0% found this document useful (0 votes)
56 views29 pages

Controlpro Manual en

Uploaded by

Anderson Moreira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
56 views29 pages

Controlpro Manual en

Uploaded by

Anderson Moreira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 29

Controlpro

User manual
EN V 2.3.2
Legal notes

Product Serial number

Controlpro, Dual-Core, 4 GB RAM, 250 GB SSD From PNX11-20001-000405 ascending

Controlpro, Quad-Core, 8 GB RAM, 250 GB SSD From PNX11-20002-000286 ascending

Controlpro, Quad-Core, 16 GB RAM, 500 GB SSD From PNX11-20003-000286 ascending

This user manual contains the most important information for


operating the Controlpro in a safe manner. Please study this
manual carefully before working with the device. This applies to
all persons who come into contact with the device.

The product names mentioned in this document may be brands or registered trademarks
of their respective owners. These are not explicitly labeled with “™” or “®”.

© PEAKnx GmbH
Otto-Röhm-Strasse 69
64293 Darmstadt
Germany

www.peaknx.com
[email protected]
Document version: 2.3.2
Date: 12.04.24
Warning symbols and signal words used in this manual

Warning symbols and signal words used in this manual

Warning Obey warning to avoid death or serious injury

Caution Obey instructions to avoid personal injury or damage to property

 Note Instructions and facts to be followed

 Tip Additional, useful hints

Important safety instructions, please read before installation!

Warning

The device can carry dangerous voltages if improperly installed!


▪ Installation and commissioning may only be carried out by specially trained personnel
(qualified electricians).

Caution

Avoid damage to the panel!


▪ Only use the panel in perfect condition, as well as in accordance with its intended use,
in a way that is safe and aware of the hazards and in compliance with this manual!
▪ Do not make any changes, attachments or conversions to the device without the
manufacturer’s permission!
▪ In particular, have faults that could impair safety immediately eliminated!
▪ To minimise the risk of burn-in and excessive heat generation, the screen of this device
is configured to switch off automatically after a certain period of inactivity. This not only
protects the screen, but also extends the overall lifespan of the device. Please note
that this function helps to save energy and optimise the performance of the device. We
recommend that you do not switch off the proximity sensor completely under Panel
Settings (Control Micro / Control 12) and that you do not deactivate the screen switch-off
function.
Table of Contents

Table of Contents
Warning symbols and signal words used in this manual 3
Important safety instructions, please read before installation! 3
1 Target audience 6
2 Intended use 6
3 Product description 7
3.1 Software 7
3.1.1 Operating system 7
3.1.2 Operation with the PEAKnx Software YOUVI 7
3.1.3 Operation with third-party software 7
3.2 Variant overview 8
3.3 Components 9
3.4 Touch panel, front view 10
3.5 Touch panel, rear view 11
3.6 Touch panel, top view 12
3.7 Product features 12
3.8 Notes on the panel’s ports 13
3.8.1 KNX terminal 13
3.8.2 Ethernet port 13
3.8.3 Power supply 13
3.8.4 Connections for external mouse and keyboard 13
3.9 Controls 14
3.9.1 Graphical user interface 14
4 Scope of delivery 14
5 Important safety and handling information 15
6 Installation and start-up 16
6.1 Information for electricians 16
6.2 Installing the flush-mounted box 16
6.2.1 Installing the flush mounted box in brickwork 16
6.2.2 Installing the flush mounted box in a cavity wall 17
6.3 Connecting the power supply 17
6.3.1 Prepare the voltage source for the DIN rail 17
6.3.2 Preparing the voltage source for the flush-mounted box  17
6.4 Connecting and fastening the panel 19
7 Initial commissioning and operation 19
7.1 Switching the Controlpro on and off 20
7.2 Activate keyboard input 20
7.3 Setting up the visualization 21
8 Maintenance 21
8.1 Cleaning the touchscreen 21
9 Troubleshooting 22
9.1 Windows has unrecoverable problems 22
9.2 Touchscreen stops responding 22
Table of Contents

9.2.1 Turning the panel off and back on 22


9.2.2 Disconnecting the panel from the power supply 22
9.3 Controlpro touch operation works worse or only partially  23
9.4 Technical support 24
10 Technical data 24
Subject to change without notice 27
Conformity 27
Disposal notes 27
1 Target audience

1 Target audience
These instructions are intended to explain basic aspects of the installation, commissioning,
operation and maintenance of the Controlpro. Depending on the use phase, this manual is
aimed at other target groups:

Commissioning
▪ Installation and commissioning may only be carried out by qualified electricians and system
integrators. Basic knowledge of electrical and KNX installation is assumed.

