Down ........................................ 3.6
Complete Shut Down .......................................... 3.7
Failure of Electrical Power .................................. 3.8
3.1 Initial Start-Up
With the initial start-up procedure of the electrolyzer fully completed (as
detailed in paragraph 3.1, steps a through h, of the main instruction manual),
the control panel can be brought into operation.
a. Before start-up, check that all ventilators in the plant room are open.
b. Check that the sample/drain valve on the electrolyzer is closed and

that the storage tank drain valve is closed.
c. Ensure the valve on the water supply to the water softener is open.
d. At the Control Cabinet, set the Main Incomer supply selector switch
to ON and check that its SUPPLY ON lamp illuminates. Set the mains
isolator for the transformer/rectifier to the ON position and check
that its SUPPLY ON lamp lights.
e. At the operator terminal, the Main menu is displayed.
3.2 Operator Terminal Displays (See Dwg. 85.030.190.010)
After power-up, the operator terminal screen displays the Main menu.
This display is returned to the screen from any other display by pressing
the MAIN MENU key. The display allows the operator to scroll through
the complete range of menus. The Main menu comprises:
! Status Display
! Other Functions
®
OSEC CONTROL PANEL
At the display, only four lines of information are seen at any one time and
where there are more lines the ‘+’ sign is used to show this. The lines
appear as the cursor is scrolled down and then up again.
3.3 Status Display
Ensure the flashing cursor is level with the words ‘Status Display’, then
press the Enter key. The following display appears on the screen:
Product: # # # # #L # # #%
In: # # °C Water : # # #
Out: # # °C Brine : # # #
(state) Blow : # # # #
This display remains on the screen during normal working conditions and
shows, in liters, how much sodium hypochlorite the storage tank contains
and what percentage of the tank this amount fills.
Also displayed is the temperature of the water at the electrolyzer inlet; the
temperature of the product at the OSEC outlet; the status of the water
supply (on or off); the status of the brine supply (on or off); and the status
of the blower (on or off). This display gives the current operating mode of
the OSEC unit (purging, etc.). The screen is read-only and does not have
a cursor.
Press the BACK key, or the MAIN MENU key, to go back to the Main
menu display. Set the cursor level with the ‘Other Functions’ line and
press the Enter key.
3.4 Other Functions Display
The Other Functions display provides access to all other functions of the
OSEC control system, which comprise the following menus:
! Help
! Duty Select
! Storage Levels +
! Time/Date
! Configuration
! Information
! Event Log
! Monitor

®
OSEC CONTROL PANEL
3.4.1 Help Display
With the cursor on the arrow next to the ‘Help’ line, press the Enter key.
The following menu appears:
! Number of Anodes
! Cheap Rate Power
! Alarms
! Prog. Inputs +
! Information
! Event Log
! Monitor
This menu enables the operator to obtain help about the associated OSEC
and its control system. It cannot be used to make changes to any of the
control settings.
3.4.2 Duty Select Menu
When dispatched, the control parameters may already be selected and set
into the controller, requiring no changes; however, if any changes are
required regarding the selection of the duty/standby status of the brine
pump or hydrogen blower, this menu is used. Select which brine pump
shall operate as the No.1 (duty) unit and which hydrogen blower shall
serve as the No.1 (duty) unit by placing the cursor against the desired
pump or blower and pressing the Enter key. The display will show the
change from the present No.1 to No.2 or back again.
3.4.3 Storage Levels Menu
This menu allows changes to be made to the existing control settings with
respect to the tank fill START and STOP levels. The START levels for
both the daytime fill and the nighttime fill are shown as a percentage of
the storage tank volume. The STOP levels for both the daytime fill and the
nighttime fill are also shown as a percentage of the storage tank volume.
The storage tank low-level alarm is also set in this menu.
3.4.4 Time/Date Menu
The time and date are set in the PLC prior to dispatch from the factory, but
if a change is needed this menu is used. To alter the existing time/date
settings, use the arrow keys to position the cursor over the figures to be
changed and type in the new settings.

