Part : 4 - C9

OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa

European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 1 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

DO2000
Service Tool Users´s Guide

Authorization Date D1 : . . . .10-Feb

. . . . . .-. 1997
........................
Running on PCB : . . . . . . . . GAA
. . . . . 24353
. . . . . .E1
.....................
Software Version : . . . . . . . .GAA
. . . . .30320AAA
...........................
Document Revision:

Date SCN Author Comment

10-Feb-1997 GAA 30320AAA R. Löb Original document

Copyright 1997, OTIS GmbH Berlin

No part of this document may be copied or reproduced in any form or by any means without the prior written consent of
OTIS GmbH..
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 2 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

1 Display and Key Arrangement 3

2 Connection to DCSS 3
3 Dialog Operations 4
3.1 Dialog Hierarchy 4
3.2 Dialog Graphic 4
4 MODULE Operations 5
5 FUNCTION Operations 5
6 SET Operations 6
6.1 Monitor Function (keys: 31) 6
6.1.1 Status Display (keys: 311) 6
6.1.2 Command Status Display (keys: 312) 9
6.1.3 Input Status Display (keys: 313) 10
6.1.4 Output Status Display (keys: 314) 11
6.1.5 Position Status Display (keys: 315) 11
6.1.6 RAM Status Display (keys: 316) 12
6.2 Test Function (keys: 32) 12
6.2.1 Event Logger Display (keys: 321) 13
6.2.2 Error Logger Display (keys: 322) 13
6.2.3 Partnumber Display (keys: 324) 15
6.2.4 Cyclecount Display (keys: 325) 15
6.3 Setup Function (keys: 33) 15
6.3.1 General Setup Display 16
6.3.2 Installation Routine 18
6.3.3 Profile Setup Display (keys: 332) 24
6.3.4 Engineering Parameter Setup Display (keys: 334) 25
6.4 Inspection Function (keys: 34) 26
6.4.1 Inspection Run (keys: 341) 26
6.4.2 Continuous Run (keys: 342) 28
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 3 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

1 Display and Key Arrangement

The service tool front panel consists of a display with 2 lines, 16 characters per line, and 16
keys.
Some keys have a second function which is activated by pressing first the blue button
(represented by the % sign below) and then the key.
The used key arrangement is as shown below:

keys: +----------+---------+---------+---------+
| MODULE | 7 | 8 | 9 |
| |.........|.........|.........|
| (M) |%%%%%%%%%|%%%%%%%%%|%%%%%%%%%|
|----------+---------+---------+---------|
| FUNCTION | 4 | 5 | 6 |
| |.........|.........|.........|
| (F) |%%%%%%%%%|%%%%%%%%%|%%%%%%%%%|
|----------+---------+---------+---------|
| SET | 1 | 2 | 3 |
| |.........|.........|.........|
| (S) |% ON %|% UP %|% DOWN %|
|----------+---------+---------+---------|
|%%%%%%%%%%| 0 | GO ON | CLEAR |
|%%%%%%%%%%|.........|.........|.........|
|%%%%%%%%%%|% OFF %|%GO BACK%|% ENTER %|
+----------+---------+---------+---------+

2 Connection to DCSS

The service tool can be connected with the DCSS by two ways, directly when plugged onto
the DCSS logic board and indirectly if serial link is connected to the MCSS or OCSS in a
311/411 system configuration.

When connected to any subsystem, the service tool conducts self-tests and then executes
the set-up sequence. The following display will be made when normal communication is
established with any subsystem.

+----------------+
| SELF TEST |
|-OK- MECS-MODE |
+----------------+
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 4 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

3 Dialog Operations

3.1 Dialog Hierarchy

The dialog hierarchy consists of the following three layers in correspondence
with the special keys of the service tool: "MODULE", "FUNCTION", "SET".

"MODULE"
|
+---------+---------+
| | |
"FUNCTION" ... ...
|
+-------+-------+-------+-------+
| | | | |
"SET" ... ... ... ...

3.2 Dialog Graphic

A simplified dialog graphic is given below to present an overview of the complete DCSS
service tool menu.