Operation
▪ The operation of the commissioned panel is explained for unskilled users.

Repair
▪ Under no circumstances carry out repairs to the unit yourself! If damage should occur to the
device, please contact our technical support immediately,
see chapter 9.4.

2 Intended use
Depending on the software used, the Controlpro serves as control unit for the entire KNX
installation across rooms. It thus also serves as a status display. The device must be operated
within the scope of the technical data and instructions given in this manual. Keep the device
away from moisture, dirt and dust to prevent damage to the device.
The following applications belong to the intended use:
▪ Use as an operating panel (input via touch) for KNX-controlled devices
▪ Intercom station for compatible door stations
− A list of all compatible door stations can be found in our FAQ:
www.peaknx.com/FAQ under the topic “compatibility”.
▪ Indoor operation, note the ambient conditions, see chapter 10

The following applications are not part of the intended use:


▪ Operation in systems requiring special monitoring, in safety-relevant areas or in hazardous
areas
▪ Operation under ambient conditions that do not comply with the specifications regarding
temperature and air humidity. These include
− Outdoor operation
− Operation under direct sunlight
− Operation in environments with high dust and dirt exposure
− Operation in environments with high vibration exposure
▪ Operation in a moving environment (e.g. mobile homes)
▪ Operation in vessels
▪ Operation of the device by small children
▪ Use with an unrelated bus coupler

6
3 Product description

▪ Unauthorized repairs or changes to the device

3 Product description
The Controlpro (short: panel) is a high-quality panel computer for wall mounting. It serves
as a display and control unit for the components and installations controlled via KNX.

3.1 Software
The panel can be operated both with the supplied YOUVI software and with other
Windows-compatible software.

3.1.1 Operating system


The operating system used is Microsoft Windows 10 IoT Enterprise LTSC. All components requi-
red for the unit to function have been pre-installed. To activate functions such as write protec-
tion, the preinstalled Tectool can be used. Further instructions and drivers can be downloaded
from www.peaknx.com in the download area. Other programs for the visualization of building
information and for building control can be installed later. PEAKnx provides no service and no
warranty for software products from other companies as well as in case of OS driver updates.

3.1.2 Operation with the PEAKnx Software YOUVI


The YOUVI Basic visualization software included in the scope of delivery is used to control
KNX devices such as sockets, switches, lights, dimmers, RGB lights, heaters, blinds and
shutters. Thanks to the IP router included in the software package, the panel can run YOUVI’s
visualization without an external server or additional bus coupler. Only the connection to the
IP network and the KNX bus (via the integrated KNX connection on the panel) is necessary. In
addition to visualization and IP router, a bus monitor is also included in the scope of delivery,
which can record and filter the KNX traffic.
In addition to the basic functions for controlling KNX devices, YOUVI can be extended via
modules for IP camera connection, creation of logics, control via app on the road or voice
control. All current modules are available in the shop at
www.peaknx.com > Shop > Software > YOUVI.

 Note: For the YOUVI installation, please pay special attention to the YOUVI quick reference
guide and the information on KNX project preparation to enable the automatic reading of the
project. This quick reference guide is included in the delivery.

For more information about YOUVI, see the YOUVI Help which you can access in YOUVI under
the “?”-icon. Here you will also find the current range of functions of the software under:
Visualization > Scope of functions.

3.1.3 Operation with third-party software


The Windows 10 LTSC operating system pre-installed on the panel allows the use of other
Windows-based software for e.g. visualizations and door intercoms. Depending on the software

7
3 Product description

used, the functional scope of the panel can be expanded considerably. A list of compatible
software can be found in the FAQs:
www.peaknx.com/en/FAQ, topic “compatibility”.

 Note: PEAKnx does not guarantee the function of third-party software on the panel.

