0% found this document useful (0 votes)
64 views7 pages

Tolerance

The document describes a cross-section of a shaft, bush bearing, and housing arrangement. It includes details on fits and tolerances between components based on BS EN 20286-2 tables. Example tolerances for holes of different nominal sizes are also shown.

Uploaded by

mohdmaazkhan025
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
64 views7 pages

Tolerance

The document describes a cross-section of a shaft, bush bearing, and housing arrangement. It includes details on fits and tolerances between components based on BS EN 20286-2 tables. Example tolerances for holes of different nominal sizes are also shown.

Uploaded by

mohdmaazkhan025
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Drawn below is a cross-section through a Shaft, Bush Bearing and Housing

arrangement. The Shaft is a ‘close running’ fit in the Bush Bearing and the Bush
Bearing is a ‘press fit’ in the housing.

Housing

Shaft
Φ72 Φ57

Bush Bearing

Using BS EN 20286-2 Tolerance Tables (supplied), complete the following table:

Between Grade of Type of Fit Limits of Size for: Size of Tolerance


Components Tolerance
Slide Bush 0.030mm
57+0.030

57+0.000
Bush/Shaft H7 g6
Shaft 0.019mm

57-0.010
57-0.029

Light Press Housing 0.030mm


72+0.030

72+0.000
Housing/Bush H7 p6
Bush 0.019mm
72+0.051

72+0.032

(12 marks)
1. Drawn below is a cross-section through a Shaft, Bush Bearing and Housing
arrangement. The Shaft is a press fit in the Bush Bearing and the Bush
Bearing is a roll fit in the housing.

Housing

Shaft

Φ67 Φ46

Bush Bearing

Using BS EN 20286-2 Tolerance Tables (supplied), complete the following table:

Between Grade of Type of Fit Limits of Size for: Width of


Components Tolerance tolerance
band
INTERFERENCE Bush 0.016
FIT
46.000

46.016
Bush/Shaft H6 n5
Shaft 0.011

46.017

46.028
CLEARANCE FIT Housing 0.039

67.000

67.039
Housing/Bush H8 f7
Bush 0.030

66.940

66.970
(12 marks)
6. State the meaning of the following Geometrical Tolerance statement/s as seen
on an engineering drawing (the drawing is in mm):

Datums A, B, C, should be used to take all measurements from.

The two holes have a nominal size of 10mm diameter. The diameter is allowed to
vary between 10.1mm and 9.9mm.

The holes have a positional tolerance that allows them to move within +0.6 of the
diameter. As long as they are within a circle 10.7mm diameter taken from the
centre measurements identified they are ok.
(6 marks)

ISO Tolerances for Holes (ISO 286-2)

Nominal hole sizes (mm)


over 3 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355

inc. 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 400

micrometres
+28 +34 +43 +53 +66 +79 +94 +110 +129 +142 +161
E6 +20 +25 +32 +40 +50 + 60 +72 +85 +100 +110 +125

+32 +40 +50 +61 +75 +90 +107 +125 +146 +162 +185
E7 +20 +25 +32 +40 +50 + 60 +72 +85 +100 +110 +125

+95 +115 +142 +170 +210 +250 +292 +335 +390 +430 +485
E11 +20 +25 +32 +40 +50 + 60 +72 +85 +100 +110 +125

+140 +175 +212 +250 +300 +360 +422 +485 +560 +630 +695
E12 +20 +25 +32 +40 +50 + 60 +72 +85 +100 +110 +125

+200 +245 +302 +370 +440 +520 +612 +715 +820 +920 +1 015
E13 +20 +25 +32 +40 +50 + 60 +72 +85 +100 +110 +125
+18 +22 +27 +33 +41 +49 +58 +68 +79 +88 +98
F6 +10 +13 +16 +20 +2 + 30 +36 43 +50 +56 +62