,----------------.
MODULE LEVEL | DCSS = 3 | <----- M ---+
`----------------´ |
|"3" |
,----------------. ^
FUNCTION LEVEL |MONITOR=1 TEST=2| <----- F ---+
|SETUP=3 INSPEC=4| |
`----------------' ^
SET LEVEL | <----- S ---+
,-----------------+--------+-------+----------------. |
|"1" |"2" |"3" |"4" |
,---------------. ,---------------. ,---------------. ,----------------. |
|STATUS = 1 ( 6)| |EVENT = 1 (13)| |INST = 1 (18)| |INSPCT R= 1 (26)| ^
|COMND = 2 ( 9)| |ERROR = 2 (14)| |PROF = 2 (23)| |CONTIN R= 2 (28)| |
|INP = 3 (10)| |PART = 3 (15)| |OTHER = 3 (24)| `----------------' |
|OUTP = 4 (10)| |CYCLECT= 4 (15)| |ENG = 4 (25)| |
|POSITN = 5 (10)| `---------------' |
|RAM = 6 (12)| |
`---------------' ^

Note: To go back into the menu use 'M' to menu level

'F' to function level
'S' to set level
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 5 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

4 MODULE Operations

The following action will be taken when the "MODULE" key on the service tool panel is
pressed:

plugged onto DCSS: plugged onto Subsystem

(311/411 config.)
+----------------+ +----------------+
|WELCOME TO DCSS | |OCSS=1 MCSS=2 |
| DCSS = 3 | |DCSS=3 ...... |
+----------------+ +----------------+

5 FUNCTION Operations

When the key "3" is pressed in MODULE operation or when the "FUNCTION" key is
pressed at lower layer of the hierarchy, the following display will be monitored:
+----------------+
|MONITOR=1 TEST=2|
|SETUP=3 INSPEC=4|
+----------------+

If a key "1" to "4" is pressed the operation shifts to the SET menu level.

For the Monitor Function see chapter 6.1

For the Test Function see chapter 6.2
For the Setup Function see chapter 6.3
For the Inspection Function see chapter 6.4
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 6 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6 SET Operations

6.1 Monitor Function (keys: 31)

When the key "1" is pressed in FUNCTION operation or when the "<SET>" key is pressed
at lower layer of the hierarchy, the following display will be done:

+----------------+ +----------------+
|STATUS=1 COMND=2| |POSITION=5 RAM=6|
|INP=3 OUTP=4 >| < press GOON/GOBACK > | >|
+----------------+ +----------------+

Press the "<GO ON>" or "<GO BACK>" key to toggle between the displays.

Pressing the keys "1" to "6" at this time the operation will shift to the corresponding field.

6.1.1 Status Display (keys: 311)

The status display is the first line display of the MONITOR function. It will be presented at
the first 5 monitor functions. There are two different status displays, depending of the
selected elevator system configuration.

+----------------+
|aa: mmm ccc sss|
| any display |
+----------------+

Description of the first status display line for a DISCRETE INTERFACE configuration
or for RELAY CONTROLLER:

aa = D1 (DCSS default address ; used for multidrop serial link)

mmm = door supervisor state:

SHD = SHut Down Mode
INI = INItialize Mode (resets position)
RDY = ReaDY Mode (normal operation)
ESM = Emergency Stop Mode
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 7 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

ccc = door command state:

DED = deenergize door

OPN = open normal
OPN2 = open second profile
CLS = close normal
CLS2 = close second profile
NDG = nudging
INSP = inspection

---- additional signals for British Standard BS7255----

BSO = open with TCI Box according to British Standard

BSC = close with TCI Box according to British Standard
ERR = error during TCI Box control

sss = door state:

[] = opened
<> = opening
][ = closed
>< = closing
<P> = passenger protection activated

Description of the first status display line for a SERIAL INTERFACE configuration:

aa: = DCSS address:

D1 (DCSS1: default address)
D2 (DCSS2: alternate door)
D3 (DCSS3: double cabin door)
D4 (DCSS4: double cabin alternate door)

mmmm:= door supervisor state:

SHD = shut down mode
INI = initialize mode (resets position)
RDY = ready mode (normal operation)
ESM = emergency stop mode
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 8 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

cccc = door command state given from MCSS via serial link:

Reversal inputs
in operation:
| DOB | LRD | EDP
--------------------------------------------
DED = deenergize ----- | ----- | -----
OPD1 = open door ----- | ----- | -----
OPD2 = open door ----- | ----- | -----
CLD1 = close door ----- | ----- | -----
CLD2 = close door D | L | E
CLD3 = close door D | L | e
CLD4 = close door D | l | e
CLD5 = close door D | ----- | ----- (NDG)
CLD6 = close door D | ----- | e
CLD7 = close door d | ----- | e
CLD8 = close door d | ----- | -----

