Data sheet 6AG1155-6AA01-7BN0

SIPLUS ET 200SP IM155-6PN ST -40 ... +70°C with conformal

coating based on 6ES7155-6AA01-0BN0 . Bundle PROFINET IM, IM
155-6PN ST, max. 32 Peripheriemodules and 16 ET 200AL Modules,
Single Hot SWAP, Bundle contains: Interface-Module (6AG1155-
6AU01-7BN0), Server-Module (6AG1193-6PA00-7AA0), Busadapter
BA 2xRJ45 (6AG1193-6AR00-7AA0)

General information
Product type designation IM 155-6 PN ST
Product function
● I&M data Yes; I&M0 to I&M3
● Module swapping during operation (hot Yes; Single hot swapping
swapping)
● Isochronous mode No
Engineering with
● PROFINET as of GSD version/GSD revision V2.3 / -

Configuration control
via dataset Yes

Supply voltage
Rated value (DC) 24 V
permissible range, lower limit (DC) 19.2 V
permissible range, upper limit (DC) 28.8 V
Reverse polarity protection Yes
Short-circuit protection Yes

6AG1155-6AA01-7BN0 Subject to change without notice

Page 1/5 04/16/2020 © Copyright Siemens
 Mains buffering
● Mains/voltage failure stored energy time 10 ms

Input current
Current consumption (rated value) 450 mA
Current consumption, max. 550 mA
Inrush current, max. 3.7 A
I²t 0.09 A²·s

Power
Infeed power to the backplane bus 4.5 W

Power loss
Power loss, typ. 1.9 W

Address area
Address space per module
● Address space per module, max. 256 byte; per input / output
Address space per station
● Address space per station, max. 512 byte; Dependent on configuration

Hardware configuration
Rack
● Modules per rack, max. 32; + 16 ET 200AL modules
Submodules
● Number of submodules per station, max. 256

Interfaces
Number of PROFINET interfaces 1; 2 ports (switch)

1. Interface
Interface types
● Number of ports 2
● integrated switch Yes
● RJ 45 (Ethernet) Yes; Pre-assembled BusAdapter BA 2x RJ45
● BusAdapter (PROFINET) Yes; Applicable BusAdapter: BA 2x RJ45, BA 2x FC
Protocols
● PROFINET IO Device Yes
● Open IE communication Yes
● Media redundancy Yes; PROFINET MRP

Interface types
RJ 45 (Ethernet)
● Transmission procedure PROFINET with 100 Mbit/s full duplex (100BASE-TX)
● 10 Mbps Yes; for Ethernet services
● 100 Mbps Yes; PROFINET with 100 Mbit/s full duplex (100BASE-TX)
● Autonegotiation Yes

6AG1155-6AA01-7BN0 Subject to change without notice

Page 2/5 04/16/2020 © Copyright Siemens
 ● Autocrossing Yes

Protocols
PROFINET IO Device
Services
— Isochronous mode No
— Open IE communication Yes
— IRT Yes; with send cycles of between 250 µs and 4 ms in increments
of 125 µs
— PROFIenergy Yes
— Prioritized startup Yes
— Shared device Yes
— Number of IO Controllers with shared 2
device, max.
Redundancy mode
● PROFINET system redundancy (S2) No
Media redundancy
— MRP Yes
— MRPD No
Open IE communication
● TCP/IP Yes
● SNMP Yes
● LLDP Yes

Isochronous mode
Isochronous operation (application synchronized up No
to terminal)

Interrupts/diagnostics/status information
Status indicator Yes
Alarms Yes
Diagnostics function Yes
Diagnostics indication LED
● RUN LED Yes; green LED
● ERROR LED Yes; red LED
● MAINT LED Yes; Yellow LED
● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED
● Connection display LINK TX/RX Yes; 2x green link LEDs on BusAdapter

Potential separation
between backplane bus and electronics No
between PROFINET and all other circuits Yes; 1 500 V AC
between supply and all other circuits No

Permissible potential difference

between different circuits Safety extra low voltage SELV

6AG1155-6AA01-7BN0 Subject to change without notice

Page 3/5 04/16/2020 © Copyright Siemens
 Standards, approvals, certificates
Network loading class 2
Security level According to Security Level 1 Test Cases V1.1.1

Ambient conditions
Ambient temperature during operation
● horizontal installation, min. -40 °C; = Tmin (incl. condensation/frost)
● horizontal installation, max. 70 °C; = Tmax
● vertical installation, min. -40 °C; = Tmin
● vertical installation, max. 50 °C; = Tmax
Altitude during operation relating to sea level
● Installation altitude above sea level, max. 5 000 m
● Ambient air temperature-barometric pressure- Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) //
altitude Tmin ... (Tmax - 10 K) at 795 hPa ... 658 hPa (+2 000 m ... +3 500
m) // Tmin ... (Tmax -20 K) at 658 hPa ... 540 hPa (+3 500 m ... +5
000 m)
Relative humidity
● With condensation, tested in accordance with 100 %; RH incl. condensation / frost (no commissioning in
IEC 60068-2-38, max. bedewed state), horizontal installation
Resistance
Coolants and lubricants
— Resistant to commercially available Yes; Incl. diesel and oil droplets in the air
coolants and lubricants
Use in stationary industrial systems
— to biologically active substances according Yes; Class 3B2 mold, fungus and dry rot spores (with the
to EN 60721-3-3 exception of fauna); Class 3B3 on request
— to chemically active substances according Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-
to EN 60721-3-3 52 (severity degree 3); *
— to mechanically active substances Yes; Class 3S4 incl. sand, dust, *
according to EN 60721-3-3
Use on ships/at sea
— to biologically active substances according Yes; Class 6B2 mold and fungal spores (excluding fauna); Class
to EN 60721-3-6 6B3 on request
— to chemically active substances according Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-
to EN 60721-3-6 52 (severity degree 3); *
— to mechanically active substances Yes; Class 6S3 incl. sand, dust; *
according to EN 60721-3-6
Usage in industrial process technology
— Against chemically active substances acc. Yes; Class 3 (excluding trichlorethylene)
to EN 60654-4
— Environmental conditions for process, Yes; Level GX group A/B (excluding trichlorethylene; harmful gas
measuring and control systems acc. to concentrations up to the limits of EN 60721-3-3 class 3C4
ANSI/ISA-71.04 permissible); level LC3 (salt spray) and level LB3 (oil)
Remark

6AG1155-6AA01-7BN0 Subject to change without notice

Page 4/5 04/16/2020 © Copyright Siemens
 — Note regarding classification of * The supplied plug covers must remain in place over the unused
environmental conditions acc. to EN 60721, interfaces during operation!
EN 60654-4 and ANSI/ISA-71.04
Conformal coating
● Coatings for printed circuit board assemblies Yes; Class 2 for high reliability
acc. to EN 61086
● Protection against fouling acc. to EN 60664-3 Yes; Type 1 protection
● Military testing according to MIL-I-46058C, Yes; Discoloration of coating possible during service life
Amendment 7
● Qualification and Performance of Electrical Yes; Conformal coating, Class A
Insulating Compound for Printed Board
Assemblies according to IPC-CC-830A

Connection method
ET-Connection
● via BU/BA Send Yes; + 16 ET 200AL modules

Dimensions
Width 50 mm
Height 117 mm
Depth 74 mm

Weights
Weight, approx. 190 g; IM 155-6 PN BA with 2x RJ45 ports and server module

last modified: 04/11/2020

6AG1155-6AA01-7BN0 Subject to change without notice

Page 5/5 04/16/2020 © Copyright Siemens