Further instructions for setting up the panel can be found in the download area:
www.peaknx.com/downloads#controlpro

3.2 Variant overview

Product Processor Working memory Hard drive Article number

DC-4-250 Dual-Core 4 GB RAM 250 GB SSD PNX11-20001

QC-8-250 Quad-Core 8 GB RAM 250 GB SSD PNX11-20002

QC-16-500 Quad-Core 16 GB RAM 500 GB SSD PNX11-20003

8
3 Product description

3.3 Components

Position Description Dimensions (H x W x D)

A1 Flush-mounted box 312 x 528 x 65 mm

A2 Panel with touchscreen 320 x 536 x 52,5 mm

A3 Glass cover 330 x 560 x 1.8 mm

9
3 Product description

3.4 Touch panel, front view

Position Description

B1 4 x screw holes for fixing the panel

B2 4 x intake for glass cover

B3 Microphone

B4 Camera

B5 Ventilation openings

B6 Touchscreen

B7 2 x USB 2.0, status LED

B8 Cooling element

B9 On/Off button

10
3 Product description

3.5 Touch panel, rear view

Position Description

C1 Power supply 19 - 24 V DC

C2 KNX terminal
(KNX WAGO 243 211, conductor diameter: 0.6 - 0.8 mm)

11
3 Product description

3.6 Touch panel, top view

Position Description

D1 HDMI V1.4

D2 DisplayPort V 1.2

D3 2 x USB 2.0*

D4 2 x USB 3.1 Gen1*

D5 PS/2 Keyboard

D6 LAN (1 GBit)

D7 Audio Line-In, Line-Out

* Directly connected USB devices can heat up excessively over longer periods of time due to
the convection heat generated. Use an extension cable to the USB port, especially for power-
intensive devices, to prevent the USB-device from overheating.

3.7 Product features


▪ LED backlit color TFT display 1920 × 1080 pixels, 16.7 million colors
▪ Touchscreen, multi-touch, projected capacitive (PCAP) touch technology
▪ Integrated speakers and microphone
▪ Integrated camera, with sliding shutter
▪ Fieldbus connection for KNX
▪ Gigabit Ethernet port
▪ Operating system: Windows 10 IoT Enterprise LTSC
▪ Fanless
▪ Power supply: 19 - 24 V DC

12
3 Product description

▪ Maximum power consumption under full load: 55 W


▪ Power consumption in standby: 1.5 W
▪ Operating temperature range: 0 to 35 °C
▪ Flush-mounted wall installation, in an upright position and in landscape orientation
(with display parallel to the wall)
▪ Protection class IP20

3.8 Notes on the panel’s ports

3.8.1 KNX terminal


A terminal of the following specification is used for the KNX connection:
KNX WAGO 243 211, conductor diameter: 0.6 - 0.8 mm.

 Note: The KNX fieldbus can only be used with PEAKnx software.

3.8.2 Ethernet port

 Note: Make sure to install the correct cabling standard to fully use the 1 GB LAN (at least Cat 5).

3.8.3 Power supply


The plug-in terminal for the voltage supply has a usable wire cross-section of 0.75 to 1.31 mm².

 Note: The supply voltage of the device may only lie within the specified range of 19 to
24 V DC! Higher voltages will damage the device.

3.8.4 Connections for external media, mouse and keyboard


To connect additional controls to the panel, such as an external mouse or keyboard, there are
four rear panel USB ports and a PS/2-port available. There are two additional USB ports on the
panel front under the glass cover, for example to use a USB adapter for a wireless keyboard
and mouse, or to transfer data onto the panel.

Caution

Avoid overheating of plugged-in USB devices!


Directly connected USB devices can heat up excessively over longer periods of time due to
the convection heat generated.
▪ Use an extension cable to the USB port, especially for power-intensive devices.

13
4 Scope of delivery

3.9 Controls

Caution

Avoid danger of injury from falling parts!


▪ Ensure that small children do not have access to the magnetically adhering front glass
and can’t accidentally loosen it.

3.9.1 Graphical user interface


Touch the panel to operate. A brief touch of the panel is interpreted as a mouse click. A right
mouse click is obtained by a prolonged touch (approx. 3 seconds). Text may be entered using
the Windows on-screen keyboard.

Caution

Avoid damage to front glass and display!


▪ Do not use the touch screen with sharp or pointed objects.

