Scribd Logo
Upload

Welcome to Scribd!

  • 25 views

    Pypkote AW2mm

    Uploaded by

    sales.arpaaircon
    The document provides information about AW 2 mm tape, which is a coal tar based corrosion protection tape. It details the tape's characteristics and specifications, as well as the application process for wrapping pipes with the tape to protect them from corrosion.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Pypkote AW2mm

    Uploaded by

    sales.arpaaircon
    25 views1 page
    The document provides information about AW 2 mm tape, which is a coal tar based corrosion protection tape. It details the tape's characteristics and specifications, as well as the application process for wrapping pipes with the tape to protect them from corrosion.

    Original Title

    Pypkote_AW2mm

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides information about AW 2 mm tape, which is a coal tar based corrosion protection tape. It details the tape's characteristics and specifications, as well as the application process for wrapping pipes with the tape to protect them from corrosion.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    25 views1 page

    Pypkote AW2mm

    Uploaded by

    sales.arpaaircon
    The document provides information about AW 2 mm tape, which is a coal tar based corrosion protection tape. It details the tape's characteristics and specifications, as well as the application process for wrapping pipes with the tape to protect them from corrosion.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    IWL TAPES

    DESIGNED FOR YEARS OF PERFORMANCE

    AW 2 MM TAPE
    Pypkote AW 2 mm is a Coal Tar Based Corrosion Protection Tape conforming to IS10221 - 1982 /AWWA C 203 specification. It
    comprises of a Coal Tar based mix supported on a fabric of high tensile strength fibreglass. The mix is specially manufactured to
    have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by
    thermofusible HMHDPE Films which aids in the installation process.

    Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL Resin based Synthetic Primer is applied on
    pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the synthetic primer is
    applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is
    advisable to gently heat the synthetic primer coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG
    Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained
    with a minimum of 12.5 mm. A final coat of White Wash is done immediately over the entire coated pipe.

    Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for
    application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm.

    Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to
    Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.

    AW 2 mm Tape

    SI. No Characteristics Test Method Specification

    i Softening Point º C ASTM D-36 65 to 121

    ii Thickness Measurement 2 mm

    iii Penetration at 25ºC, 100g, 5 sec, dmm ASTM D-5 3 to 20

    iv Filler, % IS 1217 20 to 30

    v Peel Test AWWA C 203 PASSES THE TEST

    vi Holiday Test AWWA C 203 PASSES THE TEST AT 10 KV

    vii Tape Width Measurement 1000 ± 10 mm / 500 ± 5 mm

    viii Tape Weight Measurement Minimum 1.35 Kg Per Sqm Per mm

    IWL reserves the right to modify the data shown on the technical sheet without prior notice.
    IWL’s technical office is at your complete disposal to provide assistance and information on the correct use if its products.
    Contacts: W360, North Main Road, Anna Nagar West Extn, Chennai - 600 101, India. Tel: +91-44-45536000. Fax: +91-44-45536111 - www.iwl.in

    IWL

    You might also like