Side Channel pumps

Self-priming, segmental type with very low NPSH

CEH 1201 ... 6108
CEH 1202/5 ... 6108/5
CEH 1202/7 ... 6107/7

Technical data

Capacity: from 0,4 up to 35 m³/h

Delivery head: from 10 up to 354 m
Speed: 1450 rpm (max. 1800 rpm)
Temperature: max. 120 °C
max. 180 °C for high temperature design
(higher temperatures upon request)
Casing pressure: PN 40
Shaft sealing: stuffing box or mechanical seal
Flange connections: DIN 2501 / PN 40
Direction of rotation: anti-clockwise,
(when seen from the drive end)

Application Construction
The Sterling SIHI CEH pump is a self-priming side channel Casing pressure
pump capable of handling gas along with the medium and
operates at a low noise level. Maximum 40 bar from -40 °C up to +120 °C.
The CEH pumps are used for problem-free pumping of clean Maximum 32 bar from +120 °C up to +180 °C.
liquids at unfavourable suction side conditions. They are also Pressure stages for temperature as per DIN EN 1333.
very suitable for positive suction heads below 0.5m
Please observe
The different material possibilities with uniform dimensions Technical rules and safety regulations:
and performance characteristics as well as the standard Casing pressure = inlet pressure + delivery head at minimum
exchangeable components, make the CEH particularly pump capacity.
recommendable for applications in the pharmaceutical,
chemical or petrochemical market as well as in the plastic or
oil industry. Because of its low NPSH and positive suction Position of branches
head the CEH is very suitable for the pumping of liquefied Axial suction branch, discharge branch points radially upwards
gasses and liquids under vapour pressure like condensate,
refrigerant, boiler feed water or LPG.
Flanges
The pumps of the CEH /7 series have a retaining stage to
avoid the dry running by controlling the liquid level in the pump. The flanges correspond to DIN EN 1092-2 / PN 40.
This design is especially developed for the handling of liquids Flange design as per DIN 2512 with groove or drilled according
under vapour pressure or when pumping from underground to ANSI 150 or 300 lbs is basically possible.
tanks. The series CEH /5 are used for bottom off-loading of
liquids under vapour pressure.
Bearing
Design One grease lubricated ball bearing according to DIN 625 and
one liquid surrounded sleeve bearing (design A). The ball
bearing is greased for life.
Pumps of the series CEH have a segmental type construction
with open vane wheel impellers. The construction of the CEH
pump is a so-called centrifugal combined system. Direction of rotation
This combination pump is suited with a centrifugal stage in
serial connection before the side channel stages to obtain a Anti-clockwise, when looking from the drive end.
more favourable NPSH.

The program comprises 6 sizes each with 1-8 stages. The Shaft sealing
existing material design allows an optimum rating for the The shaft can be sealed by a stuffing box or a mechanical
respectively desired performance range and the pumping seal conform DIN EN 12756.
medium. The shaft sealing is also available in a design suitable for
heating or cooling of the stuffing box or the mechanical seal.
Pumps of the series CEH /7 are equal to the CEH series but
equipped with a retaining stage. This program comprises 6 Double mechanical seal (back-to-back as well as tandem) or
sizes with 2-7 stages. The series CEH /5 have also 6 sizes a quench design with throttle bush are available upon request.
but with 2-8 stages. The CEH can also be supplied with a magnetic coupling (for
information see the separate catalogue).
The applied hydraulic components are from our Modular Side
Channel system (interchangeability of parts).

Sterling Fluid Systems Pumping Technology CEH-00 / 2002

Material design

Cast iron and Ductile iron

Pos. Components Material design
0A 0B 0F 1A 1B 1F
1060 Suction casing
1070 Discharge casing
1090 EN-GJL-250 EN-GJS-400-18-LT
1140
Intermediate piece
1141
1080
2100 Shaft X 20 Cr 13
2310 Impeller EN-GJL-250

2350 Vane wheel impeller CuZn40Al2 G-X 3 CrNiMoCuN 26 6 3 3 PAEK CuZn40Al2 G-X 3 CrNiMoCuN 26 6 3 3 PAEK

3500 Bearing housing EN-GJL-250

4410 Mechanical seal casing
EN-GJL-250 EN-GJS-400-18-LT
4510 Stuffing box casing
0241 Bearing bush CY 10 C / Carbon Antimony *

* Bearing bush in Carbon Antimony is used only in the high temperature design. This high temperature design is also provided
with cup springs and a cooled stuffing box or cooled mechanical seal.

Stainless steel

Pos. Components Material design

4B 4F
1060 Suction casing
1070 Discharge casing
1090 G-X CrNiMo 18 10
1140
Intermediate piece
1141
1080
2100 Shaft X 5 CrNiMo 17 12 2
2310 Impeller G-X 5 CrNiMoNb 18 10
2350 Vane wheel impeller G-X 3 CrNiMoCuN 26 6 3 3 PAEK
3500 Bearing housing EN-GJL-250 coated
4410 Mechanical seal casing G-X 6 CrNiMo 18 10
0241 Bearing bush CY 10 C

Casing seal General comments

The casing can be sealed with a liquid sealing compound Side Channel pumps with the same hydraulic construction are
or soft Teflon. manufactured in series as:

CEH With magnetic coupling

Drive
CEB Vertical tank mounted pump, PN 25 with magnetic
By electric motor, type of construction IM B3. coupling
For LPG, EExe or Eex d(e) motors are available. CEV Vertical tank mounted pump, PN 25
with mechanical seal (replacement of CVGP)
AEH High duty pump, PN 40
Also available with magnetic coupling
AKH Medium duty pump, PN 16
AOH Low duty pump with oval flanges, PN 10

Technical documents about these pump series will be readily

supplied on request.
Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 2 / 20
Sectional drawing and parts list (typical)

CEHA with stuffing box

1060 1090 1070 Pos. Components

2310 1140 4610 0241 Bearing bus h
1060 Suction cas ing
1070 Dis charge cas ing
1080 Interm ediate piece
1081 Retaining s tage
1090 Suction interm ediate piece
1140 Dis charge interm ediate piece
1141 Dis charge Interm ediate piece
2100 Shaft
2310 Im peller
2350 Vane wheel im peller
3500 Bearing hous ing
4330 Mechanical s eal
4410 Cas ing for m echanical s eal
4420 Cooling ins ert
1080 2350 4510 2100 4510 Cas ing for s tuffing box
0241 1141 3500 4610 Stuffing box

CEH with mechanical seal

Unbalanced as well as balanced mechanical seals are available.
4420
4410

Cooled stuffing box

4410

4330

Cooled mechnical seal

CEH /7 with retaining stage

1081

All possible design combinations can be found in the delivery program

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 3 / 20
Operating principle

The CEH pump or so-called centrifugal combined system (combination pump) is suited with a low NPSH centrifugal impeller
before the side channel stages (series connection). This NPSH inducer stage creates enough pressure to overcome the
entrance pressure loss of the first side channel stage or NPSH required.