4 Scope of delivery
▪ Controlpro panel incl. YOUVI software package Basic (on USB flash drive)
▪ Controlpro user manual (this document)
▪ YOUVI quick reference guide
▪ Cleaning cloths for the touchscreen

Optionally included in scope of delivery:


▪ Controlpro power supply unit for the flush-mounted box or switch cabinet
▪ Flush-mounted box
▪ Controlpro 230 V connection set
▪ Glass cover
▪ Recovery USB flash drive

Necessary components for the installation of the panel:


▪ Flush-mounted box (PNX11-20006)
▪ Power supply unit 19 - 24 V DC for DIN rail (PNX11-20011)
or
▪ Power supply 19 - 24 V DC for the flush-mounted box (PNX11-20008)

14
5 Important safety and handling information

5 Important safety and handling information

Warning

The Controlpro may only be installed and commissioned by qualified electricians!

Warning

Observe the national regulations applicable in your country regarding installation,


functional testing, repair and maintenance of electrical products!
▪ Observe the „Five Safety Rules“ (DIN VDE 0105, EN 50110) and apply them correctly:
− Disconnect mains
− Prevent reconnection
− Test for absence of harmful voltages
− Ground and short circuit
− Cover or close off nearby live parts
▪ Before installation, make sure that all connecting cables of the device are undamaged.

Caution

Avoid injuries!
▪ The device contains backup batteries. Do not heat them! A burst of the Batteries can
cause serious injury.

Caution

Avoid damage to the panel!


▪ The panel may only be installed upright and in landscape orientation to ensure the
ventilation of the computer by convection.
▪ The supply voltage of the device may only lie within the specified range of 19 to 24 V DC!
Higher voltages will damage the device.

15
6 Installation and start-up

6 Installation and start-up


The panel can only be inserted into a wall cut-out in masonry or cavity walls. Use the Controlpro
flush-mounted box (PNX11-20006) or a compatible one, e.g. that of the Gira Control 19.

6.1 Information for electricians

 Note: We recommend fusing the panel separately, because in rare cases it must be
completely disconnected from the power supply, see section 9.2.2 Disconnecting the panel
from the power supply.

6.2 Installing the flush-mounted box

 Tip:Choose the installation height of the panel according to the height of the primary user
so that the top edge of the panel is at his/her eye level. If there are multiple users of different
heights a compromise must be found. A slightly lower screen prevents fatigue of the arms
during operation.

 Tip:If you have ordered a PEAKnx flush-mounted box for the panel you can use the supplied
template to mark the recess.

6.2.1 Installing the flush mounted box in brickwork

▪ Mark a 312 x 528 mm recess on the wall, but leave bevels in the corners.
These will later be used for fixing the flush-mounted box.
▪ Make the recess in the wall with a depth of 65 mm.

▪ Insert the flush-mounted box and lead the Ethernet, KNX and power
supply cables through the holes in the flush-mounted box.
▪ Screw the flush-mounted box to the wall.

 Tip: During the filling of the edges, the template can be used as a splash guard.

16
6 Installation and start-up

6.2.2 Installing the flush mounted box in a cavity wall

▪ Mark a recess of 312 x 528 mm on the wall.


▪ Make the recess in the wall according to your mark.

▪ Install separate mounting corners flush with the wall.

▪ Insert the flush-mounted box and lead the Ethernet, KNX and power
supply cables through the holes in the flush-mounted box.
▪ Fasten the flush-mounted box with four screws in the
corners.

6.3 Connecting the power supply

Warning

Avoid electric shock when touching live parts!


▪ Disconnect all associated circuit breakers before working on the device.
▪ Cover live parts in the surroundings.

6.3.1 Prepare the voltage source for the DIN rail


▪ Use a power source of the following specification:
− 19 - 24 V DC for the control cabinet, Item number: PNX11-20011
− Max. current: during operation: 3 A, during the PC boot process: 3.5 A (at 19 V)
▪ Disconnect the pluggable screw terminal (C1) from the Controlpro.
▪ Connect the cable cores of the power supply unit to it.

6.3.2 Preparing the voltage source for the flush-mounted box


Particularly, when replacing a foreign device with the Controlpro, a power supply is often
already present in the flush-mounted box. This means that mains voltage and low voltage are in
the same housing and if connected incorrectly, even parts that normally only carry low voltage
unintentionally carry mains voltage.

17
6 Installation and start-up

Warning

Avoid touching dangerous voltages in the event of a fault!


▪ Route cables so that low voltage wires are dependably protected against mains voltage.

▪ Screw the power supply unit to the flush-


mounted box at its mounting feet using the two
supplied self-tapping screws.
▪ Mounting position: at central height approx. 2 cm
from the left side of the flush-mounted box.

