UNCLASSIFIED

1 EXCHANGE01 DEPLOYMENT

1.1.1 ENABLE SERVER ROLES & FEATURES

APPLICABLE SYSTEMS exchange01
APPLICABLE USER administrator

REQUIREMENTS / NOTES
This section will add required roles and features to the OS before installing exchange
software.

[1]

UNCLASSIFIED
 UNCLASSIFIED

A. From Server Manager, click Manage Menu near the top right > select Add Roles
and Features

[2]

UNCLASSIFIED
 UNCLASSIFIED

Add Roles and click Next

Features Wizard:
Before you begin
Add Roles and  Role-based or feature-base installation
Features Wizard:  Remote Desktop Services installation
Installation Type click Next
Add Roles and should see exchange01, make sure it is selected then click
Features Wizard: Next
Server Selection
Add Roles and Click on the File and Storage Services name to expand
Features Wizard: the lower levels.
Server Roles  Fax Server
  File and Storage Services
 Host Guardian Service

Add Roles and Click in the box for File Server to enable it.
Features Wizard:  File and Storage Services
Server Roles   File and iSCSI
 File Server
 BranchCache for Network
 Data Deduplication
 DFS Namespaces
Add Roles and click Next
Features Wizard:
Server Roles
Add Roles and Click in the box for Media Foundation to enable it.
Features Wizard:  Management OData IIS Extension
Features  Media Foundation
 Message Queuing
Add Roles and Click on the Remote Server Administration Tools name
Features Wizard: to expand the lower levels and keep going to AD DS Tools.
Features  Remote Differential Compression
  Remote Server Administration Tools
 Feature Administration Tools
  Role Administration Tools
  AD DA and AD LDS Tools
 Active Directory module for Windows
Powershell
  AD DA Tools
 Active Directory Administrative Center
 AD DS Snap-Ins and Command-Line Tools
 AD LDS Snap-Ins and Command-Line Tools
Add Roles and Click in the boxes at the lowest level (shown in bold) to
Features Wizard: enable the features needed.
Features   Remote Server Administration Tools
 Feature Administration Tools
[3]

UNCLASSIFIED
 UNCLASSIFIED

  Role Administration Tools

  AD DA and AD LDS Tools
 Active Directory module for Windows
Powershell
  AD DA Tools
 Active Directory Administrative Center
 AD DS Snap-Ins and Command-Line
Tools
 AD LDS Snap-Ins and Command-Line Tools
Add Roles and click Next
Features Wizard:
Features
Add Roles and Click Install
Features Wizard:
Confirmation
Add Roles and click Close (no restart is required yet)
Features Wizard:
Results

1.1.2 SD-EXCHANGE01 SERVER PREREQUISIT

SOFTWARE
APPLICABLE SYSTEMS exchange01
APPLICABLE USER administrator

REQUIREMENTS / NOTES
See chapter 2 for loading ISO images into vmserver datastore.

APPLICABLE VARIABLES
$MEDIA.GPO$ See MEDIA VARIABLES

[4]

UNCLASSIFIED
 UNCLASSIFIED

A. Mount disk media $MEDIA.GPO$.

B. Open an explorer window and navigate to DVD Drive D:\cots\Microsoft\Exchange

Prerequisite SW. Right click on vcredist_x64_2012 choose run as administrator

Do you want to allow this app to make changes to your device?

Click Yes
Microsoft Visual C++ 2012 Redistributable (x64)
Check the box for  I agree to the license terms and conditions

Click Install
Click Close

C. Right click on vcredist_x64_2013 choose run as administrator

Do you want to allow this app to make changes to your device?

Click Yes
Microsoft Visual C++ 2013 Redistributable (x64)
Check the box for  I agree to the license terms and conditions

Click Install
Click Close

D. Navigate to D:\cots\Microsoft\Exchange\UCMARedist. Right click on Setup and

choose run as administrator

Do you want to allow this app to make changes to your device?

Click Yes
Microsoft Unified Communications Managed API 4.0, Runtime Setup
Click Next
Microsoft Unified Communications Managed API 4.0, Runtime Setup
Check the box for  I have read and accept the license terms.
Leave  Yes, sed information about my setup experiences to Microsoft corporation.
Unchecked

Click Install
Click Finish

[5]

UNCLASSIFIED
 UNCLASSIFIED

1.1.3 INSTALLATION of EXCHANGE SERVER SOFTWARE

APPLICABLE SYSTEMS exchange01 VM
APPLICABLE USER administrator
APPLICABLE INTERFACE Remote Desktop to exchange01 from any network connected
workstation

APPLICABLE VARIABLES
$MEDIA.GPO$ See MEDIA VARIABLES

REQUIREMENTS / NOTES

This section will install exchange server 2019 software.

