PROJECT REPORT

ON
INDUSTRIAL TRAINING REPORT

Submitted in partial fulfilment of the requirement for the Award of the

degree of Diploma’s in Technology in Mechanical Engineering

SUBMITTED BY
Name: Aditya Gupta
Roll No:

SUBMITTED TO
Department of Mechanical Engineering
Sahasra Electronics Pvt. Ltd to Ram-eesh Institute of
Engineering and Technology
(Session: 2023-24)

1|Page
 ACKNOWLEDGEMENT

I have taken efforts in this training However, it would not have been
possible without the kind support and help of many individuals. I would like
to extend my sincere thanks to all of them

I am thankful to the Head of the Mechanical Engineering Department.

Chandra Sehkar Azad sir, and all the Faculty Members and Technical Staff
for making all the facilities available and for providing me the unstinting
support and guidance in the absence of which the training would have been
the shadow of its present form

I express my sincere gratitude to the Hon'ble Principal Dr.D.K. Rajoriya for

their constant guidance and motivation towards the betterment of my
training

My thanks and appreciations also go to my Training Cell for understanding

my career needs and supporting whenever needed

I would like to express my special gratitude and thanks to all the industry
experts for giving me such attention and time

2|Page
 TABLE OF CONTENTS
S.NO. TOPIC PAGE NO.

1 CERTIFICATE 5
2 ACKNOWLEDGEMENT 6
3 ROLE AND RESPONSIBILITIES 7
4 PERSONAL ENGINEERING 8
ACTIVITY
5 INTRODUCTION 9
6 POWER SUPPLIES 12
7 HISTORY 14
8 PROCESSES 22
9 WORKING PRINCIPLE 56
10 EXPERIMENTAL MODELING 60
11 ADVANTAGES 61
12 APPLICATIONS 61
13 CONCLUSION 62

3|Page
 ACKNOWLEDGEMENT
I have taken efforts in this training However, it would not have been
possible without the kind support and help of many individuals. I would like
to extend my sincere thanks to all of them

I am thankful to the Head of the Mechanical Engineering Department.

Chandra Sehkar Azad sir, and all the Faculty Members and Technical Staff
for making all the facilities available and for providing me the unstinting
support and guidance in the absence of which the training would have been
the shadow of its present form

I express my sincere gratitude to the Hon'ble Principal Dr.D.K. Rajoriya for

their constant guidance and motivation towards the betterment of my
training

My thanks and appreciations also go to my Training Cell for understanding

my career needs and supporting whenever needed

I would like to express my special gratitude and thanks to all the industry
experts for giving me such attention and time

4|Page
Role and Responsibilities

My roles and responsibilities includes:

 Prepare a requirement document to reach expectations of project and to

come up with functionalities which are needed to be implemented.
 Documentation of expected output for various aspects with accepted
margin error was also documented.
 To design overall system based on workflow requirements.
 Discussion with the project guide and Head of Department on ways to
improve the design and to optimize performance.
 Choosing suitable components and methods based on the configurations
availability and requirements.
 Testing and remedies.
 Recommendations

As a trainee mechanical engineer, I wanted to work on a project work

that would showcase my engineering knowledge. I got the opportunity
to work on WELDING MACHINE. This project was very important as it
evaluated my skills and talents in my company.

5|Page
PERSONAL ENGINEERING ACTIVITY

As a mechanical engineer, before undertaking any task I checked the

feasibility of the project. In this project, my role is as team members.
This report provides an insight into the design and fabrication of a
WELDING MACHINE.

I wanted to know more details of the project before commencing;

hence, I researched the topic thoroughly by referring to journals and
articles online. Additionally, I obtained more information by taking
references about the topic.

6|Page
INTRODUCTION

Arc welding is a process that is used to join metal to metal by using electricity to
create heat enough to melt metal, and the melted metals when cool result in a
binding of the metals. It is a type of welding that uses a welding power supply to
create an electric arc between an electrode and the base material to melt the
metals at the welding point. They can use either direct (DC) or alternating (AC)
current, and consumable or non-consumable electrodes. The welding region is
usually protected by some type of shielding gas, vapor, or slag. Arc welding
processes may be manual, semi-automatic, or fully automated. First developed in
the late part of the 19th century, arc welding became commercially important in
shipbuilding during the Second World War. Today it remains an important process
for the fabrication of steel structures and vehicles.

WELDING

Welding is a fabrication or sculptural process that joins materials, usually metals

or thermoplastics, by causing fusion, which is distinct from lower temperature
metal-joining techniques such as brazing and soldering, which do not melt the
base metal. In addition to melting the base metal, a filler material is often added
to the joint to form a pool of molten material (the weld pool) that cools to form a
joint that can be as strong, or even stronger, than the base material. Pressure may
also be used in conjunction with heat, or by itself, to produce a weld.

Although less common, there are also solid state welding processes such as
friction welding or shielded active gas welding in which metal does not melt.

7|Page
Some of the best known welding methods include:

 Shielded metal arc welding (SMAW) – also known as "stick welding or electric
welding", uses an electrode that has flux around it to protect the weld puddle.
The electrode holder holds the electrode as it slowly melts away. Slag protects
the weld puddle from atmospheric contamination.
 Gas tungsten arc welding (GTAW) – also known as TIG (tungsten, inert gas),
uses a non-consumable tungsten electrode to produce the weld. The weld
area is protected from atmospheric contamination by an inert shielding gas
such as argon or helium.
 Gas metal arc welding (GMAW) – commonly termed MIG (metal, inert gas),
uses a wire feeding gun that feeds wire at an adjustable speed and flows an
argon-based shielding gas or a mix of argon and carbon dioxide (CO2) over the
weld puddle to protect it from atmospheric contamination.
 Flux-cored arc welding (FCAW) – almost identical to MIG welding except it uses
a special tubular wire filled with flux; it can be used with or without shielding
gas, depending on the filler.
 Submerged arc welding (SAW) – uses an automatically fed consumable
electrode and a blanket of granular fusible flux. The molten weld and the arc
zone are protected from atmospheric contamination by being "submerged"
under the flux blanket.
 Electroslag welding (ESW) – a highly productive, single pass welding process
for thicker materials between 1 inch (25 mm) and 12 inches (300 mm) in a
vertical or close to vertical position.

8|Page
Many different energy sources can be used for welding, including a gas flame, an
electric arc, a laser, an electron beam, friction, and ultrasound. While often an
industrial process, welding may be performed in many different environments,
including in open air, under water, and in outer space. Welding is a hazardous
undertaking and precautions are required to avoid burns, electric shock, vision
damage, inhalation of poisonous gases and fumes, and exposure to intense
ultraviolet radiation.

Until the end of the 19th century, the only welding process was forge welding,
which blacksmiths had used for centuries to join iron and steel by heating and
hammering. Arc welding and oxyfuel welding were among the first processes to
develop late in the century, and electric resistance welding followed soon after.
Welding technology advanced quickly during the early 20th century as the world
wars drove the demand for reliable and inexpensive joining methods. Following
the wars, several modern welding techniques were developed, including manual
methods like SMAW, now one of the most popular welding methods, as well as
semi-automatic and automatic processes such as GMAW, SAW, FCAW and ESW.
Developments continued with the invention of laser beam welding, electron
beam welding, magnetic pulse welding (MPW), and friction stir welding in the
latter half of the century. Today, the science continues to advance. Robot welding
is commonplace in industrial settings, and researchers continue to develop new
welding methods and gain greater understanding of weld quality.

