Asme B16.3

--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
COPYRIGHT 2003; American Society of Mechanical Engineers Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
02/03/2003 21:22:05 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
S T D - A S M E BLb-3-ENGL L998 I0759b70 Ob12703 239 m
The American Society of

Mechanical Engineers
A N
A M E R I C A N
N A T I O N A L
S T A N D A R D
MALLEABLE RI ON
THREADED FITTINGS
Classes 150 and 300
ASME B16.3-1NU8
(Revision of ASME B16.3-1992)
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
Date of Issuance: July 19, 1999
The 1998 edition of this Standard is being issued with an automatic addenda
subscription service. The use of addenda allows revisions made in response
to public review comments or committee actions to be published on a regular
yearly basis; revisions published in addenda will become effective 6 months
after the Date of Issuance of the addenda. The next edition of this Standard
is scheduled for publication in 2003.
ASME issues written replies to inquiries concerning interpretations of

technical aspects of this Standard. The interpretations will be included with
the above addenda service.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
ASME is the registered trademark of The American Society of Mechanical Engineers.
This code or standard was developed under procedures accredited as meeting the criteria for
American National Standards. The Standards Committee that approved the code or standard
was balanced to assure that individuals from competent and concerned interests have had an
opportunity to participate. The proposed code or standard was made available for public review
and comment that provides an opportunity for additional public input from industry, academia,
regulatory agencies, and the public-at-large.
ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device,
or activity.
ASME does not take any position with respectto the validity of any patent rights asserted in
connection with any items mentioned in this document, and does not undertake to insure anyone
utilizing a standard against liabilityfor infringement of any applicablePatent, Letters
nor assumes
any such liability. Users of a code or standard are expressly advised that determination of the
validity of any such patent rights, and the risk of infringement of such rights, is entirely their
own responsibility.
Participation by federal agency representativek) or person(s) affiliated with industry is not to
be interpreted as government or industry endorsement of this code or standard.
ASME acceptsresponsibilityforonlythose interpretations issuedi n accordance with governing
ASME procedures and policies which precludes the issuance of interpretations by individual
volunteers.
No part of this document may be reproduced in any form,

i n an electronic retrieval system or otherwise,
without the prior written permission of the publisher.
The American Society of Mechanical Engineers

Three Park Avenue, New York, NY 10016-5990
Copyright O 1999 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved
Printed in U.S.A.
FOREWORD
In 1921, theAmerican EngineeringStandardsCommittee, later the AmericanStandards

Association (ASA) and currently the American National Standards Institute (ANSI), authorized
the organization of a Sectional Committee onthe Standardization of Pipe Flanges and
Flanged Fittings, withthe followingorganizations as jointsponsors:Heating, Piping, and
Air Conditioning Contractors National Association (later the Mechanical Contractors Associa-
tion of America, MCAA), Manufacturers Standardization Society of the Valves and Fittings
Industry (MSS), and The American Society of MechanicalEngineers(ASME).
Threaded fittings were also included in the scope of the B 16 Committee, and Subcommittee
Number 2 (nowSubcommittee B) wasmade responsible for threaded fittings other than
steel. The first edition of a standard covering malleable iron fittings, 150 lb,was approved
as American TentativeStandard by ASAin December1927. In 1936,a revision was
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
undertakento addhydraulic service ratings, material specifications, alignment tolerances,
and dimensions for additional sizes. It was approved with the designation American Standard
B 1 6 ~1939.
-
Pipe plugs, bushings, and locknuts, included in thefirst editions, are now covered in a
separate standard, B 16.14.
A revisionbegun in 1947 amplified the sections on threading, inspection, and tolerances,
and added dimensions for additional sizes of elbows, reducing crosses, reducing tees, straight
and reducingcouplings, caps, and return bends. Itwas approved as ASA B16.3-195 1.
Meanwhile, MSS, in cooperation withthe Association of AmericanRailroads(AAR),
developed the first standard for 300 lb malleable iron threaded fittings, published as MSS
SP-31 of 1932. The 1950 edition of SP-31, which agreed withAAR Purchase Specification
M-404, was submitted toASA SectionalCommittee BI6 and assigned to Subcommittee
Number 2. After balloting, it was approved as aseparated standard, ASA B16.19-1951.
Work wasbegunto combine thetwo standards (for 150 lband 300 lb) into a single
document in 1961.The resulting Standard was approved asASA B16.3-1963.Subsequent
reviews ofthe Standard,leading to revisions approved as ANSI B16.3-1971 andANSI
B16.3-1977, involved updating of referencedstandards and the introduction of metric (SI)
dimensions and ratings. Inthe1977 edition, 150 lb and 300 lb were redesignated as Class
150 and Class300.
In 1982, American National Standards Committee B16 became the ASME B16 Standards
Committee,operating withthe samescopeunderASMEproceduresaccredited by ANSI.
A further revision of the standard, approvedandpublished as ANSVASME B16.3-1985,
provided for electrodeposition asan alternative to hot dipping when zinccoating was
required.
The 1992 edition of B 16.3 omitsmetric units, establishing U.S. customary units as the
standard. Clarifications and editorial revisions were made in order to improve the text.
Followingapproval by the StandardsCommittee and ASME, the 1992 edition received
approval as anAmericanNational StandardonDecember 2, 1992, with the designation
ASME B16.3-1992.
In the1998 edition of ASME B16.3, the References section hasbeen updated, a Quality
SystemProgram Annexhasbeen added, and several editorial revisions have been made.
...
III
Following approvalby ASME B16Subcommittee B and B16 Main Committee, ANSI
approved thisAmericanNational Standard on November 20, 1998.
Requests for interpretation and suggestions for revision should be sent tothe Secretary,
B16 Committee, The American Society of Mechanical Engineers, Three Park Avenue, New
York. NY 10016-5990.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E B L b - 3 - E N G L L778 m 0757670 Ob12707 78q 9
ASME B16 COMMllTEE

Standardization of Valves, Flanges, Fittings, Gaskets,
and Valve Actuators
of this Standard.)
(The following is the roster of the Committee at the time of approval
OFFICERS
W. N. McLean, Chair
H. R. Sonderegger, Vice Chair
P. A. Reddington, Secretary
COMMITTEE PERSONNEL
W. L. Ballis, Consultant, London, Ohio
R. W. Barnes, Anric Enterprises, Etobicoke, Ontario, Canada
R. R. Brodin, Fisher Controls International, Inc., Marshalltown, Iowa
M . A. Clark, Nibco, Inc., Elkhart, Indiana
A. Cohen, A. Cohen and Associates, Albuquerque, New Mexico
C. E. Floren, Mueller Co., Decatur, Illinois
D. R. Frikken, Solutia, Inc., St. Louis, Missouri
R. Henrich, Minnegasco, Inc., Golden Valley, Minnesota
J. C. Inch, Mueller Refrigeration Products Co., Hartsville, Tennessee
G. A. Jolly, Vogt Valve Co., Louisville, Kentucky
W. G. Knecht, BW/IP International, Inc., Williamsport, Pennsylvania
R. Koester, The William Powell Co., Cincinnati, Ohio
W. N. McLean, Newco Valves, Palos Park, Illinois
M . L. Nayyar, Bechtel Power Corp.. Gaithersburg, Maryland
P. A. Reddington, American Society of Mechanical Engineers, New York, New York
R. A. Schmidt, Trinity-Ladish Co., Russellville, Arkansas
H. R. Sonderegger, Grinnell Corp., Cranston, Rhode Island
W. M. Stephan, Flexitallic, Inc., Mount Laurel, New Jersey
T. F. Stroud, Ductile Iron Pipe Research Association, Birmingham, Alabama
M.D. Wasicek, ABS Americas, Houston, Texas
R. E. White, Richard E. White and Associates, South Bend, Indiana
D. A. Williams, Southern Company Services, Birmingham, Alabama
L. A. Willis, The Dow Chemical Co., Freeport, Texas
W. R. Worley, Union Carbide Corp., South Charleston, West Virginia
SUBCOMMITTEE B - THREADED FITTINGS (EXCEPT STEEL)