®
OSEC CONTROL PANEL
3.4.5 Configuration Menu
When the OSEC system is dispatched, the control parameters associated

with the system will already have been entered in the PLC; however, the
final operating data may be entered during the commissioning stage. When
this is the situation, the changes are made in this menu, which comprises
the following sub-menus:
• OSEC type: Type of electrolyzer, i.e., B1-200. This selection is made

prior to dispatch by the manufacturer; however, if it is necessary to
select the appropriate OSEC type, press the Enter key when this dis-
play appears—do not move the cursor. A list of OSEC types will
appear. Move the cursor to the required type and press the Enter key
to accept the new selection.
• No. of Anodes: This data is also set before dispatch, but this figure
can be altered by using the number keys and then entering the new
figure.
• Tank cap.: This figure can be altered by using the number keys and
then pressing Enter to save the figure.
• No. Blower: Either a single hydrogen blower is used in the OSEC

system or two blowers are arranged for duty and standby operation.
• Room Vent: A selection is made between AVAILABLE and RUN-

NING using the Enter key to toggle between either of these remote
customer contacts.
• No. Brine: This menu allows selection between SINGLE and DUTY/
STANDBY operation using the Enter key to toggle between the single
or duty/standby configuration.
• Brine start: This menu relates to the number of seconds the brine
flow alarm start-up inhibit will last. Use the number keys and then
press the Enter key to save the figure.
• Cheap rate: Provides the operator with the option of making use of
low-cost electricity, if desired. If NO is already selected, press the
down arrow key to skip this and the next item on the menu. If select-
ing YES (the Enter key is used to toggle between YES and NO), the
following item is also selected.
• Cheap rate period: Access the cheap rate START time by pressing
Enter. First use the number keys to select the hour and press the En-
®
OSEC CONTROL PANEL
ter key to select it, then select the minutes and press the Enter key to
select them. Repeat the procedure for the END time and then press
the BACK key to return to the Configuration menu and the next item.
• Set-up prog inputs: Three programmable inputs are provided that

may be used to feed signals into the OSEC controller. Each input is
connected to a selected contact in the OSEC system. Press the Enter
key to move to the Set Type menu and press the key again to display
the input list.
With the cursor against No.1, press the Enter key and a list of items
will appear at the left side of the menu. From this list, select one of the
following choices and press the Enter key to select it:
OFF - Not used

RELIEF - Relief valve operating
SATOVER - Saturator overflow
SOFTENER - Softener has failed
AUX. 1 - Aux. alarm No. 1 has operated
INHIBIT - Used to inhibit OSEC control
NOTE: The choice of INHIBIT is available only in ‘Programmable

Input No.1’ and must therefore be selected here if it is required.
Repeat the procedure with input No.2 and input No.3. If the Auxiliary
Alarms associated with the inputs are not selected, skip the next item
on the menu and return to the Main menu.
If an Auxiliary Alarm is selected in the inputs menu, press the BACK

key and the Enter key to select the next menu.
• Configure Aux.: The OSEC control has three auxiliary alarms that
are configured to operate when a customer-specified alarm condition
occurs. To set the alarm, use the number keys to select the alarm
delay time (time lapse between the alarm occurring and its display)
and press the Enter key.
Next use the Enter key—which will toggle between CONTINUE (i.e.,
continue generating) and STOP (i.e., stop generating)—to set the
desired control action in the event of this alarm. Press the BACK key
until the Information menu appears in the display.
3.4.6 Information Menu
Press the Enter key to obtain the PROCESS TIMES menu.

®
OSEC CONTROL PANEL
NOTE: This menu can only provide the operator with information
about the current status of the electrolyzer unit, it cannot be used to
make changes to the unit’s control settings. Pressing either the Enter
key or the down arrow key will allow the operator to scroll through
the following information:
• This Gen: If the electrolyzer is running, the time it has been running
is shown here.
• Since Gen: Providing the electrolyzer is not running, this display

will show how much time has elapsed since it last ran, otherwise this
display will show zero.
• End Prime: If the prime cycle is active, this display shows how much
time remains until the cycle ends; otherwise this display will show
zero.
• End Purge: This display shows how much time remains until the
purge cycle will end if it is active; otherwise this display will show
zero.
• Prime Time: This display shows the time—set by the system—that

it takes to complete the prime cycle.
• Flush Time: This display shows the time—set by the system—that

it takes to complete the flush cycle.
• Cell Fill Time: This display shows the time—set by the system—
that it takes to complete the cell fill cycle.
At the bottom of the menu press BACK to return to the Information menu
and the next sub-menu.
• Hour Run Meters: This sub-menu tells the operator how much ‘run’
time has accrued on the following items of equipment:
Brine Pump No.1