D full / d limited door reversal, ----- no door reversal on DOB

L full / l limited door reversal, ----- no door reversal on LRD
E full / e limited door reversal, ----- no door reversal on EDP

ss = Door State:
[] = opened
<> = opening
][ = closed
>< = closing
<P> = passenger protection activated

If the safety link is interrupted, indicated by the EDS-signal, the DCSS shuts down and
disables the motor supply. In this mode the Service Tool displays:

+----------------+
| EMERGENCY STOP |
| |
+----------------+
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 9 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.1.2 Command Status Display (keys: 312)

This set is used to display the actual system state and to enter one of the different door
commands, generally coming from the MCSS. This door command can be entered only if
the DO2000 is adjusted to SERIAL configuration and the Service Tool is plugged directly
onto the DCSS.

EXAMPLE: +----------------+ +----------------+

|D1: RDY OPN <> | |D1: RDY CLD6 >< |
|CLD6 < D - e | press ENTER > |CLD6 < D - e |
+----------------+ +----------------+

GENERAL: +----------------+
| Status Display |
|1111 < 2 3 4 |
+----------------+

The different number fields in the display show the available door command and the system
reaction, if the reversal inputs DOB, LRD or EDP are activated. Lower case letters represent
the command "limited", upper case letters the command "full door reversal". A hyphen
means no door reversal (see page 8).

The fields are:

1111 1.) if MCSS is connected static display: MCSS
2.) if SVTOOL is plugged onto DCSS command selection:
DED, OPD1, OPD2, CLD1..CLD8 (see table)

234 shows additional reversal devices info for command currently selected
with 2 = 'D' for full, 'd' for limited reversal
'--' for no reversal on DOB operated

with 3 = 'L' for full, 'l' for limited reversal

'--' for no reversal on LRD operated

with 4 = 'E' for full, 'e' for limited reversal

'--' for no reversal on EDP operated

Use the key "<GO ON>" or "<GO BACK>" to scroll through the available commands.
Press the key "<ENTER>" to confirm the new command.

If the DCSS is adjusted to DISCRETE configuration an error message will be displayed:

+----------------+
|NOT AVAILABLE, |
|PRESS "CLEAR" |
+----------------+
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 10 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.1.3 Input Status Display (keys: 313)

This set is used to display the actual system state and the discrete inputs.
The following display will be made for a DISCRETE INTERFACE configuration:

EXAMPLE: +----------------+ +----------------+

|D1: RDY OPN <> | |D1: RDY OPN <> |
| do ndg tci EDS| < GOON/GOBACK > | prof DOB err |
+----------------+ +----------------+
discrete inputs EDS, DOB are "on"
discrete inputs do, ndg, tci, prof and err are "off"

GENERAL: +----------------+ +----------------+

| Status Display | | Status Display |
| 111 222 333 444| < GOON/GOBACK > | 555 666 777 444|
+----------------+ +----------------+

The different number fields in the display show the discrete inputs, lower case letters
represent the state "off", upper case letters the state "ON".

For a DISCRETE INTERFACE or RELAY CONTROLLER configuration there are following

inputs:

111 DO (door open command) 222 NDG (nudging)

333 TCI (Top of Car Inspection) 444 EDS (emergency door stop)
---------- additional input information only if Relay Interface Box is connected -------------
555 PROF (second profile signal) 666 DOB (door open button)
777 ERR (overcurrent error or PWM disabled)

For a SERIAL INTERFACE configuration there are:

111 SO (save to open) 222 LRD (light ray device)

333 DOB (door open button) 444 EDP (electronic door protector)
555 TCI (top of car inspect.switch) 666 EDS (emergency door stop)
777 ERR (overcurrent error or PWM disabled)

ATTENTION!
The inputs are changing if the door is controlled by the Top of Car Inspection Box according
to the British Standard BS7255:

111 SO (safe to open signal) 222 BSC (Brit.Stand.Close command)

333 BSO (Brit.Stand.Open command)444 TCI (Top of Car Inspection switch)
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 11 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.1.4 Output Status Display (keys: 314)

This set is used to display the actual system state and the discrete outputs.

EXAMPLE: +----------------+
|D1: RDY OPN <> |
| inh dol dos |
+----------------+

GENERAL: +----------------+
| Status Display |
| 1111 2222 3333 |
+----------------+

The different number fields in the display show the discrete outputs, lower case letters
represent the state "off", upper case letters the state "ON".

The outputs are:

DISCRETE:
1111 INH (inverter INHibit) 2222 DOL (Door Open Limit)
3333 DOS (Door Opening Signal)

RELAY CONTROLLER:
1111 REL1 (DOL:door fully open) 2222 REL2 (DCL:door fully closed)
3333 REL3 (GH:door closed)

SCROLL!

