Cello-IQ is a driver behavior monitoring and eco-driving
device, designed to reduce fleet operating costs, improve productivity and increase fleet safety.
The Cello-IQ processes and interprets vehicle dynamics
and driving patterns into a safety score, which reflects the driver’s potential of involvement in a road accident, and an Eco score, indicating the vehicle’s fuel efficiency and emission footprint.
The Cello-IQ is available in three firmware variants:
Cello-IQ 30, Cello-IQ 40 and Cello-IQ 50. Scalability means Flexibility Cello-IQ is available in three firmware variants, enabling easy and rapid OTA upgrade to an advanced version. Cello-IQ Fleet management solution
30 with various interfaces (I/Os), security capabilities and basic driver behavior (GPS-based).
50 Advanced driver behavior capabilities, including accident event logging, recording and reconstruction.
Highlights Emergency Data Recording (EDR) & Accident Recognition [Cello-IQ 50] - detects, logs, reports and uploads accident events and accident raw data for crash event reconstruction on the server side. Driver Behavior Management (DBM) [Cello-IQ 40/50] - detects, processes, logs and reports a wide set of events and raw data related to hazardous or aggressive driving behavior. Providing the following scorings: • Maneuver level safety score • Trip level safety score • Trip level eco-driving score Eco Driving Management [Cello-IQ 40/50] - detects and reports events which feature uneconomical and environmentally unfriendly driving in terms of fuel consumption, emission and accelerated wear and tear. Onboard Trip Level Scoring [Cello-IQ 40/50] - provides trip statistics information, including Eco scoring and Safety scoring based on the onboard information gathered and processed during a trip. Proprietary eCall [Cello-IQ 40/50] - enables automatic dialing of a pre-defined emergency number in case of detected accident. Real-Time Driver Feedback Display (DFD) [Cello-IQ 40/50] - provides continuous real-time, visual and/or audible (via human speech in various languages) feedback to the driver via a dedicated “Driver Feedback Display” (DFD), indicating to the driver the risk level of their driving.
Harsh Hard Sharp Over Wrong Gear Excessive Off Road
Accessories [Cello-IQ 30/40/50] - ability to connect to Cellocator’s accessories (communication,
identification, sensors and application enablers) to suit a wide range of solutions. BT Extender [Cello-IQ 30/40/50] - serves as Bluetooth dual mode gateway to RS232, supporting the wireless communication channels between the Cello-IQ device and other devices with BT/BLE capabilities: • BT Classic - supports the Serial Port Profile (SPP), enabling the usage of any device supporting BT SPP, such as Smartphones and Electronic Logging Devices (ELDs). • BLE mode - supports the communication channel between the Cello-IQ and the MultiSenses (additional logic was developed in the Cello-IQ to manage the MultiSense data) Use Cases Fleet Operators Improving driver behavior by using mentoring plans, thus increasing driver safety and operational efficiency, which consequently leads to significantly reduced costs.
Vehicle Insurers To implement usage-based insurance (UBI) and "pay as you drive (PAYD)" plans.
Car Dealers Improving customer retention by initiating periodic car maintenance services, while also providing crash detection support and an emergency call-out for customers involved in cases of accidents.
Public Transportation Monitoring the driving behavior of employees driving public vehicles can have a considerable, positive impact on the organization by reducing costs (fuel, insurance, wear and tear), while enhancing the levels of operational efficiency and increasing passenger safety.
Car Rental / Car Sharing Companies
Effectively verify drivers by identifying who drives which car, while real-time driver behavior feedback enables the rental company to take immediate preventive actions if required.
Cold Chain Shipments
Assures the required environmental conditions (temperature, humidity, etc.) are maintained during shipments of perishable goods or pharmaceuticals, using the MultiSenses which communicate with the Cello-IQ device over BLE. Drivers can receive real-time updates of any breaches of pre-defined thresholds and take action (such as reset the thermostat) to guarantee compliance with cold chain shipment requirements. Features Comparison Table Feature Sub Feature Cello-IQ 30 Cello-IQ40 Cello-IQ 50 1 Wire Temperature Sensor support √ √ √ GNSS (Glonass & GPS) support √ √ √ Accelerometer-based Ignition sense √ √ √ Speeding √ √ Harsh Acceleration GPS-based √ √ Harsh Brake events √ √ Harsh Turn √ √ Turn & Acceleration - - √ Driver Behavior Maneuvers Turn & Brake - - √ Off Road - - √ Excessive RPM Fleet logic Events only √ Slalom - - √ Crash Fleet logic Events only √ eCall - √ √ Emergency Data Recording (EDR) - - √ OTA Feature Package upgrades √ √ √ Advanced Recovery (AR) √ √ √ DFD - √ √ BT Extender √ √ √
Cello-IQ 40/50: Accelerometer-based events and maneuvers’ scores.