Brine Pump No.2
Blower No.1
Blower No.2
Transformer/rectifier
The operator can check these times by scrolling through the list, using
either the Enter or the down arrow key. At the bottom of the menu,
press BACK to return to the Information menu and the next sub-menu.
®
OSEC CONTROL PANEL
• Reset Hour Run: When this menu is selected (by pressing the Enter
key at the Information menu), the word ‘PASSWORD’ is displayed.
If the password is not known, press the Enter key to return to the
previous menu, then press BACK to go on to the next menu.
3.4.7 Event Log Menu
• Event Log: Events that occur during the OSEC operating cycle are
recorded by the PLC, which gives each event a number, notes the
date and time, and describes the event. Use the arrow key to scroll
through the list and press LAST to pass on to the next display.
• Clear Event Log: When this menu is selected (by pressing the Enter
key at the ‘Event Log’ display), the word ‘PASSWORD’ appears. If
the password is not known, press the Enter key to return to the previ-
ous menu, then press BACK to go on to the next menu.
3.4.8 Monitor Menu
The Monitor menu provides a facility similar to a diagnostics-type tool

and is provided essentially for use by USF/W&T service engineers. The
menu allows access to four types of data, each of which is denoted by a
letter (i.e., ‘D’ for Data Register, ‘M’ for Aux Relays, ‘T’ for Timers, and
‘C’ for Counters). Press the Enter key to reach the next display.
• Data Reg’s: The letter ‘D’ is used to identify the Data Register menu,
where two identical columns are displayed. Each column represents
two separate addresses where data is registered. Each address is
headed by the letter ‘D’ and contains two consecutive data registers.
Alongside the letter ‘D’, type in the address of the data to be monitored
and press the Enter key. Typically, the following information will
appear in the display:
Example:
D235 (the address of the data register)

+ 0 = 2522 (the data registered at address box 235)
+ 1 = 27 (the data registered at the next consecutive address
box, i.e., address box 236)
The second column allows a second address to be accessed.
• Aux Relay: Identified by the letter ‘M’, the Aux. Relay menu dis-
plays two lines of places, one above the other. Each line allows ac-
®
OSEC CONTROL PANEL
cess to the address of an auxiliary relay. On each line, the first four
places to the left of the colon (:) are used to key-in the address of the
auxiliary relay to be monitored.
The first place to the right of the colon shows the state of the relay at
the address selected, while the next seven places show the state of the
relays at the next seven consecutive addresses.
The following example shows that the auxiliary alarm at address 362
(underlined) is ‘off’ and shows the state of the relays at the consecutive
addresses as: 363 is ‘off’, 364 is ‘off’, 365 is ‘on’, 366 is ‘on’, 367 is
‘off’, 368 is ‘on’ and 369 is ‘on’.
M
0362 : 0 0 0 1 1 0 1 1
• Timer: This menu, identified by the letter ‘T’, displays two lines of
places, either of which can be used to key-in the address of a timer.
The address is keyed-in on the left-hand side of the ‘=’ sign and the
Enter key is pressed to accept it. On the right of the ‘=’ sign, the
content of the selected address is displayed. If the timer is running, it
is shown—in operation—at the display. If the timer is not running,
the display will show a zero.
• Counter: This menu, identified by the letter ‘C’, displays two lines
of places, either of which can be used to key-in the address of a counter.
The address is keyed-in on the left-hand side of the ‘=’ sign and the
Enter key is pressed to accept it. On the right of the ‘=’ sign, the
content of the selected address is displayed. If the counter is running,
it is shown—in operation—at the display. If the counter is not run-
ning, the display will show zero.
• A/D Channel: Identified by the letter ‘D’, this menu is used to dis-
play the value of three 0 to 20 mA analogue inputs. One input comes
from the tank contents-level transmitter, one from the water tem-
perature sensor fitted to the OSEC inlet, and one from the product
temperature sensor fitted to the OSEC outlet.
3.5 Electrolyzer System Malfunction
If a malfunction occurs on the electrolyzer or its associated equipment, an