A side channel stage consist of:

• a suction intermediate piece with the suction port,
• a discharge intermediate piece with the side channel, the air displacement channel at the end of the side channel, the
discharge port and the gas slot,
• a vane wheel impeller enclosed by the two intermediate pieces.

Vane wheel impeller

Discharge intermediate piece

Suction intermediate piece

Impeller

The turning of the vane wheel impeller creates an under pressure at the beginning of the side channel (centrifugal effect) and the
gas or liquid with gas is drawn in. The air displacement channel provokes a positive displacement effect so the gas remaining
at the root of the vane wheel impeller is forced out through the gas slot.
The pressure generating is obtained by the repetitive re-entering of the liquid in the side channel (corkscrew movement).

Corck screw movement of liquid

Side Channel
Gas

Discharge intermediate piece

Suction intermediate piece Air displacement channel

Gas slot Positive displacement effect

A side channel pump can de-aerate and degas the suction line by itself and is thus very suitable for suction lift operation. A side
channel pump can handle large quantities of (entrained) gas. Mixtures up to a gas share of 50% are possible. The ability for self-
priming and the handling of large amounts of (entrained) gas, will guarantee continuous operation even in case of evaporation
and therefore contribute to a higher level of safety in industrial processes.

To avoid cavitation the distance between the liquid level and the entrance at the suction side of the pump is restricted. This
distance is related to the NPSH or Net Positive Suction Head. The NPSH for CEH pumps is very low due to it special construction.
The axial entrance and its larger diameter results in a less disturbed flow and lower friction losses. Together with the low NPSH
of the centrifugal impeller the CEH can handle a positive suction head of less than 0.5 m.
This makes the CEH very suitable for pumping liquids near their boiling point at reasonable economic expenses and the low
NPSH guarantees also full output capacity because of operation without cavitation.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 4 / 20

Performance range

General conditions
Liquid: Water
Density: 1 kg/dm3
Viscosity: 1 cSt
Temperature: 20 °C
Atmospheric pressure: 1013 mbar

Characteristic tolerances
Capacity ± 5% - Delivery head ± 5% - Power + 10%
For designs with a mechanical seal or a casing seal of soft Teflon, the tolerance for the delivery head is extended by 2% each.

Measuring standard
According to ISO 5198

- - - - = maximum for CEH /7 (with retaining stage)

-..-..-.. = minimum for CEH /5 (e.g. LPG handling) , CEH /7
H
(m) n = 1450 rpm

300

200

1200 3100 3600 4100 5100 6100

100

0 0,4 1 2 4 6 8 10 20 Q 40
(m3/h)
NPSH
(m)
0,8 6100
0,6 5100
0,4 4100
3100 3600
0,2 1200

0 0,4 1 2 4 6 8 10 20 Q 40
(m3/h)

The NPSH curve is suitable for liquids without gas. When using a liquid containing gas (e.g. water 20 °C) a safety margin
of 1 m has to be added.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 5 / 20

Dimension chart, Pump set drawing and Performance curves

CEH 1200 and CEHA 1200/5

12 w
200 08 1450 rpm
12 a 171
07 25
H 12
06 4
(m)
120
5
120
100 4
1203
1202
G¼
1201 1)
44 41

0 m2 113
m1
3 v e1
12
08 f1
P 120
(kW) 7 w1
120
2 6
120 ∅14x4
5
1204 ∅105
∅75
1203 DN20
1 ∅14j5
1202
100 5
1201 1) ∅150
∅110
0 DN40
∅18x4
NPSH3) h3 176 10 100 16,1
(m)
0,6 d
0,4 35 13
0,2 105
0 140 c
0 1 2 Q 3 e2
(m3/h) b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt. * Dimensions depend upon the motor brand.
1)
Not for design CEH /5.
Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%. 2)
For EExe II T3 motors.
For designs with a mechanical seal or casing seal of soft Teflon, 3)
A safety margin of 1 m has to be added
the tolerance for the delivery head is extended by 2% each. when using a liquid containing gas.

Pump Motor Base Coupling Weight

size kW kW2) size plate B BDS2) pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
0.37 1) 71 P007 1) 39 317 350 285 110 135 609 570
1201 68 18 195 20 15 -9 238 204
0.55 80 P008 45 297 400 265 120 140 643 640
0.55 0.55 80 47
P008 297 20 15 400 265 120 140 677 640
1202 0.75 0.75 80 68 76 20 44 229 -9 272 238
1.1 1 90S P241 56 330 25 19 480 290 125 165 735 730
0.75 0.75 80 P210 52 300 420 260 115 711 650
1203 1.1 1 90S 68 76 22 58 263 25 19 -9 165 306 272
P241 330 480 290 125 769 730
1.5 1.35 90L 62
1.1 1 90S 60
P241 68 76 330 480 290 125 803 730
1204 1.5 1.35 90L 24 64 297 25 19 -9 165 340 306
2.2 2 100L P272 80 88 75 360 540 320 140 844 820
1.1 1 90S 66
68 76 837
1205 1.5 1.35 90L P272 26 70 331 360 25 19 540 320 140 -9 165 374 340 820
2.2 2 100L 80 88 77 878
1.5 1.35 90L P272 68 76 72 360 19 540 320 140 165 871 820
1206 2.2 2 100L 28 84 365 25 -9 408 374 912
P015 80 88 361 15 600 325 160 150 920
3 2.5 100L 85 912
1.5 1.35 90L 68 76 74 905
1207 2.2 2 100L P015 30 86 399 361 25 15 600 325 160 -9 150 442 408 920
80 88 946
3 2.5 100L 87
2.2 2 100L 88
1208 P015 80 88 32 433 361 25 15 600 325 160 -9 150 476 442 980 920
3 2.5 100L 89

