Model E
Thermostatic Valve
FEATURES Model EF
■ FLOW RATES OF 40 - 75 USGPM
AMOT Model E Thermostatic Valves are fully automatic, 3-
■ TAMPER-PROOF TEMPERATURE way fluid temperature controllers for diverting or mixing
SETTINGS OF 85°F TO 235°F applications. They are used to provide reliable control of
fluid temperatures in engine jacket water and lubricating oil
cooling systems. These valves are suitable for process
■ COMPLETELY SELF-CONTAINED control and industrial applications where fluids must be
mixed or diverted depending on their temperatures. They
may also be applied to cogeneration systems to control
■ COMBINATIONS AVAILABLE: temperatures in the heat recovery loop assuring proper
engine cooling and maximizing heat recovery.
CAST IRON, STEEL, & STAINLESS STEEL
1-1/4" & 1-1/2" PIPE SIZES Tamper-Proof
THREADED & FLANGED CONNECTIONS
As with other AMOT thermostatic valves, they utilize fully
enclosed, factory-set temperature element assemblies
■ HIGH PRESSURE VERSIONS UP TO which provide tamper-proof operation. To change a valve
setting, it is necessary to exchange the temperature ele-
CLASS 600# FLANGES ment assembly.
Versatile
APPLICATIONS Model E Valves can also be supplied with special Nickel
plated element assemblies and Neoprene seals to resist the
■ ENGINE & COMPRESSOR COOLING corrosive effects of ammonia-contaminated oil in refrigera-
tion compressor service.
SYSTEMS
Viton seals can be supplied for use in fluids which attack
Buna N such as phosphate ester and diester oils. With such
■ LUBE OIL SYSTEMS oils, nickel plated element assemblies should be requested
for protection of the bronze parts.
■ COGENERATION HEAT RECOVERY
High Resistance to Shock
LOOPS
AMOT thermostatic valves display excellent reliability even
under extreme shocks or vibration and can be qualified to
■ PROCESS CONTROL MIL-S-901 and MIL-V-19772.
Other AMOT Thermostatic Valves are available for water
■ TEMPERATURE MIXING OR DIVERTING flow rates of 9-2800 USGPM, see Form No. 913.
FORM 594
Operation Specifications
The valve is supplied with the temperature element assem- Internal Trim Materials .......................................... Bronze
bly factory-set to the nominal temperature setting. Tem- Standard Seal Material .......................................... Buna N
perature is sensed at Port A which remains open to Port B Max. Allowable Pressure Across Valve .. 20 psi (138 kPa)
(bypass) until the fluid temperature reaches a point 8-10°F Valve Pressure Rating - ELC ............. 355 psi (2448 kPa)
below the nominal setting. As the temperature continues to EFCF ........................ 155 psi (1069 kPa)
rise, the sliding valve moves to close off Port B and open EFSJ, EMSJ ............. 230 psi (1586 kPa)
Port C (connected to the cooler or heat exchanger.) Port B EFSH, EMSH ........... 655 psi (4516 kPa)
is fully closed 8-10°F above the nominal setting. The valve EFSK, EMSK ......... 1,000 psi (6895 kPa)
continually modulates the fluid flow to maintain the nominal Net Weight 1-1/2ELC ............................... 8 lbs (4 kg)
temperature. For optimum control, the system should be 1-1/4EF ............................... 20 lbs (9 kg)
sized so about 1/2 the total fluid flow is passing through the 1-1/2EF ............................... 20 lbs (9 kg)
cooler at full load. 1-1/2EFSH ........................ 30 lbs (14 kg)
1-1/2EFSK ......................... 36 lbs (16 kg)
For long life, AMOT Model E valves should not be exposed
to continuous temperatures exceeding 65°F above their
nominal temperature setting. For occasional short periods Selection
such as 1/2 hour, they can be exposed to temperatures of AMOT thermostatic valves are selected by the anticipated
90°F above their nominal temperature setting, but 250°F flow rate through the valve. Refer to Fig. 1. Pressure drop
maximum. across the valve is usually limited to approximately 2 to 7 psi
to maintain good temperature regulation.