9|Page
POWER SUPPLIES

Engine driven welder capable of AC/DC welding.

A diesel powered welding generator (the electric generator is on the left) as used
in Indonesia.

To supply the electrical energy necessary for arc welding processes, a number of
different power supplies can be used. The most common classification is constant
current power supplies and constant voltage power supplies. In arc welding, the
voltage is directly related to the length of the arc, and the current is related to the
amount of heat input. Constant current power supplies are most often used for

10 | P a g e
manual welding processes such as gas tungsten arc welding and shielded metal
arc welding, because they maintain a relatively constant current even as the
voltage varies. This is important because in manual welding, it can be difficult to
hold the electrode perfectly steady, and as a result, the arc length and thus
voltage tend to fluctuate. Constant voltage power supplies hold the voltage
constant and vary the current, and as a result, are most often used for automated
welding processes such as gas metal arc welding, flux cored arc welding, and
submerged arc welding. In these processes, arc length is kept constant, since any
fluctuation in the distance between the wire and the base material is quickly
rectified by a large change in current. For example, if the wire and the base
material get too close, the current will rapidly increase, which in turn causes the
heat to increase and the tip of the wire to melt, returning it to its original
separation distance.

The direction of current used in arc welding also plays an important role in
welding. Consumable electrode processes such as shielded metal arc welding and
gas metal arc welding generally use direct current, but the electrode can be
charged either positively or negatively. In welding, the positively charged anode
will have a greater heat concentration (around 60%) and, as a result, changing the
polarity of the electrode affects weld properties. If the electrode is positively
charged, it will melt more quickly, increasing weld penetration and welding speed.
Alternatively, a negatively charged electrode results in more shallow welds. Non-
consumable electrode processes, such as gas tungsten arc welding, can use either
type of direct current (DC), as well as alternating current (AC). With direct current
however, because the electrode only creates the arc and does not provide filler
material, a positively charged electrode causes shallow welds, while a negatively
11 | P a g e
charged electrode makes deeper welds.[4] Alternating current rapidly moves
between these two, resulting in medium-penetration welds. One disadvantage of
AC, the fact that the arc must be re-ignited after every zero crossing, has been
addressed with the invention of special power units that produce a square wave
pattern instead of the normal sine wave, eliminating low-voltage time after the
zero crossings and minimizing the effects of the problem. [5]

HISTORY
The history of joining metals goes back several millennia. Called forge welding,
the earliest examples come from the Bronze and Iron Ages in Europe and the
Middle East. The ancient Greek historian Herodotus states in The Histories of the
5th century BC that Glaucus of Chios "was the man who single-handedly invented
iron welding".[1] Welding was used in the construction of the Iron pillar of Delhi,
erected in Delhi, India about 310 AD and weighing 5.4 metric tons.[2]

The Middle Ages brought advances in forge welding, in which blacksmiths

pounded heated metal repeatedly until bonding occurred. In 1540, Vannoccio
Biringuccio published De la pirotechnia, which includes descriptions of the forging
operation.[3] Renaissance craftsmen were skilled in the process, and the industry
continued to grow during the following centuries.[3]

In 1800, Sir Humphry Davy discovered the short-pulse electrical arc and presented
his results in 1801. In 1802, Russian scientist Vasily Petrov created the continuous
electric arc, and subsequently published "News of Galvanic-Voltaic Experiments"
in 1803, in which he described experiments carried out in 1802. Of great

12 | P a g e
importance in this work was the description of a stable arc discharge and the
indication of its possible use for many applications, one being melting metals.[9]
In 1808, Davy, who was unaware of Petrov's work, rediscovered the continuous
electric arc. In 1881–82 inventors Nikolai Benardos (Russian) and Stanisław
Olszewski (Polish)[10] created the first electric arc welding method known as
carbon arc welding using carbon electrodes. In 1905, Russian scientist Vladimir
Mitkevich proposed using a three-phase electric arc for welding. In 1919,
alternating current welding was invented by C. J. Holslag but did not become
popular for another decade.

Resistance welding was also developed during the final decades of the 19th
century, with the first patents going to Elihu Thomson in 1885, At first, oxyfuel
welding was one of the more popular welding methods due to its portability and
relatively low cost. As the 20th century progressed, however, it fell out of favor
for industrial applications. It was largely replaced with arc welding, as metal
coverings (known as flux) for the electrode that stabilize the arc and shield the
base material from impurities continued to be developed.

13 | P a g e
 Bridge of Maurzyce

World War I caused a major surge in the use of welding processes, with the
various military powers attempting to determine which of the several new
welding processes would be best. The British primarily used arc welding, even
constructing a ship, the "Fullagar" with an entirely welded hull. Arc welding was
first applied to aircraft during the war as well, as some German airplane fuselages
were constructed using the process. Also noteworthy is the first welded road
bridge in the world, the Maurzyce Bridge designed by Stefan Bryła of the Lwów
University of Technology in 1927, and built across the river Słudwia near Łowicz,
Poland in 1928.

14 | P a g e
 Acetylene welding on cylinder water jacket, 1918

During the 1920s, major advances were made in welding technology, including
the introduction of automatic welding in 1920, in which electrode wire was fed
continuously. Shielding gas became a subject receiving much attention, as
scientists attempted to protect welds from the effects of oxygen and nitrogen in
the atmosphere. Porosity and brittleness were the primary problems, and the
solutions that developed included the use of hydrogen, argon, and helium as
welding atmospheres. During the following decade, further advances allowed for
the welding of reactive metals like aluminum and magnesium.

During the middle of the century, many new welding methods were invented. In
1930, Kyle Taylor was responsible for the release of stud welding, which soon
became popular in shipbuilding and construction. Submerged arc welding was
invented the same year and continues to be popular today. In 1932 a Russian,
Konstantin Khrenov successfully implemented the first underwater electric arc
welding. Gas tungsten arc welding, after decades of development, was finally

15 | P a g e
perfected in 1941, and gas metal arc welding followed in 1948, allowing for fast
welding of non-ferrous materials but requiring expensive shielding gases. Shielded
metal arc welding was developed during the 1950s, using a flux-coated
consumable electrode, and it quickly became the most popular metal arc welding
process. In 1957, the flux-cored arc welding process debuted, in which the self-
shielded wire electrode could be used with automatic equipment, resulting in
greatly increased welding speeds, and that same year, plasma arc welding was
invented. Electroslag welding was introduced in 1958, and it was followed by its
cousin, electrogas welding, in 1961. In 1953 the Soviet scientist N. F. Kazakov
proposed the diffusion bonding method.

ARC WELDING HISTORY

While examples of forge welding go back to the Bronze Age and the Iron Age, arc
welding did not come into practice until much later.

