Scribd
Upload
6K views3 pages

Error Code Indicator Wincor

The document lists error codes and indicators for a Wincor ATM. It provides error codes ranging from 0:0 to 9:A and brief descriptions of the issues each code represents, such as software errors, communication failures, sensor or mechanical issues.

Uploaded by

DT Miner S3'O
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
6K views3 pages

Error Code Indicator Wincor

The document lists error codes and indicators for a Wincor ATM. It provides error codes ranging from 0:0 to 9:A and brief descriptions of the issues each code represents, such as software errors, communication failures, sensor or mechanical issues.

Uploaded by

DT Miner S3'O
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

ERROR CODE INDICATOR WINCOR

0:9 = Switch interlock open ( front )

1:2 = Switch interlock open ( rear )


0:1 = software error/ rusak
0:6 =chipcard controller problem
0:8 = communication chipcard controller failure
1:0 = battery kososng / failure ( replace controller )

1:1 = firmware controller hilang ( Load firmware/ replace controller )


1:0 = retract full ( clear retract on counter bill by SOP Menu )
1:4 =Kaset empty, removed/ fatal
1:5 = Dispenser module/kabel distributor disconnect
1:6 =kabel distributor/ FL kabeltidakterpasang

1:7 = sensor block/ interrupt cassete divert, reject


1:8 =Extracctor module open / money jam on transport
2:0 =Bin Transport / LVDT Open ( single reject )
2:1 = MDMS Module/ Cable failure
2:2 = Sensos dispenser pick module block/ fail ( cekjaluruang pick module-extractor-staker)

2:3 = Stakerterbukatidaksempurna
2:4 = Sensor kaset reject
2:5 = motor stacker jam ( test level 1 dan 2 / replace stakerataucontrolboard )
2:6 = Gear motor staker jam
2:8 = Shutter terkunci jam

2:9 = Sensor shutter block


0:0 = Dispenser Ready/siapuntukmengeluarkanuang
1:9 = Clamp tersangkutdiposisi Collecting Tray/Stacker.
3:1 = Rak 1 failure ( cekrak 1 / replace extractor )
3:2 = Rak 2 failure ( clean sensor rak / replace extractor unit )
3:3 = Rak 3 failure ( clean sensor rak / replace extractor unit )
3:4 = Rak 4 failure ( clean sensor rak / replace extractor unit )

4:1 = uangdalamkasettidakkeluar, kaset bad ,error


4:2 = uangdalamkasettidakkeluar, kaset bad ,error
4:3 = uangdalamkasettidakkeluar, kaset bad ,error
4:4 = uangdalamkasettidakkeluar, kaset bad ,error
5:1 = uangdalamkasettidakkeluar, kaset bad ,error

5:2 = uangdalamkasettidakkeluar, kaset bad ,error


5:3 = uangdalamkasettidakkeluar, kaset bad ,error
5:4 = uangdalamkasettidakkeluar, kaset bad ,error
6:1 = uangdalamkasettidakkeluar, kaset bad ,error
6:2 = uangdalamkasettidakkeluar, kaset bad ,error

6:3 = uangdalamkasettidakkeluar, kaset bad ,error


6:4 = uangdalamkasettidakkeluar, kaset bad ,error
7:0 = Extractor MDMS not ready ( cek kabel mdms terpasang baik )
7:1 = cek connector kasetdancek sensor rak
7:2 = cek connector kasetdancek sensor rak
7:3 = cek connector kasetdancek sensor rak
7:4 = cek connector kasetdancek sensor rak
8:1 = sensor prisma extractor kotor ( Clean sensor )
8:2 = sensor prisma extractor kotor ( Clean sensor )
8:3 = sensor prisma extractor kotor ( Clean sensor )

8:4 = sensor prisma extractor kotor ( Clean sensor )


9:0 = double sensor stacker block ( clean sensor )
9:1 = sensor stacker block ( clean sensor )
9:2 = sensor stacker block ( clean sensor )
9:3 = sensor stacker block ( clean sensor )
9:4 = sensor stacker block ( clean sensor )
9:5 = Shutter error

9:A = Sensor Shutter error

You might also like