Scribd Logo
Upload

Welcome to Scribd!

  • 5 views

    Footing Calculations

    Uploaded by

    Trending Juan
    This document provides a footing calculation for a structural element. It includes the project geometry, design criteria, design loads, and analysis and design checks. The analysis calculates the maximum bearing pressure and checks for one-way shear and bending capacity. The results of the checks indicate the design is insufficient for shear but adequate for bending.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Footing Calculations

    Uploaded by

    Trending Juan
    5 views4 pages
    This document provides a footing calculation for a structural element. It includes the project geometry, design criteria, design loads, and analysis and design checks. The analysis calculates the maximum bearing pressure and checks for one-way shear and bending capacity. The results of the checks indicate the design is insufficient for shear but adequate for bending.

    Original Title

    Footing-Calculations

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a footing calculation for a structural element. It includes the project geometry, design criteria, design loads, and analysis and design checks. The analysis calculates the maximum bearing pressure and checks for one-way shear and bending capacity. The results of the checks indicate the design is insufficient for shear but adequate for bending.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    5 views4 pages

    Footing Calculations

    Uploaded by

    Trending Juan
    This document provides a footing calculation for a structural element. It includes the project geometry, design criteria, design loads, and analysis and design checks. The analysis calculates the maximum bearing pressure and checks for one-way shear and bending capacity. The results of the checks indicate the design is insufficient for shear but adequate for bending.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Footing Calculation

    Calculation Note

    Prepared by: John Carlo Santos

    Table of Contents:

    I Project Geometry

    Bar Dia. Nos. Remarks Total Nos.


    Top bar 16 mm 10 Both direction 20
    Bot bar 16 mm 10 Both direction 20
    Ties 0 mm 0 Both direction 0

    II Design Criteria

    Steel Properties
    Ultimate Tensile Strenght (Fu) 420 MPa
    Yielding Stress (fy) 248 MPa
    Modulus of Elasticity 200000 MPa
    Unit Weight 7850 kg/m3

    Concrete Properties
    Compressive Strength @ 28 days (f'c) 34 MPa 3000
    Modulus of Elasticity 29326 MPa
    Unit Weight 24 kN/m3
    III Design Loads
    Out-of-service loadings
    VT = 0.0 kN 0
    M = 0 kN-m 0
    In-service loadings
    VT = 829 kN 24.5
    M = 144 kN-m 4.5
    Footing seflweight
    SW = 27 kN

    Length of Ft. = 1.50 m


    Width of Ft. = 1.50 m
    Height of Ft. = 0.5 m
    Volume = 1.1 m3
    Other Load
    Soil above Ft. = 1.5 ( leave blank if not applicable)
    Surcharge = ( leave blank if not applicable)

    Design Loads
    P = 856.0 kN
    M = 144 kN-m

    IV Analysis and Results

    P= 856.00 kN
    M= 144.00 kN-m
    L= 1.50 m
    B= 1.50 m

    IV.1 Solve for Maximum Bearing Pressure along L

    solve for eccentricity e and L/6

    e = M/P
    = 144 kN-m / 856 kN
    = 0.17 m

    L/6 = 1.5 m / 6
    = 0.250 m

    e<L/6, PA exceeds M/S


    Max Bearing Pressure = P/A ± M/S

    X= 3[(1.5m/2) -0.17m]
    X= 1.74 m

    Max Bearing Pressure = 2(856kN) /[1.5m*1.74m]


    Max Bearing Pressure = 655.94 kPa

    Max Bearing Pressure as Per Service Manual = 127 kPa

    V Design Check
    P= 856.00 kN
    c1= 0.3 m
    c2= 0.3 m
    L= 1.50 m
    B= 1.50 m
    h= 0.50 m
    cc= 0.075 m
    d= 0.42 m
    f'c= 34400.00 kpa
    φV= 0.75

    qu (net) = P/A
    = 380.44 kpa

    Design check for one-way shear

    φVc = φ2√f'c(b)(d)
    = 0.75*2√34400kpa*1.5m*0.42m
    = 87.6357 kN

    In "B" direction
    Vu = qu(net) * B*[((L-c2)/2)-d]
    Vu = 380.44kpa*1.5m[((1.5m-0.3m)/2)-0.42m]
    Vu = 102.719 kN
    Vu>Vc;FAIL!

    In "L" direction
    Vu = qu(net) * L*[((B-c1)/2)-d]
    = 380.44kpa*1.5m[((1.5m-0.3m)/2)-0.42m]
    = 102.719 kN
    Vu>Vc;FAIL!

    Design Check in Bending

    Max Moment in "L" direction

    Mu = qu(net) (B/2) ((L-c2)/2)^2


    Mu = 380.44kpa*(1.5m/2)((1.5m-0.3m)/2)^2
    Mu = 102.719 kN-m

    As as per manual = 10*PI*16^2 / 4


    = 502.6548 mm^2

    Asfy = 0.85f'cab
    a = Asfy/(0.85f'c(b))
    a = 2.84219 mm
    Mcap = 0.90Asfy(d-a/2)
    = 4696.14 kn-m

    Mu< Mcap ; OK!

    Max Moment in "B" direction

    Mu = qu(net) (L/2) ((B-c1)/2)^2


    = 380.44kpa*(1.5m/2)((1.5m-0.3m)/2)^2
    = 102.7188 kN-m

    As as per manual = 10*PI*16^2 / 4


    = 502.6548 mm^2

    Asfy = 0.85f'cab
    a = Asfy/(0.85f'c(b))
    a = 2.84219 mm
    Mcap = 0.90Asfy(d-a/2)
    = 4696.14 kn-m

    Mu< Mcap ; OK!

    You might also like