In 1800 Sir Humphry Davy discovered the short pulsed electric arcs.
Independently a Russian physicist Vasily Petrov discovered the continuous electric
arc in 1802 and subsequently proposed its possible practical applications,
including welding. Arc welding was first developed when Nikolai Benardos
presented arc welding of metals using a carbon electrode at the International
Exposition of Electricity, Paris in 1881, which was patented together with
Stanisław Olszewski in 1887.

Competing welding processes such as resistance welding and oxyfuel welding

were developed during this time as well; but both, especially the latter, faced stiff
competition from arc welding especially after metal coverings (known as flux) for

16 | P a g e
the electrode, to stabilize the arc and shield the base material from impurities,
continued to be developed.

A young woman arc welding in a munitions factory in Australia in 1943.

During World War I welding started to be used in shipbuilding in Great Britain in

place of riveted steel plates. The Americans also became more accepting of the
new technology when the process allowed them to repair their ships quickly after
a German attack in the New York Harbor at the beginning of the war. [31] Arc
welding was first applied to aircraft during the war as well, and some German
airplane fuselages were constructed using this process. [32] In 1919, the British
shipbuilder Cammell Laird started construction of merchant ship, the "Fullagar",
with an entirely welded hull;[33] she was launched in 1921.[34]

During the 1920s, major advances were made in welding technology, including
the 1920 introduction of automatic welding in which electrode wire was
continuously fed. Shielding gas became a subject receiving much attention as
scientists attempted to protect welds from the effects of oxygen and nitrogen in
the atmosphere. Porosity and brittleness were the primary problems and the
solutions that developed included the use of hydrogen, argon, and helium as

17 | P a g e
welding atmospheres.[35] During the following decade, further advances allowed
for the welding of reactive metals such as aluminum and magnesium.

During the middle of the century, many new welding methods were invented.
Submerged arc welding was invented in 1930 and continues to be popular today.
In 1932 a Russian, Konstantin Khrenov successfully implemented the first
underwater electric arc welding. Gas tungsten arc welding, after decades of
development, was finally perfected in 1941 and gas metal arc welding followed in
1948, allowing for fast welding of non-ferrous materials but requiring expensive
shielding gases. Using a consumable electrode and a carbon dioxide atmosphere
as a shielding gas, it quickly became the most popular metal arc welding process.
In 1957, the flux-cored arc welding process debuted in which the self-shielded
wire electrode could be used with automatic equipment, resulting in greatly
increased welding speeds. In that same year, plasma arc welding was invented.
Electroslag welding was released in 1958 and was followed by its cousin,
electrogas welding, in 1961.

Processes
Arc welding

Man welding a metal structure in a newly constructed house in Bengaluru, India

18 | P a g e
These processes use a welding power supply to create and maintain an electric
arc between an electrode and the base material to melt metals at the welding
point. They can use either direct (DC) or alternating (AC) current, and consumable
or non-consumable electrodes. The welding region is sometimes protected by
some type of inert or semi-inert gas, known as a shielding gas, and filler material
is sometimes used as well.

Power supplies

To supply the electrical power necessary for arc welding processes, a variety of
different power supplies can be used. The most common welding power supplies
are constant current power supplies and constant voltage power supplies. In arc
welding, the length of the arc is directly related to the voltage, and the amount of
heat input is related to the current. Constant current power supplies are most
often used for manual welding processes such as gas tungsten arc welding and
shielded metal arc welding, because they maintain a relatively constant current
even as the voltage varies. This is important because in manual welding, it can be
difficult to hold the electrode perfectly steady, and as a result, the arc length and
thus voltage tend to fluctuate. Constant voltage power supplies hold the voltage
constant and vary the current, and as a result, are most often used for automated
welding processes such as gas metal arc welding, flux cored arc welding, and
submerged arc welding. In these processes, arc length is kept constant, since any
fluctuation in the distance between the wire and the base material is quickly
rectified by a large change in current.

The type of current used plays an important role in arc welding. Consumable
electrode processes such as shielded metal arc welding and gas metal arc welding

19 | P a g e
generally use direct current, but the electrode can be charged either positively or
negatively. In welding, the positively charged anode will have a greater heat
concentration, and as a result, changing the polarity of the electrode affects weld
properties. If the electrode is positively charged, the base metal will be hotter,
increasing weld penetration and welding speed. Alternatively, a negatively
charged electrode results in more shallow welds. Nonconsumable electrode
processes, such as gas tungsten arc welding, can use either type of direct current,
as well as alternating current. However, with direct current, because the
electrode only creates the arc and does not provide filler material, a positively
charged electrode causes shallow welds, while a negatively charged electrode
makes deeper welds. Alternating current rapidly moves between these two,
resulting in medium-penetration welds. One disadvantage of AC, the fact that the
arc must be re-ignited after every zero crossing, has been addressed with the
invention of special power units that produce a square wave pattern instead of
the normal sine wave, making rapid zero crossings possible and minimizing the
effects of the problem.

Processes

One of the most common types of arc welding is shielded metal arc welding
(SMAW);[28] it is also known as manual metal arc welding (MMA) or stick welding.
Electric current is used to strike an arc between the base material and
consumable electrode rod, which is made of filler material (typically steel) and is
covered with a flux that protects the weld area from oxidation and contamination
by producing carbon dioxide (CO2) gas during the welding process. The electrode
core itself acts as filler material, making a separate filler unnecessary.

20 | P a g e
The process is versatile and can be performed with relatively inexpensive
equipment, making it well suited to shop jobs and field work. An operator can
become reasonably proficient with a modest amount of training and can achieve
mastery with experience. Weld times are rather slow, since the consumable
electrodes must be frequently replaced and because slag, the residue from the
flux, must be chipped away after welding. Furthermore, the process is generally
limited to welding ferrous materials, though special electrodes have made
possible the welding of cast iron, nickel, aluminum, copper, and other metals.

Diagram of arc and weld area, in shielded metal arc welding.

1. Coating Flow
2. Rod
3. Shield Gas
4. Fusion
5. Base metal
6. Weld metal
7. Solidified Slag
Gas metal arc welding (GMAW), also known as metal inert gas or MIG welding, is
a semi-automatic or automatic process that uses a continuous wire feed as an
electrode and an inert or semi-inert gas mixture to protect the weld from

21 | P a g e
contamination. Since the electrode is continuous, welding speeds are greater for
GMAW than for SMAW.
A related process, flux-cored arc welding (FCAW), uses similar equipment but uses
wire consisting of a steel electrode surrounding a powder fill material. This cored
wire is more expensive than the standard solid wire and can generate fumes
and/or slag, but it permits even higher welding speed and greater metal
penetration.
Gas tungsten arc welding (GTAW), or tungsten inert gas (TIG) welding, is a manual
welding process that uses a nonconsumable tungsten electrode, an inert or semi-
inert gas mixture, and a separate filler material. Especially useful for welding thin
materials, this method is characterized by a stable arc and high quality welds, but
it requires significant operator skill and can only be accomplished at relatively low
speeds.
GTAW can be used on nearly all weldable metals, though it is most often applied
to stainless steel and light metals. It is often used when quality welds are
extremely important, such as in bicycle, aircraft and naval applications. A related
process, plasma arc welding, also uses a tungsten electrode but uses plasma gas
to make the arc. The arc is more concentrated than the GTAW arc, making
transverse control more critical and thus generally restricting the technique to a
mechanized process. Because of its stable current, the method can be used on a
wider range of material thicknesses than can the GTAW process and it is much
faster. It can be applied to all of the same materials as GTAW except magnesium,
and automated welding of stainless steel is one important application of the
process. A variation of the process is plasma cutting, an efficient steel cutting
process.

