LM-8000

Multi-Function
Environmental
Meter

Instruction
Manual
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Table of Contents
Introduction................................................................................................. 2
Product Quality............................................................................................ 3
Safety.......................................................................................................... 3
Features....................................................................................................... 3
Specifications...........................................................................................4-5
Included....................................................................................................... 5
Instrument Description................................................................................ 6
Operating Instructions............................................................................7-10
Power ON/OFF....................................................................................... 7
Selecting Measurement Modes.............................................................. 7
Air Velocity/Temperature Measurement.................................................. 7
Thermocouple Temperature Measurement............................................. 8
Relative Humidity and Ambient Air Temperature
Measurements........................................................................................ 8
Light Measurements............................................................................... 8
Zero Adjustment..................................................................................... 9
Data Hold................................................................................................ 9
Recording Maximum and Minimum Readings........................................ 9
Auto Power Off..................................................................................... 10
Battery Replacement................................................................................. 10
Accessories and Replacement Parts........................................................ 10
Product Care............................................................................................. 10
Product Warranty...................................................................................... 11
Product Disposal and Recycling............................................................... 11
Product Support........................................................................................ 11

REED Instruments 2
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Introduction
Thank you for purchasing your REED LM-8000 Multi-Function
Environmental Meter. Please read the following instructions carefully
before using your instrument. By following the steps outlined in this
manual your meter will provide years of reliable service.

Product Quality
This product has been manufactured in an ISO9001 facility and has been
calibrated during the manufacturing process to meet the stated product
specifications. If a certificate of calibration is required please contact the
nearest authorized REED distributor or authorized Service Center. Please
note an additional fee for this service will apply.

Safety
Never attempt to repair or modify your instrument. Dismantling your
product, other than for the purpose of replacing batteries, may cause
damage that will not be covered under the manufacturer's warranty.
Servicing should only be provided by an authorized service center.

Features
• Measures air velocity/temperature, ambient temperature, relative
humidity, contact temperature and light
• Easy to operate, designed for one hand operation
• Air velocity is measured in m/s, ft/min, km/h, mph or knots
• Light levels are measured in foot-candles or lux
• Temperature is measured in °C or °F
• Data Hold and Max/Min functions
• Zero adjustment button (light meter)
• Low battery indicator and auto shut off

REED Instruments 3
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Specifications
Air Velocity
Measuring Ranges: 0.4 to 30.0m/s
1.4 to 108.0km/h
0.9 to 67.0 mph
80 to 5910 fpm
0.8 to 58.3 knots
Accuracy: <20m/s: ±3% FS
≥20m/s: ±4% FS
Resolution: 0.1m/s, km/h, mph, knot
1 fpm
Temperature
Measuring Ranges: Air Temperature: 32 to 122.0°F (0 to 50°C)
Contact Temperature (Type K):
-148 to 2372°F (-100 to 1300°C)
Accuracy: Air Temperature: ±1.2°C (2.5°F)
Contact Temperature: ±(1% rdg +2°F(1°C))
Resolution: 0.1°F/°C
Humidity
Measuring Range: 10 to 95%RH
Accuracy: ≥70%RH: ±(4% rdg + 1.2%RH)
<70%RH: ±4%RH
Resolution: 0.1%RH
Light
Measuring Range: 0 to 20,000 Lux (0 to 1860 Ft-cd)
Accuracy: ±(5% rdg ± 8 dgt)
Resolution: 0 to 2200 Lux (0 to 204.0 Ft-cd):
1 Lux / 0.1 Ft-cd
1800 to 20,000 Lux (170 to 1860 Ft-cd):
10 Lux / 1 Ft-cd

continued...

REED Instruments 4
1-877-849-2127 | [email protected] | www.reedinstruments.com
 General Specifications
Response Time: 1 second
Display: LCD
Data Hold: Yes
Min: Yes
Max: Yes
Zero Adjustment: Yes (for Light)
Auto Shut-off: Yes (after 10 minutes)
Low Battery Indicator: Yes
Power Supply: 9V Battery
Product Certifications: CE
Operating Temperature: 32 to 122°F (0 to 50°C)
Storage Temperature: 14 to 140°F (-10 to 60°C)
Operating Humidity Range: 10 to 85%
Dimensions: 6.1 x 2.4 x 1.3" (156 x 60 x 33mm)
Weight: 8.8oz (160g)

Included
• Wrist Strap
• Battery

REED Instruments 5
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Instrument Description

8
2
LM-8000
9
3
10

4 11

5 12

13

1. Air Flow Sensor 8. Relative Humidity Sensor

2. Thermocouple Input Socket 9. Battery Cover
3. LCD display 10. Hold Button
4. POWER Button 11. Max/Min Button
5. Unit/Zero Button 12. Function Button
6. Light Sensor 13. °C/°F Button &
7. Wristlet Lux/Ft-cd Button

REED Instruments 6
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Operating Instructions
Power ON/OFF
Turn the instrument on or off by pressing the POWER button.

Selecting Measurement Modes

The LM-8000 offers 4 types of measurement modes:
• Air Velocity/Temperature
• Humidity/Temperature
• Type K Thermocouple Temperature
• Light Meter
1. When the meter is on, press the FUNCTION button to cycle
through the measurement modes. The display will flash "An" (for air
velocity/temperature measurements), "rH" (for humidity/
temperature measurements), "tP" (for type K thermocouple
temperature measurements), "LigHt" (for light measurements).
2. Release the FUNCTION button once the appropriate
measurement mode has been selected.