▪ Connect the 230 V side of the power supply to


the right side of the terminals on the Controlpro
flush-mounted box as shown in the picture.
▪ Connect the mains cable to the left side of the
luster terminal as shown in the picture.

Depending on the flush-mounted box, some- times


it is necessary to extend the 230 V side of the
power supply. Use the Controlpro 230 V
connection set, also available in the shop.
▪ Prepare the connectors as shown in the picture.
▪ Make sure to connect the earthing at all points!

Now connect the 19 - 24 V side.


▪ Disconnect the pluggable screw terminal (C1) from
the Controlpro.
▪ Connect it to the cable wires of the power supply
unit.
▪ Pay attention to the correct polarity, as indicated
on the power supply unit: red (+) and black (-).

18
7 Initial commissioning and operation

6.4 Connecting and fastening the panel

Preparation
▪ Place the screws (M5x16) included in the scope of delivery within reach for fixing the panel
within the flush-mounted box.
▪ For further notes on the panel’s ports, please read section 3.8 Notes on the panel’s ports.

Connection of the panel


▪ Push the prepared 19-24 V connector terminals back into the appropriate connectors
in the panel (C1).
▪ Connect the Ethernet cable to the panel (D6).
▪ Plug the KNX cable with the colors red (+) and black (-) into the KNX-terminal (C2).

Mounting the panel


▪ Fasten the panel with the enclosed countersunk screws (M5x16, 4 pieces) in the
flush-mounted box.

 Note: Make sure that the ventilation openings (B5) are not partially or fully covered to
ensure convection ventilation of the computer in the panel.

Attaching the glass cover


▪ Place the glass cover with the magnetic holders into the four intakes provided and continue
until the glass rests against all four corners of the touchscreen.
▪ Ensure that the opening for the camera is positioned on the upper screen.

7 Initial commissioning and operation

Caution

Avoid damage to the panel due to early commissioning!


▪ Note the climatic conditions at the installation site!
▪ Before switching on the mounted device, the device must have adapted to the climatic
conditions at the installation site.
▪ Temperature and humidity differences can cause damage to the unit.

19
7 Initial commissioning and operation

 Tip: After commissioning and setting up the panel, we recommend that you create a backup
using the optionally available recovery USB flash drive from PEAKnx. Further instructions can
be found in the corresponding Quick Start Guide.

Caution

Avoid damage to the panel!


▪ The touch-sensitive surface can easily be damaged! Use only your fingers or a touchpen
to operate the panel. Do not use sharp or pointed objects.

7.1 Switching the Controlpro on and off

 Note: In delivery state, the panel automatically logs on with the user name
Controlpro without a password. After the login, additional users can be added at any time or
further settings may be changed in the Windows Settings.

The On/Off button (B9) is accessible when the glass cover is removed.

Switching the panel on


▪ Briefly press the On/Off button.
The operating system will boot.
When the panel is on, the blue LEDs on the front USB ports light up.

Switching the panel off


▪ Briefly press the On/Off button to switch off.
Or:
▪ Tap the Windows logo on the Windows Start screen and select the On/Off icon and
select the option “Shut down”.
The operating system will shut down and switch off the computer.

 Note: In normal operating conditions, it is not necessary to switch off the Controlpro.

7.2 Activate keyboard input


To automatically display the keyboard when tapping on a text input field, do the following:
▪ Swipe into the screen from the right and select “All settings”.
▪ Select “Devices” > “Typing”.
▪ Under “Touch keyboard”, check the last item: “Show the touch keyboard when not in tablet
mode and there’s no keyboard attached.”

20
8 Maintenance

To display the keyboard icon in the taskbar:


▪ Right-click on the taskbar and select “Show touch keyboard button”.

7.3 Setting up the visualization


After commissioning, set up the visualization as described in the enclosed quick reference
guide. It is assumed that all KNX actuators have already been parameterised via the ETS. The
corresponding KNX project then only needs to be uploaded to YOUVI Configuration > Projects.
At the end of the process make a backup of your configured visualization.

 Note: For YOUVI installation, please pay special attention to the YOUVI quick reference
guide and the information about KNX project preparation to enable the automatic import of the
project. The quick reference guide is part of the delivery.

8 Maintenance

8.1 Cleaning the touchscreen


By cleaning the touch surface, you prevent fingerprints or dust from impairing the touch function.

Caution

Avoid damage to the glass cover and display!


