Scribd
Upload
29 views3 pages

Download

This document contains code to connect an ESP32 to WiFi and send sensor data including CO2, CO, alcohol, toluene, NH4, and acetone levels to ThingsBoard using an MQ135 gas sensor. It initializes the WiFi and sensor, calibrates the sensor, reads values from the sensor, and sends the telemetry data to ThingsBoard at 1 second intervals.

Uploaded by

yawolosenan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
29 views3 pages

Download

This document contains code to connect an ESP32 to WiFi and send sensor data including CO2, CO, alcohol, toluene, NH4, and acetone levels to ThingsBoard using an MQ135 gas sensor. It initializes the WiFi and sensor, calibrates the sensor, reads values from the sensor, and sends the telemetry data to ThingsBoard at 1 second intervals.

Uploaded by

yawolosenan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

#include <WiFi.

h>
#include <MQUnifiedsensor.h>
#include <ThingsBoard.h>

const char* ssid = "YOUR_SSID";


const char* password = "YOUR_PASSWORD";

#define TOKEN "YOUR_DEVICE_TOKEN"


#define THINGSBOARD_SERVER "thingsboard.cloud"

// Initialize ThingsBoard client


WiFiClient espClient;
// Initialize ThingsBoard instance
ThingsBoard tb(espClient);
// the Wifi radio's status
int status = WL_IDLE_STATUS;

//Definitions
#define placa "ESP-32"
#define Voltage_Resolution 3.3
#define pin 34 //Analog input 0 of your arduino
#define type "MQ-135" //MQ135
#define ADC_Bit_Resolution 12 // For arduino UNO/MEGA/NANO
#define RatioMQ135CleanAir 3.6//RS / R0 = 3.6 ppm

double CO2 = (0);

MQUnifiedsensor MQ135(placa, Voltage_Resolution, ADC_Bit_Resolution, pin, type);

void setup()
{
Serial.begin(9600);
if(Serial) Serial.println("Serial is open");

WiFi.begin(ssid, password);

Serial.print("Connecting");
while (WiFi.status() != WL_CONNECTED) {
delay(500);
Serial.print(".");
}
Serial.println();

Serial.print("Connected, IP address: ");


Serial.println(WiFi.localIP());

//Set math model to calculate the PPM concentration and the value of constants
MQ135.setRegressionMethod(1); //_PPM = a*ratio^b

MQ135.init();
Serial.print("Calibrating please wait.");
float calcR0 = 0;
for(int i = 1; i<=10; i ++)
{
MQ135.update(); // Update data, the arduino will be read the voltage on the
analog pin
calcR0 += MQ135.calibrate(RatioMQ135CleanAir);
Serial.print(".");
}
MQ135.setR0(calcR0/10);
Serial.println(" done!.");

if(isinf(calcR0)) {Serial.println("Warning: Conection issue founded, R0 is infite


(Open circuit detected) please check your wiring and supply"); while(1);}
if(calcR0 == 0){Serial.println("Warning: Conection issue founded, R0 is zero
(Analog pin with short circuit to ground) please check your wiring and supply");
while(1);}
/***************************** MQ CAlibration
********************************************/
MQ135.serialDebug(false);
}

void loop()
{
if (!tb.connected()) {
// Connect to the ThingsBoard
Serial.print("Connecting to: ");
Serial.print(THINGSBOARD_SERVER);
Serial.print(" with token ");
Serial.println(TOKEN);
if (!tb.connect(THINGSBOARD_SERVER, TOKEN)) {
Serial.println("Failed to connect");
return;
}
}

MQ135.update(); // Update data, the arduino will be read the voltage on the
analog pin

MQ135.setA(110.47); MQ135.setB(-2.862);
CO2 = MQ135.readSensor();

MQ135.setA(605.18); MQ135.setB(-3.937);
float CO = MQ135.readSensor();

MQ135.setA(77.255); MQ135.setB(-3.18);
float Alcohol = MQ135.readSensor();

MQ135.setA(44.947); MQ135.setB(-3.445);
float Toluene = MQ135.readSensor();

MQ135.setA(102.2 ); MQ135.setB(-2.473);
float NH4 = MQ135.readSensor();

MQ135.setA(34.668); MQ135.setB(-3.369);
float Acetone = MQ135.readSensor();

Serial.print("CO2: ");
Serial.println(CO2);
Serial.print("Light level: ");
Serial.println(lux);
Serial.println("Sending data...");

tb.sendTelemetryFloat("CO2", CO2);

tb.sendTelemetryFloat("CO", CO);

tb.sendTelemetryFloat("Alcohol", Alcohol);
tb.sendTelemetryFloat("Toluene", Toluene);

tb.sendTelemetryFloat("NH4", NH4);

tb.sendTelemetryFloat("Acetone", Acetone);

tb.loop();

delay(1000); //Sampling frequency


}

You might also like