22 | P a g e
Submerged arc welding (SAW) is a high-productivity welding method in which the
arc is struck beneath a covering layer of flux. This increases arc quality, since
contaminants in the atmosphere are blocked by the flux. The slag that forms on
the weld generally comes off by itself, and combined with the use of a continuous
wire feed, the weld deposition rate is high. Working conditions are much
improved over other arc welding processes, since the flux hides the arc and
almost no smoke is produced. The process is commonly used in industry,
especially for large products and in the manufacture of welded pressure vessels.
Other arc welding processes include atomic hydrogen welding, electroslag
welding, electrogas welding, and stud arc welding.

Gas welding
Main article: Oxy-fuel welding and cutting

The most common gas welding process is oxyfuel welding, [13] also known as
oxyacetylene welding. It is one of the oldest and most versatile welding
processes, but in recent years it has become less popular in industrial
applications. It is still widely used for welding pipes and tubes, as well as repair
work.

The equipment is relatively inexpensive and simple, generally employing the

combustion of acetylene in oxygen to produce a welding flame temperature of
about 3100 °C. The flame, since it is less concentrated than an electric arc, causes
slower weld cooling, which can lead to greater residual stresses and weld
distortion, though it eases the welding of high alloy steels. A similar process,
generally called oxyfuel cutting, is used to cut metals.

23 | P a g e
Resistance
Main article: Resistance welding

Resistance welding involves the generation of heat by passing current through the
resistance caused by the contact between two or more metal surfaces. Small
pools of molten metal are formed at the weld area as high current (1000–100,000
A) is passed through the metal. In general, resistance welding methods are
efficient and cause little pollution, but their applications are somewhat limited
and the equipment cost can be high.

Spot welder

Spot welding is a popular resistance welding method used to join overlapping

metal sheets of up to 3 mm thick. Two electrodes are simultaneously used to
clamp the metal sheets together and to pass current through the sheets. The
advantages of the method include efficient energy use, limited workpiece
deformation, high production rates, easy automation, and no required filler
materials. Weld strength is significantly lower than with other welding methods,
making the process suitable for only certain applications. It is used extensively in
the automotive industry—ordinary cars can have several thousand spot welds
made by industrial robots. A specialized process, called shot welding, can be used
to spot weld stainless steel.

24 | P a g e
Like spot welding, seam welding relies on two electrodes to apply pressure and
current to join metal sheets. However, instead of pointed electrodes, wheel-
shaped electrodes roll along and often feed the workpiece, making it possible to
make long continuous welds. In the past, this process was used in the
manufacture of beverage cans, but now its uses are more limited. Other
resistance welding methods include butt welding, flash welding, projection
welding, and upset welding.

Energy beam

Energy beam welding methods, namely laser beam welding and electron beam
welding, are relatively new processes that have become quite popular in high
production applications. The two processes are quite similar, differing most
notably in their source of power. Laser beam welding employs a highly focused
laser beam, while electron beam welding is done in a vacuum and uses an
electron beam. Both have a very high energy density, making deep weld
penetration possible and minimizing the size of the weld area. Both processes are
extremely fast, and are easily automated, making them highly productive. The
primary disadvantages are their very high equipment costs (though these are
decreasing) and a susceptibility to thermal cracking. Developments in this area
include laser-hybrid welding, which uses principles from both laser beam welding
and arc welding for even better weld properties, laser cladding, and x-ray welding.

25 | P a g e
Solid-state

Solid-state welding processes classification chart

Like the first welding process, forge welding, some modern welding methods do
not involve the melting of the materials being joined. One of the most popular,
ultrasonic welding, is used to connect thin sheets or wires made of metal or
thermoplastic by vibrating them at high frequency and under high pressure. [40]
The equipment and methods involved are similar to that of resistance welding,
but instead of electric current, vibration provides energy input. Welding metals
with this process does not involve melting the materials; instead, the weld is
formed by introducing mechanical vibrations horizontally under pressure. When
welding plastics, the materials should have similar melting temperatures, and the
vibrations are introduced vertically. Ultrasonic welding is commonly used for
26 | P a g e
making electrical connections out of aluminum or copper, and it is also a very
common polymer welding process.

Another common process, explosion welding, involves the joining of materials by

pushing them together under extremely high pressure. The energy from the
impact plasticizes the materials, forming a weld, even though only a limited
amount of heat is generated. The process is commonly used for welding dissimilar
materials, such as the welding of aluminum with steel in ship hulls or compound
plates. Other solid-state welding processes include friction welding (including
friction stir welding), magnetic pulse welding, co-extrusion welding, cold welding,
diffusion bonding, exothermic welding, high frequency welding, hot pressure
welding, induction welding, and roll welding.

Geometry
Main article: Welding joint

Common welding joint types – (1) Square butt joint, (2) V butt joint, (3) Lap joint,
(4) T-joint

Welds can be geometrically prepared in many different ways. The five basic types
of weld joints are the butt joint, lap joint, corner joint, edge joint, and T-joint
27 | P a g e
(a variant of this last is the cruciform joint). Other variations exist as well—for
example, double-V preparation joints are characterized by the two pieces of
material each tapering to a single center point at one-half their height. Single-U
and double-U preparation joints are also fairly common—instead of having
straight edges like the single-V and double-V preparation joints, they are curved,
forming the shape of a U. Lap joints are also commonly more than two pieces
thick—depending on the process used and the thickness of the material, many
pieces can be welded together in a lap joint geometry.

Many welding processes require the use of a particular joint design; for example,
resistance spot welding, laser beam welding, and electron beam welding are most
frequently performed on lap joints. Other welding methods, like shielded metal
arc welding, are extremely versatile and can weld virtually any type of joint. Some
processes can also be used to make multipass welds, in which one weld is allowed
to cool, and then another weld is performed on top of it. This allows for the
welding of thick sections arranged in a single-V preparation joint, for example.

The cross-section of a welded butt joint, with the darkest gray representing the
weld or fusion zone, the medium gray the heat-affected zone, and the lightest
gray the base material.

After welding, a number of distinct regions can be identified in the weld area. The
weld itself is called the fusion zone—more specifically, it is where the filler metal
was laid during the welding process. The properties of the fusion zone depend
primarily on the filler metal used, and its compatibility with the base materials. It

28 | P a g e
is surrounded by the heat-affected zone, the area that had its microstructure and
properties altered by the weld. These properties depend on the base material's
behavior when subjected to heat. The metal in this area is often weaker than both
the base material and the fusion zone, and is also where residual stresses are
found.

Quality
Main article: Weld quality assurance

The blue area results from oxidation at a corresponding temperature of 600 °F

(316 °C). This is an accurate way to identify temperature, but does not represent
the HAZ width. The HAZ is the narrow area that immediately surrounds the
welded base metal.