The weight of the pump will be approximately 6% higher when using Stainless steel.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 6 / 20

Dimension chart, Pump set drawing and Performance curves

CEH 3100 and CEHA 3100/5

w
31 1450 rpm
300 08 201
a
31
07 40
H
(m) 310
6 4
310
200 5
310
4
3103
100 3102 G¼
3101 1)
50 42

m2 134
0 m1
P v e1
(kW) 310 f1
8
7 310 w1
7
6 310
6
310 ∅18x4
5 5 ∅140
4 3104 ∅100
3103 DN32
3 ∅19j5
3102 132
2 ∅185 6
31011) ∅145
1
DN65
0
NPSH3) h3 214 12 112 21,5
∅18x8
(m) d
35 13
0,2
135
0 170 c
1 2 3 4 Q 5 e2
(m3/h) b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt. * Dimensions depend upon the motor brand.
1)
Not for design CEH /5.
Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%. 2)
For EExe II T3 motors.
For designs with a mechanical seal or casing seal of soft Teflon, 3)
A safety margin of 1 m has to be added
the tolerance for the delivery head is extended by 2% each. when using a liquid containing gas.

Pump Motor Base Coupling Weight

size kW kW2) size plate B BDS2) pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
0.75 1) 80 P008 1) 60 297 20 15 400 265 120 152 691 640
3101 68 31 213 -13 261 227
1.1 90S P241 67 330 25 19 480 290 125 177 749 730
1.1 1 90S 72
P241 68 78 330 480 290 125 789 730
3102 1.5 1.35 90L 34 74 253 25 19 -13 177 301 267
2.2 2 100L P272 80 88 81 360 540 320 140 830 820
2.2 2 100L 89
3103 P272 80 88 38 293 360 25 19 540 320 140 -13 177 341 307 870 820
3 2.5 100L 90
2.2 2 100L 93
P272 360 19 540 320 140 177 910 820
3104 3 2.5 100L 80 88 42 94 333 25 -13 381 347
4 3.6 112M P015 117 361 15 600 325 160 162 931 920
3 2.5 100L 102 950
P015 80 88 600 160 162 920
3105 4 3.6 112M 45 120 373 361 25 15 325 -13 421 387 971
5.5 5 132S P017 95 103 158 700 200 192 1047 1100
4 3.6 112M P015 80 88 123 600 160 162 1011 920
3106 5.5 5 132S 48 161 413 361 25 15 325 -13 461 427 1087
P017 95 103 700 200 192 1100
7.5 6.8 132M 171 1113
4 3.6 112M 80 88 143 172 1051
3107 5.5 5 132S P017 52 165 453 361 25 15 700 325 200 -13 501 467 1127 1100
95 103 192
7.5 6.8 132M 205 1153
5.5 5 132S 198 1167
P017 361 25 15 700 325 200 192 1100
3108 7.5 6.8 132M 95 103 55 208 493 -13 541 507 1193
11 10 160M P436 253 540 30 24 840 490 215 240 1285 1270

The weight of the pump will be approximately 6% higher when using Stainless steel.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 7 / 20

Dimension chart, Pump set drawing and Performance curves

CEH 3600 and CEHA 3600/5

H w
(m) 36
08 1450 rpm
36 a 201
200 07 40
36 4
06
360
5
360
4
100 3603
3602 G¼
50 42
36011)
m2 134
0 m1
v e1
P
(kW) 36 f1
08
7 w1
36
07
6
360
6 ∅18x4
5 ∅140
360
5 ∅100
4 3604 DN32 ∅19j5
3 3603 132
∅185 6
2 3602 ∅145

1 36011) DN65

0 h3 214 12 112 21,5

∅18x8
NPSH3) d
(m)
35 13
0,5
135
0,2 170 c
e2
3 4 5 6 7
Q
8 b2
(m3/h)

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt. * Dimensions depend upon the motor brand.
1)
Not for design CEH /5.
Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%. 2)
For EExe II T3 motors.
For designs with a mechanical seal or casing seal of soft Teflon, 3)
A safety margin of 1 m has to be added
the tolerance for the delivery head is extended by 2% each. when using a liquid containing gas.

Pump Motor Base Coupling Weight

size kW kW2) size plate B BDS2) pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
0.75 80 P008 55 297 20 15 400 265 120 152 691 640
1) 1)
3601 1.1 90S 68 31 67 213 -13 261 227
P241 330 25 19 480 290 125 177 749 730
1.5 90L 74
1.5 1.35 90L P241 68 76 74 330 480 290 125 789 730
3602 34 253 25 19 -13 177 301 267
2.2 2 100L P272 80 88 89 360 540 320 140 830 820
2.2 2 100L 89
870
3603 3 2.5 100L P272 80 88 38 101 293 360 25 19 540 320 140 -13 177 341 307 820
4 3.6 112M 119 891
3 2.5 100L P272 105 360 19 540 320 140 177 910 820
80 88
3604 4 3.6 112M 42 117 333 25 -13 162 381 347 931
P015 361 15 600 325 160 920
5.5 5 132S 95 103 152 182 1007
3 2.5 100L 102 950
P015 80 88 600 160 162 920
3605 4 3.6 112M 45 120 373 361 25 15 325 -13 421 387 971
5.5 5 132S P017 95 103 171 700 200 192 1047 1100
4 3.6 112M P015 80 88 123 600 160 162 1011 920
3606 5.5 5 132S 48 161 413 361 25 15 325 -13 461 427 1087
P017 95 103 700 200 192 1100
7.5 6.8 132M 171 1113
5.5 5 132S 165 1127
3607 P017 95 103 52 453 361 25 15 700 325 200 -13 192 501 467 1100
7.5 6.8 132M 168 1153
5.5 5 132S 161 1167
P017 361 25 15 700 325 200 192 1100
3608 7.5 6.8 132M 95 103 55 171 493 -13 541 507 1193
11 10 160M P436 254 540 30 24 840 490 215 240 1285 1270