▪ Do not use harsh detergents, scouring agent, acids or organic solvents. Do not use any
sharp objects for cleaning.
▪ Do not let any moisture get into the unit. Do not spray cleaning agents directly onto the
surface of the touchscreen.

Removing the glass cover


▪ Use both hands to take the glass cover on both sides.
▪ Carefully pull the glass cover away from the panel towards yourself.

Switching on the cleaning mode


If you are using the supplied YOUVI visualization, switch on the cleaning mode for cleaning.
Therefore, proceed as follows:
▪ In the YOUVI visualization, switch to the settings.
▪ Tap on “Activate cleaning mode” in the upper left corner.
Now, active elements are deactivated for 20 seconds to prevent you from accidentally
changing device values during cleaning.

Cleaning the touchscreen


▪ Clean the touchscreen with glass cleaner or one of the supplied cleaning cloths.

21
9 Troubleshooting

Attaching the glass cover


▪ Place the glass cover with the magnetic mounts over the four intakes provided and lower the
glass until it lies flat on all four corners of the touchscreen.
▪ Ensure that the hole for the camera is positioned on the upper screen.

9 Troubleshooting
If you have problems with the Controlpro, please do not carry out repairs yourself, but contact
your distributor. Opening the unit invalidates the warranty.

9.1 Windows has unrecoverable problems


If the Windows user interface shows unrecoverable problems, the operating system can be
reset to factory settings.

 Note: The restore process may take up to 30 minutes. During this time, the panel cannot be
used for building control.

Each Controlpro is provided with an image for restoring the software to the state of delivery. To
restore the panel to this state, proceed as follows:

 Note: It is recommended to create a backup of the YOUVI server in YOUVI Configuration >
General > General and a backup in the YOUVI Visualization > YOUVI Settings before restoring
the factory state. Save the backup to a separate storage medium.

▪ Type “Recovery” in the Windows search box and select the “Recovery Options”.
▪ Select the button “Restart Now” under “Advanced Startup”.
▪ You will be redirected to the Advanced Startup menu.
▪ Select “Troubleshoot”.
▪ Select “PEAKnx Factory Reset”.
▪ The factory state will be restored.

9.2 Touchscreen stops responding


If the Controlpro no longer reacts to input on the touchscreen (which may occur in rare cases
following Windows updates), try to reboot the panel. If the problem persists, disconnect the
panel from the power supply, as shown in 9.2.2 Disconnecting the panel from the power supply
and restart it. If this does not solve the problem, please contact our technical support; chapter
9.4 Technical support.

9.2.1 Turning the panel off and back on


If the operating system cannot be shut down, the panel must be turned off manually and a
reboot must be forced.

 Note: Any data that has not been saved might be lost when forcing a restart.

22
9 Troubleshooting

Forced restart
▪ Press and hold the On/Off button (B9) for more than 5 seconds.
The panel switches off.
▪ Switch on the panel by pressing the On/Off button (B9) again.

9.2.2 Disconnecting the panel from the power supply


If the problem cannot be solved by restarting the panel, you must disconnect the panel from the
power supply.
▪ Disconnect the circuit breaker of the panel in the building’s control cabinet for at least one
minute.

9.3 Controlpro touch operation works worse or only partially


If the touch screen of the Controlpro does not work as usual anymore, for example after an
update a new calibration of the touch screen can help.

 Note: Do not perform the screen calibration with the Windows Touch Calibration. If this has
already been performed, open the Windows Control Panel and there the “Tablet PC Settings”.
Here you can reset the calibration.

Proceed as follows for professional calibration:


▪ Open the folder C:\Peaknx\eGalaxWorks... and double-click on the “eGalaxUpdate2” file to
load the appropriate firmware for the touch controller onto the panel.
The following window opens:

23
10 Technical data

▪ Click on “Load Image” and select the 3189UR file “PCAP...” from the same folder.
▪ Click on “Go!”.
A rough pre-calibration starts. After this, close the window.
▪ Then open the application file “eGalaxCalibration“ from the same folder for complete
calibration.
4 points appear on the screen, which must be touched on the touchscreen. After that, the
calibration is finished.