H. R. Sonderegger, Chair, Grinnell Corp., Cranston, Rhode Island
B. P. Feder, Secretary, American Society of Mechanical Engineers, New York, New York
K. Barron, Ward Manufacturing, Blossburg, Pennsylvania
M . A. Clark, Nibco, Inc., Elkhart, Indiana
A. Cohen, A. Cohen and Associates, Albuquerque, New Mexico
A. A. Knapp, Canadian Copper/Brass Development Association, North York, Ontario, Canada
R. L. Larkin, American Darling Valve, Birmingham, Alabama
P. 1. McGrath, Jr., Consultant, Birmingham, Alabama
W. N. McLean, Newco Valves, Palos Park, Illinois
J. K. Schultz, Conine Manufacturing Co., Inc., Tyler, Texas
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D = A S M E BLb.3-ENGL L998 I0759b70 ObL2708 A L O m
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
CONTENTS
...
Foreword ....................................................................................... 111
Standards
Committee
Roster ...................................................................... v
1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
2 Pressure-Temperature
Ratings ......................................................... 1
3 Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 Dimensions and Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
7 Threading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
8 Ribs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
9 Plugs,
Bushings, and Locknuts .......................................................... 3
10 Face
Bevel ............................................................................... 3
11 Coatings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figures
1 Identification of Reducing Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Gaging
2 of Chamfered Internal Threads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tables
1 Pressure-TemperatureRatings .............................................................. 2
2 Inspection
Tolerances ...................................................................... 3
3 Dimensions of Class 150. 90deg Elbows. Tees.andCrosses. and 45 degElbows
(Straight Sizes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4Dimensions of Class 150. 90 deg Elbows and Crosses(ReducingSizes) ..................... 5
5 Dimensions of Class 150 Tees (Reducing Sizes) ............................................ 6
Dimensions
6 of Class 150. 45 deg Y-Branches (Straight Sizes) ............................... 7
7 Dimensions of Class 150 Street Tees and 90 deg and 45deg Street Elbows . . . . . . . . . . . . . . . . . 8
8 Dimensions of Class 150 Couplings (Straight and Reducing Sizes) ........................... 9
9 Dimensions of Class 150 Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
I O Dimensions of Class 150. Closed-. Medium-. and Open-Pattern Return Bends . . . . . . . . . . . . . . . . 11
1 1 Dimensions of Class300. 90 degElbows. Tees. and Crosses. and 45degElbows
(Straight Sizes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
12 Center-to-EndDimensions of Class 300. 90 degElbows(Reducing Sizes) .................... 13
13 Center-to-End Dimensions of Class 300 Tees (Reducing Sizes) .............................. 13
14 Dimensions of Class 300Couplings ........................................................ 14
15 Dimensions of Class 300Reducing Couplings .............................................. 15
16 Dimensions of Class 300Caps ............................................................. 16
17 Dimensions of Class 300. 90 deg and 45 deg Street Elbows ................................ 17
18 Dimensions of Class 300 Return Bends .................................................... 18
S T D = A S M E B L b - 3 - E N G L L998 M 0759670 ObL2709 757 E
Mandatory Annex
I References ............................ ................................. ............ 19
Nonmandatory Annex
A Quality Program ................................................................... 21
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
...
VIll
S T D - A S M E B L L - 3 - E N G L L778 H 0757b70 O b L 2 7 L O 9 7 9
ASME 816.3-1998
MALLEABLE IRON THREADED FllTlNGS

Classes 150 and 300
. .
1 SCOPE 3 SIZE
The sizes of the fittings scheduled in Tables 3 through
1.1General
18 are identified by the correspondingnominal’pipe
ThisStandard for malleable ironthreadedfittings, sizes (NPS).
Classes 150 and 300, covers: For reducing tees, crosses, and Y-branches (laterals),
(u) pressure-temperature ratings, the size of the largest run opening shall be given first,
(6) size and method of designating openingsof reduc- followed by the size ofthe opening at the opposite
ing fittings, end oftherun. Where the fitting is a tee or Y-branch
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
( c ) marking, (lateral), the size of the outlet is given last. Where the
(d) material, fittingis a cross, the largest side-outlet opening is the
( e ) dimensions and tolerances, third dimension given, followed by the opposite opening.
(f)threading, and The straight-line sketches of Fig. 1 illustrate how the
(g) coatings. reducing fittings are read.
1.2References 4 MARKING
Standards and specifications adopted by reference in
4.1 Class 150 Fittings
this Standard are shown in Annex I, whichispart of
this Standard. Each Class 150 fitting shall be marked for identifica-
tionwiththe manufacturer’sname or trademark.
1.3 QualitySystems
4.2 Class 300Fittings
Requirements relating tothe product manufacturers’
QualitySystemPrograms are described in AnnexA. Each Class 300 fitting shall be marked for identifica-
tion with:
( u ) the manufacturer’s name or trademark,
2 PRESSURE-TEMPERATURE RATINGS ( b ) the numerals “300,”
( c ) the letters “Ml” to designatemalleable iron,
( a ) Pressure-temperature ratings for these fittings are
shown in Table 1. Ratings are independent of the (d) the size, and
contained fluidand are themaximumnonshockpres- ( e ) othermarkings as permitted by MSS SP-25,
sures at the tabulated temperatures. Intermediate ratings Standard Practice Marking System for Valves, Fittings,
maybe obtained by linear interpolation betweenthe Flanges, andUnions.
temperaturesshown.
(b) The temperatures shown for the corresponding 5 MATERIAL
pressure rating shall be the material temperature of the
pressure-retaining structure. It may be assumed that the 5.1 MalleableIron
material temperature is the same as the fluid temperature.
The chemical and physical properties of the castings
Use of a pressure rating at a material temperature other
shall be in accordance with ASTM A 197, Specification
thanthatofthe contained fluidisthe responsibility
for CupolaMalleable Iron. Themanufacturer shall
of the user and subject tothe requirements ofany
applicablecode.
(c) Class 300 street elbows are not recommended
’ Theuse of theword“nominal”as a modifier of a dimension or
size isintendedto indicatethatthestateddimension or size is
for gagepressuresabove 600 psi. used for purposes of designation.
S T D * A S M E B L b - I - E N G L 1778 m 0757b70 O b L 2 7 L l 305 W
ASME 616.3-1998 MALLEABLE IRON THREADED FllTlNGS
4
TABLE 1 PRESSURE-TEMPERATURE RATINGS L
Temperature, "F Class 150, psig
-20 to 150
200
250
300
300
265
225
185
Sizes
'/r1
2000
1785
1575
1360
Class 300, psis
Sizes
1'/4-2
1500
1350
1200
1050
Sizes
2'1~3
1O00
910
825
735
t2 t .
4
4 X 44XX23TXw2 T e e
4
350 150 [Note (111 1150 900 650
400 . . . 750 935 560

450 ... 725 600 475
500 ... 510 450 385
550 ... 300 300 300
4 4
NOTE:
4X4X2 4X3X2
(1) Permissibleforservicetemperature upto366"F, reflecting
the temperature of saturated steam at 150 psig. Y-Branch Y-Branch
4 4
be prepared to certify thattheproducthasbeen so
produced.
5.2Steel
Class 150 couplings and caps in NPS and vx, v4, 4 4 4
g/' may be made from steel rod or bar with a minimum 4 X 4 X 2 X42X 4 X 3 X 4ZX 3 X Z X 1'12
Cross
yield strength of 30 ksi at the manufacturer's Cross
option. Cross
FIG. 1 IDENTIFICATION OF REDUCING

6 DIMENSIONSAND TOLERANCES
FITTINGS
6.1 General
Tables 3 through 18 of center-to-end dimensions are
those given. The largest opening in areducing fitting
given for both straight and reducing fittings.
governs the tolerances to be applied to all openings.
These tolerances do not apply to return bends and caps.
6.2 Reducing Fittings
The dimensions in Tables 3 through 18 of reducing
fittings are for use only whenmaking patterns for the 7 THREADING
specific reducing fitting in question and do not apply
when a larger size patternisbushedtomake the 7.1 Types of Threads
reducing fitting wanted.
All fittings shall be threadedaccording to ASME
6.3 Tolerances B 1.20. I , Pipe Threads,GeneralPurpose (Inch), and
shall
havetaper threads, exceptwroughtcouplings
It is recognized thatsome variations are absolutely (Table 8) andwrought caps(Table 9) in NPS PX, Vd,
unavoidable in themaking of patterns and castings. and
whichmay have straight threads.
Thefollowing tolerances shall be permitted.
(a) Metal Thickness Tolerances. Metal thickness at
7.2 Tolerances
no point in the castings shall be lessthan 90% ofthe
valuegiven in the tables. Variations in taper threading shall be limited to one
(b) Center-to-EndTolerances. Permitted tolerances turn large orone turn smallfromthe gaging face on
on the center-to-enddimensions of the fittings are ring andgaging notchonplugwhenusing working
shown in Table 2. Tolerances for end-to-end dimensions gages. The variations in straight threading shall be
and lengths of couplings andreducersshallbe twice limitedto one and one-half turns large or smallfrom
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
STD=ASME B L b - I - E N G L L778 D 0757b70 Ob22712 2111 m
MALLEABLE IRON THREADED FITTINGS ASME 616.3-1998
TABLE 2 INSPECTION TOLERANCES