+22 +28 +34 +41 +50 +60 +71 +83 +96 +108 +119
F7 +10 +13 +16 +20 +25 + 30 +36 43 +50 +56 +62

+28 +35 +43 +53 +64 +76 +90 +106 +122 +137 +151
F8 +10 +13 +16 +20 +25 + 30 +36 43 +50 +56 +62

+12 +14 +17 +20 +25 +29 +34 +39 +44 +49 +54
G6 +4 +5 +6 +7 +9 +10 + 12 +14 +15 +17 +18

+16 +20 +24 +28 +34 +40 +47 +54 +61 +69 +75
G7 +4 +5 +6 +7 +9 +10 + 12 +14 +15 +17 +18

+22 +27 +33 +40 +48 +56 +66 +77 +87 +98 +107
G8 +4 +5 +6 +7 +9 +10 + 12 +14 +15 +17 +18

+8 +9 +11 +13 +16 +19 +22 +25 +29 +32 +36


H6 0 0 0 0 0 0 0 0 0 0 0

+12 +15 +18 +21 +25 +30 +35 +40 +46 +52 +57
H7 0 0 0 0 0 0 0 0 0 0 0

+18 +22 +27 +33 +39 +46 +54 +63 +72 +81 +89
H8 0 0 0 0 0 0 0 0 0 0 0

+30 +36 +43 +52 +62 +74 +87 +100 +115 +130 +140
H9 0 0 0 0 0 0 0 0 0 0 0

+48 +58 +70 +84 +100 +120 +140 +160 +185 +210 +230
H10 0 0 0 0 0 0 0 0 0 0 0

+75 +90 +110 +130 +160 +190 +220 +250 +290 +320 +360
H11 0 0 0 0 0 0 0 0 0 0 0

+5 +5 +6 +8 +10 +13 +16 +18 +22 +25 +29


J6 -3 -4 -5 -5 -6 -6 -6 -7 -7 -7 -7

+6 +8 +10 +12 +14 +18 +22 +26 +30 +36 +39


J7 -6 -7 -8 -9 -11 -12 -13 -14 -16 -16 -18

+10 +12 +15 +20 +24 +28 +34 +41 +47 +55 +60
J8 -8 -10 -12 -13 -15 -18 -20 -22 -25 -26 -29

+4 +4.5 +5.5 +6.5 +8 +9.5 +11 +12.5 +14.5 +16 +18


JS6 -4 -4.5 -5.5 -6.5 -8 -9.5 -11 -12.5 -14.5 -16 -18

+6 +7.5 +9 +10.5 +12.5 +15 +17.5 +20 +23 +26 +28.5


JS7 -6 -7.5 -9 -10.5 -12.5 -15 -17.5 -20 -23 -26 -28.5

+9 +11 +13.5 +16.5 +19.5 +23 +27 +31.5 +36 +40.5 +44.5
JS8 -9 -11 -13.5 -16.5 -19.5 -23 -27 -31.5 -36 -40.5 -44.5

+2 +2 +2 +2 +3 +4 +4 +4 +5 +5 +7
K6 -6 -7 -9 -11 -13 -15 -18 -21 -24 -27 -29

+3 +5 +6 +6 +7 +9 +10 +12 +13 +16 +17


K7 -9 -10 -12 -15 -18 -21 -25 -28 -33 -36 -40

+5 +6 +8 +10 +12 +14 +16 +20 +22 +25 +28


K8 -13 -16 -19 -23 -27 -32 -38 -43 -50 -56 -61

-1 -3 -4 -4 -4 -5 -6 -8 -8 -9 -10
M6 -9 -12 -15 -17 -20 -24 -28 -33 -37 -41 -46

0 0 0 0 0 0 0 0 0 0 0
M7 -12 -15 -18 -21 -25 -30 -35 -40 -46 -52 -57

+2 +1 +2 +4 +5 +5 +6 +8 +9 +9 +11
M8 -16 -21 -25 -29 -34 -41 -48 -55 -63 -72 -78

-5 -7 -9 -11 -12 -14 -16 -20 -22 -25 -26


N6 -13 -16 -20 -24 -28 -33 -38 -45 -51 -57 -62
-4 -4 -5 -7 -8 -9 -10 -12 -14 -14 -16
N7 -16 -19 -23 -28 -33 -39 -45 -52 -60 -66 -73

-2 -3 -3 -3 -3 -4 -4 -4 -5 -5 -5
N8 -20 -25 -30 -36 -42 -50 -58 -67 -77 -86 -94

-9 -12 -15 -18 -21 -26 -30 -36 -41 -47 -51
P6 -17 -21 -26 -31 -37 -45 -52 -61 -70 -79 -87

-8 -9 -11 -14 -17 -21 -24 -28 -33 -36 -41


P7 -20 -24 -29 -35 -42 -51 -59 -68 -79 -88 -98

-12 -15 -18 -22 -26 -32 -37 -43 -50 -56 -62
P8 -30 -37 -45 -55 -65 -78 -91 -106 -122 -137 -151

- -
-
35 37 -56 -58 -71 -85 -89 -97
-12 -16 -20 -24 -29 -44 -47 -61 -68 -75 103
R6 -20 -25 -31 -37 -45 -66 -69 -86 -97
-
-104
- - -
-
- - -81 -83 100 117 121 133
139
54 56

- -
-60
30 32 -38 -41 -53 -63 -74 -78 -87 -93
-11 -13 -16 -20 -25 -48 -50 -67
R7 -23 -28 -34 -41 -50 -88 -90 -
-
-113
- - - -
- - -73 -76 -93 109 126 130 144 150
106
60 62

ISO Tolerances for Shafts (ISO 286-2)

Nominal Shaft Sizes (mm)


over 3 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355

inc. 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 400

micrometres
- - - - - - - - - -
- - - - -
31 32 34 - 660 740 820 920 105 120 135
360 380 410 520 580
-270 -280 -290 -300 0 0 0 460 0 0 0
a12 -390 -430 -470 -510 - - - - - - - - - - -
- - - - -
56 57 64 860 112 120 128 144 157 177 192
660 730 760 920 980
0 0 0 0 0 0 0 0 0 0