The weight of the pump will be approximately 6% higher when using Stainless steel.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 8 / 20

Dimension chart, Pump set drawing and Performance curves

CEH 4100 and CEHA 4100/5

H 41 w
(m) 08 1450 rpm
41 a 195
07
200 45
410
6 4
410
5
410
4
100 4103

4102 G¼
41011) 52 43

m2 140
0 m1
P v e1
410 f1
(kW) 8
12 410 w1
7
410
10 6 ∅18x4
410 ∅150
8 5
∅110
4104 DN40
∅24j5
6 4103 140 8
∅200
4 4102 ∅160
41011) DN80
2
h3 238 15 132 26,9
NPSH3) ∅18x8
(m) d
0,5 40 13
155
195 c
0 e2
6 7 8 9 10 11 12
Q
13 b2
(m3/h)

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt. * Dimensions depend upon the motor brand.
1)
Not for design CEH /5.
Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%. 2)
For EExe II T3 motors.
For designs with a mechanical seal or casing seal of soft Teflon, 3)
A safety margin of 1 m has to be added
the tolerance for the delivery head is extended by 2% each. when using a liquid containing gas.

Pump Motor Base Coupling Weight

size kW kW2) size plate B BDS2) pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
1.5 1) 90L P241 68 1) 81 330 480 290 125 798 730
4101 41 268 25 19 -23 197 294 260
2.2 100L P272 80 95 360 540 320 140 839 820
2.2 2 100L 98
894
4102 3 2.5 100L P272 80 88 47 110 323 360 25 19 540 320 140 -23 197 349 315 820
4 3.6 112M 128 915
4 3.6 112M P015 80 88 128 600 160 182 970 920
4103 53 378 361 25 15 325 -23 404 370
5.5 5 132S P017 95 103 179 700 200 192 1046 1100
5.5 5 132S 172 1101
4104 P017 95 103 59 433 361 25 15 700 325 200 -23 192 459 425 1100
7.5 6.8 132M 182 1127
5.5 5 132S 178 1156
P017 361 25 15 700 325 192 1100
4105 7.5 6.8 132M 95 103 65 181 488 200 -23 514 480 1182
11 10 160M P385 264 490 30 24 740 440 240 1274 1140
7.5 6.8 132M P385 196 490 740 440 200 212 1237 1140
4106 95 103 70 543 30 24 -23 569 535
11 10 160M P436 269 540 840 490 215 240 1329 1270
7.5 6.8 132M 202 212 1292
P436 95 103 540 30 24 840 490 215 1270
4107 11 10 160M 76 275 598 -23 240 624 590 1384
15 13.5 160L P487 110 118 349 610 35 28 940 550 240 260 1446 1420
11 10 160M 95 103 281 1439 1420
4108 P487 82 653 610 35 28 940 550 240 -23 260 679 645
15 13.5 160L 110 118 355 1501 1420

The weight of the pump will be approximately 6% higher when using Stainless steel.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 9 / 20

Dimension chart, Pump set drawing and Performance curves

CEH 5100 and CEHA 5100/5

510 w
300 8 1450 rpm
510 a 237
H 7
(m) 50
510
6 4
200 5105

5104
5103
100 5102 G¼
60 66
5101 1)
m2 159
0 m1
v e1
510 f1
30 8
P 510 w1
7
(kW)
5106
∅18x4
20 5105 ∅165
∅125
5104
DN50 ∅24j5
5103
165
10 ∅235 8
5102
∅190
51011)
DN100
h3 276 18 160 30,9
NPSH3) ∅22x8
(m) d
0,5 45 15
170
0 215 c
10 12 14 16 18 Q 20 e2
(m3/h) b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt. * Dimensions depend upon the motor brand.
1)
Not for design CEH /5.
Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%. 2)
For EExe II T3 motors.
For designs with a mechanical seal or casing seal of soft Teflon, 3)
A safety margin of 1 m has to be added
the tolerance for the delivery head is extended by 2% each. when using a liquid containing gas.

Pump Motor Base Coupling

size kW kW2) size plate B BDS2) pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
3 100L P272 123 360 19 540 320 140 225 918 820
1) 80 1)
5101 4 112M 60 162 305 25 -28 353 315 939
P015 361 15 600 325 160 210 920
5.5 132S 95 170 1015
5.5 5 132S 183 1090
P017 361 25 15 700 325 220 1100
5102 7.5 6.8 132M 95 103 70 193 380 200 -28 428 390 1116
11 10 160M P385 269 490 30 24 740 440 240 1208 1140
7.5 6.8 132M P017 196 361 25 15 700 325 220 1191 1100
95 103 200
5103 11 10 160M P385 80 279 455 490 740 440 -28 503 465 1283 1140
30 24 240
15 13.5 160L P436 110 118 353 540 840 490 215 1345 1270
11 10 160M 95 103 289 1358
5104 P436 90 530 540 30 24 840 490 215 -28 240 578 540 1270
15 13.5 160L 110 118 363 1420
15 13.5 160L 374 260 1495
110 118
5105 18.5 15 180M P487 101 395 605 610 35 28 940 550 240 -28 653 615 1420
280 1557
22 17.5 180L 125 135 415
15 13.5 160L P487 384 610 35 940 550 240 260 1570 1420
110 118
18.5 15 180M 423
5106 111 680 28 -28 280 728 690 1632
22 17.5 180L P538 425 660 35 1060 600 280 1620
125 135
30 24 200L 506 300 1690
18.5 15 180M 110 118 415
280 1707
5107 22 17.5 180L P538 121 435 755 660 35 28 1060 600 280 -28 803 765 1620
125 135
30 24 200L 516 300 1765
22 17.5 180L P538 446 660 35 1060 600 280 280 1782 1620
5108 125 135 132 830 28 -28 878 840
30 24 200L S389 527 540 40 1200 490 300 300 1840 1800

The weight of the pump will be approximately 6% higher when using Stainless steel.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 10 / 20

Dimension chart, Pump set drawing and Performance curves

CEH 6100 and CEHA 6100/5

H 61 w
(m) 08
1450 rpm
61 a 262
300 07
65
610
6 4
610
5
200
610
4
6103

100 6102 G3/8

64 63
6101 1)
m2 172
0 m1
v e1
P
(kW) 610 f1
8
50 6107 w1
6106
40
6105 ∅18x4
∅185
30 6104 ∅145
6103 DN65 ∅32j5
20
6102 180
∅235 10
10 61011) ∅190

0 DN100
NPSH3) h3 300 20 180 35,3
(m) ∅22x8
d
0,5 50 15
195
0 245
15 20 25 30 Q 35 c
e2
(m3/h) b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt. * Dimensions depend upon the motor brand.
1)
Not for design CEH /5.
Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%. 2)
For EExe II T3 motors.
For designs with a mechanical seal or casing seal of soft Teflon, 3)
A safety margin of 1 m has to be added
the tolerance for the delivery head is extended by 2% each. when using a liquid containing gas.