Tolerance
Nominal
Pipe Size Plus or Minus,
in.
0.03
0.04
0.05
0.06 Point of last thread
0.07
0.08 Plane of gaging notch
0.10
[Note (2)l
0.12
O. 14
the gaging notchonplugwhenusing a taper pipe GENERAL NOTE:

thread workinggage.Thereferencepointforgaging Enlarged view showing chamfered internal thread of basic
internal fittings threads depends upon the chamfer diam- size with chamfer exceeding the major diameter.
eter. When the internal chamferdiameterexceeds the NOTES:
majordiameter of the internal thread,the reference (1)Thechamferillustratedisata 45 degangleand is
pointis the last thread scratch onthe chamfercone. approximately 3/8 pitch in depth. However, these details
are not requirements and are given only for information
When the internal chamferdiameterdoes not exceed
on the illustration shown.
the major diameter of the internal thread, the reference (2) Plane of gaging notch should intersect crestof thread on
point is the endof the fitting (see Fig. 2). gage.
7.3 Countersink or Chamfer

FIG. 2GAGING OF
For the purpose of easier entrance in making joint
a CHAMFERED INTERNAL THREADS
andfor protection of the thread, all internal threads
shall be countersunka distance of not less than one-
half the pitch of the threadatan angle of approximately thickness ofthe fitting. Right-hand couplings shall have
45 degwiththe axis of the thread; all external threads notmorethantwo ribs.
shall be chamfered at an angle of 30 deg to 45 deg
with the axis.Countersinking and chamfering shallbe 8.2 Special Couplings
concentric with the threads.
Right- and left-hand couplings shall havefour or
more ribs unless the left-hand opening is clearly marked
7.4 ThreadLength
"L," in which case the use of ribs is optional with the
Thelength of threads specified in all tables shallbe manufacturer.
measured to include the countersink or chamfer.
7.5 Alignment 9 PLUGS, BUSHINGS,AND LOCKNUTS
Themaximumallowable variation in the alignment For dimensions of plugs, bushings, and locknuts to
of threads of all openings of threaded fittings shall be beused in connection with Classes 150 and 300 malka-
0.06 in./ft (0.5%). threaded
iron ble fittings, see ASME B 16.14, Ferrous
Pipe Plugs, Bushings, and Locknuts With Pipe Threads.
8 RIBS
10 FACEBEVEL
8.1General
A bevelnot exceeding 5 deg is permitted on the
Theaddition of ribs or lugs is permittedonthreaded faces of fitting openings.Center-to-end,end-to-end,and
fittings. Where ribs are used, it is recommended thatwidth of band dimensions may include or exclude the
their thickness shall bethe same as specified for metalbevel.
3
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E BLb.3-ENGL 1778 II 0759b70 Ob12713 L88
ASME 816.3-1998 MALLEABLE IRON THREADED FITTINGS
I l
-+
A
L , r t
Elbow Tee Cross 45 deg Elbow
TABLE 3 DIMENSIONS OF CLASS 150,

90 deg ELBOWS, TEES, AND CROSSES, AND 45 deg ELBOWS (STRAIGHT SIZES)
Center- Center-to-End,
Elbows, Tees, to-End, of of Inside Diameter
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
and Nominal Crosses, Thread,45 deg Band, Diameter Metal of Band,

A Elbows,
Of F Thickness, Min.,
Pipe Min., Min.,
Size [Note (111 C B E Min. Max. G H
0.69 ... 0.25 0.20 0.40 0.43 0.09 0.69

0.81 0.73 0.32 0.21 0.54 0.58 0.09 0.84
0.95 0.80 0.36 0.23 0.67 0.72 0.10 1.o1
1.12 0.88 0.43 0.25 0.84 0.90 0.10 1.20
1.31 0.98 0.50 0.27 1.O5 1.11 0.12 1.46
1.50 1.12 0.58 0.30 1.31 1.38 0.13 1.77
1'/4 1.75 1.29 0.67 0.34 1.66 1.73 0.14 2.15

15; 1.94 1.43 0.70 0.37 1.90 1.97 0.15 2.43
2 2.25 1.68 0.75 0.42 2.37 2.44 0.17 2.96
2 5; 2.70 1.95 0.92 O .48 2.87 2.97 0.21 3.59
3 3.08 2.17 0.98 0.55 3.50 3.60 0.23 4.28
3'/2 3.42 2.39 1.O3 0.60 4.00 4.10 0.25 4.84

4 3.79 2.61 1.O8 0.66 4.50 4.60 0.26 5.40
5 4.50 3.05 1.18 0.78 5.56 5.66 0.30 6.58
6 5.13 3.46 1.28 0.90 6.62 6.72 0.34 7.77
GENERAL NOTE: Dimensions are in inches.

NOTE:
(1) Dimensions for reducing elbows and reducing crosses are given in Table 4 and dimensions for reducing tees in Table5.
11 COATINGS 11.2 Steel Fittings

Couplings and caps madefromsteelrod or bar
11.1 Malleable Iron Fittings may have electrodeposited zinc coatings conforming to
ASTM B 633, Type I, Service Condition 4, or cadmium
When malleable ironfittings are zinc coated, they
coatingsconforming toASTM B 766,Type NS. The
shall behot dipped in accordance with ASTM A 153
electrodepositedcoatingsshall be appliedafter
or haveanelectrodeposited zinc coatingconforming
threading.
to ASTM B 633,Type I, ServiceCondition 4. Hot-
dipped coatings shall be 0.0034 in. minimum thickness
11.3 Other Coatings
and applied priorto threading. Electrodeposited zinc
shall be 0.001 in. minimum thickness and applied Othercoatings specified by the purchaser shallbe
following threading. furnishedmeetingtheagreed requirements.
MALLEABLE IRON THREADED F l T l N G S ASME 616.3-1998
Elbow Cros
TABLE 4 DIMENSIONS OF CLASS 150,90 deg ELBOWS AND CROSSES (REDUCING SIZES)
Elbows Crosses
Nominal Pipe Center-to-End Nominal Pipe Center-to-End Center-to-End

Size X z Size X Z Nominal Pipe Size X Z
24 x 78 0.74 0.76 1'/2 x 1 '/4 1.82 1.88 74 x 74 x h

'x '12 1.20 1.22
34 x 0.88 0.90 172 x 1 1.65 1.80 1 x 1 x "4 x 7 4 1.45 1.37
"8 x v* 0.81 0.85 15; x "4 1.52 1.75 1x 1 x Y2
1.67
1.26
1.58
1.36
'/2 x Y8 1.O4 1.O3 2 x 1 '/2 2.02 2.16 IV4 x 1'/4 x 1 x 1
'/2 x v4 0.97 0.98 2x 1.90 2.10 1'/4 x 1'/4 x "4 x 7 4 1.62 1.45
2x1 1.73 2.02
"4 x 'h 1.20 1.22 1'/2 x 1 72 x 1Y4 x 1 7 4 1.82 1.88
74 x 78 1.12 1.13 2x Y4 1.60 1.97 I
V 2x 1'/2 x 1 x 1 1.65 1.80
"4 x Y4 1.O5 1.O8 2'/2 x 2 2.39 2.60 1'/2 x 1 '/2 x "4 x 7 4 1.75 1.52
1 x "4 1.37 1.45 21/2 x 1% 2.16 2.51 2 x 2 x 15; x 1 5 ; 2.16 2.02
1x '/2 1.26 1.36 3 x 2'/2 2.83 2.99 2 x 2 x 1'/4 x 1'/4 1.90 2.10
3x2 2.52 2.89
1 x "8 1.18 1.27 2X2XlX1 1.73 2.02
x1 1 1.58 1.67 4x3 3.30 3.60 2 x 2 x "4 x Y4 1.60 1.97
1Y4 x 7 4 1.45 1.62 2'/2 x 272 x 2 x 2 2.60 2.39
1'/4 x 72 1.34 1.53 3X3X2X2 2.52 2.89
GENERAL NOTES:
(a) Dimensions are in inches.
(b) For dimensions not given, see Table 3.
(c) Reducing sizes of fittings for which dimensions are not given in tables may be produced from regular patterns for listed
sizes b y sand bushing.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E B L b - 3 - E N G L 1778 I0757b70 Ob12715 T50 I
ASME 816.3-1998 MALLEABLEIRONTHREADEDFITTINGS
TABLE 5 DIMENSIONS OF CLASS 150 TEES (REDUCING SIZES)