audible alarm will sound at the OSEC Control. The audible alarm can be
silenced by pressing the ‘ALARM LIST’ key, which will indicate the
source of the alarm, followed by the ‘ALARM ACK’ key. The alarm will
remain until the fault condition is cleared and the ‘RESET’ button is
®
OSEC CONTROL PANEL
pressed. This action will start-up the system again, level transmitter at the
storage tank permitting.
Certain alarm conditions result in a total system shut down, while others
only activate the associated alarm contacts and the audible alarm. Refer
to paragraphs 1.4 to 1.6 for details of alarms and their functions.
3.6 Temporary Shut Down
Following normal operation, the electrolyzer will enter a standby condi-

tion where the casing(s) will have been flushed with fresh brine. The
electrolyzer can subsequently be left for up to one week in this shut-down
condition.
If the electrolyzer has ceased to operate following an alarm condition that

does not initiate a refill cycle, the electrolyzer must be drained of the
partially electrolyzed product in order to protect the electrodes from cor-
rosive attack by hypochlorite.
3.7 Complete Shut Down
If the unit needs to be completely shut down for servicing purposes or due
to the need for associated equipment to be serviced, proceed as follows:
If shutting down from a normal inactive state in which electrolysis is not

taking place and the cell contains only brine solution, switch the mains
isolator at both the transformer/rectifier and the Control Panel to OFF.
Connect a hose to the sample/drain valve on the cell outlet and open the
valve to fully drain the casing(s). Close the valve when draining is com-
plete.
If the need arises to shut the system down during a period of electrolysis,
turn the mode selector to INHIBIT. Electrolysis will cease. The control
panel and rectifier isolators should be turned off and the cell drained as
previously described.
3.8 Failure of Electrical Power
Should a failure occur in the electrical power supply to the OSEC system
while it is generating sodium hypochlorite, and it is apparent the power
will not be restored within a maximum of three hours, the following
procedure MUST be carried out:

®
OSEC CONTROL PANEL
a. Switch off the OSEC control panel at its local electrical isolator to
ensure that, when power is restored, the OSEC control does not try to
continue where it left off, not knowing the cell casings are empty.
b. Fully drain the electrolyzed product from the electrolyzer cells. This
action is necessary to prevent corrosion of the electrode assemblies
due to reverse polarization occurring in the presence of hypochlorite.
c. On restoration of power, switch on the electrical supply to the OSEC

control panel and press the INHIBIT key at the operator terminal.
d. After a few seconds, press the AUTO key. The OSEC control will
automatically start a new cycle by filling the electrolyzer cells with
water and brine.
CAUTION: If filling the casing from a mains water supply, ensure

! that the casing is not subjected to a greater pressure than 2 bar.

®
OSEC CONTROL PANEL
SECTION 4 - SERVICE
List of Contents
PARA. NO.
Routine Maintenance ................................................ 4.1

Troubleshooting ........................................................ 4.2
4.1 Routine Maintenance
There are no routine maintenance requirements for the control cabinet,

other than to check the terminations. Ensure that the mains supply to the
cabinet is isolated elsewhere before opening the control panel.
4.2 Troubleshooting
Table 4.1 details the alarms that may occur at the OSEC control, together
with their possible causes and remedies.

®
OSEC CONTROL PANEL
Table 4.1 - Troubleshooting
FAULT CONDITION POSSIBLE CAUSE CORRECTIVE ACTION

High curre nt - Re ctifie r Short in electrolyzer or electrical C heck for shorts but do not
Fa ilure a la rm trigge re d, connections from rectifier. dismantle electrode assembly.
e le ctroly ze r s hut down. Return for servicing.
O perating on two phases only. Renew fuse in failed line.
Failure in rectifier unit. C heck and repair or replace.
Low curre nt/high ce ll Low brine concentration. C heck brine flowrate on flowmeter
v olta ge - Imprope r and adjust brine pump stroke, if
Volta ge a la rm trigge re d necessary.
a nd e le ctroly ze r s hut
down. Salt saturator water level low. C heck and adjust ball valve.
Low curre nt/high ce ll Salt level low. Fill to at least the minimum level
v olta ge - Imprope r marked on the saturator.
Volta ge a la rm trigge re d a
Salt saturator discharge blocked. Empty saturator and flush through
e le ctroly ze r s hut down.
tank and delivery lines.
Rectifier failure. C heck and repair or replace.
Electrodes require replacement. Electrodes have an operating life of
approximately five years.
Poor bus bar connection. Test voltage drop across terminals
and repair poor joints.
Low ce ll v olta ge - High brine concentration. C heck brine flowrate on flowmeter
Imprope r Volta ge a la rm and adjust brine pump, if necessary.
is trigge re d a nd
Insufficient dilution water. C heck dilution water flowrate and
e le ctroly ze r s hut down.
adjust.
Short circuit in electrode assembly. Drain electrolyzer and replace
electrode assembly. Return old unit
to USF/W&T for servicing.
High te mpe ra ture - High Dilution water flow incorrect. Readjust flow regulator valve.
Ele ctroly te Te mpe ra ture
Water flowmeter or line blocked. C lean meter and lines.
a la rm trigge re d a nd
e le ctroly ze r s hut down. Strainer blocked. C lean strainer.
Solenoid valve failure. Repair or replace.