Many distinct factors influence the strength of welds and the material around
them, including the welding method, the amount and concentration of energy
input, the weldability of the base material, filler material, and flux material, the
design of the joint, and the interactions between all these factors. [46] To test the

29 | P a g e
quality of a weld, either destructive or nondestructive testing methods are
commonly used to verify that welds are free of defects, have acceptable levels of
residual stresses and distortion, and have acceptable heat-affected zone (HAZ)
properties. Types of welding defects include cracks, distortion, gas inclusions
(porosity), non-metallic inclusions, lack of fusion, incomplete penetration,
lamellar tearing, and undercutting.

The metalworking industry has instituted specifications and codes to guide

welders, weld inspectors, engineers, managers, and property owners in proper
welding technique, design of welds, how to judge the quality of Welding
Procedure Specification, how to judge the skill of the person performing the weld,
and how to ensure the quality of a welding job. [46] Methods such as visual
inspection, radiography, ultrasonic testing, phased-array ultrasonics, dye
penetrant inspection, magnetic particle inspection, or industrial computed
tomography can help with detection and analysis of certain defects.

Heat-affected zone
The effects of welding on the material surrounding the weld can be detrimental—
depending on the materials used and the heat input of the welding process used,
the HAZ can be of varying size and strength. The thermal diffusivity of the base
material plays a large role—if the diffusivity is high, the material cooling rate is
high and the HAZ is relatively small. Conversely, a low diffusivity leads to slower
cooling and a larger HAZ. The amount of heat injected by the welding process
plays an important role as well, as processes like oxyacetylene welding have an
unconcentrated heat input and increase the size of the HAZ. Processes like laser
beam welding give a highly concentrated, limited amount of heat, resulting in a

30 | P a g e
small HAZ. Arc welding falls between these two extremes, with the individual
processes varying somewhat in heat input.

Lifetime extension with aftertreatment methods

The durability and life of dynamically loaded, welded steel structures is

determined in many cases by the welds, particular the weld transitions. Through
selective treatment of the transitions by grinding (abrasive cutting), shot peening,
High Frequency Impact Treatment, etc. the durability of many designs increase
significantly.

Metallurgy

Most solids used are engineering materials consisting of crystalline solids in which
the atoms or ions are arranged in a repetitive geometric pattern which is known
as a lattice structure. The only exception is material that is made from glass which
is a combination of a supercooled liquid and polymers which are aggregates of
large organic molecules.

Crystalline solids cohesion is obtained by a metallic or chemical bond which is

formed between the constituent atoms. Chemical bonds can be grouped into two
types consisting of ionic and covalent. To form an ionic bond, either a valence or
bonding electron separates from one atom and becomes attached to another
atom to form oppositely charged ions. The bonding in the static position is when
the ions occupy an equilibrium position where the resulting force between them
is zero. When the ions are exerted in tension force, the inter-ionic spacing

31 | P a g e
increases creating an electrostatic attractive force, while a repulsing force under
compressive force between the atomic nuclei is dominant.

Covalent bonding takes place when one of the constituent atoms loses one or
more electrons, with the other atom gaining the electrons, resulting in an
electron cloud that is shared by the molecule as a whole. In both ionic and
covalent bonding the location of the ions and electrons are constrained relative to
each other, thereby resulting in the bond being characteristically brittle.

Metallic bonding can be classified as a type of covalent bonding for which the
constituent atoms of the same type and do not combine with one another to
form a chemical bond. Atoms will lose an electron(s) forming an array of positive
ions. These electrons are shared by the lattice which makes the electron cluster
mobile, as the electrons are free to move as well as the ions. For this, it gives
metals their relatively high thermal and electrical conductivity as well as being
characteristically ductile.

Three of the most commonly used crystal lattice structures in metals are the
body-centred cubic, face-centred cubic and close-packed hexagonal. Ferritic steel
has a body-centred cubic structure and austenitic steel, non-ferrous metals like
aluminum, copper and nickel have the face-centred cubic structure.

Ductility is an important factor in ensuring the integrity of structures by enabling

them to sustain local stress concentrations without fracture. In addition,
structures are required to be of an acceptable strength, which is related to a
material's yield strength. In general, as the yield strength of a material increases,
there is a corresponding reduction in fracture toughness.

32 | P a g e
Unusual conditions

Underwater welding
While many welding applications are done in controlled environments such as
factories and repair shops, some welding processes are commonly used in a wide
variety of conditions, such as open air, underwater, and vacuums (such as space).
In open-air applications, such as construction and outdoors repair, shielded metal
arc welding is the most common process. Processes that employ inert gases to
protect the weld cannot be readily used in such situations, because unpredictable
atmospheric movements can result in a faulty weld. Shielded metal arc welding is
also often used in underwater welding in the construction and repair of ships,
offshore platforms, and pipelines, but others, such as flux cored arc welding and
gas tungsten arc welding, are also common. Welding in space is also possible—it
was first attempted in 1969 by Russian cosmonauts, when they performed
experiments to test shielded metal arc welding, plasma arc welding, and electron
beam welding in a depressurized environment. Further testing of these methods
was done in the following decades, and today researchers continue to develop

33 | P a g e
methods for using other welding processes in space, such as laser beam welding,
resistance welding, and friction welding. Advances in these areas may be useful
for future endeavours similar to the construction of the International Space
Station, which could rely on welding for joining in space the parts that were
manufactured on Earth.

Safety issues

Arc welding with a welding helmet, gloves, and other protective clothing
Welding can be dangerous and unhealthy if the proper precautions are not taken.
However, using new technology and proper protection greatly reduces risks of
injury and death associated with welding. [52] Since many common welding
procedures involve an open electric arc or flame, the risk of burns and fire is
significant; this is why it is classified as a hot work process. To prevent injury,
welders wear personal protective equipment in the form of heavy leather gloves
and protective long-sleeve jackets to avoid exposure to extreme heat and flames.
Additionally, the brightness of the weld area leads to a condition called arc eye or
flash burns in which ultraviolet light causes inflammation of the cornea and can
burn the retinas of the eyes. Goggles and welding helmets with dark UV-filtering
face plates are worn to prevent this exposure. Since the 2000s, some helmets
have included a face plate which instantly darkens upon exposure to the intense
UV light. To protect bystanders, the welding area is often surrounded with
34 | P a g e
translucent welding curtains. These curtains, made of a polyvinyl chloride plastic
film, shield people outside the welding area from the UV light of the electric arc,
but can not replace the filter glass used in helmets.

A chamber designed to contain welding fumes for analysis

Welders are often exposed to dangerous gases and particulate matter. Processes
like flux-cored arc welding and shielded metal arc welding produce smoke
containing particles of various types of oxides. The size of the particles in question
tends to influence the toxicity of the fumes, with smaller particles presenting a
greater danger. This is because smaller particles have the ability to cross the
blood brain barrier. Fumes and gases, such as carbon dioxide, ozone, and fumes
containing heavy metals, can be dangerous to welders lacking proper ventilation
and training.[54] Exposure to manganese welding fumes, for example, even at low
levels (<0.2 mg/m3), may lead to neurological problems or to damage to the lungs,
liver, kidneys, or central nervous system. [55] Nano particles can become trapped in
the alveolar macrophages of the lungs and induce pulmonary fibrosis. [56] The use
of compressed gases and flames in many welding processes poses an explosion

35 | P a g e
and fire risk. Some common precautions include limiting the amount of oxygen in
the air, and keeping combustible materials away from the workplace.