4444 REL4 (SGL: 30% before closed) 5555 REL5 (PMY: for high speed drive)
6666 REL6 (SGSout: reopen signal)

6.1.5 Position Status Display (keys: 315)

This Set is used to display the actual system state and the door position.

EXAMPLE: +----------------+
|D1: RDY OPN <> |
|POSIT = 145 mm |
+----------------+

GENERAL: +----------------+
| Status Display |
|POSIT = xxxx mm|
+----------------+

The door position is calculated according to the speed encoder pulses and is displayed in
[mm]. It corresponds to the door way and is '0mm, if the door is fully closed.
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 12 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.1.6 RAM Status Display (keys: 316)

This set is used to display the actual system state and the values in the RAM on the DCSS
control board.

EXAMPLE: +----------------+
|D1: RDY OPN <> |
|0FA6:F0 E0 BE B6|
+----------------+

GENERAL: +----------------+
| Status Display |
|nnnn:d0 d1 d2 d3|
+----------------+

The different fields in the display show:

nnnn = RAM address

d0 = RAM data at RAM address
d1, d2, d3 = next RAM data

All values are displayed in hex format.

Use the key "<GO ON>" or "<GO BACK>" to increment or decrement the RAM address or
type in the address with the number keys.

To enter the hexadecimal RAM address use number keys and confirm it by the
"<ENTER>" key.

The hex 'A' is entered by pressing the 'BLUE' key and the number 4.
The hex 'B' is entered by pressing the 'BLUE' key and the number 5.
The hex 'C' is entered by pressing the 'BLUE' key and the number 6.
The hex 'D' is entered by pressing the 'BLUE' key and the number 7.
The hex 'E' is entered by pressing the 'BLUE' key and the number 8.
The hex 'F' is entered by pressing the 'BLUE' key and the number 9.

6.2 Test Function (keys: 32)

When the key "2" is pressed in FUNCTION operation or when the "SET" key is pressed at
lower layer of the hierarchy, the following display will be made:
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 13 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

+----------------+
|EVENT=1 ERROR=2 |
|PART=3 CYCLCNT=4|
+----------------+

Pressing the keys "1" to "4" at this time the operation will shift to the corresponding field.

6.2.1 Event Logger Display (keys: 321)

The event logger is used to display information about detected events.
Events are counted only for statistical purposes.

EXAMPLE: +----------------+ +----------------+

|R=00450 T=12567| < ON/OFF > |INSPECTION RUN |
|3110 00001 00128| |3110 00001 00128|
+----------------+ +----------------+

GENERAL: +----------------+ +----------------+

|R=rrrrr T=ttttt| < ON/OFF > |dddddddddddddddd|
|cccc nnnnn mmmmm| |cccc nnnnn mmmmm|
+----------------+ +----------------+

The different fields in the display show:

rrrr = runs since last clear of log-entries
ttttt = system time in minutes since last clear of log-entries
cccc = event code (see also event description in the appendix)
nnnnn = number of event occurrences
mmmmm = minutes since last event occurrence
dd... = event description (see also event description in the appendix)

Press <GO ON> or <GO BACK> to scroll through the events, which occurred since the last
system reset.
Press <ENTER> to delete the displayed event.
Press <SEL Out> to delete complete event-log, Runtimer and -counter.
Press <ON> or <OFF> to toggle between the displays of the first line.

NOTE: The events are not stored permanently ! They are lost after disconnecting the
main power.

6.2.2 Error Logger Display (keys: 322)

The error logger is used to display information about detected errors.

EXAMPLE: +----------------+ +----------------+

|R=00450 T=12560| < ON/OFF > |NOT OPD IN TIME |
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 14 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

|3210 00001 00128| |3210 00001 00128|

+----------------+ +----------------+

GENERAL: +----------------+ +----------------+

|R=rrrrr T=ttttt| < ON/OFF > |dddddddddddddddd|
|cccc nnnnn mmmmm| |cccc nnnnn mmmmm|
+----------------+ +----------------+

The different fields in the display show:

rrrr = runs since last reset

ttttt = system time in minutes since last reset
cccc = error code (see also error description in the appendix)
nnnnn = number of error occurrences
mmmmm = minutes since last error occurrence
dd... = error description (see also error description in the appendix)

Press <GO ON> or <GO BACK> to scroll through the errors, which occurred since the last
system reset.