®
OSEC CONTROL PANEL
Table 4.1 - Troubleshooting (Cont’d)

Low dilution wa te r flow - Failure of supply. C heck and remedy.
Low Wa te r Flow a la rm
Incorrect setting of pressure C heck setting. Refer to Section 3 in
trigge re d a nd e le ctroly ze r
regulator. the main manual.
s hut down.
Failure of pressure regulator. Service or replace.
Failure of solenoid valve in inlet line. Service or replace.
Jammed float in flowmeter. C lean flowmeter. Refer to Section 4
in the main manual.
Incorrect setting of minimum flow C heck and adjust - set to a 15%
switch. lower figure than correct flow. Refer
to Table 3.1 in the main manual.
Failure of switch. Service or replace.
Low brine s olution flow - Incorrect setting of brine pump. Adjust stroke. Refer to Table 3.1 in
Low Brine Flow a la rm the main manual.
trigge re d a nd e le ctroly ze r
Incorrect setting of minimum flow C heck and adjust - set to a 15%
s hut down.
switch. lower figure than correct flow (see
Table 3.1).
Jammed float in flowmeter. C lean flowmeter. Refer to Section 4
in the main manual.
Failure of switch. Service or replace.
Failure of supply to brine pump. C heck and restore.
Failure of pump. Service or replace.
Low s olution le v e l in Faulty reed switch in hypochlorite. Replace manifold.
e le ctroly ze r - Low
Ele ctroly te Le v e l a la rm
trigge re d. Faulty connection. C heck and repair.
Low te mpe ra ture - Low Heat exchanger not in use. O pen exchanger feed and return
Wa te r Te mpe ra ture (50°F valves on electrolyzer.
(10°C)) a la rm trigge re d
Heat exchanger bypass valve open. C lose valve.
with no furthe r re s pons e ,
or (49.1°F (9.5°C)) a la rm Site mains water excessively low Investigate causes. Refer to the
trigge re d a nd unit s hut temperature. main manual for temperature
down. requirements.

®
OSEC CONTROL PANEL
Table 4.1 - Troubleshooting (Cont’d)

Incorre ct a irflow into Blower supply failed. C heck and restore.
ta nk - duty blowe r fa ils ,
O perating on two phases. Renew fuse in failed line.
s ta ndby blowe r s ta rts -up.
Blower faulty. Service or replace.
Incorre ct a ir flow into General supply failure. C heck and restore.
ta nk - s ta ndby blowe r
Piping to air flow switch C heck and repair.
fa ile d a la rm, e le ctroly ze r
disconnected.
s huts down.
Blockage in air intake. C heck and remedy.
Faulty wiring. C heck and restore.
Fa ulty a irflow s witch - Air Faulty switch - contacts not Service or replace.
Flow Switch Fa ile d a la rm opening.
trigge re d - e le ctroly ze r
not in ope ra tion. Short in wiring. C heck and repair.
Ex tra high le v e l or Failure of High Stop. C heck and replace.
dis cha rge from ta nk -
Fault in control. C heck and repair.
Ov e rflow Ala rm trigge re d
a nd e le ctroly ze r s hut Mechanical damage to tank causing C heck and repair.
down. leak.
Low le v e l in ta nk - Low C ontrol panel off. Switch on.
Le v e l Ala rm trigge re d
C ontrol in inhibit mode. Switch to Auto.
a nd a s s ocia te d dos ing
pump inhibite d. Faulty low start. Service or replace.