Costs and trends

As an industrial process, the cost of welding plays a crucial role in manufacturing
decisions. Many different variables affect the total cost, including equipment cost,
labor cost, material cost, and energy cost.[57] Depending on the process,
equipment cost can vary, from inexpensive for methods like shielded metal arc
welding and oxyfuel welding, to extremely expensive for methods like laser beam
welding and electron beam welding. Because of their high cost, they are only used
in high production operations. Similarly, because automation and robots increase
equipment costs, they are only implemented when high production is necessary.
Labor cost depends on the deposition rate (the rate of welding), the hourly wage,
and the total operation time, including time spent fitting, welding, and handling
the part. The cost of materials includes the cost of the base and filler material,
and the cost of shielding gases. Finally, energy cost depends on arc time and
welding power demand.
For manual welding methods, labor costs generally make up the vast majority of
the total cost. As a result, many cost-saving measures are focused on minimizing
operation time. To do this, welding procedures with high deposition rates can be
selected, and weld parameters can be fine-tuned to increase welding speed.
Mechanization and automation are often implemented to reduce labor costs, but
this frequently increases the cost of equipment and creates additional setup time.
Material costs tend to increase when special properties are necessary, and energy
costs normally do not amount to more than several percent of the total welding
cost.

36 | P a g e
In recent years, in order to minimize labor costs in high production
manufacturing, industrial welding has become increasingly more automated,
most notably with the use of robots in resistance spot welding (especially in the
automotive industry) and in arc welding. In robot welding, mechanized devices
both hold the material and perform the weld [58] and at first, spot welding was its
most common application, but robotic arc welding increases in popularity as
technology advances. Other key areas of research and development include the
welding of dissimilar materials (such as steel and aluminum, for example) and
new welding processes, such as friction stir, magnetic pulse, conductive heat
seam, and laser-hybrid welding. Furthermore, progress is desired in making more
specialized methods like laser beam welding practical for more applications, such
as in the aerospace and automotive industries.
The trend of accelerating the speed at which welds are performed in the steel
erection industry comes at a risk to the integrity of the connection. Without
proper fusion to the base materials provided by sufficient arc time on the weld, a
project inspector cannot ensure the effective diameter of the puddle weld
therefore he or she cannot guarantee the published load capacities unless they
witness the actual installation.

Glass and plastic welding

37 | P a g e
The welding together of two tubes made from lead glass

A bowl made from cast-glass. The two halves are joined together by the weld
seam, running down the middle.
Glasses and certain types of plastics are commonly welded materials. Unlike
metals, which have a specific melting point, glasses and plastics have a melting
range, called the glass transition. When heating the solid material into this range,
it will generally become softer and more pliable. When it crosses through the
glass transition, it will become a very thick, sluggish, viscous liquid. Typically, this
viscous liquid will have very little surface tension, becoming a sticky, honey-like
consistency, so welding can usually take place by simply pressing two melted
surfaces together. The two liquids will generally mix and join at first contact. Upon
cooling through the glass transition, the welded piece will solidify as one solid
piece of amorphous material.

Glass welding
Main article: Glassblowing
Glass welding is a common practice during glassblowing. It is used very often in
the construction of lighting, neon signs, flashtubes, scientific equipment, and the
manufacture of dishes and other glassware. It is also used during glass casting for

38 | P a g e
joining the halves of glass molds, making items such as bottles and jars. Welding
glass is accomplished by heating the glass through the glass transition, turning it
into a thick, formable, liquid mass. Heating is usually done with a gas or oxy-gas
torch, or a furnace, because the temperatures for melting glass are often quite
high. This temperature may vary, depending on the type of glass. For example,
lead glass becomes a weldable liquid at around 1,600 °F (870 °C), and can be
welded with a simple propane torch. On the other hand, quartz glass (fused silica)
must be heated to over 3,000 °F (1,650 °C), but quickly loses its viscosity and
formability if overheated, so an oxyhydrogen torch must be used. Sometimes a
tube may be attached to the glass, allowing it to be blown into various shapes,
such as bulbs, bottles, or tubes. When two pieces of liquid glass are pressed
together, they will usually weld very readily. Welding a handle onto a pitcher can
usually be done with relative ease. However, when welding a tube to another
tube, a combination of blowing and suction, and pressing and pulling is used to
ensure a good seal, to shape the glass, and to keep the surface tension from
closing the tube in on itself. Sometimes a filler rod may be used, but usually not.
Because glass is very brittle in its solid state, it is often prone to cracking upon
heating and cooling, especially if the heating and cooling are uneven. This is
because the brittleness of glass does not allow for uneven thermal expansion.
Glass that has been welded will usually need to be cooled very slowly and evenly
through the glass transition, in a process called annealing, to relieve any internal
stresses created by a temperature gradient.
There are many types of glass, and it is most common to weld using the same
types. Different glasses often have different rates of thermal expansion, which can
cause them to crack upon cooling when they contract differently.

39 | P a g e
Glass can also be welded to metals and ceramics, although with metals the
process is usually more adhesion to the surface of the metal rather than a
commingling of the two materials. However, certain glasses will typically bond
only to certain metals. For example, lead glass bonds readily to copper or
molybdenum, but not to aluminum. Tungsten electrodes are often used in lighting
but will not bond to quartz glass, so the tungsten is often wetted with molten
borosilicate glass, which bonds to both tungsten and quartz. However, care must
be taken to ensure that all materials have similar coefficients of thermal
expansion to prevent cracking both when the object cools and when it is heated
again. Special alloys are often used for this purpose, ensuring that the coefficients
of expansion match, and sometimes thin, metallic coatings may be applied to a
metal to create a good bond with the glass.

Plastic welding
Main article: Plastic welding
Plastics are generally divided into two categories, which are "thermosets" and
"thermoplastics." A thermoset is a plastic in which a chemical reaction sets the
molecular bonds after first forming the plastic, and then the bonds cannot be
broken again without degrading the plastic. Thermosets cannot be melted,
therefore, once a thermoset has set it is impossible to weld it. Examples of
thermosets include epoxies, silicone, vulcanized rubber, polyester, and
polyurethane.
Thermoplastics, by contrast, form long molecular chains, which are often coiled or
intertwined, forming an amorphous structure without any long-range, crystalline
order. Some thermoplastics may be fully amorphous, while others have a partially