Press <ENTER> to delete the displayed error.

Press <Sel Out> to delete complete error-log, Run-timer and -counter

Press <ON> or <OFF> to toggle between the displays of the first line.

NOTE:

The errors are not stored permanently ! They are lost after disconnecting the
main power.
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 15 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.2.3 Partnumber Display (keys: 324)

This set is used to show the identification numbers of the two memory devices, the software
identification in the EPROM and the setup parameter identification in the E²PROM. The
version number and the date of programming are also displayed.

EXAMPLE: +----------------+
|: GAA30320AAA |
|DO2000 15NOV1996|
+----------------+

GENERAL: +----------------+
| GAAcccccvvv |
|tttt dddddddddd |
+----------------+

The different fields in the display show:

G = country code: Germany

AA = release level of software
ccccc = software configuration code for DCSS
vvv = version Number
tt... = type of DCSS
dd... = date of programming

6.2.4 Cyclecount Display (keys: 325)

This set is used to display the absolute number of door runs and run time, beginning from
the first installation. These numbers are written into the Flash memory for a permanent
storage every 100th cycle for the runs and every day for the time counting.

EXAMPLE: +----------------+
|R: 0006943267 |
|T: 01:012:23:59 |
+----------------+

GENERAL: +----------------+ yy = years

|R: xxxxxxxxxx | ddd = days
|T: yy:ddd:hh:mm | hh = hours
+----------------+ mm = minutes

6.3 Setup Function (keys: 33)

 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 16 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

When the key "3" is pressed in FUNCTION operation or when the "SET" key is pressed at
lower layer of the hierarchy, the system will shift to the setup function and the following
display is shown:

+----------------+
|INST= 1 PROF= 2 |
|OTHER= 3 ENG = 4|
+----------------+

Pressing the keys "1" to "4" at this level you will shift to the corresponding field and a
changing of the setup parameters is possible.

A list of all setup parameters and their value range is shown in the appendix.

A parameter is stored permanently in the Flash memory not before the menu is left with one
of the function key (Modul, Functio or Set).

6.3.1 General Setup Display

The general display for the setup ( keys 332 to 334 ) is:

EXAMPLE: +----------------+
|START OPEN SPEED|
|0008 <-- 0012 Hz|
+----------------+

GENERAL: +----------------+
|1111111111111111|
|2222 <-- 3333 44|
+----------------+

The different number fields in the display show:

11111 name of setup parameter

2222 value stored in the E²PROM
3333 new value
44 unit

Use "<GO ON>" / "<GO BACK>" to scroll through the available setup parameter.
Use the number keys to enter a new value and confirm it with the "<ENTER>" key.
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 17 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

The parameter input is checked to a certain degree by the DCSS before it is overwritten by
a new value. During the parameter entering the value is checked against the upper and
lower limit. If the parameter exceeds this limit it will not be stored into the Flash memory and
the error counter will be incremented.

NOTE:

It is not recommendable to change the parameters during a door movement, because the
system will be shut down immediately.

When the door supervisor is in the 'READY' mode and the door is not in the fully open or
close position, a changing of the setup parameters is not allowed and the following display
will be shown:

+----------------+
|DOOR IS RUNNING |
|PLEASE WAIT |
+----------------+
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 18 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.3.2 Installation Routine

The complete 'Installation Menu' runs partly automatically. Only few confirmations has to be
entered.
In order to simplify the installation the complete procedure is menu-driven and displayed on
the Service Tool. The user only needs to follow the displayed instructions and has to
confirm the requests.

6.3.2.1 Set Default Parameter

For the first time to put the system into operation a set of Default Parameters must be
copied into the empty Flash memory if it is not happened, the system will not run. In case of
a repeated installation this step can be passed over to avoid an unwished overwriting of the
parameter.

1. Step : Start Installation and Set DEFAULT values

,--------------------.
| SET UP ROUTINE |
| GOON WITH ENTER |
`--------------------'

Press ENTER - Key to start Installation Routine.

,--------------------.
| DEFAULT PARAMTR? |
| YES = 1 NO = 2 |
`--------------------'

Enter '1' to write a set of DEFAULT parameter into the EEPROM or enter '2' to go to
next step

2. Step: Set SYSTEM CONFIGURATION

,-------------------.
| Interf: xxxxxxxxx | xxxxxxxxxxx : DISCRETE
| use GOON / ENTER | SERIAL
`-------------------' Interf.BOX

choose System configuration with GOON/GOBACK and confirm it with <ENTER>.