®
OSEC CONTROL PANEL
SECTION 5 - ILLUSTRATIONS
List of Contents
DWG. NO
Control Panel - General Arrangement ................ 85.030.000.010A&B

External Connection ........................................... 85.035.140.010
Menu Structure Tree ........................................... 85.030.190.010A,B,C

®
OSEC CONTROL PANEL
OSEC® SYSTEM - CONTROL PANEL

- GENERAL ARRANGEMENT
85.030.000.010A
ISSUE 0 10-97
®
OSEC CONTROL PANEL
KEY PART NO. QT Y DESCRIPT ION KEY PART NO. QT Y DESCRIPT ION
1 AUK.3181 1 Panel heater (20W) 8 AUK.5788 1 Signal convertor, 4-20mA/4-20mA
AQA.3663 2 Screw, M4 x 8 9 AAA.3679 1 Temperature convertor, RTD/mA
ASG.4388 2 Washer, M4 10 AAA.3679 1 Temperature convertor, RTD/mA
2 AAA.3685 1 Transformer, 230/110V 11 AQA.4210 1 Interface unit, 3 channel
AXS.4368 4 Screw, M4 x 8 12 AAA.1132 1 Fuse 2A, F1, F3 and F6
ASG.4388 4 Washer, M4 AAA.1144 Fuse 5A, F2
3 AXQ.4252 1 Power supply unit, 24V DC 24A AAA.1123 1 Fuse 1A, F4
AQA.3663 4 Screw, M4 x 8 AAA.1129 1 Fuse 1.6A, F5
ASG.4388 4 Washer, M4 13 AWO.4046 14 Relay, 1 pole c/o 24 VDC
4 AAA.1174 1 Programmable Logic Contllr, FX-32MR ATI.3989 14 Rela
AUK.3691 4 Screw, M4 x 16 14 AAA.3676 1 Operator terminal, MAC50/ML
ASG.4388 4 Washer, m4 AXS.4261 4 Nut, M4
5 AAA.1156 1 Thermostat, +5 to +55°C ASG.4388 4 Washer, M4
AAA.2241 2 Screw, M4 x 12 15 AWO.3817 1 Audible alarm
ASG.4388 2 Washer, M4 16 ARE.3983 1 Indicator
6 AAA.3673 1 Analog input 4 channel FX-4AD ARE.3995 1 Screen, flat white
AUK.3691 2 Screws, M4 x 16 ATI.4276 1 Lamp, 28V T1-3/4 1.12W
ASG.4388 2 Washer, M4 AAA.2718 1 Label (MAINS ON)
7 AUK.4146 1 Mains isolator switch 17 AAA.2625 1 Enclosure
AAA.1314 4 Screw, M4 x 12 AAA.7759 4 Enclosure bracket
ASG.4388 4 Washer, M4 AAA.2715 1 Label (OSEC CONTROL PANEL)
OSEC® SYSTEM - CONTROL PANEL

- GENERAL ARRANGEMENT
85.030.000.010B
ISSUE 0 10-97
®
OSEC CONTROL PANEL
OSEC® SYSTEM -
EXTERNAL CONNECTION
85.035.140.010
ISSUE 0 10-97
Supplement 1 (B/7-00)
MAIN MENU SUB-MENUS

---MAIN MENU---+ Product:#####L ###% Current storage tank level in liters &
» Status Display | percent
In:##°C Water:### Inlet temperature and water solenoid valve
OSEC® SYSTEM - CONTROL PANEL - MENU STRUCTURE TREE
status
OSEC CONTROL PANEL

Out:##°C Brine:#### Outlet temperature and brine pump status
(state) Blow:#### Current system state and blower status
» Other Functions | » Help HELP:
------------------------+ » Number of Anodes Display help text on the number of anodes
fitted
®
» Cheap Rate Power Display help text on the cheap rate electric
option
» Alarms Display help text on the alarm system
» Prog. Inputs Display help text on the programmable
inputs
CP-39
» Information Display help text on the information

displays
» Event Log Display help text on the event logger
» Monitor Display help text on the monitor
» Duty select Selected for DUTY
Brine pump : ???? Brine pump selected for duty - Toggle

No.1/No.2
Blower : ???? Blower selected for duty - Toggle
No.1/No.2
» Storage levels Day Night
Start: ??% ??% Storage tank fill start levels for day & night
Stop: ??% ??% Storage tank fill stop levels for day & night
Low alarm: ??% Storage tank low alarm level
» Time / Date Time : ##:##:## Current time - Overtype to change
85.030.190.010A
Date : ##/##/## Current date - Overtype to change