40 | P a g e
crystalline/partially amorphous structure. Both amorphous and semicrystalline
thermoplastics have a glass transition, above which welding can occur, but
semicrystallines also have a specific melting point which is above the glass
transition. Above this melting point, the viscous liquid will become a free-flowing
liquid (see rheological weldability for thermoplastics). Examples of thermoplastics
include polyethylene, polypropylene, polystyrene, polyvinylchloride (PVC), and
fluoroplastics like Teflon and Spectralon.
Welding thermoplastic is very similar to welding glass. The plastic first must be
cleaned and then heated through the glass transition, turning the weld-interface
into a thick, viscous liquid. Two heated interfaces can then be pressed together,
allowing the molecules to mix through intermolecular diffusion, joining them as
one. Then the plastic is cooled through the glass transition, allowing the weld to
solidify. A filler rod may often be used for certain types of joints. The main
differences between welding glass and plastic are the types of heating methods,
the much lower melting temperatures, and the fact that plastics will burn if
overheated. Many different methods have been devised for heating plastic to a
weldable temperature without burning it. Ovens or electric heating tools can be
used to melt the plastic. Ultrasonic, laser, or friction heating are other methods.
Resistive metals may be implanted in the plastic, which respond to induction
heating. Some plastics will begin to burn at temperatures lower than their glass
transition, so welding can be performed by blowing a heated, inert gas onto the
plastic, melting it while, at the same time, shielding it from oxygen. [63]
Many thermoplastics can also be welded using chemical solvents. When placed in
contact with the plastic, the solvent will begin to soften it, bringing the surface
into a thick, liquid solution. When two melted surfaces are pressed together, the

41 | P a g e
molecules in the solution mix, joining them as one. Because the solvent can
permeate the plastic, the solvent evaporates out through the surface of the
plastic, causing the weld to drop out of solution and solidify. A common use for
solvent welding is for joining PVC or ABS (acrylonitrile butadiene styrene) pipes
during plumbing, or for welding styrene and polystyrene plastics in the
construction of models. Solvent welding is especially effective on plastics like PVC
which burn at or below their glass transition, but may be ineffective on plastics
like Teflon or polyethylene that are resistant to chemical decomposition.[64]

Consumable electrode methods

Main articles: Shielded metal arc welding, Gas metal arc welding, Flux-cored arc
welding, and Submerged arc welding

Shielded metal arc welding

One of the most common types of arc welding is shielded metal arc welding
(SMAW), which is also known as manual metal arc welding (MMAW) or stick
welding. An electric current is used to strike an arc between the base material and
a consumable electrode rod or stick. The electrode rod is made of a material that

42 | P a g e
is compatible with the base material being welded and is covered with a flux that
gives off vapors that serve as a shielding gas and provide a layer of slag, both of
which protect the weld area from atmospheric contamination. The electrode core
itself acts as filler material, making a separate filler unnecessary. The process is
very versatile, requiring little operator training and inexpensive equipment.
However, weld times are rather slow, since the consumable electrodes must be
frequently replaced and because slag, the residue from the flux, must be chipped
away after welding.[7] Furthermore, the process is generally limited to welding
ferrous materials, though specialty electrodes have made possible the welding of
cast iron, nickel, aluminium, copper and other metals. The versatility of the
method makes it popular in a number of applications including repair work and
construction.[8]

Gas metal arc welding (GMAW), commonly called MIG (for metal/inert-gas), is a
semi-automatic or automatic welding process with a continuously fed
consumable wire acting as both electrode and filler metal, along with an inert or
semi-inert shielding gas flowed around the wire to protect the weld site from
contamination. Constant voltage, direct current power source is most commonly
used with GMAW, but constant current alternating current are used as well. With
continuously fed filler electrodes, GMAW offers relatively high welding speeds,
however the more complicated equipment reduces convenience and versatility in
comparison to the SMAW process. Originally developed for welding aluminium
and other non-ferrous materials in the 1940s, GMAW was soon economically
applied to steels. Today, GMAW is commonly used in industries such as the
automobile industry for its quality, versatility and speed. Because of the need to
maintain a stable shroud of shielding gas around the weld site, it can be
43 | P a g e
problematic to use the GMAW process in areas of high air movement such as
outdoors.[9]

Flux-cored arc welding (FCAW) is a variation of the GMAW technique. FCAW wire
is actually a fine metal tube filled with powdered flux materials. An externally
supplied shielding gas is sometimes used, but often the flux itself is relied upon to
generate the necessary protection from the atmosphere. The process is widely
used in construction because of its high welding speed and portability.

Submerged arc welding (SAW) is a high-productivity welding process in which the

arc is struck beneath a covering layer of granular flux. This increases arc quality,
since contaminants in the atmosphere are blocked by the flux. The slag that forms
on the weld generally comes off by itself and, combined with the use of a
continuous wire feed, the weld deposition rate is high. Working conditions are
much improved over other arc welding processes since the flux hides the arc and
no smoke is produced. The process is commonly used in industry, especially for
large products.[10] As the arc is not visible, it is typically automated. SAW is only
possible in the 1F (flat fillet), 2F (horizontal fillet), and 1G (flat groove) positions.

Non-consumable electrode methods

Gas tungsten arc welding (GTAW), or tungsten/inert-gas (TIG) welding, is a
manual welding process that uses a non-consumable electrode made of tungsten,
an inert or semi-inert gas mixture, and a separate filler material. Especially useful
for welding thin materials, this method is characterized by a stable arc and high
quality welds, but it requires significant operator skill and can only be
accomplished at relatively low speeds. It can be used on nearly all weldable

44 | P a g e
metals, though it is most often applied to stainless steel and light metals. It is
often used when quality welds are extremely important, such as in bicycle,
aircraft and naval applications.

A related process, plasma arc welding, also uses a tungsten electrode but uses
plasma gas to make the arc. The arc is more concentrated than the GTAW arc,
making transverse control more critical and thus generally restricting the
technique to a mechanized process. Because of its stable current, the method can
be used on a wider range of material thicknesses than can the GTAW process

Corrosion issues
Main articles: Hydrogen embrittlement and Galvanic corrosion

Some materials, notably high-strength steels, aluminium, and titanium alloys, are
susceptible to hydrogen embrittlement. If the electrodes used for welding contain
traces of moisture, the water decomposes in the heat of the arc and the liberated
hydrogen enters the lattice of the material, causing its brittleness. Stick electrodes
for such materials, with special low-hydrogen coating, are delivered in sealed
moisture-proof packaging. New electrodes can be used straight from the can, but
when moisture absorption may be suspected, they have to be dried by baking
(usually at 450 to 550 °C or 840 to 1,020 °F) in a drying oven. Flux used has to be
kept dry as well.

Some austenitic stainless steels and nickel-based alloys are prone to intergranular
corrosion. When subjected to temperatures around 700 °C (1,300 °F) for too long
a time, chromium reacts with carbon in the material, forming chromium carbide
and depleting the crystal edges of chromium, impairing their corrosion resistance

45 | P a g e
in a process called sensitization. Such sensitized steel undergoes corrosion in the
areas near the welds where the temperature-time was favorable for forming the
carbide. This kind of corrosion is often termed weld decay.

Knifeline attack (KLA) is another kind of corrosion affecting welds, impacting steels
stabilized by niobium. Niobium and niobium carbide dissolves in steel at very high
temperatures. At some cooling regimes, niobium carbide does not precipitate,
and the steel then behaves like unstabilized steel, forming chromium carbide
instead. This affects only a thin zone several millimeters wide in the very vicinity
of the weld, making it difficult to spot and increasing the corrosion speed.
Structures made of such steels have to be heated in a whole to about 1,000 °C
(1,830 °F), when the chromium carbide dissolves and niobium carbide forms. The
cooling rate after this treatment is not important.