Pump Motor Base Coupling Weight

size kW kW2) size plate B BDS2) pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
5.5 1) 132S 1) 206 1073
6101 P017 95 80 338 361 25 15 700 325 200 -35 240 391 353 1100
7.5 132M 203 1099
11 10 160M P385 95 103 291 490 740 440 200 1281 1140
6102 92 428 30 24 -35 260 481 443
15 13.5 160L P436 110 118 365 540 840 490 215 1343 1270
18.5 15 180M 110 118 404
6103 P487 105 518 610 35 28 940 550 240 -35 280 571 533 1495 1420
22 17.5 180L 125 135 419
22 17.5 180L P487 431 610 940 550 240 280 1585 1420
6104 125 135 117 608 35 28 -35 661 623
30 24 200L P538 512 660 1060 600 280 300 1643 1620
30 24 200L 125 135 525 300 1733
6105 P538 130 698 660 35 28 1060 600 280 -35 751 713 1620
37 30 225S 140 152 594 325 1798
30 24 200L P538 125 135 537 660 35 1060 600 280 300 1823 1620
6106 37 30 225S 142 606 788 28 -35 841 803
S609 140 152 730 40 1200 670 310 325 1888 1820
45 36 225M 670
30 24 200L S389 125 135 550 540 490 300 300 1913 1800
6107 37 30 225S 155 619 878 40 28 1200 -35 931 893
S609 140 152 730 670 310 325 1978 1820
45 36 225M 683
37 30 225S 532 2003
14211 140 152 350 345 2000
6108 45 36 225M 167 630 968 740 40 28 1300 690 -35 1021 983 2080
55 44 250M 14212 160 - 701 400 370 2125 2100

The weight of the pump will be approximately 6% higher when using Stainless steel.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 11 / 20

Dimension chart, Pump set drawing and Performance curves

CEHA 1200/7 (with retaining stage)

w
200 1450 rpm
12 a 171
07
25
H 12 G½
06 4
(m)
120
5
120
100 4
1203
1202
G¼
44 41
0
m2 113
m1
3 v e1
12 f1
P 07
(kW) 120 w1
6
2 120
5 ∅14x4
1204 ∅105
∅75
1203
DN20
1202 ∅14j5
1 100
∅150 5
∅110

0 DN40
∅18x4
h3 176 10 100 16,1
NPSH1)
(m) d
0,4 35 13
0,2 105
0 140
0 c
1 2 Q 3 e2
(m3/h) b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt.

Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%.
For designs with a mechanical seal or casing seal of soft Teflon, the tolerance for the delivery head is extended
by 2% each.

Pump Motor Base Coupling Weight

size kW size plate pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
0.55 80 52
1202/7 P210 BDS76 22 263 300 25 19 420 260 115 -9 165 306 272 709 650
0.75 80 53
0.75 80 54 743
1203/7 P241 BDS76 24 297 330 25 19 480 290 125 -9 165 340 306 730
1.1 90S 64 796
1.1 90S 70
1204/7 P272 BDS76 26 331 360 25 19 540 320 140 -9 165 374 340 830 820
1.5 90L 71
1.5 90L P272 BDS76 73 360 19 540 320 140 165 864
1205/7 28 365 25 -9 408 374 820
2 100L P015 BDS88 84 361 15 600 325 160 150 922
1.5 90L BDS76 69 898
1206/7 P015 30 399 361 25 15 600 325 160 -9 150 442 408 920
2 100L BDS88 86 956
1.5 90L BDS76 71 932
1207/7 P015 32 433 361 25 15 600 325 160 -9 150 476 442 920
2 100L BDS88 91 990

1)
A safety margin of 1 m has to be added when using a liquid containing gas.
* Dimensions depend upon the motor brand.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 12 / 20

Dimension chart, Pump set drawing and Performance curves

CEHA 3100/7 (with retaining stage)

w
31 1450 rpm
300 07 a 201
H 310 40
(m) 6 G½
310 4
5
200 310
4
3103
3102
100
G¼
50 42
0
m2 134
m1
P
(kW) 31 v e1
07
f1
6 31
06 w1
5 310
5
3104 ∅18x4
4
∅140
3103 ∅100
3 DN32
3102 ∅19j5
2 132
∅185 6
1 ∅145

0 DN65
∅18x8 12 112 21,5
h3 214
NPSH1)
(m) d
35 13
0,2
135
0 170
1 2 3 4 5 c
Q e2
(m3/h) b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt.

Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%.
For designs with a mechanical seal or casing seal of soft Teflon, the tolerance for the delivery head is extended
by 2% each.