ISSUE 1
7-99
» Configuration OSEC type : ?????? Type of electrolyzer - Select from list

No. Anodes : ??? Number of Anodes fitted in the
electrolyzer
Tank Cap. : ?????L Storage tank capacity in liters
No. Blower : ??????? Number of storage tank Blowers -
Toggle SINGLE / DUTY/STANDBY
Room Vent : ??????? Type of room vent monitoring -
Toggle AVAILABLE / RUNNING
No. Brine : ??????? Number of Brine pumps -
Toggle SINGLE / DUTY/STANDBY

Brine Start : ???sec Brine flow alarm start-up inhibit time
OSEC CONTROL PANEL

Cheap rate : ??? Use cheap rate electric option - Toggle
YES / NO
» Cheap rate period Cheap Rate Period
Start - ??:?? Set start of cheap rate electricity period
End - ??:?? Set end of cheap rate electricity period
®
(24-hour clock)
» Set-up prog inputs Programmable input Prog. input type
» Set Type No.1 : ??????? Definition of input No.1 - Select from
list
CP-40
No.2 : ??????? Definition of input No.2 - Select from

list
No.3 : ??????? Definition of input No.3 - Select from
list
» Configure Aux Auxiliary Alarm
» Configure No. 1 Auxiliary Alarm No.1
Delay : ??? sec Delay before alarm No.1 is displayed &
actioned
Action : ??????? Choice of CONTINUE or STOP on
» Configure No. 2 alarm
Auxiliary Alarm No.2

» Configure No. 3 actioned
alarm
85.030.190.010B
Auxiliary Alarm No.3

actioned
ISSUE 0

alarm
7-99
INFORMATION
» Process Ti mes PROCESS TIMES
Thi s Gen. ###:##:## Ti me uni t has been runni ng (i f on)
Si nce Gen ###:##:## Ti me si nce uni t last ran (unless runni ng)
End Pri me ##:## Ti me unti l end of pri me cycle (i f acti ve)
End Purge ##:## Ti me unti l end of purge cycle (i f acti ve)
Pri me Ti me ##:## Pri me ti me (set by the system)
Flush Ti me ##:## Flush ti me (set by the system)
Cell Ti me ##:## Cell fi ll ti me (set by the system)
» Hours Run Meters HOURS RUN METERS
Bri ne 1 Bri ne pump No.1 run ti me - hrs:mi ns
Bri ne 2 Bri ne pump No.2 run ti me - hs:mi ns
Blower 1 Blower No.1 run ti me - hrs:mi ns
Blower 2 Blower No.2 run ti me - hrs:mi ns
OSEC CONTROL PANEL

Trans/Rect Transformer/Recti fi er run ti me -hrs:mi ns
» Reset Hour Run HOURS RUN
RESET
Meter = ??????? Meter to reset - Select from li st
Reset = ??? Confi rm reset
®
» Event log EVENT LOG
(### entri es)
» Vi ew Event Log ### ##/## ## : ## : ## Record number - Date - Ti me
################ Event descri pti on
### ##/## ## : ## : ## Record number - Date - Ti me
CP-41
################ Event descri pti on

» Clear Event Log Event log last clear Last event log clear ti me & date
at ##:## on ##/##/##
Clear Log now? ??? Confi rm log clear

» Moni tor » Data regi ster (D) Moni tor - Data Reg's
D???? D???? Data regi ster addresses to vi ew
+0=##### +0=##### Data at speci fi ed regi ster addresses
+1=##### +1=##### Data at speci fi ed regi ster addresses+1
» Aux Relay (M) Moni tor - Aux Relays
'M' : next 7 values
####:# # # # # # # # Address : State of 8 Auxi li ary relays
from addresses
####:# # # # # # # # Address : State of 8 Auxi li ary relays
from addresses
85.030.190.010C
» Ti mer (T) Moni tor - Ti mers

T??? = ##### Ti mer address & current value
T??? = ##### Ti mer address & current value
» Counter (C) Moni tor - Counters
ISSUE 0
C??? = ##### Counter address & current value

C??? = ##### Counter address & current value
» A/D Channel Moni tor - A to D
Channel : ??????? Channel to vi ew - Select from li st
7-99
Value : #### Current value of selected channel

3-4170-7-1617181789 - OSEC Manual

Uploaded by

Copyright:

Available Formats

3-4170-7-1617181789 - OSEC Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3-4170-7-1617181789 - OSEC Manual

Uploaded by

Copyright:

Available Formats

B1-150

BOOK NO. IM 85.010AA UA ISSUE C

EQUIPMENT SERIAL NO. _________________

DATE OF START-UP _____________________

Prompt service available from nationwide authorized service contractors.