Safety issues

Welding safety checklist

46 | P a g e
Welding can be a dangerous and unhealthy practice without the proper
precautions; however, with the use of new technology and proper protection the
risks of injury or death associated with welding can be greatly reduced.

Heat, fire, and explosion hazard

Because many common welding procedures involve an open electric arc or flame,
the risk of burns from heat and sparks is significant. To prevent them, welders
wear protective clothing in the form of heavy leather gloves and protective long
sleeve jackets to avoid exposure to extreme heat, flames, and sparks. The use of
compressed gases and flames in many welding processes also pose an explosion
and fire risk; some common precautions include limiting the amount of oxygen in
the air and keeping combustible materials away from the workplace.

Eye damage

Exposure to the brightness of the weld area leads to a condition called arc eye in
which ultraviolet light causes inflammation of the cornea and can burn the retinas
of the eyes. Welding goggles and helmets with dark face plates—much darker

47 | P a g e
than those in sunglasses or oxy-fuel goggles—are worn to prevent this exposure.
In recent years, new helmet models have been produced featuring a face plate
which automatically self-darkens electronically. To protect bystanders,
transparent welding curtains often surround the welding area. These curtains,
made of a polyvinyl chloride plastic film, shield nearby workers from exposure to
the UV light from the electric arc.

Inhaled matter
Welders are also often exposed to dangerous gases and particulate matter.
Processes like flux-cored arc welding and shielded metal arc welding produce
smoke containing particles of various types of oxides. The size of the particles in
question tends to influence the toxicity of the fumes, with smaller particles
presenting a greater danger. Additionally, many processes produce various gases
(most commonly carbon dioxide and ozone, but others as well) that can prove
dangerous if ventilation is inadequate.

Interference with pacemakers

Certain welding machines which use a high frequency alternating current
component have been found to affect pacemaker operation when within 2
meters of the power unit and 1 meter of the weld site.

48 | P a g e
WORKING PRINCIPLE :

1. Function of the Machine

A. Principle of Operation:
Welding is the joining of metals through coalescence by the use of either heat or
pressure or both. Coalescence is a term that means the joining of two materials to
become as one piece. The basic arc welder components consist of the machine
that generates the power, the electrode holder or wirefeed gun, a means of
shielding the weld as it forms, and protective equipment for the user.
Power sources vary with the type of welding being performed. A machine may be
either DC or AC, constant current or constant voltage. Selection is made by
amount and type of current required, the power available, and economic factors.
Heat and speed can be adjusted by varying the voltage and current generated.
This is necessary since a slower speed is required for thicker metals. Speed on a
wirefeed type is controlled by the rate at which the wire is fed.
Shielding of the weld as it forms is very important. The level of impurities directly
affects the strength of the weld. The molten metal is susceptible to impurities
such as oxygen and carbon deposits. A shield of gas covers the weld as it forms,
protecting it from the air. Shielding can be accomplished by either a coating on
the wire or welding rod (known as flux), or a gas. Gasses are released from the
flux as it melts with the filler metal, producing a shield. Flux produces slag which
must be chipped off after the weld is completed. There is no slag when shielding
gas such as argon is used. The gas is fed along with the wire through the gun.
While this method forms a cleaner weld, it may not always be convenient since
gas cylinders are required.

49 | P a g e
The process begins in all types when the wire or rod makes contact with the piece
to be welded. This completes an electric circuit and creates an arc through which
the transfer of the metal from the wire or rod to the piece is facilitated. Spatter
occurs during transfer; some of the molten drops of metal become airborne and
cover the piece and surrounding area with small globules that solidify on cooling.
Spatter may be minimized depending on the skill of the operator and the welding
method being used.
B. Typical Parts and Shapes That Can Be Welded
Nearly all metals of almost any thickness or shape can be welded. From sheet
metal to almost any thicker piece, closed containers to curved pieces. The shop
welding machines here at the UNB workshop have the capability to weld various
steels and aluminum.

2. Safety Considerations
A. Preparation and Set-up:
The immediate area should be well marked or sectioned off in the shop prior to
welding. This is necessary as others may be unaware the possible hazards of
welding.
The operator should wear protective clothing to include:
Boots – not sandals or open toed shoes;
Welding mask;
Safety glasses;
Jeans or heavy pants, not frayed or torn;
Welding apron and jacket are recommended; and Welding gloves.

50 | P a g e
B. Operation
Safety precautions during operation include:
Avoid breathing fumes, use the exhaust fan;
Do no weld in a confined space; and
Handle gas cylinders with care.
C. Clean Up
After operations, the shop should be cleaned. Electrode stubs should be disposed
of, any scrap metal should be placed in the scrap metal container, the floor should
be swept, and any water or other liquids spilled should be wiped up.
3. Safe Machine and Tool Operating Parameters
Always wear gloves, as there is a significant amount of UV radiation, enough to
burn skin. Spatter may also cause burns, not only on your skin but also inside
masks and clothing. This can be avoided by wearing a welding jacket and a full
welding mask. A welding mask is angled around the head of the operator so as to
maximize coverage from flying sparks.
4. Newer Developments and Improvements
An improved mask has been developed that will darken the lense automatically.
An electric circuit senses when the rod contacts the piece, and immediately
darkens the lense. This is a great improvement as the operator will no longer have
to continually switch from goggles to weld mask.
5. Environmental Concerns
A. Disposal and Recycling
Welding rods always leave one or two inches of stub, wire feed also leave some
scrap. Scraps and slag are a part of the normal process. These are usually placed
in scrap metal dumpsters and later sent to scrap yards for recycling.

51 | P a g e
B. Hazardous Fumes
Fans are required to remove hazardous vapours and gases. Toxicity levels depend
upon the chemical composition of fluxes and shield gasses. These gases also
contain particulate matter, so it is very important to weld only in a well ventilated
area. There is no difference in health between welders and non-welders when
operations are carried out in an area that is adequately ventilated.
6. Information for Design of Parts for Safe Machining
A. Preprocessing of Parts
Edges on pieces should be ground smooth and possibly machined to the correct
angle for the desired weld type. It is important to clean joining surfaces so that
they are free from anything that may weaken the weld. This includes oil, grease,
oxidation or dust.
B. Postprocessing of Parts
Parts should be cooled after the weld is completed, if possible. Slag and any
spatter should be chipped off with a chip hammer. Edges should have any rough
parts removed by grinding or filing.

EXPERIMENTAL MODEL

52 | P a g e
ADVANTAGES :

 Small in size.
 Cost is less compared to other welding machine.
 Due to portable ability it is easily handled.

DISADVANTAGES:

Not so effective for very hard materials.

Feed should be given intermittently.

Overload should be avoided.

APPLICATIONS:

There are many different uses of welding machines. Some of the areas where it
finds application are:

 Automobile industry
 Automotive manufacturing
 Metal working
 Shipbuilding
 Fabrication
 Casting

53 | P a g e
CONCLUSION

After completing the project, conclude that our project is simple in construction
and compact in size for use. Manufacturing of machine is easy and cost of the
machine is less.

54 | P a g e