Center-to-End Center-to-End Center-to-End
Nominal Pipe Nominal Pipe Nominal Pipe
Size X Y Z Size X V Z Size X V Z
'/4x '/4 x '/B 0.74 0.74 0.76 1'/4 x 1x 1 1.58 1.50 1.67 2x Y4 x
2 2.25 1.97 2.25
/'Ex /'E x '/4 0.76 0.76 0.74 1'/4 x 1 x Y4 1.45
1.37 1.62 2X 2
'/2 X 2.25 1.88 2.25
x 78 x '/4 0.88 0.90 1'/4 x 1 x '/2 1.34 1.26 1.53 1'/2X 1'/2 X 2 2.16 2.16 2.02
78 x 78 x '/E 0.81 0.81 0.85 1'/4 x 3/4 x 1'/4 1.75 1.62 1.75 x l5b x 2 2.10 2.10 1.90
7 8 x '14 x 0.95 0.90 0.95 1'/4 x 3/4 x 1 1.58 1.45 1.67 1x 1x 2 2.02 2.02 1.73
"8 x Y4 x '/4 0.88 0.81 0.90 11/4x Y4 x 3/4 1.45 1.31 1.62 2% x 25; x 2 2.39
2.39
2.60
'/4 x '/4 x 78 0.90
0.90
0.88 1'/4 x '/2 x 1.75 1.53 1.75 2'/2 x 2'/2 x 1'12 2.16
2.16
2.51
'/2 x '/2 x 78 1.04 1.04 1.03 x '/z x 1 1.58 1.36 1.67 2'/2 X 2'/2 X 2.45
2.04
2.04
'/2 x 72 x '/4 0.97 0.97 0.98 1 X 1 X I'/4 1.67 1.67 1.58 2'/2 x 2'/2 x 1 1.87
1.87
2.37
'/2 x 78 x '/2 1.12 1.03 1.12 3/4 x 3/4x l'/a 1.62 1.62 1.45 272 x 2'/2 x 4/' 1.74 1.74 2.32
'/2 x /'Bx 78 1.04
0.95 1.03 11/2x 1y2 x 1'/4 1.82 1.82 1.88 2'/2 x 2 x 2'/2 2.70
2.60
2.70
'/2 x '/4 x '/2 1.12 0.98 1.12 1'/2 x 172 x 1 1.65
1.65 1.80 2y7 X 2X2 2.39
2.25
2.60
"8 x 34 x Y2 1.03
1.03
1.04 x 17. x 3/4 1.52 1.52 1.75 2'/2 x I'/> x 2'/2 2.70
2.51
2.70
"4 x "4 x Y2 1.20 1.20 1.22 11/2 x 1'/2 x '/2 1.41 1.41 1.66 2'/2 x 1'/2 x 2 2.39
2.16
2.60
3/4 x "4 x "8 1.12 1.12 1.13 x IV4 x 1.94 1.88 1.94 2x2 x 2v2 2.60
2.60 2.39
3/4 x 3/4 x 1.08
1.05
1.05 1'/2 X 174 X 1'/4 1.82 1.75 1.88 3X 3X 2'/2 2.83 2.83 2.99
4
" x /'T x 74 1.31 1.22 1.31 11/2x l5h x 1 1.65 1.58 1.80 3x 3x 2 2.52 2.52 2.89
74 x '/2 x /'2 1.20 1.12 1.22 1'/2 x 1v4 x 3/4 1.52 1.45 1.75 3x 3x l'/2 2.29 2.29 2.80
"4 x 5; x "8 1.12 1.04 1.13 1'/2 x 11/4x '/2 1.41 1.34 1.66 3x 3x 1'/4 2.17 2.17 2.74
?14 x "8 x 3/4 1.31 1.13 1.31 1'/2 x 1 x 1'/2 1.94 1.80 1.94 3x 3x 1 2.00 2.00 2.66
74 x /'B x 7 8 1.12 0.95 1.13 x 1x 1.82 1.67 1.88 3x 3 x Y4 1.87 2.61
3/4 x x Y4 1.08
1.31 1.31 1'/2 x 1 x 1 1.65 1.50 1.80 3x 272 x 3 3.08 2.99 3.08
5; x '/2 x 3/4 1.22 1.22 1.20 1'/2 x y4x 1'/P 1.94 1.75 1.94 3x 272 x 2'/2 2.83 2.70 2.99
1 x 1 x "4 1.37 1.37 1.45 11/2 x 5; x 1'4 1.94 1.66 1.94 3x 2% x 2 2.52 2.39 2.89
1x 1x 1.26 1.26 1.36 1'/4 x ll/q x 1'/2 1.88 1.88
1.82 3x 2x3 3.08 2.89 3.08
1 x 1 x "8 1.18 1.27
1.18 1x 1x 1.80 1.80 1.65 3x 2x 2 2.52 2.25 2.89
1x 1x 1.11 1.11 1.22 2x 2 x IV2 2.02 2.02 2.16 2'/2 x 2'/2 x 3 2.99 2.99 2.83
1 x 3/, x 1 1.50 1.50
1.45 2x 2 x I'/q 1.90 1.90 2.10 3'/2 x 3'/2 x 2'/2 2.93 2.93 3.24
1x 7 4 x 74 1.37 1.31 1.45 2x 2x 1 1.73 1.73 2.02 4x4x3 3.30 3.30 3.60
1 x 7 4 x '/2 1.26 1.20 1.36 2x 2 x '//, 1.60 1.97
1.60 4 x 4 x 2'/2 3.05
3.05 3.51
1x x 1
/'2 1.50 1.36 1.50 2 x 2 x '/2 1.49 1.49 1.88 4x 4x2 2.74 2.74 3.41
1x x 74
'/2 1.37 1.22 1.45 2 x x 2 2.25 2.25
2.16 4x 4x 2.51 2.51 3.32
1x /'2 x 72 1.26 1.12 1.36 2 x 1% x 1% 2.02 1.94 2.16 4x 3x 4 3.79 3.60 3.79
"4 x 4" x 1 1.45 1.45 1.37 2 x 1% x lv4 1.90 1.82
2.10 3x 3x 4 3.60 3.60 3.30
5; x '/2 x 1 1.36 1.36 1.26 2 x 1'/2 x 1 1.73 1.65 2.02 5x 5x 3 4.22
3.51
1'/4 x 1Y4 x 1 1.58 1.58 1.67 2 x x 2 2.25 2.10 2.25 6 x 6 x 4 4.13
4.13 4.94
l5h x x ?L4 1.45
1.45 1.62 2 x 1'/4 x 1v2 2.02 1.88 2.16 6 x 6 x 3 3.64 3.64 4.75
x x '/2 1.34 1.34 1.53 2 x 1'/4 x l5b 1.90 1.75 2.10 6 x 6 x 21/2 3.39
3.39
4.66
1'/4 x 1'/4 x 1.26 1.26 1.44 2 x 1x 2 2.25 2.02 2.25 6 x 6 x 2 3.08
4.56
x 1 x lY4 1.75 1.67 1.75 2 x 1 x I'/2 2.02 1.80 2.16
GENERALNOTES:
( c ) Reducing sizes of fittings for which dimensions are not given in tables may be produced from regular patterns for listed
sizes by sand bushing.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D * A S M E B L b - 3 - E N G L L778 m 0757670 U b L 2 7 L b 777 m
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
MALLEABLE IRON THREADED FllTlNGS ASME B16.3-1998
TABLE 6 DIMENSIONS OF CLASS 150,45 deg Y-BRANCHES (STRAIGHT SIZES)

Length Width Outside Center- Center- End-
Inside Diameter Diameter to-End to-End to-
Nominal of of Metal
of Fittings, F of Band, Inlet, Outlet, End,
Pipe Thread, Band, Thickness,
Min.,
Size B Min., EMax. Min. G Min., H r ~~~
U V
"8 0.36 0.23 0.67 0.72 0.10 1 .o1 0.50 1.43 1.93
1 0.612.32 1.71
/2 0.43 0.25 0.84 0.90 0.10 1.20
7-3 O.50 0.27 1 .O5 1.11 0.12 1.46 0.722.77 2.05
1 0.58 0.30 1.31 I .38 0.13 1.77 0.85 3.28 2.43
1 '/4 0.67 0.34 1.66 1.73 0.14 2.15 1 .o23.94 2.92
1 '/2 0.70 0.37 1.90 1.97 0.15 2.43 1.10 3.28 4.38
2 0.75 0.42 2.37 2.44 0.17 2.96 1.24 3.93 5.17
27 2 0.92 0.48 2.87 2.97 0.21 3.59 1.52 4.73 6.25
3 0.98 0.55 3.50 3.60 0.23 4.28 1.71 5.55 7.26
4 1 .O8 0.66 4.50 4.60 0.26 5.40 2.01 6.97 8.98
ASME S16.3-1998 MALLEABLE IRON THREADED FITTINGS
i Both thread
designsapproved
Both thread Both thread

designs approved designs approved
b " J - 4
Street Elbow 45 deg Street Elbow Street Tea
TABLE 7 DIMENSIONS OF CLASS 150 STREET TEES AND 90 deg AND 45 deg STREET ELBOWS
Center-
Length Max.
Width
Length
Center-
Center- Inside Center-to-
Outside
to-Male of Port
Nomi- to-End,
to-End, of of Diameter Of Metal Diameter Male End End External
Diameter
na1 Elbows 45 deg Thread,
Band, Thick- of Band, Elbows 45
Thread,
deg Male
Pipe and Tees, Elbows,Min.,
Min., F ness, and
Min., Tees, Elbows,
Min., End,
Size A C B E Min. Max. G H J K L N
0.69 ... 0.25 0.20