WALLACE & TIERNAN PRODUCTS

IM 85.010AA UA (C/3-01) 1.010-42D

The OSEC® (On Site Electrolytic Chlorination) hypochlorite generation

This manual describes the B1-150 OSEC system, producing outputs of

U.S. Filter/Wallace & Tiernan’s (USF/W&T) guarantee is conditional

WARNING: TO PREVENT POSSIBLE PERSONAL INJURY OR

NOTE: When ordering material, always specify model and serial

IM 85.010AA UA (C/3-01) Introd.

Very Important Safety Precautions ........................... SP-1,-2,-3

IM 85.010AA UA (C/3-01) Introd. (Cont’d)

VERY IMPORTANT SAFETY PRECAUTIONS

PERSONNEL MUST BE MADE AWARE OF THE DANGERS OF HANDLING CONCENTRATED

THE STRENGTH OF THE HYPOCHLORITE SOLUTION GENERATED BY THE OSEC UNIT

IM 85.010AA UA (C/3-01) SP-1

VERY IMPORTANT SAFETY PRECAUTIONS (CONT’D)

THE ELECTRICAL POWER IN THIS EQUIPMENT IS AT A VOLTAGE HIGH ENOUGH TO

WHEN SUPPLIES CANNOT BE DISCONNECTED, FUNCTIONAL TESTING, MAINTENANCE

THE PROCESS OF CONVERTING BRINE INTO SODIUM HYPOCHLORITE GENERATES HY-

NO ATTEMPT MUST BE MADE TO EXTRACT SODIUM HYPOCHLORITE AT ANY POINT

TO AVOID POSSIBLE SEVERE PERSONAL INJURY OR EQUIPMENT DAMAGE, OBSERVE

THIS EQUIPMENT SHOULD BE INSTALLED, OPERATED, AND SERVICED ONLY BY TRAINED

VERY IMPORTANT SAFETY PRECAUTIONS (CONT’D)

DO NOT DISCARD THIS INSTRUCTION BOOK UPON COMPLETION OF INSTALLATION.

ADDITIONAL OR REPLACEMENT COPIES OF THIS INSTRUCTION BOOK ARE AVAILABLE

USFILTER’S WALLACE & TIERNAN PRODUCTS

IM 85.010AA UA (C/3-01) SP-3

NOTES ON PROTECTIVE EQUIPMENT AND CLOTHING

WARNING: WHEN DEALING WITH HAZARDOUS MATERIAL, IT

It is good general practice to make use of 1. Goggles, flexible

IM 85.010AA UA (C/3-01) 1.010-6C

ANODE WARRANTY CONDITIONS

d. The electrolyte must contain less than 2 mg/l fluoride (F).

h. Salt quality must be to the following specifications:

Water insolubles: 0.01% maximum

j. Protective current is to be maintained and applied according to the Instruction Manual.

IM 85.010AA UA (C/3-01) AW-1

INSTALLATION, OPERATION, MAINTENANCE, AND SERVICE INFORMATION

1901 West Garden Road

250 Royal Crest Court 243 Blvd. Brien

Via Jose Lopez Portillo 321

IM 85.010AA UA (C/3-01) 1.010-1D

SECTION 1 - TECHNICAL DATA

General Description .............................................. 1.1

1.1 General Description

An OSEC system is designed to produce a supply of sodium hypochlorite

• Water Softener — Provides the softened water supply to the brine

• Salt Saturator — Produces the concentrated brine solution used by

• Electrolyzer — Generates the hypochlorite solution.

• Transformer/Rectifier Unit — Provides the low voltage/high current

The water softener, salt saturator, transformer/rectifier, and storage tank

The hypochlorite generation system is under the control of a dedicated

Generation is primarily determined by the level switches at the storage

it operates primarily during off-peak electricity hours to keep generation

1.2 Water Softener

The softener consists of two cylinders incorporating ultra-fine particle