Pump Motor Base Coupl. Weight

size kW size plate pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
1.5 90L BDS76 87 822
3102/7 P272 38 293 360 25 19 540 320 140 -13 177 341 307 820
2 100L BDS88 100 880
2 100L 104
3103/7 P272 BDS88 42 333 360 25 19 540 320 140 -13 177 381 347 920 820
2.5 100L 106
2.5 100L 101 960
3104/7 P015 BDS88 45 373 361 25 15 600 325 160 -13 162 421 387 920
3.6 112M 107 966
2.5 100L 107 1000
3105/7 P015 BDS88 48 413 361 25 15 600 325 160 -13 162 461 427 920
3.6 112M 110 1006
3.6 112M BDS88 117 172 1046
3106/7 P017 52 453 361 25 15 700 325 200 -13 501 467 1100
5 132S BDS103 151 192 1142
3.6 112M BDS88 120 172 1086
3107/7 P017 55 493 361 25 15 700 325 200 -13 541 507 1100
5 132S BDS103 154 192 1182

1)
A safety margin of 1 m has to be added when using a liquid containing gas.
* Dimensions depend upon the motor brand.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 13 / 20

Dimension chart, Pump set drawing and Performance curves

CEHA 3600/7 (with retaining stage)

H w
(m) 1450 rpm
200 36 a 237
07
50
36 G½
06
4
360
5
360
4
100 3603
3602
G¼
50 42
0 m2 134
P m1
(kW) v e1
7 36 f1
07
6 360 w1
6
5 360
5 ∅18x4
4 3604 ∅140
∅100
3603 DN32
3
∅19j5
3602 132
2 ∅185 6
∅145
1
DN65
NPSH 1)
∅18x8 12 112 21,5
h3 214
(m)
0,5 d
35 13

0 135
3 4 5 6 7
Q
8 170 c
e2
(m3/h)
b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt.

Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%.
For designs with a mechanical seal or casing seal of soft Teflon, the tolerance for the delivery head is extended
by 2% each.

Pump Motor Base Coupl. Weight

size kW size plate pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
1.5 90L BDS76 87 822
3602/7 P272 38 293 360 25 19 540 320 140 -13 177 341 307 820
2 100L BDS88 100 880
2 100L 104
3603/7 P272 BDS88 42 333 360 25 19 540 320 140 -13 177 381 347 920 820
2.5 100L 106
2.5 100L 101 960
3604/7 P015 BDS88 45 373 361 25 15 600 325 160 -13 162 421 387 920
3.6 112M 107 966
2.5 100L 107 1000
3605/7 P015 BDS88 48 413 361 25 15 600 325 160 -13 162 461 427 920
3.6 112M 110 1006
3.6 112M BDS88 117 172 1046
3606/7 P017 52 453 361 25 15 700 325 200 -13 501 467 1100
5 132S BDS103 151 192 1142
3.6 112M BDS88 120 172 1086
3607/7 P017 55 493 361 25 15 700 325 200 -13 541 507 1100
5 132S BDS103 154 192 1182

1)
A safety margin of 1 m has to be added when using a liquid containing gas.
* Dimensions depend upon the motor brand.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 14 / 20

Dimension chart, Pump set drawing and Performance curves

CEHA 4100/7 (with retaining stage)

H w
(m) 1450 rpm
41 a 195
07
200 410 45
6 G½
410 4
5
410
4
100 4103

4102
G¼
52 43
0 m2 140
m1
P v e1
12 410
7 f1
(kW)
410 w1
10 6
410
5
8 ∅18x4
4104
∅150
∅110
6 4103 DN40
∅24j5
4102 140
4 ∅200 8
∅160
2
DN80
NPSH1) ∅18x8 15 132 26,9
h3 238
(m)
d
0,5
40 13

0 155
6 7 8 9 10 11 12 Q 13 195 c
e2
(m3/h)
b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt.

Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%.
For designs with a mechanical seal or casing seal of soft Teflon, the tolerance for the delivery head is extended
by 2% each.

Pump Motor Base Coupl. Weight

size kW size plate pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
2.5 100L 112 959
4102/7 P015 BDS88 53 378 361 25 15 600 325 160 -23 182 404 370 920
3.6 112M 115 965
3.6 112M P015 BDS88 121 600 160 182 1020 920
4103/7 59 433 361 25 15 325 -23 459 425
5 132S P017 BDS103 158 700 200 192 1116 1100
3.6 112M BDS88 130 1075
4104/7 P017 65 488 361 25 15 700 325 200 -23 192 514 480 1100
5 132S BDS103 164 1171
5 132S 172 1226
4105/7 P385 BDS103 70 543 490 30 24 740 440 200 -23 212 569 535 1140
6.8 132M 232 1237
6.8 132M 248 212 1292
4106/7 P436 BDS103 76 598 540 30 24 840 490 215 -23 624 590 1270
10 160M 278 240 1379
6.8 132M P436 230 653 540 30 24 840 490 215 212 1347 1270
4107/7 BDS103 82 -23 679 645
10 160M P487 296 653 610 35 28 940 550 240 260 1434 1420

1)
A safety margin of 1 m has to be added when using a liquid containing gas.
* Dimensions depend upon the motor brand.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 15 / 20

Dimension chart, Pump set drawing and Performance curves

CEHA 5100/7 (with retaining stage)

w
300 510 1450 rpm
7
a 237
H 510
6 50
(m) G½
5105 4
200
5104
5103

5102
100
G¼
60 66
0
m2 159
30 m1
510 v e1
P 7
f1
(kW) 5106
w1
20 5105

5104 ∅18x4
∅165
5103 ∅125
DN50
10 ∅24j5
5102
165 8
∅235
∅190

DN100
NPSH1) ∅22x8 18
h3 276 160 30,9
(m)
0,5 d
45 15
0 170
10 12 14 16 18 20
Q 195 c
(m3/h) 215
b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt.

Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%.
For designs with a mechanical seal or casing seal of soft Teflon, the tolerance for the delivery head is extended
by 2% each.

Pump Motor Base Coupl. Weight

size kW size plate pump set a b2 c d e1 e2 v f1 h3 m1 m2 w* w1
5 132S 180 1180
5102/7 P017 BDS103 80 455 361 25 15 700 325 200 -28 220 503 465 1100
6.8 132M 232 1191
6.8 132M P385 252 490 740 440 200 1266 1140
5103/7 BDS103 90 530 30 24 -28 240 578 540
10 160M P436 292 540 840 490 215 1353 1270
10 160M 325 1428
5104/7 P487 BDS103 101 605 610 35 28 940 550 240 -28 260 653 615 1420
13.5 160L 347 1472
10 160M BDS103 335 1503
P487 610 940 550 240 260 1420
5105/7 13.5 160L 111 357 680 35 28 -28 728 690 1547
BDS118
15 180M P538 395 660 1060 600 280 280 1640 1620
13.5 160L 408 260 1622
5106/7 P538 BDS118 121 755 660 35 28 1060 600 280 -28 803 765 1620
15 180M 429 280 1715
15 180M 440
5107/7 P538 BDS118 132 830 660 35 28 1060 600 280 -28 280 878 840 1790 1620
17.5 180L 463