[6]

UNCLASSIFIED
 UNCLASSIFIED

A. Navigate to D:\cots\Microsoft\Exchange\. Right click on Setup and choose run as

administrator

Check for Under the Check for Updates? Option,

Updates select Don’t check for updates right now

Click -> Next

Introduction -> Next
License Check the box for I accept the terms in the license agreement
Agreement
Click -> Next
Recommended Choose Don’t use recommended settings
Settings
Click -> Next
Server Role Check boxes for Mailbox role ; Management tools ;
Selection Automatically install Windows server roles and features …

Click -> Next

Installation Leave defaults
Space and
Location Click -> Next
Exchange Fill in the organization name: “<DOMAIN>
Organization
Click -> Next
Malware Disable malware scanning. Select Yes
Protection
Settings Click -> Next
Readiness 2 warnings show up here. That’s normal.
Checks
Click -> Install

NOTE:
This install process of the Exchange Server software can take ~40 minutes. Be
patient.

Setup Completed Click -> Finish

REBOOT Server

[7]

UNCLASSIFIED
 UNCLASSIFIED

1.1.4 CONFIGURE EXCHANGE INTERNAL SMTP RELAY

APPLICABLE SYSTEMS exchange01
APPLICABLE USER administrator

REQUIREMENTS / NOTES
During exchange configuration, you must always login with domain administrator
credentials or else the Exchange installation will fail.

A. Configure Internal SMTP Relay.

Desktop Open a Microsoft Explorer browser window

Set up Internet Select  Don’t use recommended settings and
Explorer 11 Uncheck  Send Do Not Track requests to tell sites you
prefer not to be tracked

Click -> OK
Set up Internet At bottom of pop-up window there is a message saying “The
Explorer 11 ‘Skype for Business Browser Helper’ add-on from ‘Microsoft
Corporation’ is ready for use.”
Click the “X” on the right to not make a decision.
Internet Explorer Navigate to https://exchange01/ecp

Login with <DOMAIN>\administrator credentials

Exchange In the drop-down menu for Language select English and
welcome wizard then select the appropriate time zone.
Exchange – mail Click the plus sign + to add a connector
flow – receive
connectors
Exchange - new Enter the name internalSMTPRelay, choose role
receive connector Front End Transport and choose type Internal

Click -> Next

Exchange - new Click the - sign to delete the shown IP address range
receive connector
Popup-Error This field is required
Exchange - new Click the + sign to add a new IP address range, enter the
receive connector network ID(s): x.x.x.x/16

Click -> save, then Click -> finish

Exchange - mail Click the internalSMTPRelay row then click the pencil
flow – receive icon to edit
[8]

UNCLASSIFIED
 UNCLASSIFIED

connector
Exchange - Click the security tab and set the following options:
internalSMTPRela Uncheck the box(es) for: Transport Layer Security (TLS)
y Check the box for: Anonymous users

Click -> Save

Exchange – admin Click recipients on the left, then groups in the center
center
Exchange – Click the plus sign + to add a group, select type
recipients - groups Distribution Group
Exchange – new Set the following values:
distribution group ∙ Display Name: Storage Admins
∙ Alias: storageadmins
∙ Next to Organizational Unit, click Browse. . . then
select Users and OK
∙ In the Members section, click the plus sign + to add
the member Administrator and OK

Click -> Save

Exchange – Click the Storage Admins row then click the pencil icon to edit
recipients - groups
Exchange – Click delivery management, then select Senders inside
Storage Admins and outside my organization

Click -> Save

B. Configure Internal DNS Lookup.

Desktop Open Internet Explorer if not already open

Internet Explorer Navigate to https://exchange01/ecp

Login with <DOMAIN>\administrator credentials

Exchange admin Click servers on the left then click the pencil icon to edit
center
Nel-exchange01 Click DNS Lookups on the left
Nel-exchange01 Click the dropdown for Internal DNS lookups and chose the
‘hostname’ NIC

Click -> Save

[9]

UNCLASSIFIED
 UNCLASSIFIED

C. Click on the Start icon, search for Exchange Management Shell, Right click on the
search result name and select Run as administrator.

PS > Get-ReceiveConnector “internalSMTPRelay” `

| Add-ADPermission -user “NT AUTHORITY\ANONYMOUS LOGON” `
-ExtendedRights “MS-Exch-SMTP-Accept-Any-Recipient”

D. Install Complete

[10]

UNCLASSIFIED