Cello-IQ Specifications Communication 2G GPRS class 10, PDU SMS Quad band: 850, 900, 1800, 1900MHz 3G* NA: UMTS/HSPA/GSM/GPRS/EDGS: 5.76[UL]/7.2[DL] Mbps, 850/1900 EU: UMTS|HSPA: 5.7[UL]/7.2[DL] Mbps, 900/2100 GSM/GPRS/EDGE: 850/900/1800/1900 MHz CDMA* Dual band 800 / 1900 MHz 1xRTT 153.6 kbps UL/DL Power Output 2W, 1W SIM Internal, replaceable, remote PIN code management Antenna Internal, multi band GSM antenna Packet Data TCP/IP, UDP/IP SMS PDU, text SMS for data forwarding GNSS Technology STM STA8088 Chipset Sensitivity (tracking) -162dBm Acquisition (normal) Cold <35Sec, Warm<35Sec, Hot<1Sec Internal Antenna On board, internal patch antenna External Antenna (optional) External Active antenna (2.85V ± 0.5%), SMA connector Firmware controlled receiver antenna source selection Inputs and Outputs Inputs 1 internally pulled down input dedicated for ignition switch 3 internally pulled up Discrete Dry inputs with assignable functionality and configurable threshold for logical high and low states 2 configurable inputs capable to serve as: Frequency counters - configurable resolution; Up to 5kHz input signal; Signal level (3V < Vin ≤ 30V); Accuracy ±2% Analog inputs with variable resolution - 8bit, adapted to 0-2.5V signal, resolution 20mV, accuracy ±20mV; 8bits, adapted to 0-30V signal, resolution 100mV, accuracy ±100mV Discrete Dry – configurable threshold for logical high and low states Discrete Wet - configurable threshold for logical high and low states Outputs 5 general purpose open drain outputs (250mA max) with assignable functionality.
* This variant possess different I/Os - please contact our sales department for more information. Interfaces Voice Interface Cellocator HF compliant Full duplex Echo cancelation Noise suppression Spy listening option Auto-answer option Volume control by single button or two buttons Distress voice call and plain call generation COM port (RS232) Selectable baud rate (9600, 19200 or 115000bps) True RS232 levels 8 bit, 1 Stop Bit, No Parity MDT Interface Garmin™ Interface PSP™ (Car Alarm) Interface Cellocator Serial Protocol Transparent data mode Configuration update Firmware upgrade Debug port External Monitoring of Modem-CPU dialog (RS232 out) 115000bps True RS232 levels 8 bit, 1 Stop Bit, No Parity 1-Wire™ (Dallas port) DS1990A, DS1971 compliant DS18B20 compliant Extended bus current source with 7 mA driving capability Driver management (up to 100 driver IDS) Car Alarm Authorization Accelerometer 3D, ±8g range, 12 Bit representation, 1mg resolution, I2C interface Connectors 20pin Molex, Automotive SMA switch for optional external GPS Antenna Power Input Voltage 7-32VDC Average Current Consumption Normal: 45mA Economic: 16mA Hibernation: <2.1mA Shipment (Off): <20uA (Internal Battery) Internal Battery Li-Ion Polymer, 3.7V, 1000mAh, rechargeable Up to 200 Tx @ 1Msg/min @ 25°C Operating Temperature: -20 (65% charge) to 60°C Battery Monitoring: Temperature (NTC) & voltage Autonomy: Up to 200 Tx @ 1Msg/min @ 25°C Protections: over current, overcharge and over discharge Environment Temperature, operation -30°C to +70°C full performance -40°C to +85°C – degraded communication Temperature, storage -40°C to +85°C Humidity 95% non-condensing Ingress Protection IP40 Vibration, Impact ISO 16750 Vehicle power transient ISO 7637 Test level 4 (e-mark directives compliant) Mounting Tie-wraps and/or two sided adhesive Certifications FCC Part 15 Subpart B, part 22/24 compliant CE CE EMC & R&TTE according to 89/336/EEC or 1999/5/EC CE Safety EN60950-1:2001+A11:2004 CE number - CE 1177,1909 Automotive Directive 2004/104/EC (E-Mark) IC Industrial Canada PTCRB TRP, TIS, Spurious and harmonics emission EN12830 Compliance Suitability: T With 1-wire Temperature Sensor Climatic environment: w/o Cello Protector – B with Cello Protector – D Accuracy class: -10°C to +85°C - 1 <-10°C, > +85°C - 2 Range: -55°C to +125°C Dimensions & Weight Dimensions 91x73x23mm Weight 110gr DFD Specifications Interfaces COM1 Port (RS232) True RS232 Levels 8 bit; 1 Stop Bit; No Parity, 115200 BPS. Proprietary Serial Protocol Connectors 4 pin connector: GND, Power Supply, RS232 TX, RS232 RX Power Input Voltage 7-32VDC Power Consumption Hibernation: 760uA at 12 V Operational : up to 5.4 W assuming all LEDs are illuminating Display LED Array 12 white LEDs Audio Recorded Messages 128Mbytes SDCARD holding voice recordings Loudspeaker 1W Recording Format Sampling rate: 16Khz Encoding: Signed 16 Bit PCM RAW data file format Environment Temperature, operating -15°C to +65°C full performance Temperature, storage -20°C to +85°C Humidity 95% non-condensing Protection IP40 Certifications FCC Part 15 Subpart B, part 22/24 compliant CE CE EMC & R&TTE according to 89/336/EEC or 1999/5/EC CE Safety EN60950-1:2001+A11:2004 Automotive Directive 2004/104/EC (E-Mark) IC Industrial Canada Mechanical Attributes Dimensions ~ 73 x 47x 18.6 mm Weight ~ 62 grams Stand Manually adjustable view angle with screw Mounting Double-sided adhesive tape or screws Cable 4 wires, 28 Gauge, 30 cm long Connector 4 Pins, 2.54 mm Pitch, Single row
This brochure has been provided for general information purposes only. Product specifications are subject to change without notice to improve Cellocator Division reliability, function or design or otherwise. Pointer Telocation Ltd.