0.40
0.43
0.09
0.69 1 .o0 ... 0.26 0.20
[Note (I)] [Note (I)]
0.81 0.73 0.32 0.21 0.54 0.58 0.09 0.84 1.19 0.94 0.40 0.26
0.95 0.80 0.36 0.23 0.67 0.72 0.10 1.01 1.44 1 .O3 0.41 0.37
1.12 0.88 0.43 0.25 0.84 0.90 0.10 1.20 1.63 1.15 0.53 0.51
1.31 0.98 0.50 0.27 1.05 1.11 0.12 1.46 1.89 1.29 0.55 0.69
1.50 1.12 0.58 0.30 1.31 1.38 0.13 1.77 2.14 1.47 0.68 0.91
1.75 1.29 0.67 0.34 1.66 1.73 0.14 2.15 2.45 1.71 0.71 1.19
1.94 1.43 0.70 0.37 1.90 1.97 0.15 2.43 2.69 1.88 0.72 1.39
2.25 1.68 0.75 0.42 2.37 2.44 0.17 2.96 3.26 2.22 0.76 1.79
2.70 1.95 0.92 0.48 2.87 2.97 0.21 3.59 3.86 2.57 1.14 2.20
[Note (I)] [Note (I)]
3.08 2.17 0.98 0.55
3.50
3.60
0.23
4.28 2.78 1.20 3.00 4.51
[Note (1)l [Note (1)l
1.08 2.61 3.79 0.66 4.50 4.60