-30 -40 -50 -65 -80 -100 -120 -145 -170 -190 -210
d6 -38 -49 -61 -78 -96 -119 -142 -170 -199 -222 -246

-20 -25 -32 -40 -50 -60 -72 -85 -100 -110 -125
e6 -28 -34 -43 -53 -66 -79 -94 -110 -129 -142 -161

-25 - -32 - -40 - -50 -60 -72 -85 -100 -110 -125
e13 -20 -200
245 302 370 -440 -520 -612 -715 -820 -920 -1015

-13 - -16 - -20 - -25 -30 -36 -43 -50 -56 -62
f5 -10 -15
19 24 29 -36 -43 -51 -61 -70 -79 -87

-10 -13 -16 -20 -25 -30 -36 -43 -50 -56 -62
f6 -18 -22 -27 -33 -41 -49 -58 -68 -79 -88 -98

-10 -13 -16 -20 -25 -30 -36 -43 -50 -56 -62
f7 -22 -28 -34 -41 -50 -60 -71 -83 -96 -108 -119

-4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18


g5 -9 -11 -14 -16 -20 -23 -27 -32 -35 -40 -43

-4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18


g6 -12 -14 -17 -20 -25 -29 -34 -39 -44 -49 -54

-4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18


g7 -16 -20 -24 -28 -34 -40 -47 -54 -61 -69 -75
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h4 -4 -4 -5 -6 -7 -8 -10 -12 -14 -16 -18

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h5 -5 -6 -8 -9 -11 -13 -15 -18 -20 -23 -25

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h6 -8 -9 -11 -13 -16 -19 -22 -25 -29 -32 -36

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h7 -12 -15 -18 -21 -25 -30 -35 -40 -46 -52 -57

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h8 -18 -22 -27 -33 -39 -46 -54 -63 -72 -81 -89

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h9 -30 -36 -43 -52 -62 -74 -87 -100 -115 -130 -140

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h10 -48 -58 -70 -84 -100 -120 -140 -160 -185 -210 -230

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h11 -75 -90 -110 -130 -160 -190 -220 -250 -290 -320 -360

-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h12 -120 -150 -180 -210 -250 -300 -350 -400 -460 -520 -570

+3 +4 +5 +5 +6 +6 +6 +7 +7 +7 +7
j5 -2 -2 -3 -4 -5 -7 -9 -11 -13 -16 -18

+6 +7 +8 +9 +11 +12 +13 +14 +16 +16 +18


j6 -2 -2 -3 -4 -5 -7 -9 -11 -13 -16 -18

+8 +10 +12 +13 +15 +18 +20 +22 +25 +26 +29
j7 -4 -5 -6 -8 -10 -12 -15 -18 -21 -26 -28

+2.5 +3 +4 +4.5 +5.5 +6.5 +7.5 +9 +10 +11.5 +12.5


js5 -2.5 -3 -4 -4.5 -5.5 -6.5 -7.5 -9 -10 -11.5 -12.5

+4 +4.5 +5.5 +6.5 +8 +9.5 +11 +12.5 +14.5 +16 +18


js6 -4 -4.5 -5.5 -6.5 -8 -9.5 -11 -12.5 -14.5 -16 -18

+10.5
+6 +7.5 +9 +12.5 +15 +17.5 +20 +23 +26 +28.5
js7 -6 -7.5 -9 -12.5 -15 -17.5 -20 -23 -26 -28.5
-10.5

+6 +7 +9 +11 +13 +15 +18 +21 +24 +27 +29


k5 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4

+9 +10 +12 +15 +18 +21 +25 +28 +33 +36 +40
k6 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4

+13 +16 +19 +23 +27 +32 +38 +43 +50 +56 +61
k7 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4

+9 +12 +15 +17 +20 +24 +28 +33 +37 +43 +46
m5 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21

+12 +15 +18 +21 +25 +30 +35 +40 +46 +52 +57
m6 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21

+16 +21 +25 +29 +34 +41 +48 +55 +63 +72 +78
m7 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21

+13 +16 +20 +24 +28 +33 +38 +45 +51 +57 +62
n5 +8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37

+16 +19 +23 +28 +33 +39 +45 +52 +60 +66 +73
n6 +8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37

+20 +25 +30 +36 +42 +50 +58 +67 +77 +86 +94
n7 +8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37
+17 +21 +26 +31 +37 +45 +52 +61 +70 +79 +87
p5 +12 +15 +18 +22 +26 +32 +37 +43 +50 +56 +62

+20 +24 +29 +35 +42 +51 +59 +68 +79 +88 +98
p6 +12 +15 +18 +22 +26 +32 +37 +43 +50 +56 +62

+6 +6 +7 +7 +8 +9 +9 +1 +1 +14 +15
+10 +12 +13
+23 +28 +34 +41 +50 0 2 3 6 8 0 3 09 13 4 0
r6 +15 +19 +23 +28 +34 +4 +4 +5 +5 +6 +6 +6
6
+8 +8
6 0
+10 +11
+77 +94 +98
1 3 1 4 3 5 8 0 4 8 4

You might also like