Piping Diagrams
Versions available from USA factory. Contact factory for
Stainless Steel Versions.
Cast Iron Steel
1-1/4 EFCF 1-1/2 EFSJ
1-1/2 EFCF 1-1/2 EFSH
1-1/2 ELCT 1-1/2 EMSJ
1-1/2 EMSH
1-1/2 EFSK
1-1/2 EMSK
MODEL 1-1/2 EL MODEL 1-1/4 EF, 1-1/2 EF, 1-1/2 EM
Selection / Dimensions
Dia. of
Model Nominal No. of Holes Bolt
No. Size “W” “X” “Y” “Z” Holes “D” Circle
1-1/4EFCF 1-1/4 6-7/8 5/8 4-5/8 3-29/32 4 5/8 3-1/2
(32) (175) (16) (117) (99) (16) (89)
1-1/2EFCF 1-1/2 6-7/8 5/8 5 3-29/32 4 5/8 3-7/8
(40) (175) (16) (127) (99) (16) (98)
1-1/2EFSJ 1-1/2 7 9/16 5 3-31/32 4 5/8 3-7/8
1-1/2EMSJ (40) (178) (14) (127) (101) (16) (98)
1-1/2EFSH 1-1/2 8 13/16 6-1/8 4-3/4 4 7/8 4-1/2
1-1/2EMSH (40) (203) (21) (156) (121) (22) (114)
1-1/2EFSK 1-1/2 8-3/4 1-1/8 6-1/8 5-1/8 4 7/8 4-1/2
1-1/2EMSK (40) (222) (29) (156) (130) (22) (114)
Dimensions in inches, Millimeters in ( ).
How to Order
When ordering please specify the following:
1. Pipe size connection: 1-1/4" Flanged
1-1/2" Flanged
1-1/2" Threaded
See Table D & “Selection” section.
2. Indicate Model E.
3. Housing material: cast iron, steel, or stainless steel
(See “Selection” section).
4. Nominal temperature setting, see Table E.
5. Any of the following special features if required:
a) Nickel plated temperature element assembly.
b) Viton seals, Neoprene seals.
Fig. 1
c) Electroless Nickel Plated Temperature Element
Assembly Flow in U.S. Gallons Per Minute
d) Temperature Element Assembly Leak Hole, see Recommended Pressure Drop is 2 to 7 psi
Table G.
Model Code Table
1-1/2 EL C T 160 01 - ___ - ( )
Special Requirements, (MTO) Made-To-Order
Element Assembly Leak Hole, See Table G**
Element Assembly Type, See Table F
Temperature Setting, See Table E
TABLE A TABLE B TABLE C TABLE D*
Valve Size Valve Type Body Material Connections
Inches (mm) Code No. Material Code No. Material Code No. Type
1-1/4 (32) EL Threaded C Cast Iron FLANGED CONNECTIONS
Connections F ANSI B16.1 (125 lb Class) Flat Face Flange
1-1/2 (40) J ANSI B16.5 (150 lb Class) Raised Face Flange
EF Flanged S Steel
H ANSI B16.34 (300 lb Class) Raised Face Flange
Connections
K ANSI B16.37 (600 lb Class) Raised Face Flange
R Stainless
EM Manual Override Steel THREADED CONNECTIONS
T Threaded NPT to USAS B2.1
V Threaded BSP (Tr) and Japanese JIS
W Threaded to SAE J514h straight thrd O-ring seal
TABLE E TABLE E (Continued) TABLE F TABLE G**
Temperature Setting Temperature Setting Element Assembly Type Element Assembly
Code Nominal Temp Code Nominal Temp Code No. Type Leak Hole
No. °F (°C) No. °F (°C) 01 5435X Standard Code Size
No. Inches (mm)
085 085 (29) 170 170 (77) 02 5435P Plated w/Viton Seals
03 5435X w/Viton Seals none (standard)
095 095 (35) 175 175 (79)
100 100 (38) 180 180 (82) 04 5435P Plated w/Buna N Seals
A 1/8" (3.2)
05 5435X w/Neoprene Seals
110 110 (43) 190 190 (88)
06 5435K Electoless Nickel plated B 1/4" (6.4)
120 120 (49) 205 205 (96) w/ Neoprene Seals
130 130 (54) 237 237 (114) 07 9831X Manual Override C 3/16" (4.8)
140 140 (60) 10912X Manual Override, EMSK
08 9831P Plated Manual, Viton D 1/16" (1.6)
150 150 (66)
10912P Plated Manual, EMSK,
160 160 (71)
Viton Seals
NOTE: Letters or numbers in the MTO space, other than nothing, * Former model coding generally omitted Table D.