3.70 0.26
1.30 3.70
5.40 5.69
4.50 ... 1.18 0.78 5.56 5.66 0.30 6.58 6.86 ...
4.69 1.41
[Note (I)] [Note (1)l
5.13 ... 1.28 0.90 6.62 6.72
0.34
7.77 8.03 . .5.67
. 1.51
[Note (1)l [Note (111
~~~

NOTE:
(1) This dimension applies to street elbows only. Street tees are not made in these sizes.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
Cast Wrought
TABLE 8 DIMENSIONS OF CLASS 150 COUPLINGS (STRAIGHT AND REDUCING SIZES)

Length of
Reducing
Inside Steel Couplings
Width Outside Length Concentric
Length Diameter [Notes (2) and (311
of Metal Diameter Thick- of Couplings,
Nominal of Thread, of Fittings,
Band, Thick- of Band, Straight
ness M Outside
Pipe
Min.
Min.,
F ness, Min., of Couplings, [Notes (1) Length,
Diameter,
Size B L2 E Min. Max. G H Ribs W and (211 W D
/’B 0.25
0.2639 0.20 0.40 0.43 0.09 0.69 0.96
0.09 . . . 0.560.81
’/d 0.32
0.4018 0.21 0.54 0.58 0.09 0.84 0.09 1 .O6 1 .o0 1.19 0.72
’4 0.36
0.4078 0.23 0.67 0.72 0.10 1 .o1 0.10 1.16 1.13 0.871.19
’/z 0.43 .. . 0.25 0.84 0.90 0.10 1.20 0.10 1.34 1.25. . . ...
’4 0.50 .. . 0.27 1.05 1.11 0.12 1.46 0.12 152 1.44 ... ...
1 0.58 ... 0.30 1.31 1.38 0.13 1.77 0.13 1.67 1.69 .. ...
1’/4 0.67 .. . 0.34 1.66 1.73 0.14 2.15 0.14 1.93 2.06 .. ...
I’/z 0.70 .. . 0.37 1.90 1.97 0.15 2.43 0.15 2.15 2.31 .. ...
2 0.75 .. . 0.42 2.37 2.44 0.17 2.96 0.17 2.53 2.81 .. ...
25; 0.92 .. . 0.48 2.87 2.97 0.21 3.59 0.21 2.88 3.25 .. ...
3 0.98 ... 0.55 3.50 3.60 0.23 4.28 0.23 3.18 3.69 ...
4 1.08 ... 0.66 4.50 4.60 0.26 5.40 0.26 3.69 4.38 ...
GENERAL NOTES:
(b) Right- and left-hand pattern couplings are standard only in sizes up to and including NPS 2.
NOTES:
~.
Dimension M for all reduction of reducing couplings (concentric only) shall be the same as shown for the largest opening.
Dimension M for eccentric couplings is not standard; such information should be obtained from the manufacturer.
Couplings NPS and smaller may be cast or made from steel rod with a minimum yield strength of 30 ksi at the option
of the manufacturer.
Steel couplings are made without recess. Dimension 8 for steel couplings is minimum length of perfect thread, and the
length of useful thread ( 8 plus threads with fully formed roots and flat crests) shall be not less thanL2 (effective length of
external thread) required by ASME 81.20.1,Pipe Threads, General Purpose (Inch). See Section 7.
9
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E BLb.3-ENGL 1778 111 0 7 5 7 b 7 0 Ob12717 bTb
ASME B16.3-1998 MALLEABLE IRON THREADED FllTlNGS
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
TABLE 9 DIMENSIONS OFCLASS 150 CAPS
Width Inside Outside
Diameter Height, Thickness
of Metal Diameter
Nominal Length Of of Fittings, Thickness of Band. Min., Thickness of Flat
Band,
Pipe Thread, Min. Min.,
F of Side, Min., H P of Top Caps,
Size B 12 E Max.
Min. G [Note (111 [Note (211 Ribs GI
'18 0.25 0.2639 0.20 0.40 0.43 0.09 0.69 0.53 ... ...
'14 0.32 0.4018 0.21 0.54 0.58 0.09 0.84 0.63 ... ...
"* 0.36 0.4078 0.23 0.67 0.72 0.10 1.o1 0.74 ... ...
'12 0.43 0.5337 0.25 0.84 0.90 0.10 0.10

1.20 0.87 ...
"4 0.50 0.5457 0.27 1.05 1.11 0.1 2 0.12
1.46 0.97 0.13
1 0.6828 0.58 0.30 1.31 1.38 0.13 0.13
1.77 1.16 0.15
I'/4 0.67 0.7068 0.34 1.66 1.73 0.14 2.15 1.28 0.14 0.17
1'/2 0.70 0.7235 0.37 1.90 1.97 0.1 5 0.15

2.43 1.33 0.19
2 0.75 0.7565 0.42 2.37 2.44 0.17 0.17
2.46 1.45 0.22
2 '/2 0.92 1.1375 0.48 2.87 2.97 0.21 0.21
3.59 1.70 0.25
3 0.98 1.2000 0.55 3.50 3.60 0.23 0.23
4.28 1.80 0.29
3 '/2 1.O3 1.2500 0.60 4.00 4.10 0.25 0.25

4.84 1.90 0.30
1 4 .O8 1.3000 0.66 4.50 4.60 0.26 0.26
5.40 2.08 0.36
1.18 5 1.4063 0.78 5.56 5.66 0.30 0.30
6.58 2.32 ...
6 1.28 1.5125 0.90 6.62 6.72 0.34 7.77
0.34 2.55 ...
GENERAL NOTE: Dimensions are i n inches.

NOTES:
(1) Caps sizes va,
and 3/8 may be malleable castings or made from steel rod with a minimum yield strength of 30 ksi at the
option of the manufacturer. When made from steel rod, diameters shall be 0.50, 0.69, and 0.84, respectively. Caps made
from steel rod have no recess.
(2) Caps may be made without recess. Caps so made shall be of such height P that the length of perfect thread shall be not
less than B, and the length of useful thread ( B plus threads with fully formed roots and flat crests) shall be not less than
L2 (effective length of external thread) required by ASME 81.20.1, Pipe Threads, General Purpose (Inch).
IO
MALLEABLE IRON THREADED FllTlNGS ASME B16.3-1998
Closed Open

CLOSED-, MEDIUM-, AND OPEN-PATTERN RETURN BENDS
Inside Outside Center-to-
Center-to-
Center-to-
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
Length of Width of Diameter Diameter

CenterCenterCenter
of Fittings,
Thread, Nominal Band, Metal of Band, (Closed (Open
(Medium
Min., Pipe F Thickness, Min., Pattern),
Pattern],
Pattern),
Size B Max.E Min. G H ßl ß2 R3
'12 0.43 0.25 0.84 0.90 0.12 1.20 1.o0 1.25 1.50
"4 0.50 0.27 1.05 1.11 0.13 1.46 1.25 1.50 2.00
1 0.58 0.30 1.31 1.77
1.38 0.15 1.50 1.87 2.50
1'/4 0.67 0.34 1.66 1.73 0.16 2.15 1.75 2.25 3.00
1v 2 0.70 0.37 1.90 1.97 0.18 2.432.50 2.19 3.50

2 0.75 0.42 2.37 2.44 0.20 2.96 2.62 3.00 4.00
2 '/2 0.92 0.48 2.87 2.97
3.59 0.24 ... ... 4.50
3 0.98 0.55 3.50 3.60 0.27 4.28 ... ... 5.00
4 1.O8 0.66 4.50 4.60 0.31 5.40 ... ... 6.00
GENERAL NOTES:
(b) It is permissible to furnish closed-pattern return bends not banded. Closed-pattern return bends will not make up equally
spaced coils, as the distance center-to-center of t w o adjacent bends is greater than the center-to-center of openings of a
single bend.
S T D - A S M E BLb-3-ENGL 1778 0757b70 Ob12721 259
ASME B16.3-1998 MALLEABLE IRON THREADED FITTINGS
PA"4
I +
Elbow Tee Cross 45 deg Elbow

90 deg ELBOWS, TEES, AND CROSSES, AND 45 deg ELBOWS (STRAIGHT SIZES)
Outside
Inside Diameter
Center-to-End,
Center-to-End,
Length of Width of
Diameter
Nominal Elbows, Tees, Thread,45 deg Band, Metal of Band,
Of Fitting* F
and
Pipe Crosses, Elbows, Min., Min., Thickness, Min.,
Size A C B E Max.
Min. G H
'14 0.38 0.94 0.43 0.81 0.54 0.930.58 0.14

"* 1.O6 0.47 0.88 0.44 0.67 0.72 0.15 1.12
'h 1.25 1.o0 0.57 0.50 0.84 0.90 0.16 1.34
0.64 1.13
"4 1.44 1.05 1.631.11 0.18
1 1.95 1.630.20 1.38
1.31 1.31
0.75 0.62
1'/4 1.94 1.50 0.84 0.69 1.66 1.73 0.22 2.39

1'/2 2.13 1.69 0.87 0.75 1.90 1.97 0.24 2.68
2 2.00 1.o0 0.84 2.37 2.44 0.26 3.28
2 '12 2.94 2.25 1.17 0.94 2.87 2.97 0.31 3.86
3 3.38 2.50 1.23 1.o0 3.50 3.60 0.35 4.62
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E BLb.3-ENGL L998 E 0757b70 Ob12722 190 I
MALLEABLE IRON THREADED FllTlNGS ASME 816.3-1998
TABLE 12 CENTER-TO-END
DIMENSIONS OF CLASS 300, TABLE 13 CENTER-TO-END DIMENSIONS
90 deg ELBOWS (REDUCING SIZES) OF CLASS 300 TEES (REDUCING SIZES)
Center-to-End Center-to-End
Nominal Pipe
Nominal Pipe Size X z Size X V Z
72 x "8 1.19 1.19 '12 x '12 x "8 1.19 1.19 1.19

"4 x 5; 1.31 1.38 '/z x Y* x 'h 1.25 1.19 1.25
1 x Y4 1.50 1.56 3/4 x Y4 x '12 1.31 1.31 1.38
x1 1 1.75 1.81 3//, x 7 2 x "4 1.44 1.38 1.44
172 x 174 2.00 2.06 1x1x "4 1.50 1.50 1.56

2x1 2.25 2.38 lxlx72 1.44 1.44 1.50
2v2 x 2 2.69 2.75 1x1x "8 1.31 1.31 1.44
3 x 2'/2 3.06 3.31 1 x 3,/ x 1 1.63 1.56 1.63
GENERAL NOTES: 1'/4 x 1'/4 x 1 1.75 1.75 1.81

(a) Dimensions are in inches. 174 x 1 '/4 x Y4 1.63 1.63 1.75
(b) For dimensions not given, see Table 11. 1.50 1.50 1.69
1/'4 x 1 v 4 x '/2
(c) Reducing sizes of fittings for which dimensions are not
I
V qx1x1Y4 1.94 1.81 1.94
given in tables may be produced from regular patterns
for listed sizes by sand bushing.
1Y2 x 1 '/2 x 1'/4 2.00 2.00 2.06
172 x 1'/2 x1 1.81 1.81 2.00
172 x 1'/2 x Y4 1.69 1.69 1.88
1x 1'/2 x '/2 1.63 1.63 1.81
1x1x1 '/2 2.13 2.06 2.13
2 x 2 x 1'/2 2.25 2.25 2.38

2 x 2 x 1'/4 2.13 2.13 2.31
2X2X1 2.00 2.00 2.25
2 x 2 x 3/4 1.81 1.81 2.13
2 x 2 x '/2 1.75 1.75 2.06
2 x 1'/2 x 2 2.50 2.38 2.50
2Y2 x 2v2 x 2 2.69 2.69 2.75

2'/2 x 2'/2 x 15; 2.44 2.44 2.63
272 x 2 x 2'/2 2.94 2.75 2.94
3 x 3 x 2'4 3.06 3.06 3.31

3 x 3 ~ 2 2.81 2.81 3.13
3 x 2% x 3 3.38 3.31 3.38
GENERAL NOTES:
given in tables may be produced from regular patterns
13
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
STD-ASIE B L b - I - E N G L L998 0759b70 Ob12723 U27
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
ASME B16.3-1998 IRON MALLEABLE THREADED FllTlNGS
G G
Couplings With Bands Couplings Without Bands
TABLE 14 DIMENSIONS OFCLASS 300 COUPLINGS

LengthOutside
Outside
Length of Width of Inside Diameter Diameter of
NominalBand, Thread, Diameter Metal of Coupling, of Band, Straight
of Fitting, F
Min., Pipe Thickness, Min., H, Min., H Coupling,
Size B E Max. Min. G [Note (111 [Note (211 W
'14 0.43 0.38 0.54 0.58 0.14 0.82 0.93 1.37

"B/ 0.47 0.44 0.67 0.72 0.15 0.97 1.12 1.62
l12 0.57 0.50 0.84 0.90 0.16 1.16 1.34 1.87
"4 0.64 0.56 1.O5 1.11 0.18 1.41 1.63 2.12