 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 19 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

According to the selected Interface Type the following Menu display differs.

If a DISCRETE Interface was selected no additional SET_UP appears and the Motor check
program will start.

If SERIAL Interface was selected following displays appear:

,------------------.
| ADDRESS: nnnn | nnnn = DCSS_1 (front door)
| use GOON / ENTER | DCSS_2 (altern. Door)
`------------------’ DCSS_3 (for dobble -
DCSS_4 deck cars )

,-----------------. Yes if one DCSS

| Line Terminator?| No if > two DCSS
| YES=1 NO=2 |
`-----------------’ Two DCSS: No at physical nearest
Yes at physical farthest

,-----------------.
|Controller Type? |
| use GOON / Enter|
`-----------------’

,-----------------. ,-----------------.
| Type: MCS 411 | | Other (311...) |
| use GOON / ENTER| GOON |use GOON / ENTER |
`-----------------’ ----> `-----------------´

If Interf. BOX was selected following Display appears:

,-----------------.
| DOS Signal ? |
| YES=1 NO=2 |
`-----------------’

With this parameter the function of the Relay REL3 on the Interface Box can be
programmed. Some Relay controller need a DOS signal, managed by the Relay 3. If the
parameter DOS signal is set, confirmed by entering a ‘1’, the Relay will be set during
opening and will be dropped off by reaching the DOL position.
If the parameter is set to ´2´ the Relay will be set only if the door is nearly closed and will be
dropped off during opening.
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 20 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.3.2.2 Check Motor Rotation

In the next step the system starts with a connection check of the motor and the encoder
installation, well known from the HPDS-VF/DO2000 installation.
A door command has to be entered and the user only needs to confirm the motor rotation
and the corresponding encoder direction signal. If the door movement or the displayed door
state (direction signal) is not according to the entered command the procedure starts again
with an opposite sign.

3. Step: Check of motor rotation

,--------------------.
| CHK MOTOR ROTATN |
| CLS=1 OPN=2 NO=3 |
`--------------------'

Enter a command: '1' for close, '2' for open door or '3' to pass over

,--------------------.
| DOOR IS ........? | closing if '1' had been entered
| YES=1 NO=2 | opening if '2' had been entered
`--------------------'

Watch door movement and confirm with '1' if door runs in right direction. If not, enter
'2' and the procedure will be repeated with an opposite sign.

,--------------------.
| ERR ROTOR SENSE | displayed if error of rotor sense
| GOON WITH ENTER |
`--------------------'
,--------------------.
| ROTOR SENSE OK | displayed if rotor sense is ok
| GOON WITH ENTER |
`--------------------'

Press '<ENTER>' to go to next step!

 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 21 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.3.2.3 Check Encoder Direction Signal

4. Step: Check of Encoder Direction signal

,--------------------.
| CHK SPEEDENCODER |
| CLS=1 OPN=2 NO=3 |
`--------------------'
Enter a command: '1' for close, '2' for open door or '3' to pass over

,--------------------.
| SPEEDENCD OK? ....| >< encoder direction signal: close
| YES = 1 NO = 2 | <> encoder direction signal: open
`--------------------'
If encoder direction signal according to door movement enter '1'. If not enter '2' and
the procedure will be repeated with a changed sign.

,--------------------.
| ENCODER SENSE OK |
| GOON WITH ENTER |
`--------------------'

Press '<ENTER>' to go to next step.

6.3.2.4 Start Learn Run

After these checks an automatic learn run is started to ascertain the door environment
parameters like door-width, motor-turns, encoder resolution and the slippage of the system.

To learn these unknown values the door has to move two times. At the first move the
routine checks the resolution of the encoder device, which can be very high and leads to an
overflow of the counting register or can be very low which leads to bad performances and
great errors during velocity- and position calculation.
To avoid these bad effects, the resolution of the encoder is adapted during the recognition
to an optimum value, to get the best results independent of the given door hardware.
With the second move the complete doorway is measured. This value must be very
accurate, because it will be now the reference for the door position calculation.

At the end of the learn run the actual position is displayed in [mm].
To leave the menu the user has to press the menu-key 'M'.

If an error has been occurred the initialization will be repeated.

5. Step: Automatic Learn Run

 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 22 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

,--------------------.
| START LEARN_RUN |
| PRESS <ENTER> |
`--------------------'

Start Learn Run by pressing '<ENTER>'

,--------------------.
| LEARN_RUN |
| DOOR is CLOSING |
`--------------------'

To find a defined position the door is closing first. If the door is fully closed the
program goes to the next step.