Air Velocity/Temperature Measurement

1. Select the "An" function (see Selecting Measurement Modes section
for details). In Air velocity mode, the display will show both Air
Velocity and Temperature simultaneously.
2. Press the UNIT button to cycle through the units of measurements
(fpm, m/s, km/h, mph and knots).
3. When selected, face the Air Flow Sensor to the source of wind.
Note: For the best results when using your instrument, make sure the
air stream and the sensor are aligned (±20 degrees maximum) and wait
approximately 3 seconds for the reading to stabilize.
4. When the readings are stable, note the measured value.

continued...

REED Instruments 7
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Thermocouple Temperature Measurement
1. Plug the optional Type K Thermocouple Probe into the thermocouple
input jack.
2. Select the "tP" function (see Selecting Measurement Modes section
for details). In this mode, the LCD display will only show the
thermocouple temperature.
3. Press the °C/°F button to select between °C and °F.
Note: If no thermocouple is connected, the meter will display "-----".
Relative Humidity and Ambient Air Temperature
Measurements
When the meter is introduced into a new environment, it will take a few
minutes to fully stabilize.
1. Select the "rH" function (see Selecting Measurement Modes section
for details). In "rH" mode, the display will show %RH and ambient air
Temperature simultaneously.
2. Press the °C/°F button to select between °C and °F.

Light Measurements
1. Select the "LIgHt" function (see Selecting Measurement Modes
section for details).
2. Press the Lux/Ft-cd button to select Lux or Foot-candle units of
measure.
3. Before taking measurements, a zero offset adjustment should be
performed (see Zero Adjustment section for details).
4. Hold the sensor toward the light source and note reading.

continued...

REED Instruments 8
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Zero Adjustment
• For best results you should zero the light sensor prior to first use in a
dark environment. To achieve this, place the light sensor end of the
meter under a desktop or flat surface to block any light. Press the
Unit/Zero button to perform the zero adjustment.
• The zero value can drift due to environment temperatures, battery
power, as well as various other reasons. It is recommended that the
zero be checked frequently using the above procedure.

Data Hold
1. While taking a measurement, press the HOLD button to freeze the
current readings on the display.
2. While in this mode a "HOLD" symbol will appear on the LCD.
3. Press the button again to resume normal operation.

Recording Maximum and Minimum Readings

1. Press the MAX/MIN button to enter recording mode as indicated by
"REC" on the LCD. The meter will now begin recording maximum
and minimum readings.
2. While in recording mode:
A) Press the MAX/MIN button once and the maximum value will
appear on the display as indicated by "REC MAX" and will
automatically update when a new maximum data value
is measured.
B) Press the MAX/MIN button again and the minimum value will
appear on the display as indicated by "REC MIN" and will
automatically update when a new minimum data value
is measured.
C) To exit recording mode and resume normal operation, press
and hold the MAX/MIN button for two seconds.
Note: When in recording mode the POWER button is disabled and the
meter cannot be turned off.

continued...

REED Instruments 9
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Auto Power Off
To preserve battery life, the meter is programmed to turn off after
10 minutes of inactivity.

Battery Replacement
When the low battery icon appears on the left corner of LCD display, you
will need to replace the batteries. Remove the battery cover using a
Phillips head screwdriver, insert a new 9V battery and secure the cover.

Accessories and Replacement Parts

• R2920 Surface Thermocouple Probe
• R2930 Right Angle Thermocouple Probe
• R2940 Air/Gas Thermocouple Probe
• R2950 Immersion Thermocouple Probe
• R2960 Needle Tip Thermocouple Probe
• TP-01 Beaded Thermocouple
• CA-52A Soft Carrying Case
Don't see your part listed here? For a complete list of all accessories and
replacement parts visit your product page on www.reedinstruments.com.

Product Care
To keep your instrument in good working order we recommend the following:
• Store your product in a clean, dry place.
• Change the battery as needed.
• If your instrument isn't being used for a period of one month or longer
please remove the battery.
• Clean your product and accessories with biodegradable cleaner. Do not
spray the cleaner directly on the instrument. Use on external parts only.

REED Instruments 10
1-877-849-2127 | [email protected] | www.reedinstruments.com
 Product Warranty
REED Instruments guarantees this instrument to be free of defects in
material or workmanship for a period of one (1) year from date of shipment.
During the warranty period, REED Instruments will repair or replace, at no
charge, products or parts of a product that proves to be defective because
of improper material or workmanship, under normal use and maintenance.
REED Instruments total liability is limited to repair or replacement of the
product. REED Instruments shall not be liable for damages to goods,
property, or persons due to improper use or through attempts to utilize the
instrument under conditions which exceed the designed capabilities. In
order to begin the warranty service process, please contact us by phone at
1-877-849-2127 or by email at [email protected] to discuss the
claim and determine the appropriate steps to process the warranty.

Product Disposal and Recycling

Please follow local laws and regulations when disposing or recycling your
instrument. Your product contains electronic components and must be
disposed of separately from standard waste products.

Product Support
If you have any questions on your product, please contact your authorized
REED distributor or REED Instruments Customer Service by phone at
1-877-849-2127 or by email at [email protected].

Please visit www.REEDInstruments.com for the most

up-to-date manuals, datasheets, product guides and software.

Product specifications subject to change without notice.

All rights reserved. Any unauthorized copying or reproduction of
this manual is strictly prohibited without prior written permission
from REED Instruments.

REED Instruments 11
1-877-849-2127 | [email protected] | www.reedinstruments.com
 TEST & MEASURE
WITH CONFIDENCE

CHECK OUT OUR LATEST PRODUCTS!

REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com