1)
A safety margin of 1 m has to be added when using a liquid containing gas.
* Dimensions depend upon the motor brand.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 16 / 20

Dimension chart, Pump set drawing and Performance curves

CEHA 6100/7 (with retaining stage)

H w
(m) 61
07 1450 rpm
300 a 262
610
6 65
G½
610
5
200 610
4
6103

100 6102

G3/8
64 63
0
m2 172
P
(kW) m1
50 610 v e1
7
f1
610
40 6 w1
6105
30 6104
∅18x4
∅185
6103 ∅145
20
6102 DN65
∅32j5
10 180
∅235 10
∅190
0
DN100
NPSH1) ∅22x8 180 35,3
(m) h3 300 20

0,5 d
50 15
0
15 20 25 30 35 195
Q 245 c
(m3/h) e2
b2

General: Values are valid for water ρ = 1 kg/dm3 and ν = 1 cSt.

Design tolerances: Capacity ± 5% - Delivery head ± 5% - Power + 10%.
For designs with a mechanical seal or casing seal of soft Teflon, the tolerance for the delivery head is extended
by 2% each.

Pump Motor Base Coupl. Weight

size kW size plate pump set a
b2 c d e1 e2 v f1 h3 m1 m2 w* w1
6.8 132M P385 267 490 740 440 200 1279 1140
6102/7 BDS103 105 518 30 24 -35 260 571 533
10 160M P436 307 540 840 490 215 1366 1270
10 160M BDS103 331 1456
6103/7 13.5 160L P487 117 363 608 610 35 28 940 550 240 -35 280 661 623 1500 1420
BDS118
15 180M 384 1593
15 180M 439
BDS118 280 1683
6104/7 17.5 180L P538 130 461 698 660 35 28 1060 600 280 -35 751 713 1620
24 200L BDS135 540 300 1738
15 180M 450
BDS118 280 1773
6105/7 17.5 180L P538 142 473 788 660 35 28 1060 600 280 -35 841 803 1620
24 200L BDS135 485 300 1828
17.5 180L BDS118 391 280 1863
S389 540 490 300 1800
6106/7 24 200L BDS135 155 470 878 40 28 1200 -35 300 931 893 1918
30 225S S609 BDS152 620 730 670 310 325 2018 1820
24 200L S389 BDS135 482 540 40 28 1200 490 300 300 2008 1800
6107/7 30 225S 14211 167 532 968 -35 1021 983 2003
BDS152 740 40 28 1300 609 350 345 2000
36 225M 14211 630 2080

1)
A safety margin of 1 m has to be added when using a liquid containing gas.
* Dimensions depend upon the motor brand.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 17 / 20

Notes

It is the policy of Sterling Fluid Systems to seek continually for ways to improve its products
and the right is reserved to alter specifications at anytime without prior notice.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 18 / 20

Sterling SIHI Side Channel pumps

Sterling Fluid Systems offers an extensive Side Channel pump range under its brand name Sterling
SIHI. Sterling Fluid Systems has more than 80 years of experience in manufacturing, installation and
support of Side Channel pumps. The Sterling SIHI Side Channel pumps can be found in a wide
application range for the:
• Chemical market
• Pharmaceutical industry
• Petrochemical industry
• Food industry
• Ship yards
• LPG industry
• and many more ...

The Sterling SIHI Side Channel pump range

1000

CEH
AEH
AEHL
ADHL
100 CDHL
Delivery head (m)

AOH ASH

AKH

10 AKL
AKV

AOL
DRV

0 10 20 30 40
Capacity (m3/h)

The benefits of the Sterling SIHI Side Channel pumps

• Self priming
• Gas handling
• High-resistant materials
• Performance curve characteristics
• High efficiency
• Low NPSHR value
• Modular hydraulic system

The Sterling SIHI Side Channel pumps comply with the highest demands of our customers and
are the best solution for the handling of liquids under critical physical conditions.

Sterling Fluid Systems Pumping Technology CEH-00 / 2002 Page 19 / 20

 Sterling Fluid Systems (Europe) www .sterlingfluidsystems.com/europe
www.sterlingfluidsystems.com/europe

Sterling Fluid Systems (Austria) Sterling Fluid Systems (Belgium) Sterling Fluid Systems (Czech R epublic)
Republic)
A-1100 Wien, Zone Gosset, t Hofveld 1, Kosmonautu 8,
Oberlaaer Strasse 228, Austria. B-1702 Groot-Bijgaarden, Belgium. CZ-77211 Olomouc, Czech Republic.
Telephone : +43 (0)1 680 050 Telephone : +32 (0)2 481 7711 Telephone : +420 (0)68 551 66 51
Fax : +43 (0)1 680 0521 Fax : +32 (0)2 481 7737 Fax : +420 (0)68 551 66 53

Sterling Fluid Systems (France) Sterling Fluid Systems (Germany) Sterling Fluid Systems (Germany)
Zone Industrielle de Trappes-Elancourt, Lindenstrasse 170 Halbergstrasse 1
1-3, Avenue Georges Politzer B.P. 41, D-25524 Itzehoe/Holstein, Germany. 67061 Ludwigshafen, Germany.
78193 Trappes Cedex, France. Telephone : +49 (0)4821 77101 Telephone : +49 (0)621 56 12 0
Telephone : +33 (0)1 34 82 39 00 Fax : +49 (0)4821 771213 Fax : +49 (0)621 56 12 205
Fax : +33 (0)1 34 82 39 61

Sterling Fluid Systems (Hellas) Sterling Fluid Systems (Hungary) Sterling Fluid Systems (Italy)
4, Clisouras Street, Radnóti Ter 2/A, Via Pompei, 15
GR-176 72 Kallithea, Athens, Greece. H-8200 Veszprém, Hungary. I-20052 Monza,Italy.
Telephone : +30 (0)1 9570783 Telephone : +38 (0)88 40 63 33 Telephone : +39 (0)39 2824 1
Fax : +30 (0)1 9568121 Fax : +38 (0)88 40 66 35 Fax : +39 (0)39 2824 2 20