1 0.75 0.62 1.31 1.38 0.20 1.71 1.95 2.37
1114 0.84 0.69 1.66 1.73 0.22 2.10 2.39 2.87

15; 0.87 0.75 1.90 1.97 0.24 2.38 2.68 2.87
2 1.o0 0.84 2.37 2.44 0.26 2.89 3.28 3.62
2 '/2 1.17 0.94 2.87 2.97 0.31 3.49 3.86 4.12
3 1.o0 3.50 3.60 0.35 4.20 4.62 4.12

NOTES:
(1) Hl diameter is standard for couplings without bands; Hl = F m i n . + 2G.
(2) H min. is for couplings with bands and is optional with the manufacturer. For information on ribs, see Section 8.
14
TABLE 15 DIMENSIONS OF
CLASS 300 REDUCING COUPLINGS
Nominal PiDe Size Lenuth, W
"
8 x '/4 1.44
'/2 x "
8 1.69
'/2 x Y4 1.69
"
4 x '/2 1.75
74 x 318 1.75
Y4 x '14 1.75
1 x Y4 2.00
1 x 72 2.00
1 x 78 2.00
1 x v4 2.00
1 x 1 2.38
1 x 3/4 2.38
1 '/4 x '/2 2.38
1 Y2 x 1 2.69
1 x 1 2.69
15; x 3/4 2.69
1 '/2 x '/2 2.69
2 x 1 3.19
2x 1 3.19
2 x 1 3.19
2 x "4 3.19
2 x 'h 3.19
2'/2x 2 3.69
2% x 1'/2 3.69
3 x 2'/* 4.06
3x2 4.06
3 x 1'/2 4.06
GENERAL NOTES:
given in the tables may be produced from regular patterns
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E B L b - I - E N G L 1998 W 0759b70Ob12725 9TT m
ASME B16.3-1998 MALLEABLE IRON THREADED FITTINGS
+
H
*
Caps With Recess Caps Without Recess
TABLE 16 DIMENSIONS OF CLASS 300 CAPS

Inside Outside
Length of Width of
Diameter Metal Thickness Height,
Diameter
Thread,Nominal Band,
of Fitting, F
PipeMin., Min., Min., Recommended, of Band, Min., P
Size B E Max. Min. G G1[Note (111 Min., H [Note (211
0.43 0.38 0.54 0.58 0.14 0.18 0.93 0.78

0.47 0.44 0.67 0.72 0.15 0.19 1.12 0.83
0.57 0.50 0.84 0.90 0.16 0.20 1.34 0.98
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
0.64 0.56 1.O5 1.11 0.18 0.23 1.63 1.O8
0.75 0.62 1.31 1.38 0.20 0.25 1.95 1.26
174 0.84 0.69 1.66 1.73 0.22 0.28 2.39 1.38

1’/* 0.87 0.75 1.90 1.97 0.24 0.30 2.68 1.43
2 1.o0 0.84 2.37 2.44 0.26 0.33 3.28 1.68
2 ’/2 1.17 0.94 2.87 2.97 0.31 0.39 3.86 2.06
3 1.23 1.o0 3.50 3.60 0.35 0.44 4.62 2.17

NOTES:
(1) Dimension G1 is recommended but shall in no case be less than dimension G.
(2) Dimension P may be varied to comply with manufacturer‘s practice, and, for caps without recess, shall be of such height
that the length of effective thread shall be not less than B.
S T D * A S M E B L b - 3 - E N G L L778 9 0757b70 Ob1272b 83b m
TABLE 17 DIMENSIONS OF CLASS 300,90 deg AND 45 deg STREET ELBOWS

90 deg Elbows 45 degElbows Length Max.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
Width LengthCenter-
Center- Inside Outside of Port
to-
Center-
to-
Center- of of Diameter Metal Diameter
External
Diameter
Nominal to- Male
to-
Male Thread, Band, Of Fitting' Thick- of Thread,
Band, Male
End, End, End, End, Pipe Min., Min.,
F ness,Min., Min., End,
Size A J C K B E
Max. Min. G H L N
0.94 'h1.44 ... ... 0.43 0.38 0.54 0.58 0.14 0.40 0.93 0.26
1.63 1.06 "8 ... ... 0.47
1.12 0.150.44
0.72 0.67 0.41 0.36
0.57 1.38 1.00'12 2.00 1.25 0.50 0.84 0.90
1.34 0.16 0.49 0.53
0.64 1.56 1.13"4 2.19 1.44 0.56
1.11 1.05 0.18 1.63 0.67 0.55
1.38 1.31 0.62 0.75
1 1.811.631.31 2.56 0.88
0.200.68 1.95
1'/4 2.88 1.94 0.84 2.13 1.50 1.16 0.71 2.39 0.22
0.691.73 1.66
0.87 2.31 1.69
1 'h 3.13 2.13 0.751.97 1.90 0.24 2.68 1.35 0.72
2 3.69 2.50 2.00 2.69 1.o0 0.842.44 2.37 0.26 3.28 0.76 1.75
2 '4 4.50 2.94 ... . . . 2.16 1.14
1.173.86 0.31
0.942.97 2.87
5.13 3.38 3 ... ... 1.23 1.00 3.50 3.60
4.62 0.35 1.20 2.67
17
ASME 816.3-1998 MALLEABLE IRON THREADED FITTINGS
NOTES:
( 1 ) Dimension N may be varied to comply with manufacturer’s
practice.
(2) It is recommended that the distance from the end of the
fitting to the center of the radius R be approximately equal to
the dimension B: radius R is recommended as being one-half
of dimension M.
TABLE 18 DIMENSIONS OF CLASS 300 RETURN BENDS

Inside
Length of Width of Metal Outside
Nominal Center-to-Center, M Band, Diameter Thickness, Diameter
of Fitting, F
Closed Pipe Medium ODen
Min., Min.. G of Band.
size Pattern
Pattern
Pattern B E Max. Min.
[Note (111 Min., H
1.75 1 2.50 3.00 0.75 0.62 1.31 1.38 0.20 1.95

1‘/4 2.25 2.50 3.00 0.84 0.69 1.66 1.73 0.22 2.39
1’/2 3.00 3.50 6.00 0.87 0.75 1.90 1.97 0.24 2.68
0 2 6.00 8.00 1.o0 0.84 2.37 2.44 0.26 3.28

NOTE:
(1) It is recommended that G for return bends be increased by 10% or more.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E BLb.3-ENGL 1778 W 0759b70 Ob12728 L07 W
ANDATORY ANNE)
REFERENCES
The following is a list of publications referenced in IS0 9000-1: 1994,Quality managementand quality
this Standard. assurance standards, Part 1: Guidelines for selection
and use
ASME B 1.20.1- 1983 (R 1992), Pipe Threads, General
IS0 9000-2:1997, Quality management and quality
Purpose (Inch)'
assurance standards, Part 2: Generic guidelines for
ASME B16.14-1991, Ferrous Pipe Plugs, Bushings, and
the application of IS0 9001, IS0 9002, and IS0 9003
Locknuts WithPipe Threads'
IS0 9000-3:1991, Quality management and quality
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
Publisher: American Society ofMechanical Engineers assurance standards, Part 3: Guidelines for the appli-
(ASME), Three Park Avenue, New York, NY 10016- cation of IS0 9001 to the development, supply, and
5990;OrderDepartment:22 Law Drive, Box 2300, maintenance of software
Fairfield, NJ 07007-2300 IS0 9001: 1994,Quality systems: Model for quality
ASTM A 153/A 153M-95, Specification for Zinc Coat- assurance in design, development, production, instal-
ing(Hot-Dip) onIronand Steel Hardware lation, and servicing
ASTM A 197-87(R1992), Specification for Cupola I S 0 9002: 1994, Quality systems: Model for quality
Malleable Iron assurance in productionand servicing
ASTM B 633-85(R1994),SpecificationforElec- I S 0 9003: 1994,Qualitysystems: Model for quality
trodepositedCoatings of Zinc onIronand Steel assurance in final inspection andtest
ASTM B 766-86(R1993),SpecificationforElec- Publisher: International Organization for Standardization
trodeposited Coatings ofCadmium (ISO), 1 rue deVarembé,Case Postale 56, CH-
Publisher: American Society for Testing and Materials 1 12I , Genève 20, SwitzerlandSuisse
(ASTM), 100 Barr Harbor Drive, West Consho- MSS SP-25-1998,Standard Practice MarkingSystem
hocken, PA 19428 for Valves, Fittings, Flanges, andUnions
Publisher: Manufacturers Standardization Society of the
' MayalsobeobtainedfromAmericanNationalStandardsInstitute Valveand Fittings Industry (MSS), 127Park Street,
(ANSI), I I West 42nd Street,New York, NY 10036. NE, Vienna, VA 22 180
19
S T D = A S M E BLb.3-ENGL L778 D 0757b70 ObL2727 545 D
NONMANDATORY ANNEX A
QUALITY SYSTEM PROGRAM
The productsmanufacturedin accordance withthis

Standard shallbeproduced under a quality system
programfollowingtheprinciples of an appropriate
standardfromthe I S 0 9000 series.’ A determination
of the need for registration andor certification of the
productmanufacturer’squalitysystemprogramby an
independentorganizationshall be theresponsibility of
themanufacturer. The detaileddocumentation demon-
strating program compliance shallbe availabletothe
purchaser at the manufacturer’s facility. A written sum-
mary description of the program utilized by the product
manufacturershallbe available to the purchaserupon
request. The productmanufacturerisdefined as the
entity whose name or trademark appears on the product
in accordance with the marking or identification require-
ments of this Standard.
’ Theseries is also available from the American National Standards

Institute(ANSI)andtheAmericanSociety for Quality(ASQ)as
American National Standards that are identified by a prefix “Q’
in place of the prefix “ISO.” Each standard of the series is listed
underAnnex I.
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
S T D - A S M E BLb.3-ENGL 1998 0757b70 Ob112730 2b7 m
AMERICAN NATIONAL STANDARDS FOR PIPING.

PIPE FLANGES. FITTINGS. AND VALVES
Scheme for the Identification of Piping Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A13. 1.1996

Pipe Threads. General Purpose (Inch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1.20.1-1983(R1992)
Dryseal Pipe Threads (Inch) ...................................................................... B1.20.3-1976(R1991)
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
Cast Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 ........................................ .BI& 1.1998
Malleable Iron Threaded Fittings: Classes 150 and 300 ...................................................... .BI& 3.1998
Gray Iron Threaded Fittings: Classes 125 and 250 .......................................................... .BI& 4.1998
Pipe Flanges and Flanged Fittings (NPS '/*Through NPS 24) ................................................. 81651996
Factory-Made Wrought Steel Buttwelding Fittings.......................................................... .BI& 9.1993