,--------------------.
| LEARN_RUN |
| DOOR is OPENING |
`--------------------'

Door is opening and learns the door environment to adapt the encoder-pulses for
the position- and velocity calculation. If the door is fully opened it will close again.

,---------------------.
| LEARN_RUN |
| POSITION: xxxxx | xxxxx: Position in increments
`---------------------'

Now the door is closing and the position is measured and displayed in absolute
increments.
If the door is fully closed the program goes to the next step.

,---------------------.
| POSITION: xxxxx | xxxxx: Position in mm
| Finish PRESS "M" |
`---------------------'

The absolute door way has been measured and is displayed.

To finish the Installation routine press "M".

Use the keys "SET", "FUNCTION" or "MODULE" to interrupt the installation routine.
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 23 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

The Installation Routine can be selected only, if the SVTOOL is plugged directly onto the
DCSS. In other cases it will display:

+----------------+
| NOT AVAILABLE |
|PLUG SVT ON DCSS|
+----------------+

If the Top of Car Inspection switch (TCI) is not operated, the following error message will be
displayed:

+----------------+
|SET INSPECTION |
|SWITCH TCI |
+----------------+

For more information see field component manual 'Start Up Routine'.

 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 24 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.3.3 Profile Setup Display (keys: 332)

If the performance of the door is not satisfactory, the following profile parameter can be
changed:
START OPEN SPEED creep velocity at the beginning of door opening
STOP OPEN SPEED creep velocity (torque) at the end of door opening
OPEN STOP POINT breaking point at door opening for normal profile
OPN STOP POINT_2 breaking point at door opening for fast profile
START OPEN DIST creep distance to open door lock
STOP CLOSE SPEED creep velocity (torque) at the end of door closing
CLOSE STOP POINT breaking point at door closing for normal profile
CLS STOP POINT_2 breaking point at door closing for fast profile
NUDGING VELOCITY velocity during nudging operation

For the service tool display see chapter 6.3.1

All velocity parameters are declared as default values by the door type specification.
Generally it is not necessary to change these parameters.

6.3.3.1 Other Parameter Setup Display (keys: 333)

This set is used to change the following variables in the E²PROM:

VOLTAGE BOOST voltage offset when frequency is zero to increase motor torque
PASSENGER PROTEC slip limit for obstacle detection / passenger protection
TCI with BS7255 door control with TCI Box according to British Stand. BS7255
MCS411: GSM-DIST to adjust GSM distance (only for MCS411 )
--- Additional Parameter for Relay Controller (with Interface Box) ----

EFS_OPERATION ? flag to enable EFS and disable 2nd.Profile

REL1 - DISTANCE programmable position of Door Open Limit switch
REL2 - DISTANCE programmable position of Door Close Limit switch
REL3 - DISTANCE programmable position of Gate Hoistway Switch
REL4 - CLOSE-DIST programmable position of Safety Gate Lock (close)
REL4 - OPEN-DIST programmable position of Safety Gate Lock (open)
REL5 - DISTANCE programmable position of PMY switch
SGS - DELAY programmable delay of output: Safety Gate Switch
/SGS=0 SGS=1 programmable low or high active input for SGS signal
/SPEED=0 SPEED=1 programmable low or high active input for second profile sig.
/NDG=0 NDG=1 programmable low or high active input for nudging signal

For the service tool display see chapter 6.3.1

 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 25 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.3.4 Engineering Parameter Setup Display (keys: 334)

This set is used to change the following engineering parameters in the E²PROM:

MAX OPEN SPEED maximum open velocity for normal profile

MAX CLOSE SPEED maximum close velocity for normal profile
MAX OPEN SPEED_2 maximum open velocity for fast profile
MAX CLOSE SPEED_2 maximum close velocity for fast profile
START CLOSE SPD creep speed at beginning of door closing
INITIALIZE SPEED maximum speed for initialize run
START CLOSE DIST creep distance at beginning of door closing
ACCEL DIST OPEN distance of begin and end of acceleration in open direction
ACCEL DIST CLOSE distance of begin and end of acceleration in close direction
DECEL DIST OPEN distance of begin and end of deceleration in open direction
DECEL DIST CLOSE distance of begin and end of deceleration in open direction
RAMP DOWN TIME time to ramp down from max. velo. to 0Hz at reversal action
REVERSAL TIME delay time for reopening if velo.= 0
f[U=100%] Motor parameter, F/U characteristic,( max. volt at freq = xHz)
TORQUE LIMIT reduction of voltage in [x%] (Vred. = V - x*V/100) during close
OPD IDLE_VOLTAGE voltage reduction for idle state (DFO for more than 15 sec)
CLD IDLE VOLTAGE voltage reduction for idle state (DCL for more than 15 sec)
NUDGING VOLTAGE reduction of voltage in [x%] (Vred. = V - x*V/100)at NDG-run
OPEN PROTC TIME door opening protection time (unit: 1 sec)
CLOSE PROTC TIME door closing protection time (unit: 1 sec)
NUDNG_PROTC_TIME door nudging protection time (unit: 1 sec)
CHECK SECUR FLAG flag to disable internal checks(disable=0, enable=1)
SYSTEM CONFIG system config. 0=discrete, 1=serial, 2=relay contr.
ROTOR SENSE flag, that defines the direction of motor rotation
ENCODER SENSE flag, that defines the direction of encoder rotation
POSITION_ERROR defines error tolerance of position (max.=40mm)

For the service tool display see chapter 6.1.1

The engineering parameters should not be changed by the field personal

 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 26 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.4 Inspection Function (keys: 34)

This function is provided to enter door commands by the service tool to the DCSS e.g. to
test the door movement or parameter setup. Either a single command like 'Close Door',
'Open Door' and 'Nudging' can be given or a continuous run can be activated. Controlling
the door via the service tool is possible only if the Top of Car Inspection switch 'TCI' is set
and the Service Tool is plugged directly onto the DCSS.

When the key "4" is pressed in FUNCTION operation or when the "SET" key is pressed at
lower layer of the hierarchy, the following displays will be made:

+----------------+
|INSPECTION RUN=1|
|CONTINUOUS RUN=2|
+----------------+

Pressing the keys "1" or "2" at this level the operation will shift to the corresponding field.

6.4.1 Inspection Run (keys: 341)

This set is used to enter single door commands. Six door commands are available:

CLS_1 close normal enter [1]

CLS_2 close second profile enter [2]
OP_1 open normal enter [3]
OP_2 open second profile enter [4]
NDG nudging operation enter [5]
STOP stop door move enter [6]

The commands with the corresponding number are displayed on the SVTOOL and can be
scrolled with the GOON/GOBACK key.

After entering the first command the door supervisor state will change from 'SHUT DOWN
MODE' to 'INITIALIZE MODE' and the door will perform an Initialization run into the given
direction in order to determine its position.
Afterwards the supervisor mode changes to 'READY' and the door movement corresponds
to the normal speed profile.
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 27 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

EXAMPLE: +----------------+
|D1: RDY INSP >< |
|CLS_1=1 op_1=2 >|
+----------------+

GENERAL: +----------------+
| Status Display |
|CLS_1=1 OP_2=2 >|
+----------------+

Lower case letters represent the state "off", upper case letters the state "ON".

Use the keys "1" to "6" to enter a door command.

NOTE:

After leaving this menu point, the given door command will become invalid.
The inspection mode will be interrupted by pulling off the Service Tool plug.

If the TCI switch is not operated, the following error message will be displayed:

+----------------+
|SET INSPECTION |
|SWITCH TCI |
+----------------+
 Part : 4 - C9
OTIS FIELD COMPONENT MANUAL No. :GAA24350AW11IVa
European and Transcontinental
Operations Vintage : 01 / 1
Service Tool User´s Guide
PRODUCT Page : 28 / 28
ADMINISTRATION DCSSIV - DO2000
Service Tool Manual Date : 10-Feb-1997

6.4.2 Continuous Run (keys: 342)

This function provides a continuous door run if the Top of Car Inspection switch 'TCI' is
operated and the Service Tool is plugged directly onto the DCSS. After starting the
Continuous run (press key [1]) the door first performs an initialize run to determine the
actual position. Afterwards the door opens and closes alternately with the normal speed
profile.

EXAMPLE: +----------------+
|D1: RDY INSP |
|START=1 stop=2|
+----------------+

GENERAL: +----------------+
| Status Display |
|start=1 stop=2|
+----------------+

Lower case letters represent the state "off", upper case letters the state "ON".

Use the keys "1" or "2" to start or stop the continuous run.

NOTE:

When leaving this menu point the continuous run will not be interrupted automatically. It
must be switched off by pressing the key [2], pulling off the Service Tool plug or by resetting
the Inspection switch.

If the Top of Car Inspection is not operated, the following error message will be displayed:

+----------------+
|SET INSPECTION |
|SWITCH TCI |
+----------------+