Sterling Fluid Systems (Netherlands) Sterling Fluid Systems (Polska) Sterling Fluid Systems (R omania)
(Romania)
Havenstraat 22-28, Postbus 27 UI, Chocimska 28 Mihai Eminescu 105 - 107,
NL 1940 AA Beverwijk, PL-00-791, Warzawa RO-72112, Bucarest 2.
The Netherlands. Telephone : +48 (0) 22 849 7097 Telephone : +40 (0) 1 610 7188
Telephone : +31 (0)251 263 232 Fax : +48 (0) 22 849 6726 Fax : +40 (0) 1 210 8287
Fax : +31 (0)251 226 309

Sterling Fluid Systems (Schweiz) Sterling Fluid Systems (Spain) Sterling SA

SATT (Germany)
Schweizersbildstrasse 25, Vereda de los Zapateros s/n Kaddenbusch 21,
P O Box 110, Apartado de Correos 57038 25578 Dägeling / Holstein, Germany.
8205 Schaffhausen, Switzerland. 28223 Pozuelo de Alarcón (Madrid), Telephone : +49 (0)4821 9000-0
Telephone : +41 (0)52 6440606 Spain. Fax : +49 (0)4821 9000-501
Fax : +41 (0)52 6440616 Telephone : +34 (0)91 709 1310
Fax : +34 (0)91 715 97 00
Sterling Fluid Systems (UK) Sterling Fluid Systems (UK)
Atlantic Street Industrial Estate, Atlantic Theale Cross, Pincents Lane
street Calcot, Reading,
Altricham, Cheschire, England WA14 Berkshire RG31 7SP, UK.
5DH Telephone : +44 (0)118 932 3123
Telephone : +44 (0)161 928 6371 Fax : +44 (0)118 932 3302
Fax : +44 (0)161 925 2129

Sterling Berkefeld (Germany)

Berkefeld Sterling Berkefeld (Netherlands)
Berkefeld Sterling RWO (Germany)
Lückenweg 5 Cairostraat 55, NL-3004 Learkaempe,
29227 Celle, Germany. AC Rotterdam, 28259 Bremen, Germany
Telephone : +49 (0) 5141 8030 Telephone : +31 (0)10 2622525 Telephone : +49 (0) 421 537050
Fax : +49 (0) 5141 803172 Fax : +31 (0)10 2622822 Fax : +49 (0) 421 5370540

Sterling Fluid Systems (Americas) www .sterlingfluidsystems.com/americas

www.sterlingfluidsystems.com/americas

Sterling Fluid Systems (USA) Sterling Fluid Systems (Canada) Sterling Fluid Systems (USA)
303 Industrial Boulevard, 225 Speedvale Avenue West, 2005 Dr M. L. King Jr. Street,
P O Box 460, P O Box 728. P O Box 7026,
Grand Island, NY 14072-0460, USA. Guelph, Ontario N1H 6L8, Canada. Indianapolis, IN 46207-7026, USA.
Telephone : (1) 716 773 6450 Telephone : (1) 519 824 4600 Telephone : (1) 317 925 9661
Fax : (1)716 773 2330 Fax : (1) 519 824 7250 Fax : (1) 317 924 7388

Sterling PCU Sterling Fluid Systems (Me xico)

(Mexico) Sterling Berkefeld (Canada)
2280 West Dorothy Lane Av. Milimex No. 115, Franco Industrias 225 Speedvale Avenue West,
Dayton 45439-1892 Ohio, USA. Milimex P O Box 728.
Telephone : (1) 937 299 5594 Carr. Miguel Aleman Km. 16.5 Guelph, Ontario N1H 6L8, Canada.
Fax : (1) 937 299 3843 Apodaca, Nuevo Leon Mexico CP666000 Telephone : (1) 519 824 4600
Mexico Fax : (1) 519 824 7250
Telephone : (52) 83 693 644
Fax : (52) 83 693 649
Sterling Fluid Systems (Asia) www .sterlingfluidsystems.com/asia
www.sterlingfluidsystems.com/asia

Sterling Fluid Systems (Asia) SIHI (Australia) Sterling Fluid Systems (China)
37 Tech Park Crescent, 820 Mountain Highway, Room 6016, 6th Floor, Central Place
Tuas South Avenue 4, Bayswater, Victoria 3153, No 16 Henan Road South,
Singapore 637851. Australia. Shangai 200002, China
Telephone : (65) 8630 828 Telephone : (61) 3 9720 1500 Telephone : (8621) 63363488 /(8621) 63740220
Fax : (65) 8630 868 Fax : (61) 3 9720 4076 Fax : (8621) 63268487

Sterling Fluid Systems (Malaysia) Sterling Fluid Systems (Philippines) Sterling Fluid Systems (Thailand)
No. 2, Jalan TPK 2/2, Taman Suite 404 & 405, Alabang Corporate 1st Floor, Solid Group Building,
Perindustrian Centre, 104 Thavorn, Patanakarn Road,
Kinrara, Section 2, 47100 Puchong, Km. 25 West Service Road, Suan-Luang,
Selangor Darul Ehsan, Malaysia. South Superhighway, Bangkok 10250, Thailand.
Telephone : (60) 3 5700198/99 Muntinlupa City, Philippines. Telephone : (66) 2 321 8422/3
Fax : (60) 3 5700204 Telephone : (63) 2 807 2076 Fax : (66) 2 321 8413
Fax : (63) 2 807 2013

Sterling Fluid Systems (Middle East/Africa) www .sterlingfluidsystems.com/middle - east

www.sterlingfluidsystems.com/middle www .sterlingfluidsystems.com/africa
www.sterlingfluidsystems.com/africa

Sterling Fluid Systems (Middle East) Sterling Berk efeld (Middle East)
Berkefeld Sterling Fluid Systems (South Africa)
P O Box 61491, Jebel Ali, Dubai U.A.E. P O Box 71421, Dubai U.A.E. 8483 Edleen, 1625 Johannesburg, R.S.A.
Telephone : +971 (0)4 8838 733 Telephone : +971 (0)4 3323 773 Téléphone : (27) 11 394 3922
Fax : +971 (0)4 8838 735 Fax : +971 (0)4 3323 737 Fax : (27) 11 970 2472

www.sterlingfluidsystems.com