AI or AA, indicate the unit is built to special requirements and some ** Table G is to be omitted on any valve made in the USA not
of the other code numbers may not be valid. Check with the factory requiring a leak hole.
for full specification of such models.
Indicates Non-Standard, Special Charges May Apply
Service Parts Maintenance
Ref Part Properly applied and installed, AMOT Thermostatic Valves
No. No. Qty. Description require minimal maintenance.
For Model EL, EF (except EFSK, EMSK)
If necessary, temperature element assemblies may be
4 1919 1 O-ring, Buna N easily replaced. Remove Bolts (7) and separate the upper
5 5435X-(temp) 1 Element Assembly, and lower housings. Remove Element Assembly (5) and
specify temperature in ˚F Element O-ring Seal (4). Remove Housing Gasket (or O-
6 5695 1 Gasket (prior to
Serial No. A801) ring in later versions) and clean any foreign material from
6 11090L001 1 O-ring (after Serial No. A801) sealing surfaces. Lubricate new Element O-ring Seal (4)
For Model EL, EF (except EFSK, EMSK) with a good grade of petroleum grease and insert in the
groved sleeve in the Upper Housing (1). Insert Element
4 1919L001 1 O-ring, Viton Assembly (5) through Element Seal (4) with a twisting
5 5435X-(temp) 1 Element Assembly, motion. Install housing seal O-ring (6), or Housing Gasket,
specify temperature in ˚F
6 5695 1 Gasket (prior to around the Element Assembly Flange and bolt on Lower
Serial No. A801) Housing (2).
6 11090L002 1 O-ring (after Serial No. A801)
For Model EFSK Installation
4 1919 1 O-ring, Buna N
4 1919L001 1 O-ring, Viton (brown) AMOT Thermostatic Valves operate in any position and
5 5435X-(temp) 1 Element Assembly, may be located at the convenience of the system designer.
specify temperature in ˚F The valve can be supported by the connecting pipe but
6 10899 1 Housing Seal
should not be subjected to excessive bending. Line up the
For Model EM and EMSK piping before tightening the connecting bolts or the pipe
4 1919 1 O-ring, Buna N threads.
4 1919L001 1 O-ring, Viton (brown)
5 10912X-(temp) 1 Element Assembly for EMSK, If the valve is mounted at the high point of the system, the
specify temperature in ˚F system should be properly vented to prevent trapping air at
5 9831X-(temp) 1 Element Assembly for EM, the temperature element assemblies.
specify temperature in ˚F
6 10899 1 Housing Seal
21 11152L001 1 Stem Seal, Buna N For piping diagrams regarding specific applications, refer to
21 1152L002 1 Stem Seal, Viton (brown) Form 913, AMOT Thermostatic Valves General Informa-
tion.
AMOT Controls Corporation AMOT Controls Ltd. AMOT Controls Corporation
401 First Street Western Way 230 Orchard Road
Richmond, CA 94801 Bury St. Edmunds IP33 3SZ # 09-230 Faber House
Tel: (510) 236-8300 Suffolk England Singapore 238854
Fax: (510) 234-9950 Tel: (01284) 762222 Tel: (65) 235-8187
Fax: (01284) 760256 Fax: (65) 235-8869
©1997 AMOT Controls Corporation Form 594 A971