9.4 Technical support


If you experience problems with your Controlpro, please contact our PEAKnx
Support Team:
▪ Mail: [email protected]
▪ Create a support ticket: support.peaknx.com/?lang=en_US
▪ Phone: +49-6151-279 1825

10 Technical data

Supply

Power supply 19 - 24 V DC, Max. current: during operation: 3 A, during the


PC boot process: 3.5 A (at 19 V)

Connection terminal 0.75 to 1.31 mm² usable wire cross-section

KNX bus voltage 19 V to 33 V

Fuse 4 A, slow blow

Power consumption Operation: 44 W


Operation (Full load): 55 W
Standby: 1.5 W

Computer system

Processor Intel Dual-Core or Intel Quad-Core


fanless cooling by convection

Memory (RAM) 4, 8 or 16 GB

Hard drive SSD with 250 or 500 GB

Operating system Windows 10 IoT Enterprise 2021 LTSC

24
10 Technical data

Display

Type TFT color screen

Backlighting LED

Color resolution 16.7 million colors

Size (diagonal) 46.9 cm (18.5 inch)

Aspect ratio 16:9

Resolution 1920 x 1080 pixels

Maximum brightness 350 cd/m²

Viewing angle
horizontal (left/right) 89°/89°
vertical (up/down) 89°/89°

Touch technology Projected-capacitive touch (PCAP), Multi-touch

Peripherials

Speakers Broadband, stereo

Microphone Room characteristic

Webcam 5 Megapixels

Dimensions

Computer with panel 536 x 320 x 52,5 mm

Glass cover 560 x 330 x 1.8 mm

Weight

Computer with panel wit- 4610 g


hout glass cover

Glass cover 860 g

Ports

USB 2 x USB 2.0 (Front port), 2 x USB 2.0, 2 x USB 3.1, Gen1

Ethernet Gigabit Ethernet

25
10 Technical data

Ports

External screen HDMI V1.4, DisplayPort V1.2

Keyboard PS/2

Fieldbus KNX

Audio Line out, Line in, jack, 3.5 mm

Environment

Ambient temperature Operation: 0 to 35 °C


Storage, transport: -20 to 60 °C

Relative humidity Operation: 10 to 85 % r.H., no condensation


Storage, transport: 10 to 85 % r.H., no condensation, from
+40°C: 10 to 39 % r. H., no condensation

Protection class (DIN EN IP20


60529)

26
Subject to change without notice

Subject to change without notice


Content changes in this documentation, which serve the technical progress, are made without
prior notice. This documentation has been prepared with great care and will be revised at
regular intervals. Nevertheless, we cannot guarantee complete accuracy. All known errors are
eliminated in new editions. For any indication of errors in this documentation, we are always
grateful.

Conformity
Conformity is confirmed by the attached CE label. The standards taken into account are inclu-
ded in the Declaration of conformity. The complete declaration of conformity is shown on page
28.

Disposal notes
Do not dispose the old device in the household waste!
Observe the EU Directive 2012/19/EU on environmentally friendly disposal of used electrical/
electronic equipment.

Waste of electrical and electronic equipment can


▪ contain hazardous substances that are harmful to health and the environment.
▪ contain valuable substances that are to be reused.

Therefore, do not dispose of with household waste.

Waste of electrical and electronic equipment can be returned to public collection points.

27
Declaration of conformity

EU Declaration of Conformity w

This declaration applies to the following product:

Product name: Controlpro


Item number(s): PNX11-20001, PNX11-20002, PNX11-20003
Manufacturer: PEAKnx GmbH
Otto-Roehm-Strasse 69
64293 Darmstadt
Germany

We declare under our sole responsibility that the mentioned product is in conformity with
the following directives and the affiliated harmonized standards:

EU Directive 2011/65/EU (RoHS 2) + 2015/863/EU (amended list of restricted substances)


DIN EN IEC 63000 VDE 0042-12:2019-05
Technical documentation for the assessment of electrical and electronic products with respect to
the restriction of hazardous substances (IEC 63000:2016); German version EN IEC 63000:2018

EU Directive 2014/30/EU (Electromagnetic Compatibility)


• DIN EN 55032 VDE 0878-32:2022-08
• DIN EN IEC 63044-5-1:2020-04; VDE 0849-44-51:2020-04
• DIN EN IEC 63044-5-2:2020-04; VDE 0849-44-52:2020-04
• DIN EN IEC 63044-5-3:2020-04; VDE 0849-44-53:2020-04
• DIN EN 55011 VDE 0875-11:2022-05

PEAKnx GmbH, Executive Management

Lorenz Rohrmann, 2022-11-22

28
www.peaknx.com

You might also like