ASSESSMENT TEST ONE (1) REVISIONAL WORKSHEET YEAR 12 TECHNICAL DRAWING

MULTIPLE CHOICE QUESTION (MCQ)

6. The diagram on the right will produce the true shape of a/ an

1. The diagram given below shows a plain scale which measures
up to 4 metres. The reading marked X on the scale is A. circle.
B. ellipse.
A. 0m C. parabola.
B. 1m D. hyperbola.
C. 2m
D. 4m

2. The line labeled S shown in the diagram on the right is called 7. The diagram on the right shows a

A. altitude. A. plain scale.

B. generator. B. diagonal scale.
C. line of action. C. reduction scale.
D. Perpendicular D. enlargement scale.

3. The angle marked B in the diagram shown below is called 8. A curve in which the distance between adjacent coils,
measured radially from the center is constant
A. dihedral angle.
B. obtuse angle. A. evolute.
C. helix angle. B. involute.
D. lead angle. C. logarithmic spiral.
D. archimedean spiral.

4. The line AE of a triangle shown on the right is called 9. The centroid of an L shape is found by
A. dividing the L shape into two rectangles and finding the
A. chord. volume of both.
B. median. B. dividing the the L shape into two rectangles and finding
C. bisector. the area of both.
D. segment. C. dividing one rectangle of the L shape.
D. drawing the diagonals.

10.Which of the following rolling wheels best describes a

5. The locus produced by point P in the set up shown on the right is called point lying inside the generating circle which rolls inside
A. epicycloid. the base circle?
B. hypo-cycloid.
C. superior epi-trochoid. A. Superior Hypotrochoid
D. superior hypo-trochoid. B. Inferior Hypotrochoid
C. Superior Epitrochoid
D. Inferior Epitrochoid
QUESTION 1 - PATTERN DESIGN QUESTION
Given: The sketch of a Tile Pattern, the starting centre lines and triangle ABC.
Required:
(i) Enlarge the given triangle by a scale of 2:1
(ii) Draw three circles inscribed inside the enlarged triangle and show all PCs clearly.
(iii) Draw two arcs from the vertices of the enlarged triangle as shown on the sketch.
(iv) Complete the base by drawing two equal circles (R20) touching the vertices of the enlarged triangle.
(v) Draw a tangential arc of radius 50 and show its PCs clearly.
QUESTION 2 – ROLLING WHEELS BASED QUESTIONS PART B
PART A Given: Part of the locus of a point P outside the rolling circle which rolls on a base circle as
shown below.
Given: A rolling circle moving along a curved path in an anti-clockwise direction.
Required: (i) Complete the curve back to its starting point.
Required: (i) Draw the locus of point P as the rolling circle rolls for ½ revolution.
(ii) Name the curve formed. __________________________
(ii) Name the curve formed: _______________________________
QUESTION 3 – HELIX BASED QUESTIONS
PART 1 Given: The following specifications of a helical curve: turns for 1½ revolutions; mean dia. of 40mm and pitch of 70mm.
Required: (i) Determine the height of the cylinder. Height = _________
(ii) Determine the number of equal parts required on the height of the cylinder. No. of equal parts = ___________

PART 2 Given :The sketch ,section of a round / circular right hand compression spring and its axis.
Required: i. Draw the right- hand round / circular right hand compression spring for ¾ revolution with a helical pitch of 180 mm .
ii. state the true length of the helical curve for ½ revolution only. THL=_____________mm
iii. state the pitch length and pitch angle for ½ revolution only. PL=_______________mm , PA=___________(in degrees)

SKETCH- NTS
QUESTION 4 – CONIC SECTION BASED QUESTION
Given: The elevation and true shape of a conic section. Given: An incomplete Plan and Elevation, Point O which is the Vertex of a right
cone, Point D and V which are members of a Parabolic curve and X is where the
Required: (i) Complete the elevation by constructing the cutting plane and
cutting plane cuts the base.
the focal sphere. Required :a)Locate the focal point.
(ii) Label the focal sphere, vertex, focal point and directrix on b)Draw the Focal Sphere.
c)Draw the True shape of the section.
the elevation. d)Complete the Elevation and the Plan.
e)State the Ratio of Eccentricity: ________
QUESTION 5 – DESIGN QUESTION
Answer only one question out of the three questions given. Write the question QUESTION 2
number you have chosen in the box provided
Problem:
QUESTION 1
The diagram below shows a cyclist riding a bicycle on which he wishes to carry
Problem: personal items. These items may get wet or damaged during rainy days or hot sunny
A greenhouse ball which advertises climate change issues, needs to be placed in a days.
popular park. More advocacy is needed to draw attention to the importance of Brief:
minimizing greenhouse effects on human lives.
Design a storage compartment which can be placed just behind the bicycle seat to
Brief: store personal items safely and securely.
Design an attractive stand for the greenhouse ball that may be placed in a water Specification:
fountain in a popular park.
The storage compartment should:
Specification:
1. be strong, secure and safe;
The stand should:
2. be light and easily detachable;
1. be light, safe to use and easy to construct;
3. be made of a combination of metals and plastics;
2. be appealing and attractive in the day and at night;
4. have ample space for storing personal items like wallets, clothes, electronic
3. be made of a combination of metals, ceramics and plastics; gadgets, etc.
4. have provision to show water flowing down the stand. Requirements:
Requirements: (a) Produce two freehand pictorial sketches of the storage compartment.
(a) Produce two freehand pictorial sketches of the greenhouse ball stand. (b) Evaluate each sketch on the following criteria: (i) materials
(b) Evaluate each sketch on the following criteria: (i) materials (ii) aesthetic
(ii) aesthetic (c) Explain with the help of sketches the mechanism used to easily detach the
(c) Explain with the help of sketches how water from the fountain will flow down storage compartment from the bicycle.
the stand and how it can be made attractive at night. (d) Draw a pencil-rendered or a colour-rendered pictorial sketch of the final
solution.
(d) Draw a pencil-rendered or a colour-rendered pictorial sketch of the final
solution.
(a Possible Solution 1 (c)
Possible Solution 2
)

(d)

(b) Criteria Possible Solution 1 Possible Solution 2

(i) Materials

(ii) Aesthetic