Face-to-Face and End-to-End Dimensions of Valves ....................................................... .B16.1 0.1992
Forged Fittings, Socket-Welding and Threaded. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B16.1 1.1996
Castlron Threaded Drainage Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B 1 6 . 1 2.1998
Ferrous Pipe Pltlgs. Bushings. and Locknuts with Pipe Threads ............................................. .!316.1 4.1991
Cast Bronze Threaded Fittings: Classes 125 and 250 ................................................. B16.15-1985(R1994)
Cast Copper Alloy Solder Joint Pressure Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B16.1 8.1984(R1994)
Metallic Gaskets for Pipe Flanges: Ring.Joint, Spiral.Wound, and Jacketed. .................................. .B16.2 0.1998
Nonmetallic Flat Gaskets for Pipe Flanges ................................................................ .B16.2 1.1992
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings ........................................... .B16.2 2.1995
Cast Copper Alloy Solder Joint Drainage Fittings- DWV .................................................. .B16.2 3.1992
Cast Copper Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 400, 600, 900, 1500, and 2500 . . . .316.2 4.1991(R1998)
Buttwelding Ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B16.2 5.1997
Cast Copper Alloy Fittings for Flared Copper Tubes ....................................................... .B16.2 6.1988
Wrought Steel Buttwelding Short Radius Elbows and Returns.............................................. .B16.2 8.1994
Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings- DWV .......................... .B16.2 9.1994
Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig
(Sizes '/z Through 2) ............................................................................... ,816.33-1990
Valves - Flanged. Threaded, and Welding End........................................................... .B163 4.1996
Orifice Flanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1 6 . 3 6.1996
Large Metallic Valves for Gas Distribution (Manually Operated, NPS 2'4 t o 12, 125 psig Maximum) . . . . . . B16.38-1985(R1994)
Malleable Iron Threaded Pipe Unions .................................................................... .B16.3 9.1998
Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems . . . . . . . . . . . . . . ..B16.4 0.1985(R1994)
Ductile Iron Pipe Flanges and Flanged Fittings, Classes 150 and 300 ........................................ .B16.4 2.1998
Manually Operated Metallic Gas Valves for Use in House Piping Systems ................................... .B16.44 .I995
Cast Iron Fittings for Sovent@ Drainage Systems .......................................................... .B16.4 5.1998
Large Diameter Steel Flanges (NPS 26 Through NPS 60) ................................................... .B16.47.1996
Steel Line Blanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B 1 6 . 4 8.1997
Power Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B31.1-1995
Fuel Gas Piping (not an ANSI standard)................................................................... .B31.2.1968
Process Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 1 . 3.1999
Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids.................................. ,831.4-1992
Refrigeration Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B31. 5.1992
Gas Transmission and Distribution Pipipg Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B31. 8.1995
Building Services Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B31.9.1996
Slurry Transportation Piping Systems .................................................................... .B31.1 1.1989
Manual for Determining the Remaining Strength of Corroded Pipelines ...................................... .B31G.1991
Welded and Seamless Wrought Steel Pipe .............................................................. B36.10M-1996
Stainless Steel Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B36.19M-l985(R1994)
Self-operated and Power-Operated Safety-Related Valves Functional Specification Standard. . . . . . . . . . . . .N278. 1.1975(R1992)
The ASME Publications Catalog shows a complete list of all the Standards published by the Society . For a complimentary
catalog. or the latest information about our publications. callI-800-THE-ASME (1.L100.843.2763) .
--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---
ASME Services
ASME is committed to developing and delivering technical information. At ASME’S Informetion Central, we make
every effort to answer your questions and expedite your orders. Our representatives are ready to assist you in the
following areas:
ASME Press Member Services & Benefits Public Information

Codes & Standards Other ASME Programs Self-study Courses
Credit Card Orders Payment Inquiries Shipping Information
IMechE Publications Professional Development Subscriptions/Journals/Magazines
Meetings & Conferences Short Courses Symposia Volumes
Member Dues Status Publications Technical Papers
How can you reach us? It’s easier than ever!
There are four options for making inquiries* or placing orders. Simply mail, phone, fax, or E-mail us and an Information
Central representative will handle your request.
Call Mail Toll Free Fax-24 hours E-Mail-24 hours

ASME US & Canada: 800-THE-ASME
973-882-1717 Infocentral
Law 22 Drive, Box 2900 (800-843-2763)
973-882-5 155 @asme.org
Fairtïeld, New
Jersey Mexico: 95-800-THE-ASME
00-843-2763) 07007-2900
Universal: 973-882-1 167
* Information Central staff are not permitted to answer inquiries about the technical content of this code or standard.
Information as to whether or not technical inquiries are issued to this code or standard is shown on the copyright
page. All technical inquiries must be submitted in writing to the staff secretary. Additional procedures for inquiries
may be listed within.

Asme B16.3

Uploaded by

Copyright:

Available Formats

Asme B16.3

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Asme B16.3

Uploaded by

Copyright:

Available Formats

--`,`,``,```,,`,,,,`,`,```,``,,-`-`,,`,,`,`,,`---

The American Society of

ASME issues written replies to inquiries concerning interpretations of

No part of this document may be reproduced in any form,

The American Society of Mechanical Engineers

In 1921, theAmerican EngineeringStandardsCommittee, later the AmericanStandards

ASME B16 COMMllTEE

SUBCOMMITTEE B - THREADED FITTINGS (EXCEPT STEEL)

MALLEABLE IRON THREADED FllTlNGS

ASME 616.3-1998 MALLEABLE IRON THREADED FllTlNGS

Temperature, "F Class 150, psig

350 150 [Note (111 1150 900 650

400 . . . 750 935 560

FIG. 1 IDENTIFICATION OF REDUCING

MALLEABLE IRON THREADED FITTINGS ASME 616.3-1998

TABLE 2 INSPECTION TOLERANCES

the gaging notchonplugwhenusing a taper pipe GENERAL NOTE:

7.3 Countersink or Chamfer

7.5 Alignment 9 PLUGS, BUSHINGS,AND LOCKNUTS

ASME 816.3-1998 MALLEABLE IRON THREADED FITTINGS

TABLE 3 DIMENSIONS OF CLASS 150,

and Nominal Crosses, Thread,45 deg Band, Diameter Metal of Band,

0.69 ... 0.25 0.20 0.40 0.43 0.09 0.69

1'/4 1.75 1.29 0.67 0.34 1.66 1.73 0.14 2.15

3'/2 3.42 2.39 1.O3 0.60 4.00 4.10 0.25 4.84

GENERAL NOTE: Dimensions are in inches.

11 COATINGS 11.2 Steel Fittings

Nominal Pipe Center-to-End Nominal Pipe Center-to-End Center-to-End

24 x 78 0.74 0.76 1'/2 x 1 '/4 1.82 1.88 74 x 74 x h

ASME 816.3-1998 MALLEABLEIRONTHREADEDFITTINGS

TABLE 5 DIMENSIONS OF CLASS 150 TEES (REDUCING SIZES)

TABLE 6 DIMENSIONS OF CLASS 150,45 deg Y-BRANCHES (STRAIGHT SIZES)

GENERAL NOTE: Dimensions are in inches.

Both thread Both thread

Street Elbow 45 deg Street Elbow Street Tea

0.69 ... 0.25 0.20

1.08 2.61 3.79 0.66 4.50 4.60

GENERAL NOTE: Dimensions are in inches.

TABLE 8 DIMENSIONS OF CLASS 150 COUPLINGS (STRAIGHT AND REDUCING SIZES)

ASME B16.3-1998 MALLEABLE IRON THREADED FllTlNGS

'12 0.43 0.5337 0.25 0.84 0.90 0.10 0.10

1'/2 0.70 0.7235 0.37 1.90 1.97 0.1 5 0.15

3 '/2 1.O3 1.2500 0.60 4.00 4.10 0.25 0.25

GENERAL NOTE: Dimensions are i n inches.

TABLE 10 DIMENSIONS OF CLASS 150,

Length of Width of Diameter Diameter

1v 2 0.70 0.37 1.90 1.97 0.18 2.432.50 2.19 3.50

ASME B16.3-1998 MALLEABLE IRON THREADED FITTINGS

Elbow Tee Cross 45 deg Elbow

TABLE 11 DIMENSIONS OF CLASS 300,

'14 0.38 0.94 0.43 0.81 0.54 0.930.58 0.14

1'/4 1.94 1.50 0.84 0.69 1.66 1.73 0.22 2.39

GENERAL NOTE: Dimensions are in inches.

MALLEABLE IRON THREADED FllTlNGS ASME 816.3-1998

72 x "8 1.19 1.19 '12 x '12 x "8 1.19 1.19 1.19

172 x 174 2.00 2.06 1x1x "4 1.50 1.50 1.56

GENERAL NOTES: 1'/4 x 1'/4 x 1 1.75 1.75 1.81

2 x 2 x 1'/2 2.25 2.25 2.38

2Y2 x 2v2 x 2 2.69 2.69 2.75